In cases where the bandwidth is not set when starting an AP/P2P GO,
the code tries to use 160 MHz or 80 MHz channels. As a result, the
AP/P2P GO configuration is set to use these channel widths even if
they are not available, which may results in failing to start the
AP/P2P GO.
Fix this by changing the AP/P2P GO configuration not to use VHT channels
when they are not available. In this case the AP/P2P GO will use a 40
MHz channel, if available, or a 20 MHz channel, if this is the maximum
available width.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Since hostapd supports ACS now, let's enable its support in
wpa_supplicant as well when starting AP mode.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
[u.oelmann@pengutronix.de: rebased series from hostap_2_1~944 to master]
[u.oelmann@pengutronix.de: adjusted added text in defconfig]
Signed-off-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
The new max_oper_chwidth and freq2 arguments to P2P_CONNECT, P2P_INVITE,
and P2P_GROUP_ADD control interface commands can be used to request
larger VHT operating channel bandwidth to be used than the previously
used maximum 80 MHz.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
CTWindow was set for all AP interfaces if the driver supports it and
this parameter is set in wpa_supplicant configuration. This results in
failing to start an AP that is not a P2P GO as this setting is rejected
by the driver.
Fix that by setting the CTWindow only for P2P GO interface.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Use channel switch mechanism to move a P2P GO to a new channel,
when required. In order to be able to reconfigure the GO channel,
split wpa_supplicant_conf_ap() function, so the frequency
configuration part can be reused to find additional CSA settings.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Fix a bug in wpas_ap_ch_switch() function, which didn't pass VHT
frequencies correctly to hostapd_event_ch_switch().
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This new mechanism can be used to combine multiple periodic AP
(including P2P GO) task into a single eloop timeout to minimize number
of wakeups for the process. hostapd gets its own periodic caller and
wpa_supplicant uses the previously added timer to trigger these calls.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Do not allow 40 MHz co-ex PRI/SEC switch to force us to change our PRI
channel if we have an existing connection on the selected PRI channel
since doing multi-channel concurrency is likely to cause more harm than
using different PRI/SEC selection in environment with multiple BSSes on
these two channels with mixed 20 MHz or PRI channel selection.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the RX frequency of the Probe Request frame is known, specify it when
sending the Probe Response frame. This is needed when the Probe Request
frame is received on another virtual interface, for example, when a GO
or P2PS client are discoverable on the group operating channel.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
In some cases, Probe Request frames can be received by a peer not only
on a listen channel. In this case an additional rx_freq parameter
explitly contains a Probe Request frame RX frequency. In case rx_freq is
set to 0, a Probe Request frame RX channel is assumed to be our own
listen channel (p2p->cfg->channel).
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
This makes the AP mode more consistent with other modes by providing a
matching pair of CTRL-EVENT-CONNECTED and CTRL-EVENT-DISCONNECTED event
messages.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add radar event processing logic for AP/P2P GO. The DFS processing
functions from hostapd are now used for these wpa_supplicant cases as
well for both offloaded and non-offloaded DFS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Read p2p_go_ctwindow (0-127 TUs) from the config file, and pass it to
the driver on GO start.
Use p2p_go_ctwindow=0 (no CTWindow) by default.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Publish support for Tx STBC in the HT capabilities of a GO and AP
controlled by wpa_supplicant in case the hardware supports it.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
This is more of a theoretical case since this part is done only during
setup and the structure is not allocated in practice. Anyway,
maintaining more consistent use of bin_clear_free() for structures that
may contain keys is useful.
Signed-off-by: Jouni Malinen <j@w1.fi>
Since mesh functionality uses struct hostapd_data to maintain peer
state, the existing STA* control interface commands can be used to
display information about the peers.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a new option "mesh_ht_mode" that specifies the HT mode for the
mesh, with this option on, mesh beacons, actions frames, and probe
responses with include the appropriate HT information elements.
[original implementation by Chun-Yeow Yeoh <yeohchunyeow@gmail.com>]
[some fixes by Masashi Honma <masashi.honma@gmail.com>]
Signed-off-by: Ashok Nagarajan <ashok.dragon@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Add smps_modes field, and let the driver fill it with its supported SMPS
modes (static/dynamic). This will let us start an AP with specific SMPS
mode (e.g., dynamic) that will allow it to reduce its power usage.
Signed-off-by: Eliad Peller <eliad@wizery.com>
The new ext_eapol_frame_io parameter can be used to configure hostapd
and wpa_supplicant to use control interface for receiving and
transmitting EAPOL frames. This makes it easier to implement automated
test cases for protocol testing. This functionality is included only in
CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use hostapd_freq_params instead of simple frequency parameter for driver
commands. This is preparation for IBSS configuration to allow use of
HT/VHT in IBSS.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
This removes number of unnecessary #ifdef CONFIG_P2P blocks from generic
code by hiding the conditional build into p2p_supplicant.h with empty
inline functions.
Signed-off-by: Jouni Malinen <j@w1.fi>
The Action code field is in a fixed location, so the IEEE80211_HDRLEN
can be used here to clean up bounds checking to avoid false reports from
static analyzer.
