The new sae_pwe=3 mode can be used to test non-compliant behavior with
SAE Password Identifiers. This can be used to force use of
hunting-and-pecking loop for PWE derivation when Password Identifier is
used. This is not allowed by the standard and as such, this
functionality is aimed at compliance testing.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Application Extension attribute is defined in WSC tech spec v2.07 page
104. Allow hostapd to be configured to add this extension into WPS IE in
Beacon and Probe Response frames. The implementation is very similar to
vendor extension.
A new optional entry called "wps_application_ext" is added to hostapd
config file to configure this. It enodes the payload of the Application
Extension attribute in hexdump format.
Signed-off-by: Veli Demirel <veli.demirel@airties.com>
Signed-off-by: Bilal Hatipoglu <bilal.hatipoglu@airties.com>
The new hostapd gtk_rsc_override and igtk_rsc_override configuration
parameters can be used to set an override value for the RSC that the AP
advertises for STAs for GTK/IGTK. The contents of those parameters is a
hexdump of the RSC in little endian byte order.
This functionality is available only in CONFIG_TESTING_OPTIONS=y builds.
This can be used to verify that stations implement initial RSC
configuration correctly for GTK/ and IGTK.
Signed-off-by: Jouni Malinen <j@w1.fi>
The channel numbers are duplicated between 2.4 GHz / 5 GHz bands and 6
GHz band. Hence, add support to configure a list of frequencies to ACS
(freqlist) instead of a list of channel numbers (chanlist). Also, both 5
GHz and 6 GHz channels are referred by HOSTAPD_MODE_IEEE80211A. The 6
GHz channels alone can be configured by using both mode and frequency
list.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This new hostapd configuration parameter rsnxe_override_eapol=<hexdump>
can be used to override RSNXE value in EAPOL-Key msg 3/4 for testing
purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previously, nonzero sae_h2e parameter values were used to perform SAE
H2E specific operations (deriving PT, adding RSNXE, adding H2E-only BSS
membership selector) in AP mode even if SAE was not enabled for the
network. This could result in unexpected behavior if sae_pwe=1 or
sae_pwe=2 were set in the configuration. Fix this by making the SAE
operations conditional on SAE being actually enabled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new hostapd and wpa_supplicant configuration parameters dpp_name and
dpp_mud_url can now be used to set a specific name and MUD URL for the
Enrollee to use in the Configuration Request. dpp_name replaces the
previously hardcoded "Test" string (which is still the default if an
explicit configuration entry is not included). dpp_mud_url can
optionally be used to add a MUD URL to describe the Enrollee device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Hardcode this to be defined and remove the separate build options for
PMF since this functionality is needed with large number of newer
protocol extensions and is also something that should be enabled in all
WPA2/WPA3 networks.
Signed-off-by: Jouni Malinen <j@w1.fi>
Allow the previously hardcoded maximum numbers of EAP message rounds to
be configured in hostapd EAP server. This can be used, e.g., to increase
the default limits if very large X.509 certificates are used for EAP
authentication.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd configuration option eap_sim_id can now be used to
disable use of pseudonym and/or fast reauthentication with EAP-SIM,
EAP-AKA, and EAP-AKA'.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add an SQLite table for defining per station MAC address version of
radius_auth_req_attr/radius_acct_req_attr information. Create the
necessary table and index where this doesn't exist. Select attributes
from the table keyed by station MAC address and request type (auth or
acct), parse and apply to a RADIUS message.
Add radius_req_attr_sqlite hostapd config option for SQLite database
file. Open/close RADIUS attribute database for a lifetime of a BSS and
invoke functions to add extra attributes during RADIUS auth and
accounting request generation.
Signed-off-by: Terry Burton <tez@terryburton.co.uk>
We will want to parse RADIUS attributes in config file format when
retrieving them from an SQLite database.
Signed-off-by: Terry Burton <tez@terryburton.co.uk>
hostapd EAP server can now be configured with two separate server
certificates/keys to enable parallel operations using both RSA and ECC
public keys. The server will pick which one to use based on the client
preferences for the cipher suite (in the TLS ClientHello message). It
should be noted that number of deployed EAP peer implementations do not
filter out the cipher suite list based on their local configuration and
as such, configuration of alternative types of certificates on the
server may result in interoperability issues.
