Add more details into configuration comments and a runtime info message
if ap_scan=2 is used with the nl80211 driver interface.
Signed-off-by: Jouni Malinen <j@w1.fi>
Upon any change in the currently used channels evaluate if a GO should
move to a different operating frequency, where the possible scenarios:
1. The frequency that the GO is currently using is no longer valid,
due to regulatory reasons, and thus the GO must be moved to some
other frequency.
2. Due to Multi Concurrent Channel (MCC) policy considerations, it would
be preferable, based on configuration settings, to prefer Same
Channel Mode (SCM) over concurrent operation in multiple channels.
The supported policies:
- prefer SCM: prefer moving the GO to a frequency used by some other
interface.
- prefer SCM if Peer supports: prefer moving the GO to a frequency
used by some other station interface iff the other station
interface is using a frequency that is common between the local and
the peer device (based on the GO Negotiation/Invitation signaling).
- Stay on the current frequency.
Currently, the GO transition to another frequency is handled by a
complete tear down and re-setup of the GO. Still need to add CSA flow to
the considerations.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The mesh SAE auth often fails with master branch. By bisect I found
commit eb5fee0bf5 ('SAE: Add side-channel
protection to PWE derivation with ECC') causes this issue. This does not
mean the commit has a bug. This is just a CPU resource issue.
After the commit, sae_derive_pwe_ecc() spends 101(msec) on my PC (Intel
Atom N270 1.6GHz). But dot11RSNASAERetransPeriod is 40(msec). So
auth_sae_retransmit_timer() is always called and it can causes
continuous frame exchanges. Before the commit, it was 23(msec).
On the IEEE 802.11 spec, the default value of dot11RSNASAERetransPeriod
is defined as 40(msec). But it looks short because generally mesh
functionality will be used on low spec devices. Indeed Raspberry Pi B+
(ARM ARM1176JZF-S 700MHz) requires 287(msec) for new
sae_derive_pwe_ecc().
So this patch makes the default to 1000(msec) and makes it configurable.
This issue does not occur on infrastructure SAE because the
dot11RSNASAERetransPeriod is not used on it.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
1. Add global p2p_cli_probe property to enable/disable Probe Request
frame RX reporting for connected P2P Clients. The property can be set to
0 - disable or 1 - enable. The default value is 0.
2. Enable Probe Request frame RX reporting for P2P Client on
WPA_COMPLETED state if p2p_cli_probe property is set to 1. Disable it
when an interface state is changing to any other state.
3. Don't cancel Probe Request frame RX reporting on wpa_stop_listen for
a connected P2P Client handling Probe Request frames.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
This commit adds a configurable parameter (wps_priority) to specify the
priority for the networks derived through WPS connection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes source code more consistent. The use within Android driver
interface is left as-is to avoid changes in the old PNO interface
definition.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Read p2p_go_ctwindow (0-127 TUs) from the config file, and pass it to
the driver on GO start.
Use p2p_go_ctwindow=0 (no CTWindow) by default.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
The new reassoc_same_bss_optim=1 configuration parameter can now be used
to request wpa_supplicant to bypass the unnecessary Authentication frame
exchange when reassociating back to the same BSS with which the device
is already associated. This functionality is disabled by default since
it may cause undesired interoperability issues with some APs.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new "DUMP" and "SET <variable>" control interface commands can be
used to fetch global wpa_supplicant configuration parameters.
Signed-off-by: Ola Olsson <ola.olsson@sonymobile.com>
This new wpa_supplicant configuration parameter can be used to force
passive scanning to be used for most scanning cases at the cost of
increased latency and less reliably scans. This may be of use for both
testing purposes and somewhat increased privacy due to no Probe Request
frames with fixed MAC address being sent out.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Current mesh code uses ap_max_inactivity as inactivity timer. This patch
makes it configurable.
