This patch add functionality of mesh SAE PMKSA caching. If the local STA
already has peer's PMKSA entry in the cache, skip SAE authentication and
start AMPE with the cached value.
If the peer does not support PMKSA caching or does not have the local
STA's PMKSA entry in the cache, AMPE will fail and the PMKSA cache entry
of the peer will be removed. Then STA retries with ordinary SAE
authentication.
If the peer does not support PMKSA caching and the local STA uses
no_auto_peer=1, the local STA can not retry SAE authentication because
NEW_PEER_CANDIDATE event cannot start SAE authentication when
no_auto_peer=1. So this patch extends MESH_PEER_ADD command to use
duration(sec). Throughout the duration, the local STA can start SAE
authentication triggered by NEW_PEER_CANDIDATE even though
no_auto_peer=1.
This commit requires commit 70c93963ed
('SAE: Fix PMKID calculation for PMKSA cache'). Without that commit,
chosen PMK comparison will fail.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This allows a mesh peer connection to be initiated manually in
no_auto_peer mesh networks.
Signed-off-by: Natsuki Itaya <Natsuki.Itaya@jp.sony.com>
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This command allows the specified mesh peer to be disconnected.
Signed-off-by: Natsuki Itaya <Natsuki.Itaya@jp.sony.com>
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
The full VHT channel information was not set in the hostapd data
structures which resulted in incorrect information (all zeros) being
used when building the VHT Operation element for peering messages while
the actual driver mode was set with the full details. We did not seem to
use the VHT information from peering messages, so this does not change
behavior with another wpa_supplicant-based mesh implementation. Anyway,
these elements should match the ones used in Beacon frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed to avoid hitting WEP/TKIP detection in
ibss_mesh_setup_freq() if the previous connection used WEP or TKIP.
Previously, that could have resulted in VHT and HT getting disabled for
the mesh connection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Mesh Points themselves have capability to support VHT as long as
hardware supports it. However, supporting VHT in mesh mode was disabled
because no one had clearly tested and confirmed its functionality. Since
VHT80 has now been verified to work with ath10k QCA988X driver and
mac80211_hwsim, enable VHT support in mesh mode.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
The mesh SAE auth often fails with master branch. By bisect I found
commit eb5fee0bf5 ('SAE: Add side-channel
protection to PWE derivation with ECC') causes this issue. This does not
mean the commit has a bug. This is just a CPU resource issue.
After the commit, sae_derive_pwe_ecc() spends 101(msec) on my PC (Intel
Atom N270 1.6GHz). But dot11RSNASAERetransPeriod is 40(msec). So
auth_sae_retransmit_timer() is always called and it can causes
continuous frame exchanges. Before the commit, it was 23(msec).
On the IEEE 802.11 spec, the default value of dot11RSNASAERetransPeriod
is defined as 40(msec). But it looks short because generally mesh
functionality will be used on low spec devices. Indeed Raspberry Pi B+
(ARM ARM1176JZF-S 700MHz) requires 287(msec) for new
sae_derive_pwe_ecc().
So this patch makes the default to 1000(msec) and makes it configurable.
This issue does not occur on infrastructure SAE because the
dot11RSNASAERetransPeriod is not used on it.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Should there not be enough room in the output buffer, the
bss_basic_rate_set line would not be printed. This error case was
handled otherwise, but the temporary memory allocation for building the
information was not freed.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible to leave the driver in mesh point state if upper layer
mesh initialization failed in wpa_supplicant_mesh_init(). With nl80211,
this results in the vif being left in mesh point mode instead of
restoring it to station mode. That seems to break normal functionality,
e.g., for Public Action frame TX/RX. Fix this by restoring station mode
on mesh failure path.
This error could be triggered, e.g., with the following hwsim test case
sequence: wpas_mesh_secure_sae_missing_password
nfc_p2p_static_handover_tagdev_go_forced_freq
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant_deinit_iface() ends up removing all P2P groups if the
removed interface is the parent interface. This is correct behavior in
general, but this resulted in issues in the new group interface
initialization error path since wpa_s->parent was not assigned before
hitting this check. Fix this by assigning wpa_s->parent as part of
wpa_supplicant_add_iface().
Signed-off-by: Jouni Malinen <j@w1.fi>
Current mesh code uses ap_max_inactivity as inactivity timer. This patch
makes it configurable.
There is another mesh inactivity timer in mac80211. The timer works even
if user_mpm=1. So this patch sets the max value to the timer for
workaround.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Automatically enable HT20, HT40+, HT40-, or VHT, based on driver
capabilities. This obsoletes the mesh_ht_mode network block parameter
that was previously used to configure HT parameters.
Signed-off-by: Jouni Malinen <j@w1.fi>
Maximum number of peer links is maximum number of connecting mesh peers
at the same time. This value is 0..255 based on the
dot11MeshNumberOfPeerings range.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
The mesh gate is used to bridge (or route) between mesh network and
another network. For example, mesh gate acts as router between mesh
network and IEEE 802.11 BSS network.
This command makes a virtual mesh interface to be used for mesh gate.
This command expects to be used like this.
wpa_cli -i wlan0 MESH_INTERFACE_ADD ifname=mesh0
wpa_cli -i mesh0 add_network
wpa_cli -i mesh0 set_network 0 ssid '"commell_2X_mmm"'
wpa_cli -i mesh0 set_network 0 mode 5
wpa_cli -i mesh0 set_network 0 frequency 2412
wpa_cli -i mesh0 set_network 0 key_mgmt SAE
wpa_cli -i mesh0 set_network 0 psk '"01234567"'
wpa_cli -i mesh0 mesh_group_add 0
wpa_cli -i wlan0 mesh_group_remove mesh0
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This is needed to allow proper Action frame transmission to work without
having to claim these to be offchannel operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This patch makes four MIB variables for plink configurable and sets the
correct default values based on IEEE Std 802.11s-2011.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Android 4.4 uses "BSS" command instead of "SCAN_RESULT" command.
So this patch add the mesh scan result for BSS command.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
STAs that have different BSSBasicRateSet cannot connect to each other
as per IEEE 802.11s-2011 9.6.0c1:
"A mesh STA shall not establish a mesh peering with a mesh STA using a
different BSSBasicRateSet."
Make BSSBasicRateSet configurable to improve interoperability with other
stations.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Add a new option "mesh_ht_mode" that specifies the HT mode for the
mesh, with this option on, mesh beacons, actions frames, and probe
responses with include the appropriate HT information elements.
[original implementation by Chun-Yeow Yeoh <yeohchunyeow@gmail.com>]
[some fixes by Masashi Honma <masashi.honma@gmail.com>]
Signed-off-by: Ashok Nagarajan <ashok.dragon@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Add timer to do SAE re-authentication with number of tries defined
by MESH_AUTH_RETRY and timeout defined by MESH_AUTH_TIMEOUT.
Ignoring the sending of reply message on "SAE confirm before commit"
to avoid "ping-pong" issues with other mesh nodes. This is obvious when
number of mesh nodes in MBSS reaching 6.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
When mesh is configured in, include the wildcard mesh id so that mesh
networks are returned.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Abele <jason.abele@gmail.com>
The mesh peering manager establishes and maintains links among
mesh peers, tracking each peer link via a finite state machine.
This implementation supports open mesh peerings.
[assorted fixes from Yu Niiro <yu.niiro@gmail.com>]
[more fixes from Masashi Honma <masashi.honma@gmail.com>]
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Ashok Nagarajan <ashok.dragon@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-hostap: Bob Copeland <me@bobcopeland.com>
Add routines to (de)initialize mesh interface data structures and
join and leave mesh networks.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