Signed-off-by: Jouni Malinen <j@w1.fi>
Declare the variable only once and reuse it instead of openning
unneeded scopes.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add a config option to allow setting a custom Basic NSS/MCS set. As a
default we use single stream HE-MCS 0-7.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
This adds support to hostapd for configuring airtime policy settings for
stations as they connect to the access point. This is the userspace
component of the airtime policy enforcement system PoliFi described in
this paper: https://arxiv.org/abs/1902.03439
The Linux kernel part has been merged into mac80211 for the 5.1 dev
cycle.
The configuration mechanism has three modes: Static, dynamic and limit.
In static mode, weights can be set in the configuration file for
individual MAC addresses, which will be applied when the configured
stations connect.
In dynamic mode, weights are instead set per BSS, which will be scaled
by the number of active stations on that BSS, achieving the desired
aggregate weighing between the configured BSSes. Limit mode works like
dynamic mode, except that any BSS *not* marked as 'limited' is allowed
to exceed its configured share if a per-station fairness share would
assign more airtime to that BSS. See the paper for details on these
modes.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
IEEE P802.11ax/D4.0 9.4.2.243 "HE Operation element" indicates that the
special value 1023 in the TXOP Duration RTS Threshold field is used to
indicate that TXOP duration-based RTS is disabled. Use that value as the
default instead of the previously used value 0 which would really mean
threshold of 0 usec. Furthermore, the previous implementation did not
allow values larger than 255 to be used for this field while the field
is actually 10 bits in size.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
The new hostapd configuration parameter dpp_controller can now be used
with the following subparameter values: ipaddr=<IP address>
pkhash=<hexdump>. This adds a new Controller into the configuration
(i.e., more than one can be configured) and all incoming DPP exchanges
that match the specified Controller public key hash are relayed to the
particular Controller.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
hostapd configuration parameters fragm_threshold and rts_threshold were
documented to disable the threshold with value -1 and not change driver
configuration if the parameter is not included. However, -1 was mapped
into not changing the driver value, so the explicit disabling part did
not work.
Replace the default values for these to be -2 so that explicitly set
configuration value -1 can be distinguished from the case of not
including the parameter. Map the -1 value to a driver request to disable
the threshold. Ignore any error from this operation just in case to
avoid breaking functionality should some drivers not accept the (u32) -1
value as a threshold value request to disable the mechanism.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This patch added 'check_cert_subject' support to match the value of
every field against the DN of the subject in the client certificate. If
the values do not match, the certificate verification will fail and will
reject the user.
This option allows hostapd to match every individual field in the right
order, also allow '*' character as a wildcard (e.g OU=Development*).
Note: hostapd will match string up to 'wildcard' against the DN of the
subject in the client certificate for every individual field.
Signed-off-by: Paresh Chaudhary <paresh.chaudhary@rockwellcollins.com>
Signed-off-by: Jared Bents <jared.bents@rockwellcollins.com>
Signed-off-by: Jouni Malinen <j@w1.fi>
The Wi-Fi Alliance Multi-AP Specification v1.0 allows onboarding of a
backhaul STA through WPS. To enable this, the WPS Registrar offers a
different set of credentials (backhaul credentials instead of fronthaul
credentials) when the Multi-AP subelement is present in the WFA vendor
extension element of the WSC M1 message.
Add new configuration options to specify the backhaul credentials for
the hostapd internal registrar: multi_ap_backhaul_ssid,
multi_ap_backhaul_wpa_psk, multi_ap_backhaul_wpa_passphrase. These are
only relevant for a fronthaul SSID, i.e., where multi_ap is set to 2 or
3. When these options are set, pass the backhaul credentials instead of
the normal credentials when the Multi-AP subelement is present.
Ignore the Multi-AP subelement if the backhaul config options are not
set. Note that for an SSID which is fronthaul and backhaul at the same
time (i.e., multi_ap == 3), this results in the correct credentials
being sent anyway.
