While the most likely production use case for DPP push button is to
provision the AP's current configuration, there might be some use cases
for providing different configuration. Add possibility for doing this by
extending the DPP_PUSH_BUTTON command to accept an optional set of
parameters similarly to the other DPP commands for the Configurator.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Allow the Responder/Initiator hash values to be corrupted in Push Button
Presence Announcement messages for testing purposes.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add support to use a push button -based bootstrap mechanism with DPP.
The new DPP_PUSH_BUTTON control interface command enables this mode on
the AP/hostapd and station/wpa_supplicant. This goes through the
following sequence of events: a suitable peer in active push button mode
is discovered with session overlap detection, PKEX is executed with
bootstrap key hash validation, DPP authentication and configuration
exchanges are performed.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add feature capability indication for P802.11az security for the drivers
to advertise capabilities such as secure LTF support, secure RTT
measurement exchange support, and protection of range negotiation and
measurement management frames for station and AP interfaces
independently. This allows a more fine-tuned capability indication as an
alternative to the upstream nl80211 mechanism that is not specific to
the operating mode.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add vendor command QCA_NL80211_VENDOR_SUBCMD_COAP_OFFLOAD to
enable/disable offload processing in firmware for CoAP messages
(RFC7252: The Constrained Application Protocol) or fetch the
CoAP messages cached during offload processing.
Signed-off-by: Yu Wang <quic_yyuwang@quicinc.com>
Add the following two vendor attributes to send TIM beacon
statistics to userspace which can be used for power saving:
QCA_WLAN_VENDOR_ATTR_LL_STATS_TIM_BEACON
QCA_WLAN_VENDOR_ATTR_LL_STATS_TIM_BEACON_ERR
Signed-off-by: Jingxiang Ge <quic_jge@quicinc.com>
Define QCA vendor interface for PASN offload to userspace from the driver.
The driver can send this command as an event to a userspace component to
perform PASN authentication with a list of peers with which the driver
needs to do ranging. The userspace component, if capable of performing
PASN handshake, can perform PASN handshake with all the peer devices and
set the relevant keys by sending the
QCA_NL80211_VENDOR_SUBCMD_SECURE_RANGING_CONTEXT command for each peer
to the driver.
Once PASN handshake is completed with all requested peers, the userspace
component sends consolidated status for all the peers to the driver. The
consolidated report is required for the driver to understand that the
PASN handshake process is complete and whether it succeeded/failed for
each of the peers it was requested for. The secure ranging context is
configured only for the peers with which the PASN handshake succeeded.
When the driver requests PASN keys, the userspace component can set the
keys from its cache if those keys have not already expired and were
derived with the same source MAC address that is requested by the driver
instead of doing the full PASN handshake again.
If the driver detects that current keys of a peer are not valid anymore,
it sends a notification to userspace using the
QCA_NL80211_VENDOR_SUBCMD_PASN command and setting the action to
QCA_WLAN_VENDOR_PASN_ACTION_DELETE_SECURE_RANGING_CONTEXT. The userspace
component should delete the corresponding keys from its cache.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a new QCA vendor attribute
QCA_WLAN_VENDOR_ATTR_CONCURRENT_POLICY_AP_CONFIG to
QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_POLICY sub command to set the
concurrency policy for AP interface.
QCA_WLAN_VENDOR_ATTR_CONCURRENT_POLICY_AP_CONFIG uses the values
defined in enum qca_wlan_concurrent_ap_policy_config to specify
concurrency policy.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
Rename QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_MULTI_STA_POLICY to
QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_POLICY to allow extension for other
interface type(s). A subsequent commit will extend the renamed
definitions in a manner that is inconsistent with the current naming.
This is a precursor for AP/P2P concurrency policy configuration support
via updated vendor command QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_POLICY.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
Move most of CHANWIDTH_* definitions from ieee80211_defs.h to defs.h as
the definitions are getting used mostly for internal purpose only. Also
change prefix of the definitions to CONF_OPER_CHWIDTH_* and update in
all the files accordingly.
Leave the couple of VHT-specific exceptions to use the old defines (the
reason why they were originally added as VHT values), to avoid use of
clearly marked configuration values in information elements. In
addition, use the defines instead of magic values where appropriate.
Signed-off-by: Aleti Nageshwar Reddy <quic_anageshw@quicinc.com>
This started failing with the OCV implementation change to ignore the
second segment when using a 160 MHz channel.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Try to avoid an exception while processing an exception that indicates
the test case failed. Explicit DISCONNECT command here can avoid the
undesired FAIL-BUSY from cleanup SCAN.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add QCA vendor event to indicate user space that the driver recovery is
completed after the internal failure reported with
QCA_NL80211_VENDOR_SUBCMD_HANG.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
For hidden GBK encoding of a Chinese SSID, both the UTF-8 and GBK
encoding profiles are added into wpa_supplicant to make sure the
connection succeeds. In this situation, wpa_supplicant_select_network()
will not be called so current_ssid is NULL when association begins.
Android monitors the WPA_EVENT_STATE_CHANGE event to get the SSID and
BSSID. When connecting to a Chinese SSID, in case of association
rejection happens, Android will report null SSID to OEM APP because
current_ssid is updated after wpa_supplicant_set_state(wpa_s,
WPA_ASSOCIATING), which may cause confusion.
Fix this by setting the current_ssid before changing state to
ASSOCIATING.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a new QCA vendor attribute
QCA_WLAN_VENDOR_ATTR_CONFIG_AUDIO_DATA_PATH to
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION to configure audio data
path.