Signed-off-by: Jouni Malinen <j@w1.fi>
The Action code field is in a fixed location, so the IEEE80211_HDRLEN
can be used here to clean up bounds checking to avoid false reports from
static analyzer.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is not much point in building devices with WPS 1.0 only supported
nowadays. As such, there is not sufficient justification for maintaining
extra complexity for the CONFIG_WPS2 build option either. Remove this by
enabling WSC 2.0 support unconditionally.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The ieee80211w parameter was not previously copied to the hostapd BSS
structure from wpa_supplicant configuration, so PMF was practically
disabled. Allow it to be configured through the wpa_supplicant network
configuration block.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit adds an option to optimize AP teardown by leaving the
deletion of keys (including group keys) and stations to the driver.
This optimization option should be used if the driver supports stations
and keys removal when stopping an AP.
For example, the optimization option will always be used for cfg80211
drivers since cfg80211 shall always remove stations and keys when
stopping an AP (in order to support cases where the AP is disabled
without the knowledge of wpa_supplicant/hostapd).
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Since P2P specification mandates P2P GO to support WMM-PS with legacy
STAs, enable this automatically if the driver indicates support for
U-APSD in AP mode. The "P2P_SET go_apsd 0" command can still be used to
disable this if needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant_create_ap() is only called for AP mode, so there is no
point in trying to address station (infra/IBSS) modes.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This new mechanism allows P2P Client to request an IPv4 address from the
GO as part of the 4-way handshake to avoid use of DHCP exchange after
4-way handshake. If the new mechanism is used, the assigned IP address
is shown in the P2P-GROUP-STARTED event on the client side with
following new parameters: ip_addr, ip_mask, go_ip_addr. The assigned IP
address is included in the AP-STA-CONNECTED event on the GO side as a
new ip_addr parameter. The IP address is valid for the duration of the
association.
The IP address pool for this new mechanism is configured as global
wpa_supplicant configuration file parameters ip_addr_go, ip_addr_mask,
ip_addr_star, ip_addr_end. For example:
ip_addr_go=192.168.42.1
ip_addr_mask=255.255.255.0
ip_addr_start=192.168.42.2
ip_addr_end=192.168.42.100
DHCP mechanism is expected to be enabled at the same time to support P2P
Devices that do not use the new mechanism. The easiest way of managing
the IP addresses is by splitting the IP address range into two parts and
assign a separate range for wpa_supplicant and DHCP server.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"NFC_REPORT_HANDOVER {INIT,RESP} P2P <req> <sel>" can now be used to
report completed NFC negotiated connection handover in which the P2P
alternative carrier was selected.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
New functionality is needed for this with the update NFC connection
handover design that depends on the AP side using the public key hash
from the handover request.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When GAS is used with PMF negotiated, Protected Dual of Public Action
frames are expected to be used instead of Public Action frames, i.e.,
the GAS/ANQP frames are expected to be encrypted. Add support for this
different category of Action frames being used for GAS. The payload
after the Category field is identical, so the only change is in using
the Category field based on what was received in the request frames. For
backwards compatibility, do not enforce protected dual to be used on the
AP side, i.e., follow what the station does.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A TX status event could be received after the AP interface has already
been deinitialized. This needs to check for NULL pointer before trying
to indicate the event to AP functions.
Signed-hostap: Jouni Malinen <j@w1.fi>
WPA_CIPHER_* and CIPHER_* are used for the exact same set of cipher
suites with the main difference being that the WPA_CIPHER_* version is
suitable to be used as a bitfield. Similarly, WPA_KEY_MGMT_* and
KEY_MGMT_* have similar design for AKMs. There is no need to maintain
two separate copies of the definitions since the bitfield compatible
version can be used for both needs. Get rid of the CIPHER_* and
KEY_MGMT_* versions to clean up the implementation by getting rid of
unnecessary mapping functions.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds initial parts for supporting the new GCMP-256, CCMP-256,
BIP-GMAC-128, BIP-GMAC-256, and BIP-CMAC-256 cipher suites.
Signed-hostap: Jouni Malinen <j@w1.fi>
Adds support for VHT by parsing bandwidth and center_freq{1,2}.
Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Add chan_switch to the control interface of wpa_supplicant and hostapd,
and also to wpa_cli and hostapd_cli.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Build CSA settings and call the driver to perform the switch. Construct
Beacon, Probe Response, and (Re)Association Response frames both for CSA
period and for the new channel. These frames are built based on the
current configuration. Add CSA IE in Beacon and Probe Response frames.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This makes it more convenient to move BSS configuration entries between
struct hostapd_config instances to clean up per-BSS configuration file
design.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit ca9bc5b566 added wpas_conf_ap_vht()
as a static function with the caller within CONFIG_IEEE80211N, but the
function outside. This resulted in a compiler warning for wpa_supplicant
AP/P2P builds when CONFIG_IEEE80211N=y was not used. Fix that by using
matching conditional block around the function.
Signed-hostap: Jouni Malinen <j@w1.fi>
Start GO with VHT support if VHT option was requested
and the appropriate channels are available.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
wpa_supplicant crashes if driver configuration for AP mode interface
configuration fails after group negotiation. This is because of a
regression from commit 1075b29571 that
ends up freeing the wpa_s instance from within
wpa_supplicant_create_ap() without the caller knowing.
Fix this by using an eloop timeout to free remove the P2P group so that
wpa_supplicant_create_ap() and especially wpa_supplicant_associate()
callers do not need to know about interface getting possibly removed. In
addition, move the P2P specific code into p2p_supplicant.c where it
really belongs. This allows the already existing group formation timeout
to be used by reducing the timeout to zero.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