The security to be used for the backaul BSS is fixed to WPA2PSK. The
Multi-AP Specification only allows Open and WPA2PSK networks to be
configured. Although not stated explicitly, the backhaul link is
intended to be always encrypted, hence WPA2PSK.
To build the credentials, the credential-building code is essentially
copied and simplified. Indeed, the backhaul credentials are always
WPA2PSK and never use per-device PSK. All the options set for the
fronthaul BSS WPS are simply ignored.
Signed-off-by: Davina Lu <ylu@quantenna.com>
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Cc: Marianna Carrera <marianna.carrera.so@quantenna.com>
str_token() can return NULL for the name if the remaining token contains
only the delimiter. Fix this to avoid NULL pointer dereference with a
corner case of an invalid value used in the configuration.
Fixes: ec5c39a557 ("AP: Allow identifying which passphrase station used with wpa_psk_file")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Extend wpa_psk_file to allow an optional VLAN ID to be specified with
"vlanid=<VLAN ID>" prefix on the line. If VLAN ID is specified and the
particular wpa_psk_file entry is used for a station, that station is
bound to the specified VLAN. This can be used to operate a single
WPA2-Personal BSS with multiple VLANs based on the used passphrase/PSK.
This is similar to the WPA2-Enterprise case where the RADIUS server can
assign stations to different VLANs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
It is now possible to optionally specify keyid for
each wpa_psk_file entry:
keyid=something 00:00:00:00:00:00 secretpassphrase
When station connects and the passphrase it used
has an associated keyid it will be appended to the
AP-STA-CONNECTED event string:
wlan0: AP-STA-CONNECTED 00:36:76:21:dc:7b keyid=something
It's also possible to retrieve it through the control interface:
$ hostapd_cli all_sta
Selected interface 'ap0'
00:36:76:21:dc:7b
...
keyid=something
New hostapd is able to read old wpa_psk_file. However, old hostapd will
not be able to read the new wpa_psk_file if it includes keyids.
Signed-off-by: Michal Kazior <michal@plume.com>
Support the new Extended Capabilities field bits 81 and 82 to indicate
whether SAe Password Identifiers are in use.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
An AP might reject a STA association request due to low RSSI. In such
case, the AP informs the STA the desired RSSI improvement and a retry
timeout. The STA might retry to associate even if the RSSI hasn't
improved if the retry timeout expired.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Add the ability to ignore time-based CRL errors from OpenSSL by
specifying a new configuration parameter, check_crl_strict=0.
This causes the following:
- This setting does nothing when CRL checking is not enabled.
- When CRL is enabled, "strict mode" will cause CRL time errors to not
be ignored and will continue behaving as it currently does.
- When CRL is enabled, disabling strict mode will cause CRL time
errors to be ignored and will allow connections.
By default, check_crl_strict is set to 1, or strict mode, to keep
current functionality.
Signed-off-by: Sam Voss <sam.voss@rockwellcollins.com>
This makes it possible to use ECDSA certificates with EAP-TLS/TTLS/etc.
It should be noted that when using Suite B, different mechanism is used
to specify the allowed ECDH curves and this new parameter must not be
used in such cases.
Signed-off-by: Hristo Venev <hristo@venev.name>
This adds support for hostapd-as-RADIUS-authentication-server to request
subscription remediation for SIM-based credentials. The new hostapd.conf
parameter hs20_sim_provisioning_url is used to set the URL prefix for
the remediation server for SIM provisioning. The random
hotspot2dot0-mobile-identifier-hash value will be added to the end of
this URL prefix and the same value is stored in a new SQLite database
table sim_provisioning for the subscription server implementation to
use.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new hostapd configuration parameter hs20_release can be used to
configure the AP to advertise a specific Hotspot 2.0 release number
instead of the latest supported release. This is mainly for testing
purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Extend hostapd to allow the new OSU Provider NAI List ANQP-element to be
advertised in addition to the previously used OSU Providers list
ANQP-element. The new osu_nai2 configurator parameter option is used to
specify the OSU_NAI value for the shared BSS (Single SSID) case while
osu_nai remains to be used for the separate OSU BSS.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
These changes add support for salted password databases to EAP-pwd per
RFC 8146. This commits introduces the framework for enabling this and
the salting mechanisms based on SHA-1, SHA256, and SHA512 hash
algorithms.