There is another mesh inactivity timer in mac80211. The timer works even
if user_mpm=1. So this patch sets the max value to the timer for
workaround.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This makes it easier for upper layer applications to get information
regarding the server certificate without having to use a special
certificate probing connection. This provides both the SHA256 hash of
the certificate (to be used with ca_cert="hash://server/sha256/<hash>",
if desired) and the full DER encoded X.509 certificate so that upper
layer applications can parse and display the certificate easily or
extract fields from it for purposes like configuring an altsubject_match
or domain_suffix_match.
The old behavior can be configured by adding cert_in_cb=0 to
wpa_supplicant configuration file.
Signed-off-by: Jouni Malinen <j@w1.fi>
Maximum number of peer links is maximum number of connecting mesh peers
at the same time. This value is 0..255 based on the
dot11MeshNumberOfPeerings range.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Add user_mpm config parameter, when this is set to 1 (the default) the
peer link management is done on userspace, otherwise the peer management
will be done by the kernel.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
This commit introduces a QCA vendor command and event to provide an
option to use extended versions of the nl80211 connect/roam operations
in a way that allows drivers to offload key management operations to the
driver/firmware.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new openssl_cipher configuration parameter can be used to select
which TLS cipher suites are enabled for TLS-based EAP methods when
OpenSSL is used as the TLS library. This parameter can be used both as a
global parameter to set the default for all network blocks and as a
network block parameter to override the default for each network
profile.
Signed-off-by: Jouni Malinen <j@w1.fi>
mac_addr=2 and preassoc_mac_addr=2 parameters can now be used to
configure random MAC address to be generated by maintaining the OUI part
of the permanent MAC address (but with locally administered bit set to
1). Other than that, these values result in similar behavior with
mac_addr=1 and preassoc_mac_addr=1, respectively.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds experimental support for wpa_supplicant to assign random local
MAC addresses for both pre-association cases (scan, GAS/ANQP) and for
connections. MAC address policy for each part can be controlled
separately and the connection part can be set per network block.
This requires support from the driver to allow local MAC address to be
changed if random address policy is enabled. It should also be noted
that number of drivers would not support concurrent operations (e.g.,
P2P and station association) with random addresses in use for one or
both.
This functionality can be controlled with the global configuration
parameters mac_addr and preassoc_mac_addr which set the default MAC
address policies for connections and pre-association operations (scan
and GAS/ANQP while not connected). The global rand_addr_lifetime
parameter can be used to set the lifetime of a random MAC address in
seconds (default: 60 seconds). This is used to avoid unnecessarily
frequent MAC address changes since those are likely to result in driver
clearing most of its state. It should be noted that the random MAC
address does not expire during an ESS connection, i.e., this lifetime is
only for the case where the device is disconnected.
The mac_addr parameter can also be set in the network blocks to define
different behavior per network. For example, the global mac_addr=1 and
preassoc_mac_addr=1 settings and mac_addr=0 in a home network profile
would result in behavior where all scanning is performed using a random
MAC address while connections to new networks (e.g.,
Interworking/Hotspot 2.0) would use random address and connections to
the home network would use the permanent MAC address.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, eight character random passphrase was generated
automatically for P2P GO. The new p2p_passphrase_len parameter can be
used to increase this length to generate a stronger passphrase for cases
where practicality of manual configuration of legacy devices is not a
concern.
Signed-off-by: Jouni Malinen <j@w1.fi>
Performing a P2P Device flow such as p2p_listen or
p2p_find, can degrade the performance of an active interface
connection, if the listen frequency is different than the
frequency used by that interface.
To reduce the effect of P2P Device flows on other interfaces,
try changing the listen channel of the P2P Device to match the
operating channel of one of the other active interfaces. This change
will be possible only in case that the listen channel is not forced
externally, and will be delayed to a point where the P2P Device
state machine is idle.
The optimization can be configured in the configuration file and
is disabled by default.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This makes the p2p_find default delay value configurable as
p2p_search_delay parameter through the configuration file (and through
control interface "SET p2p_search_delay <value>" on the P2P management
interface.