Possible audio data paths are defined in enum qca_wlan_audio_data_path.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
Vendor command to get the WLAN radio combinations matrix supported by
the device which provides the device simultaneous radio configurations
such as standalone, dual band simultaneous, and single band
simultaneous.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The initial OCV implementation validating this field in the OCI element
for both the 80+80 MHz and 160 MHz cases. However, IEEE Std 802.11-2020,
12.2.9 ("Requirements for Operating Channel Validation") limitis that
verification step for the 80+80 MHz case: "Verifying that, if operating
an 80+80 MHz operating class, the frequency segment 1 channel number ...
is equal to the Frequency Segment 1 Channel Number field of the OCI."
Remove this check for the 160 MHz case since there has been incorrect
interpretation on how the Frequency Segment 1 Channel Number field of
the OCI element is set in this case (using VHT rules for CCFS2). The
modified validation step is meets the real need here, is compliant with
the standard, and avoids potential interoperability issues when using
contiguous 160 MHz channels.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Previously, the driver could optionally (using QCA vendor command)
provide a preferred channel list to wpa_supplicant for channel selection
during the GO negotiation. Channel selection process can be more
efficient with the information of weights and flags of the preferred
channel list that can be provided by the driver. Use a weighted
preferred channel list provided by the driver for channel selection
during GO negotiation if such a list is available.
Signed-off-by: Sreeramya Soratkal <quic_ssramya@quicinc.com>
Add QCA_ATTR_ROAM_CONTROL_RX_LINKSPEED_THRESHOLD value as the RX link
speed threshold to disable roaming. If the current link speed is above
the threshold, there is no need to roam.
Signed-off-by: Jianmin Zhu <quic_jianminz@quicinc.com>
Add a new QCA vendor attribute
QCA_WLAN_VENDOR_ATTR_ACS_LAST_SCAN_AGEOUT_TIME to
QCA_NL80211_VENDOR_SUBCMD_DO_ACS and opportunistically optimize time
taken for ACS scan. Avoid scanning the channels which were scanned
within last QCA_WLAN_VENDOR_ATTR_ACS_LAST_SCAN_AGEOUT_TIME milliseconds
and use scan results from the scan results cache for ACS scoring. For
other channels, perform ACS scan and use the received scan results.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
When 6 GHz channels are included in channel list of P2P Action frames
but some peer devices don't support the 6 GHz feature and cannot parse
P2P IE data correctly, P2P handshake will fail.
Remove 6 GHz channels from the P2P Action frames if the peer doesn't
support 6 GHz feature to avoid such failures.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
A few of the comments in the QCA vendor commands have a space
character before a tab. That is pointless, and some code style
checkers may complain about it, so remove the spaces.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Skip the x_snoop_deinit() operations if hostapd did not actually
configure the parameters in the first place. While clearing these
specific parameters is unlikely to change how they were set outside the
scope of hostapd, it is better to leave them as-is to avoid surprises if
hostapd was not configured to use ProxyARP.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Get rid of the gcc warnings on potentially truncating the output buffer
by explicitly checking that there was enough room to write the full
string.
Signed-off-by: Jouni Malinen <j@w1.fi>
The initialization values used for the FIPS 186-2 PRF are identical to
the ones used in SHA1Init(), so use that internal function instead of
maintaining a duplicate set of values here. fips186_2_prf() was already
using an internal SHA1Transform() function so using another internal
function does not make this any worse.
Signed-off-by: Jouni Malinen <j@w1.fi>
OpenSSL 3.0 has deprecated the low-level SHA1 functions and does not
include an upper layer interface that could be used to use the
SHA1_Transform() function. Use the internal SHA-1 implementation instead
as a workaround.
While this type of duplicate implementation of SHA-1 is not really
ideal, this PRF is needed only for EAP-SIM/AKA and there does not seem
to be sufficient justification to try to get this working more cleanly
with OpenSSL 3.0.
Signed-off-by: Jouni Malinen <j@w1.fi>
The EVP_MAC context data needs to be freed on error paths.
Fixes: e31500adea ("OpenSSL: Implement HMAC using the EVP_MAC API")
Signed-off-by: Jouni Malinen <j@w1.fi>
The conversion to the new OpenSSL 3.0 API had forgotten to free the
context structure.
Fixes: bcd299b326 ("OpenSSL: Convert DH/DSA parameter loading to new API")
Signed-off-by: Jouni Malinen <j@w1.fi>
Extend IMSI privacy functionality to allow an attribute (in name=value
format) to be added using the new imsi_privacy_attr parameter.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This can be used to make sure wpa_supplicant does not process DPP
messages sent in Public Action frames when a test setup is targeting
DPP-over-TCP.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Use imsi_privacy_cert as the name of the configuration parameter for the
X.509v3 certificate that contains the RSA public key needed for IMSI
privacy. The only allowed format for this information is a PEM-encoded
X.509 certificate, so the previous name was somewhat confusing.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is an allocated resource so it needs to be free on the error path.
Fixes: 42871a5d25 ("EAP-SIM/AKA peer: IMSI privacy")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Disable a network profile that has set the imsi_privacy_key if a valid
key cannot be read from the specified file. Previously, this check was
done only after having associated, but there is no point in associating
just to see EAP authentication fail in such a case. This is needed for
avoiding connection attempts if the X.509 certificate for IMSI privacy
has expired.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