Signed-off-by: Dan Harkins <dharkins@lounge.org>
This extends the SAE implementation in both infrastructure and mesh BSS
cases to allow an optional Password Identifier to be used. This uses the
mechanism added in P802.11REVmd/D1.0. The Password Identifier is
configured in a wpa_supplicant network profile as a new string parameter
sae_password_id. In hostapd configuration, the existing sae_password
parameter has been extended to allow the password identifier (and also a
peer MAC address) to be set. In addition, multiple sae_password entries
can now be provided to hostapd to allow multiple per-peer and
per-identifier passwords to be set.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The current EAP peer implementation is not yet ready for the TLS v1.3
changes with EAP-TTLS, EAP-PEAP, and EAP-FAST, so disable TLS v1.3 for
this EAP method for now.
While the current EAP-TLS implementation is more or less complete for
TLS v1.3, there has been no interoperability testing with other
implementations, so disable for by default for now until there has been
chance to confirm that no significant interoperability issues show up
with TLS version update. tls_flags=[ENABLE-TLSv1.3] configuration
parameter can be used to enable TLS v1.3 (assuming the TLS library
supports it; e.g., when using OpenSSL 1.1.1).
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends hostapd Access-Accept processing to check if the RADIUS
server indicated that Terms and Conditions Acceptance is required. The
new hs20_t_c_server_url parameter is used to specify the server URL
template that the STA is requested to visit.
This commit does not enable any kind of filtering, i.e., only the part
of forwarding a request from Access-Accept to the STA using
WNM-Notification is covered.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends hostapd with two new configuration parameters
(hs20_t_c_filename and hs20_t_c_timestamp) that can be used to specify
that the Terms and Conditions attributes are to be added into all
Access-Request messages for Hotspot 2.0 STAs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends hostapd Hotspot 2.0 implementation to allow operator icons
to be made available. The existing hs20_icon parameter is used to define
the icons and the new operator_icon parameter (zero or more entries) is
used to specify which of the available icons are operator icons. The
operator icons are advertised in the Operator Icon Metadata ANQP-element
while the icon data can be fetched using the same mechanism (icon
request/binary file) that was added for the OSU Providers icons.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new configuration option ft_r0_key_lifetime that deprecates
r0_key_lifetime. Though, the old configuration is still accepted for
backwards compatibility.
This simplifies testing. All other items are in seconds as well. In
addition, this makes dot11FTR0KeyLifetime comment match with what got
standardized in the end in IEEE Std 802.11r-2008.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
The new venue_url parameter can now be used to set the Venue URL ANQP
information instead of having to construct the data and use
anqp_elem=277:<hexdump> to set the raw value.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new hostapd.conf parameter sae_sync (default: 5) can now be used to
configure the dot11RSNASAESync value to specify the maximum number of
synchronization errors that are allowed to happen prior to
disassociation of the offending SAE peer.
Signed-off-by: Jouni Malinen <j@w1.fi>
Extend the check against WPA/TKIP only configuration by adding CCMP-256
and GCMP-256 to the list of allowed ciphers. This is needed to allow WPS
to be enabled in AP configurations where neither CCMP-128 nor GCMP-128
are enabled.
Signed-off-by: Shiva Sankar Gajula <sgajula@qti.qualcomm.com>
The new hostapd configuration parameter group_cipher can now be used to
override the automatic cipher selection based on enabled pairwise
ciphers. It should be noted that selecting an unexpected group cipher
can result in interoperability issues and this new capability is mainly
for testing purposes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a new hostapd configuration parameter
wpa_disable_eapol_key_retries=1 that can be used to disable
retransmission of EAPOL-Key frames that are used to install
keys (EAPOL-Key message 3/4 and group message 1/2). This is
similar to setting wpa_group_update_count=1 and
wpa_pairwise_update_count=1, but with no impact to message 1/4
retries and with extended timeout for messages 4/4 and group
message 2/2 to avoid causing issues with stations that may use
aggressive power saving have very long time in replying to the
EAPOL-Key messages.
