There is no need to maintain the DPP authentication state if config
request processing fails, so clear state also in the GAS server request
handler similarly to the other failure cases.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The hwsim test cases are trying to clear this parameter between test
cases, but that was not really done correctly for many of the sigma_dut
test cases. Instead of fixing the text scripts to do this more
carefully, it seems to be simpler to just force the FLUSH command to
clear this.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is needed since the gas_query_req() operation could remain waiting
indefinitely for the response if the Configurator keeps sending out
comeback responses with additional delay. The DPP technical
specification expects the Enrollee to continue sending out new Config
Requests for 60 seconds, so this gives an extra 60 second time after the
last expected new Config Request for the Configurator to determine what
kind of configuration to provide.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Instead of depending on the TX-wait-response-time to be sufficient to
cover the full GAS exchange, start an ongoing listen operation on the
negotiation channel (if no such listen operation is already in place) to
allow the configuration exchange to take longer amount of time. This is
needed for cases where the conf=query is used to request Configurator
parameters from upper layers and that upper layer processing (e.g., user
interaction) takes significant amount of time.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Once the GO/AP interface initialization is completed, check if the
operating frequency set in the wpa_supplicant group interface structure
is different than the one set in the hostapd interface structure
associated with the group interface. If yes, update the frequency in the
wpa_supplicant group interface and network configuration to the
frequency set in the hostapd interface structure.
The frequency set in the hostapd interface is the correct/final
frequency wpa_supplicant configured in the kernel/driver. This is done
because wpa_supplicant may switch the initially requested primary and
secondary frequencies to get a secondary frequency with no beacons (to
avoid interference or 20/40 MHz coex logic). And the updated frequency
is informed by the driver only after the interface setup is completed
through the channel switch event - EVENT_CH_SWITCH. But wpa_supplicant
updates the frequency to applications through the P2P_GROUP_STARTED
event which is triggered before the EVENT_CH_SWITCH event. To send the
correct frequency to applications the frequency must be updated before
sending the P2P_GROUP_STARTED event.
Bug: 191272346
Test: Manual - Verified that GO frequency is updated and reported
correctly to Nearby application.
Signed-off-by: Sunil Ravi <sunilravi@google.com>
This provides an alternative mechanism for upper layer components to
control configuration parameters to be used by the local Configurator.
Instead of the previously used design where the Configurator parameters
had to be provided before initiating the DPP Authentication exchange,
the new alternative approach allows the DPP Authentication exchange to
be started before any Configurator parameters have been determined and
wpa_supplicant will then request the parameters once the DPP
Configuration Request has been received from the Enrollee. This allows
the Config Request information to be used at upper layers to determine
how the Enrollee should be configured.
For example for an Initiator:
CTRL: DPP_QR_CODE <URI from Responder/Enrollee>
CTRL: DPP_AUTH_INIT peer=1 conf=query
<3>DPP-CONF-NEEDED peer=1 src=02:00:00:00:00:00 net_role=sta name="Test" opclass=81,82,83,84,115,116,117,118,119,120,121,122,123,124,125,126,127,128,129,130 mud_url=N/A
(upper layer processing; potentially including user interaction)
CTRL: DPP_CONF_SET peer=1 conf=sta-sae ssid=736165 pass=70617373776f7264
<3>DPP-CONF-SENT
For example for a Responder:
CTRL: SET dpp_configurator_params conf=query
CTRL: DPP_LISTEN 2412 role=configurator
<3>DPP-CONF-NEEDED peer=2 src=02:00:00:00:01:00 net_role=sta name="Test" opclass=81,82,83,84,115,116,117,118,119,120,121,122,123,124,125,126,127,128,129,130 mud_url=N/A
(upper layer processing; potentially including user interaction)
CTRL: DPP_CONF_SET peer=2 conf=sta-sae ssid=736165 pass=70617373776f7264
<3>DPP-CONF-SENT
For example for an Initiator that can act both as a Configurator and an
Enrollee in a case where the Initiator becomes the Enrollee:
CTRL: DPP_AUTH_INIT peer=1 role=either conf=query
<3>DPP-CONF-RECEIVED
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Extend the GAS server functionality to allow a request handler to return
the initial comeback delay with a later callback instead of having to
indicate the comeback delay when returning from the handler function.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The TCP code path did not handle the postponed connection attempt on TX
status and the following result message from the Enrollee to the
Configurator. Fix this by adding TCP-versions of these operations to
match the way wpa_supplicant implemented this for the Public Action
frames.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This extends dpp_test functionality to allow DPP Network Introduction
exchanges to use an incorrect value in the Protocol Version attribute.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Use a separate ver=<1|2> parameter to DPP_PKEX_ADD instead of
overloading init=1 with version indication. This allows additional
options for forcing v1-only and v2-only in addition to automatic mode
(start with v2 and fall back to v1, if needed).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Use automatic PKEX version negotiation as the initiator by starting with
PKEXv2 and if no response is received, trying again with PKEXv1. For
now, this is enabled only in wpa_supplicant CONFIG_DPP3=y builds.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The rx_freq of Public Action frame was not maintained by the GO and the
GO always sent the response on the operating channel. This causes
provision discovery failure when a P2P Device is sending a PD Request on
a 2.4 GHz social channel and the GO is responding on a 5 GHz operating
channel.
