When p2p_cancel is invoked while the GO Negotiation Action TX was
pending, the p2p_send_action_work was not getting cleared.
Signed-off-by: Jithu Jance <jithu@broadcom.com>
The parameter wowlan_triggers is a global string and is not recognised
if it is embraced with double-quotes.
Signed-off-by: Philippe Nunes <philippe.nunes@linux.intel.com>
The PAME-BI bit in the Advertisement Protocol element is reserved for
non-AP STA, so this function will never set that bit to one and as such,
there is not much point in maintaining the placeholder dead code for
this either. (CID 68107)
Signed-off-by: Jouni Malinen <j@w1.fi>
The PSK/passphrase are needed for the control interface events since the
upper layer UI component is required by the specification to be able to
make this available for manual configuration. However, this is not
needed in the INFO verbosity level debug entry, so split the event
generation into two parts.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it easier to change the event message message for indication
when P2P group has stated and removes some duplicated code.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows external programs to use vendor specific information from
P2P peers without wpa_supplicant having to be able to parse and
understand all such vendor specific elements.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds following new control interface commands to allow arbitrary
vendor elements to be added into number of frames:
VENDOR_ELEM_ADD <frame id> <hexdump of elem(s)>
VENDOR_ELEM_GET <frame id>
VENDOR_ELEM_REMOVE <frame id> <hexdump of elem(s)>
VENDOR_ELEM_REMOVE <frame id> *
The following frames are supported in this commit (additional frames can
be added in the future):
0 = Probe Request frame in P2P device discovery
1 = Probe Response frame from P2P Device role
2 = Probe Response frame from P2P GO
3 = Beacon frame from P2P GO
4 = PD Req
5 = PD Resp
6 = GO Neg Req
7 = GO Neg Resp
8 = GO Neg Conf
9 = Invitation Request
10 = Invitation Response
11 = P2P Association Request
12 = P2P Association Response
One or more vendor element can be added/removed with the commands. The
hexdump of the element(s) needs to contain the full element (id, len,
payload) and the buffer needs to pass IE parsing requirements to be
accepted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, offloaded scanning (PNO) on Android was including SSIDs from
all enabled networks regardless of the scan_ssid parameter which
resulted in different behavior for the offloaded case when comparing to
wpa_supplicant initiated scans.
Use the sched_scan match filter to allow broadcast SSID to be used for
scan_ssid=1 networks also with PNO to avoid running active scans for
SSIDs that have not been explicitly marked as requiring an SSID-specific
scan. This reduces exposure of configured network names on the device
when running offloaded scans while the host device is in sleep.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This would not really be needed since these functions check the pointer
above. However, this seems to be too difficult for some static analyzer,
so add the extra check to avoid false reports.
Signed-off-by: Jouni Malinen <j@w1.fi>
This can be used to configure a Hotspot 2.0 Release 2 network externally
for a case where wpa_supplicant-based Interworking network selection is
not used and the update_identifier cannot be copied directly from a
cred.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Incorrect field was used to determine the init=<value> in the regulatory
domain changed control interface event.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new "scan_id=<comma separated list of network ids>" parameter can
now be used to specify a list of network ids that have scan_ssid=1 to
indicate active scanning of the SSID. This adds the listed SSIDs to the
scan command to allow manual scan requests to perform active scans for
hidden SSIDs. For example, "SCAN scan_id=1,7,11" would run a scan with
the SSID fetched from the configured network blocks 1, 7, and 11
(assuming those are set with scan_ssid=1). The SSIDs will be included
even from network blocks that are currently disabled.
The maximum number of SSIDs added to the request is limited by the
driver support. If more than supported values are specified, the command
will fail (returns "FAIL").
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use an explicit memset call to clear any wpa_supplicant configuration
parameter that contains private information like keys or identity. This
brings in an additional layer of protection by reducing the length of
time this type of private data is kept in memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
build_root_nai() will not be extended to write something after the
domain, so there is no need to update the pos pointer after the final
os_snprintf() call in the function. Remove this to make a static
analyzer happier.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is not really necessary check, but it keeps a static analyzer
happier by avoiding dead increment. Doing it this way rather than
removing the increment is less likely to cause problems when new entries
are added here in the future (the "dead" increment would be very much
needed in those cases).
Signed-off-by: Jouni Malinen <j@w1.fi>
The pointer to the current position is enough to figure out whether the
proto string is the first one in the buffer. Removing the separate
tracking variable cleans up a static analyzer warning on dead
assignment.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds an explicit limit for the maximum Wi-Fi Display subelement
length for ASCII hexdump. This would not really be needed since the
buffer is already limited by maximum frame length. Anyway, since this
can make static analyzers happier and the subelement used with this
function is short, we may as well include an explicit check.
Signed-off-by: Jouni Malinen <j@w1.fi>
While the buffer is expected to be large enough for all the IEs, it is
better to check for this explicitly when adding the HS 2.0 Indication
element. (CID 68601)
Signed-off-by: Jouni Malinen <j@w1.fi>
The previously used design was a bit too complex for static analyzers
(e.g., CID 68131, CID 68133) to understand which resulted in false
warnings about uninitialized memory. Avoid this by explicitly
initializing the pointer array to NULL and also skipping any invalid
NULL entry in the helper function.