This option can be used to work around key reinstallation attacks
on the station (supplicant) side in cases those station devices
cannot be updated for some reason. By removing the
retransmissions the attacker cannot cause key reinstallation with
a delayed frame transmission. This is related to the station side
vulnerabilities CVE-2017-13077, CVE-2017-13078, CVE-2017-13079,
CVE-2017-13080, and CVE-2017-13081.
This workaround might cause interoperability issues and reduced
robustness of key negotiation especially in environments with
heavy traffic load due to the number of attempts to perform the
key exchange is reduced significantly. As such, this workaround
is disabled by default (unless overridden in build
configuration). To enable this, set the parameter to 1.
It is also possible to enable this in the build by default by
adding the following to the build configuration:
CFLAGS += -DDEFAULT_WPA_DISABLE_EAPOL_KEY_RETRIES=1
Signed-off-by: Jouni Malinen <j@w1.fi>
The new sae_password hostapd configuration parameter can now be used to
set the SAE password instead of the previously used wpa_passphrase
parameter. This allows shorter than 8 characters and longer than 63
characters long passwords to be used. In addition, this makes it
possible to configure a BSS with both WPA-PSK and SAE enabled to use
different passphrase/password based on which AKM is selected.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new hostapd configuration parameter owe_groups can be used to
specify a subset of the allowed DH groups as a space separated list of
group identifiers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new sae_commit_override=<hexdump> parameter can be used to force
hostapd to override SAE commit message fields for testing purposes. This
is included only in CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The default value for GTK rekeying period was previously hardcoded to
600 seconds for all cases. Leave that short value only for TKIP as group
cipher while moving to the IEEE 802.11 default value of 86400 seconds
(once-per-day) for CCMP/GCMP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend hostapd configuration to include parameters needed for the DPP
AKM: dpp_connector, dpp_netaccesskey, dpp_netaccesskey_expiry,
dpp_csign, dpp_csign_expiry.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Enable use of FT RRB without configuring each other AP locally. Instead,
broadcast messages are exchanged to discover APs within the local
network.
When an R0KH or R1KH is discovered, it is cached for one day.
When a station uses an invalid or offline r0kh_id, requests are always
broadcast. In order to avoid this, if r0kh does not reply, a temporary
blacklist entry is added to r0kh_list.
To avoid blocking a valid r0kh when a non-existing pmk_r0_name is
requested, r0kh is required to always reply using a NAK. Resend requests
a few times to ensure blacklisting does not happen due to small packet
loss.
To free newly created stations later, the r*kh_list start pointer in
conf needs to be updateable from wpa_auth_ft.c, where only wconf is
accessed.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This extends the GAS server to process MBO ANQP-elements and reply to a
query for the Cellular Data Connection Preference (if configured). The
new configuration parameter mbo_cell_data_conn_pref can be used to set
the value (0, 1, or 255) for the preference to indicate.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new hostapd.conf parameter country3 can now be used to configure the
third octet of the Country String that was previously hardcoded to ' '
(= 0x20).
For example:
All environments of the current frequency band and country (default)
country3=0x20
Outdoor environment only
country3=0x4f
Indoor environment only
country3=0x49
Noncountry entity (country_code=XX)
country3=0x58
IEEE 802.11 standard Annex E table indication: 0x01 .. 0x1f
Annex E, Table E-4 (Global operating classes)
country3=0x04
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new broadcast_deauth parameter can be used to disable sending of the
Deauthentication frame whenever AP is started or stopped. The default
behavior remains identical to the past behavior (broadcast_deauth=1).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_group_update_count and wpa_pairwise_update_count can now be used to
set the GTK and PTK rekey retry limits (dot11RSNAConfigGroupUpdateCount
and dot11RSNAConfigPairwiseUpdateCount). Defaults set to current
hardcoded value (4).