Save the rx_freq and use it for GO to sent the response. This extends
commit c5cc7a59ac ("Report offchannel RX frame frequency to hostapd")
to cover additional frame types.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Update the version number for the build and also add the ChangeLog
entries for both hostapd and wpa_supplicant to describe main changes
between v2.9 and v2.10.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like the recently added roam_in_progress and
bss_trans_mgmt_in_progress flags could end up getting set, but not
cleared, in some cases. Make sure these get cleared on explicit
disconnection request and also in case the SME-in-driver path is used
(while that path does not really use these flags yet, it is better to
not allow them to be forgotten to be set should it be extended to cover
similar functionality).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
After receiving a BSS Transition Management request,
wpa_supplicant_connect() will abort ongoing scans, which will cause scan
results to be reported. Since the reassociate bit is set, this will
trigger a connection attempt based on the aborted scan's scan results
and cancel the initial connection request. This often causes
wpa_supplicant to reassociate to the same AP it is currently associated
to instead of the AP it was asked to transition to.
Add a bss_trans_mgmt_in_progress flag to indicate that we're currently
transitioning to a different AP so that we don't initiate another
connection attempt based on the possibly received scan results from a
scan that was in progress at the time the BSS Transition Management
request was received.
This is the equivalent of commit 5ac977758d ("Reject authentication
start during explicit roam requests") for the roaming scenario.
Signed-off-by: Nicolas Norvez <norvez@chromium.org>
Make wpas_dbus_handler_interworking_select() conditional on
CONFIG_INTERWORKING to avoid compilation issues.
Fixes: c8e4283f90 ("D-Bus: Interworking network selection")
Signed-off-by: Alex Kiernan <alexk@zuma.ai>
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
The radio work starting may be delayed. If the DPP listen operation is
stopped before the radio work starts, the pending dpp-listen radio work
won't get cleaned up, which might lead to failing to start the next DPP
listen operation.
Issue scenario: DPP start -> dpp-listen radio work added but not started
-> DPP stop, pending radio work not cleaned up -> radio work start ->
trying to start DPP but failing because a dpp-listen work already
exists.
This commit removes the potential pending dpp-listen radio
work when DPP stops.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
wpa_supplicant may use wrong SAE authentication method if it doesn't
have the scan result for the target BSS since RSNXE information is not
available.
For example, STA might use the hunting-and-pecking loop method for SAE
authentication even though AP supports SAE H2E and STA is configured
with sae_pwe=2.
This is possible in cases like EXTERNAL_AUTH triggered by the driver
during roaming. To avoid this update scan results to fetch the target
BSS scan result from the driver.
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
Allow mesh_fwding (dot11MeshForwarding) to be specified in a mesh BSS
config, pass that to the driver (only nl80211 implemented for now) and
announce forwarding capability accordingly.
Signed-off-by: José Pekkarinen <jose.pekkarinen@unikie.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add the "InterworkingSelect" method to the DBus API to trigger an
Interworking scan with ANQP fetches. When a BSS that matches a
configured credential is found, the result is emitted using the signal
"InterworkingAPAdded". Completion of the full InterworkingSelect
operation is indicated with the "InterworkingSelectDone" signal.
Signed-off-by: Damien Dejean <damiendejean@chromium.org>
Add "AddCred", "RemoveCred", and "RemoveAllCreds" methods to the D-Bus
API of the network interface to allow the caller to manipulate a set of
Interworking credentials similarly to the way this was enabled through
the control interface.
Signed-off-by: Damien Dejean <damiendejean@chromium.org>
This allows the same functions to be used for both the control interface
and the D-Bus interface.
Signed-off-by: Damien Dejean <damiendejean@chromium.org>
Add the support of engine, engine_id, ca_cert_id, cert_id, and key_id
parameters to credential blocks for Hotspot 2.0.
Signed-off-by: Damien Dejean <damiendejean@chromium.org>
The P2P DBus interface was using the wrong interface name when calling
wpas_p2p_invite_group(). Capture the group interface name before calling
the method to fix this.
Signed-off-by: Hicham Hassoubi <Hicham_hassoubi@bose.com>
This reverts commit 3204795d7a.
The commit adds an additional check that checks for overlapping BSSs in
addition to the existing 40 MHz intolerance subfield checks. The commit
cites IEEE Std 802.11-2016, 11.16.12, which defines the proper behavior
for a 20/40 MHz HT STA and AP, but the standard actually doesn't say
anything about overlapping BSSs. Specifically, the standard states that
the only BSSs that belong in the Intolerant channel report are those
that satisfy trigger event A, defined as channels with BSSs that don't
contain the HT capabilities element (which wpa_supplicant already did
before). Note that we also include channels with BSSs that have the 40
MHz intolerance bit set in the Intolerant channel report.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
Add support for PKEXv2 core protocol. This defines a new PKEX Exchange
Request message type with protocol negotiation and different rules for
key derivation with PKEXv2 or newer is used.