Signed-off-by: Jouni Malinen <j@w1.fi>
GroupMember is unusable in itself and all the necessary informations are
stored in Peer objects, thus replace the use of GroupMember by Peer.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
If only the Peer is part of one or more group, this property will tell
those via listing their object paths.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This will be useful for a peer to know if it is part of a group either
as a client of our local GO or as the peer GO.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Commit e9852462d5 ('eapol_test: Add PC/SC
reader and PIN command line arguments') did not add break to the switch
statement for the new -R command line option.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Previously, eight character random passphrase was generated
automatically for P2P GO. The new p2p_passphrase_len parameter can be
used to increase this length to generate a stronger passphrase for cases
where practicality of manual configuration of legacy devices is not a
concern.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new command line arguments -R<reader> and -P<PIN> can now be used to
specify which PC/SC reader (prefix match) and PIN are to be used.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to trigger new SA Query procedure to check the state of
the connection immediately after having performed such a check. Limit
the impact of burst of unprotected Deauth/Disassoc frames by starting a
new SA Query procedure only once at least 10 seconds has passed from the
previous SA Query that was triggered by reception of an unprotected
disconnection. The first SA Query procedure for each association does
not follow this rule to avoid issues with test cases that expect to see
an SA Query every time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
"TDLS_TEARDOWN *" can now be used to tear down the direct links to all
TDLS peers. This is useful for debugging purposes.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
If a link is unreachable, the specification mandates we should send a
teardown packet via the AP with a specific teardown reason. Force this
by first disabling the link and only then sending the teardown packet
for the LOW_ACK event.
Rename the TDLS LOW_ACK event handler to better reflect its purpose.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
This removes number of unnecessary #ifdef CONFIG_P2P blocks from generic
code by hiding the conditional build into p2p_supplicant.h with empty
inline functions.
Signed-off-by: Jouni Malinen <j@w1.fi>
Performing a P2P Device flow such as p2p_listen or
p2p_find, can degrade the performance of an active interface
connection, if the listen frequency is different than the
frequency used by that interface.
To reduce the effect of P2P Device flows on other interfaces,
try changing the listen channel of the P2P Device to match the
operating channel of one of the other active interfaces. This change
will be possible only in case that the listen channel is not forced
externally, and will be delayed to a point where the P2P Device
state machine is idle.
The optimization can be configured in the configuration file and
is disabled by default.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
In case there is no preference for the GO operating channel,
try using one of 1, 6, 11 (randomly), and only if the random
selection is not suitable traverse all the channels 1..11.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Remove the seperation between getting the local interface frequency and
other interfaces frequencies since going over all the radio interfaces
includes the local interface.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
When the number of frequencies supported by the kernel is bigger than
one, and there is a need to pick a frequency for a new flow such as P2P
GO Negotiation or P2P Invitation, the flow should be able to pick the
best frequency among all the frequencies currently used by the device.
In order to prioritize between the currently used frequencies, add
the ability to collect additional data about each used frequency
(if the frequency is used by a station interface or P2P Client)
and when needed select the best frequency, where:
1. Infrastructure interfaces have highest priority
2. P2P Client interfaces have higher priority over AP/GO
interfaces.
The rational is that the frequency of an AP/GO can change while
that of a station interface cannot.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Remove the check for get_radio_name support from
get_shared_radio_freqs_data() since get_radio_name is no longer in use
in this function.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Most of these calls are checked to return success and there is no reason
why these wouldn't, so be more consistent. This addresses CID 62841,
CID 62840, CID 62839, CID 62838, CID 62837, CID 62836.
Signed-off-by: Jouni Malinen <j@w1.fi>
If this chmod() call fails, the global control interface is allowed to
be used since there was no change to its group. Anyway, it can be
helpful to note the error case in debug log instead of silently ignoring
it.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit b125c48fce ('P2P: Add wfd_dev_info=
field for device found event') added Wi-Fi Display device info to the
P2P-DEVICE-FOUND events. However, it did not include proper bounds
checking in wifi_display_subelem_hex() and could accept subelements with
invalid length field values. This could result in buffer read overflow
of up to 64 kB and inclusion of heap memory in the local control
interface event and/or process crash due to invalid memory access. Fix
this by checking the validity of the length field before writing a
hexdump of the data.
Signed-off-by: Jouni Malinen <j@w1.fi>
The vendor_ext[i] = NULL setting did not make any sense since
num_vendor_ext should have been used to index the vendor_ext array. The
old code did not do any harm since i >= num_vendor_ext and none of the
already set entries could have been cleared. Anyway, better clean this
by making it skip the setting to NULL similarly to what was already done
in the P2P peer vendor ext getter.
Signed-off-by: Jouni Malinen <j@w1.fi>
The OSEN code path hardcodes number of struct wpa_ie_data items.
However, it did not clear the full structure and some uninitialized
fields could have been used (e.g., ie.mgmt_group_cipher for a debug
print and ie.capabilities for checking MFPC). Fix this by clearing the
ie data before filling in the hardcoded OSEN values.
Signed-off-by: Jouni Malinen <j@w1.fi>
The Action code field is in a fixed location, so the IEEE80211_HDRLEN
can be used here to clean up bounds checking to avoid false reports from
static analyzer.
Signed-off-by: Jouni Malinen <j@w1.fi>
The Action code field is in a fixed location, so the IEEE80211_HDRLEN
can be used here to clean up bounds checking to avoid false reports from
static analyzer.
Signed-off-by: Jouni Malinen <j@w1.fi>