Some stations may suffer from frequent deauthentications due to GTK
rekey failures: EAPOL 1/2 frame is not answered during the total timeout
period of currently ~3.5 seconds. For example, a Galaxy S6 with Android
6.0.1 appears to go into power save mode for up to 5 seconds. Increasing
wpa_group_update_count to 6 fixed this issue.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
The new dhcp_server configuration parameter can now be used to configure
hostapd to act as a DHCP relay for DHCPDISCOVER messages received as
FILS HLP requests. The dhcp_rapid_commit_proxy=1 parameter can be used
to configure hostapd to convert 4 message DHCP exchange into a 2 message
exchange in case the DHCP server does not support DHCP rapid commit
option.
The fils_hlp_wait_time parameter can be used to set the time hostapd
waits for an HLP response. This matches the dot11HLPWaitTime in IEEE Std
802.11ai-2016.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The actual BSS configuration parameter can be updated with the SET
control interface command, so there is no need to maintain a separate
per-BSS parameter and a separate control interface handling for this.
Signed-off-by: Jouni Malinen <j@w1.fi>
This function is already checking the fname argument against NULL, so
use that check on its own instead of duplicating the check in the only
caller.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd configuration parameter fils_realm=<realm> can now be
used to configure one or more FILS realms to advertise for ERP domains
when using FILS. This replaces the use of erp_domain=<domain> parameter
for the FILS use case.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, CONFIG_IEEE80211R enabled build that supports FT for both
station mode and AP mode. However, in most wpa_supplicant cases only
station mode FT is required and there is no need for AP mode FT.
Add support to differentiate between station mode FT and AP mode FT in
wpa_supplicant builds by adding CONFIG_IEEE80211R_AP that should be used
when AP mode FT support is required in addition to station mode FT. This
allows binary size to be reduced for builds that require only the
station side FT functionality.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This has already been done for WEP, but there's same constraint for not
allowing VTH rates in case of TKIP.
Signed-off-by: Filip Matusiak <filip.matusiak@tieto.com>
This new parameter allows hostapd to add Vendor Specific elements into
(Re)Association Response frames similarly to the way vendor_elements
parameter can be used for Beacon and Probe Response frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to maintain two implementations of the functionality.
is_zero_ether_addr() is easier to understand, so use it.
Signed-off-by: Jouni Malinen <j@w1.fi>
If WPA2 and MBO are enabled, PMF needs to be enabled in hostapd
configuration. If PMF is optional in the configuration, an MBO STA is
required to negotiate use of PMF.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
1. Add tagged VLAN to struct vlan_description
(compile limited number of tagged VLANs per description)
For k tagged VLANs, the first k entries in vlan_description.tagged
are used. They are sorted in ascending order. All other entries are
zero. This way os_memcmp() can find identical configurations.
2. Let tagged VLANs be parsed from RADIUS Access-Accept
3. Print VLAN %d+ with %d=untagged VID if tagged VLANs are set
4. Select an unused vlan_id > 4096 for new tagged VLAN configurations
5. Add EGRESS_VLAN RADIUS attribute parsing also for untagged VLANs
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Separate uplink configuration (IEEE 802.1q VID) and grouping of stations
into AP_VLAN interfaces.
The int vlan_id will continue to identify the AP_VLAN interface the
station should be assigned to. Each AP_VLAN interface corresponds to an
instance of struct hostapd_vlan that is uniquely identified by int
vlan_id within an BSS.
New: Each station and struct hostapd_vlan holds a struct
vlan_description vlan_desc member that describes the uplink
configuration requested. Currently this is just an int untagged IEEE
802.1q VID, but can be extended to tagged VLANs and other settings
easily.
When the station was about to be assigned its vlan_id, vlan_desc and
vlan_id will now be set simultaneously by ap_sta_set_vlan(). So
sta->vlan_id can still be tested for whether the station needs to be
moved to an AP_VLAN interface.
To ease addition of tagged VLAN support, a member notempty is added to
struct vlan_description. Is is set to 1 if an untagged or tagged VLAN
assignment is requested and needs to be validated. The inverted form
allows os_zalloc() to initialize an empty description.