This does not change existing behavior for PKEX, i.e., the PKEXv1
variant will still be used by default.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Allow the dpp_test parameter to be used to request the Protocol Version
attributed to be omitted from the Peer Discovery Request/Response
message.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Verify that the Protocol Version attribute is used appropriate in Peer
Discovery Request/Response messages in cases where the signed Connector
includes the version information.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Generate Peer Discovery Request/Response messages using the protected
version from the Connector, if present, instead of the currently
supported protocol version which might be higher than the one that got
included into the signed Connector during provisioning earlier.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
CONFIG_DPP3=y can now be used to configure hostapd and wpa_supplicant
builds to include DPP version 3 functionality. This functionality is
still under design and the implementation is experimental and not
suitable to be enabled in production uses before the specification has
been finalized.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Align the process logic for ap_vendor_elements and ap_assocresp_elements
parsing by using the wpabuf_parse_bin() helper function in both.
Signed-off-by: Chaoli Zhou <zchaoli@codeaurora.org>
wpa_add_scan_freqs_list() was updated to use bool for the is_6ghz
argument, but these callers were missed when updating the values from
0/1 to false/true.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The channels included for the scan to connect to a P2P GO are optimized
such that the P2P GO preferred channel and the common channels are
included for the first few scans followed by a full scan in which all
the channels supported by the local device are included. This results in
P2P client including the 6 GHz channels for the full scan after GO
Negotiation even when 6 GHz channels are not used for the P2P
connection.
Exclude the 6 GHz channels from the full scan if 6 GHz channels are
supported but are not used for P2P connection.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
After roaming to a new AP using driver-based SME and roaming trigger,
update proto type, AKMP suite, and pairwise cipher suite based on the
(Re)Association Request frame. Update PMF, group cipher, and group mgmt
cipher based on the AP's RSNE into wpa_sm. group_mgmt_cipher needs to be
updated based on PMF capabilities of STA and roamed AP.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Since the 6 GHz band has no DFS channels, enable 6 GHz 160 MHz bandwidth
as the default configuration for IEEE 802.11s mesh.
example:
network={
ssid="6gmesh160"
key_mgmt=SAE
mode=5
frequency=6275
psk="1234567890"
}
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
IEEE Std 802.11ax-2021 mandates 6 GHz STA to use Management Frame
Protection (MFP) when RSN is enabled.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Channel numbers of the 6 GHz band overlap those of the 2.4 GHz and 5 GHz
bands. Thus converting to frequency based mesh channel selection helps
accommodate 6 GHz mesh.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
After roaming to a new AP using driver-based SME and roaming trigger,
AKMP and proto were not updated in wpa_sm. Hence, update AKMP and proto
used with roamed AP when association event received from the driver in
SME offloaded to the driver scenario to avoid incorrect AKMP details in
wpa_supplicant similarly to how the cipher suite updates were added in
commit 2b3e64a0fb ("Update ciphers to address GTK renewal failures
while roaming") .
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Wi-Fi Display functionality needs P2P to be enabled. Ignore
CONFIG_WIFI_DISPLAY if CONFIG_P2P is not enabled for the build. This
avoids following compilation issue with invalid build configuration:
../src/ap/ap_drv_ops.c: In function 'hostapd_build_ap_extra_ies':
../src/ap/ap_drv_ops.c:163:10: error: 'struct hostapd_data' has no member named 'p2p_group'
163 | if (hapd->p2p_group) {
| ^~
../src/ap/ap_drv_ops.c:165:35: error: 'struct hostapd_data' has no member named 'p2p_group'
165 | a = p2p_group_assoc_resp_ie(hapd->p2p_group, P2P_SC_SUCCESS);
| ^~
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Commit b0f457b619 ("SAE: Do not expire the current PMKSA cache entry")
depends on sm->cur_pmksa to determine if it is the current PMKSA cache
entry, but sm->cur_pmksa was not always correct for SAE in the current
implementation.
Set sm->cur_pmksa in wpa_sm_set_pmk() (which is used with SAE), and skip
clearing of sm->cur_pmksa for SAE in wpa_find_assoc_pmkid(). This latter
case was added by commit c2080e8657 ("Clear current PMKSA cache
selection on association/roam") for driver-based roaming indication and
Suite B, so skipping it for SAE should be fine.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Using pkg-config for libpcsclite can provide more accurate linking
flags.
Signed-off-by: Reinhard Tartler <siretart@tauware.de>
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Make sure that D-Bus isn't shut down before wpa_supplicant, as that would
also bring down wireless links which are still holding open NFS shares.
Debian bug: https://bugs.debian.org/785579
systemd upstream bug: https://bugs.freedesktop.org/show_bug.cgi?id=89847
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Every usage of these variables appends an extra slash, so keeping
a slash in the default values leads to double slashes in resulting
paths.
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>