Though not depended on by the code, vlan_id assignment ensures:
* vlan_id = 0 will continue to mean no AP_VLAN interface
* vlan_id < 4096 will continue to mean vlan_id = untagged vlan id
with no per_sta_vif and no extra tagged vlan.
* vlan_id > 4096 will be used for per_sta_vif and/or tagged vlans.
This way struct wpa_group and drivers API do not need to be changed in
order to implement tagged VLANs or per_sta_vif support.
DYNAMIC_VLAN_* will refer to (struct vlan_description).notempty only,
thus grouping of the stations for per_sta_vif can be used with
DYNAMIC_VLAN_DISABLED, but not with CONFIG_NO_VLAN, as struct
hostapd_vlan is still used to manage AP_VLAN interfaces.
MAX_VLAN_ID will be checked in hostapd_vlan_valid and during setup of
VLAN interfaces and refer to IEEE 802.1q VID. VLAN_ID_WILDCARD will
continue to refer to int vlan_id.
Renaming vlan_id to vlan_desc when type changed from int to struct
vlan_description was avoided when vlan_id was also used in a way that
did not depend on its type (for example, when passed to another
function).
Output of "VLAN ID %d" continues to refer to int vlan_id, while "VLAN
%d" will refer to untagged IEEE 802.1q VID.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This adds a new hostapd configuration parameter
ocsp_stapling_response_multi that can be used similarly to the existing
ocsp_stapling_response, but for the purpose of providing multiple cached
OCSP responses. This commit adds only the configuration parameter, but
does not yet add support for this mechanism with any of the supported
TLS implementations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Expire pending DB request for EAP-SIM/AKA/AKA'. Timeout defaults to 1
second and is user configurable in hostapd.conf (eap_sim_db_timeout).
Signed-off-by: Frederic Leroy <frederic.leroy@b-com.com>
The new hostapd configuration parameter anqp_elem can now be used to
configure arbitrary ANQP-elements for the GAS/ANQP server. In addition
to supporting new elements, this can be used to override previously
supported elements if some special values are needed (mainly for testing
purposes).
The parameter uses following format:
anqp_elem=<InfoID>:<hexdump of payload>
For example, AP Geospatial Location ANQP-element with unknown location:
anqp_elem=265:0000
and AP Civic Location ANQP-element with unknown location:
anqp_elem=266:000000
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Some APs don't include a CSA IE when an ECSA IE is generated,
and mac80211 used to fail following their channel switch. Add
a testing option to hostapd to allow reproducing the behavior.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This fixes an issue where hostapd SET command is used to configure RSN
parameters and the wpa parameter is sent after the other parameters.
Previously, the default case here ended up clearing rsn_pairwise and
wpa_pairwise values and once wpa=2 was finally set, the cipher
configuration had already been lost.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new no_auth_if_seen_on=<ifname> parameter can now be used to
configure hostapd to reject authentication from a station that was seen
on another radio.
This can be used with enabled track_sta_max_num configuration on another
interface controlled by the same hostapd process to reject
authentication attempts from a station that has been detected to be
capable of operating on another band, e.g., to try to reduce likelihood
of the station selecting a 2.4 GHz BSS when the AP operates both a 2.4
GHz and 5 GHz BSS concurrently.
Note: Enabling this can cause connectivity issues and increase latency for
connecting with the AP.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new no_probe_resp_if_seen_on=<ifname> parameter can now be used to
configure hostapd to not reply to group-addressed Probe Request from a
station that was seen on another radio.
This can be used with enabled track_sta_max_num configuration on another
interface controlled by the same hostapd process to restrict Probe
Request frame handling from replying to group-addressed Probe Request
frames from a station that has been detected to be capable of operating
on another band, e.g., to try to reduce likelihood of the station
selecting a 2.4 GHz BSS when the AP operates both a 2.4 GHz and 5 GHz
BSS concurrently.
Note: Enabling this can cause connectivity issues and increase latency
for discovering the AP.
Signed-off-by: Jouni Malinen <j@w1.fi>
hostapd can now be configured to track unconnected stations based on
Probe Request frames seen from them. This can be used, e.g., to detect
dualband capable station before they have associated. Such information
could then be used to provide guidance on which colocated BSS to use in
case of a dualband AP that operates concurrently on multiple bands under
the control of a single hostapd process.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows the new own_ie_override=<hexdump> configuration parameter to
be used to replace the normally generated WPA/RSN IE(s) for testing
purposes in CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <j@w1.fi>
Handling of WPS RF band for 60 GHz was missing. Add it in all relevant
places and also map "AES" as the cipher to GCMP instead of CCMP when
operating on the 60 GHz band.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Update ACS driver offload feature for VHT configuration. In addition,
this allows the chanlist parameter to be used to specify which channels
are included as options for the offloaded ACS case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This change adds the function hostapd_config_clear_wpa_psk() that
deletes an entire wpa_psk structure, making sure to follow the linked
list and to free the allocated memory of each PSK node. This helps to
prevent memory leaks when using PSKs from multiple sources and
reconfiguring the AP during runtime.
Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
The new acs_chan_bias configuration parameter is a space-separated list
of <channel>:<bias> pairs. It can be used to increase (or decrease) the
likelihood of a specific channel to be selected by the ACS algorithm.
The total interference factor for each channel gets multiplied by the
specified bias value before finding the channel with the lowest value.
In other words, values between 0.0 and 1.0 can be used to make a channel
more likely to be picked while values larger than 1.0 make the specified
channel less likely to be picked. This can be used, e.g., to prefer the
commonly used 2.4 GHz band channels 1, 6, and 11 (which is the default
behavior on 2.4 GHz band if no acs_chan_bias parameter is specified).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible to add WPS vendor extensions through the D-Bus
WPSVendorExtensions setter, but these extensions were not freed when the
P2P GO was stopped or when replacing previously configured extensions.
Signed-off-by: Jouni Malinen <j@w1.fi>
These hostapd configuration parameter was left at the default values
(WPA-PSK/TKIP) even for cases where WPA was disabled. While these
parameters are not really used much in non-WPA cases, they do get used
for one corner case in nl80211 configuration to disable encryption of
EAPOL frames in IEEE 802.1X WEP case.
Signed-off-by: Jouni Malinen <j@w1.fi>
hostapd can now be configured to transmit EAP-Initiate/Re-auth-Start
before EAP-Request/Identity to try to initiate ERP. This is disabled by
default and can be enabled with erp_send_reauth_start=1 and optional
erp_reauth_start_domain=<domain>.
Signed-off-by: Jouni Malinen <j@w1.fi>
hostapd was still providing couple of parameters that were used only in
the already removed driver_test.c framework.
Signed-off-by: Jouni Malinen <j@w1.fi>
New kernels in wiphy_suspend() will call cfg80211_leave_all() that will
eventually end up in cfg80211_stop_ap() unless wowlan_triggers were set.
For now, use the parameters from the station mode as-is. It may be
desirable to extend (or constraint) this in the future for specific AP
mode needs.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
The new openssl_cipher configuration parameter can be used to select
which TLS cipher suites are enabled when hostapd is used as an EAP
server with OpenSSL as the TLS library.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use an explicit memset call to clear any hostapd configuration parameter
that contains private information like keys or identity. This brings in
an additional layer of protection by reducing the length of time this
type of private data is kept in memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
The current RADIUS server pointer was updated after each SET command
which broke parsing of multiple RADIUS servers over the control
interface. Fix this by doing the final RADIUS server pointer updates
only once the full configuration is available.
Signed-off-by: Jouni Malinen <j@w1.fi>
clang scan-build does not seem to like the 'd' suffix on floating
constants and ends up reporting analyzer failures. Since this suffix
does not seem to be needed, get rid of it to clear such warnings.
Signed-off-by: Jouni Malinen <j@w1.fi>
p2p_dev_addr was not NULL, so the all zeros case was printed as well.
Clean this up by printing p2p_dev_addr in debug prints only if it is a
real P2P Device Address.
Signed-off-by: Jouni Malinen <j@w1.fi>