This parameter controls the number milliseconds of extra delay that is
added between search iterations when there is a concurrent operation in
progress. This can be used, e.g., p2p_search_delay=100 to make p2p_find
friendlier to concurrent operations by avoiding it from taking 100% of
the radio resources. The default value is the previous default, i.e.,
500 ms. Smaller values can be used to find peers more quickly at the
cost of larger effect to concurrent operations while a larger value
leaves more time for the concurrent operations at the cost of making
device discovery take longer time.
The optional p2p_find delay argument can still be used to override the
search delay for each search operation.
Since the P2P_CONCURRENT_SEARCH_DELAY macro is not used anymore, the
driver specific build parameter for bcmdhd from Android.mk is also
removed. Similar configuration can now be achieved with
p2p_search_delay=0 in the p2p0 interface configuration file.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a new wowlan_triggers option to wpa_supplicant.conf. The triggers in
this key will be used to configure the kernel wowlan configuration.
For now, support only simple flags. More complex triggers can be added
later on.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
This allows the specific SIM to be identified for authentication
purposes in multi-SIM devices. This SIM number represents the index of
the SIM slot. This SIM number shall be used for the authentication using
the respective SIM for the Wi-Fi connection to the corresponding
network.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
"GET_CRED <id> <field>" can now be used to fetch credential parameters
over the control interface. This does not allow passwords etc. private
material to be retrieved ("*" is returned for those if the value is set
regardless of the value). FAIL is returned if the requested parameter
has not been set. For cred parameters that can have multiple values,
newline separated list of values is returned.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new parameter can be used to configure credentials to mandate use
of OCSP stapling for AAA server authentication.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This new priority parameter can be used to specify priorities between
credentials provisioned by the same SP. cred->priority is checked first
and if it is same and the provisioning_sp parameter matches, the new
sp_priority is used to order the credentials. It should be noted that
the order of priorities is different (higher 'priority' value indicates
higher priority of the credential, while higher 'sp_priority' indicates
lower priority of the credential).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new credential parameter req_conn_capab can be used to specify
restrictions on roaming networks providing connectivity for a set of
protocols/ports.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new credential parameter max_bss_load can be used to specify
restrictions on BSS Load in the home network.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new credential parameters min_{dl,ul}_bandwidth_{home,roaming} can
be used to specify restrictions on available backhaul bandwidth.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new provisioning_sp cred field can now be used to track which SP
provisioned the credential. This makes it easier to find the matching
PPS MO from the management tree (./Wi-Fi/<provisioning_sp>).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_cli fetch_osu command can be used to fetch information about
all OSU providers and write that to a text file with the icons in
separate files. cancel_osu_fetch command can be used to stop ongoing OSU
provider list fetch.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The HS 2.0 Indication element from wpa_supplicant now includes the
release number field and wpa_supplicant shows the release number of the
AP in STATUS command (hs20=1 replaced with hs20=<release>).
The new update_identifier field in the cred block can now be used to
configure the PPS MO ID so that wpa_supplicant adds it to the Indication
element in Association Request frames.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new roaming_partner parameter within a cred block can be used to
configure priorities for roaming partners.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This new mechanism allows P2P Client to request an IPv4 address from the
GO as part of the 4-way handshake to avoid use of DHCP exchange after
4-way handshake. If the new mechanism is used, the assigned IP address
is shown in the P2P-GROUP-STARTED event on the client side with
following new parameters: ip_addr, ip_mask, go_ip_addr. The assigned IP
address is included in the AP-STA-CONNECTED event on the GO side as a
new ip_addr parameter. The IP address is valid for the duration of the
association.
The IP address pool for this new mechanism is configured as global
wpa_supplicant configuration file parameters ip_addr_go, ip_addr_mask,
ip_addr_star, ip_addr_end. For example:
ip_addr_go=192.168.42.1
ip_addr_mask=255.255.255.0
ip_addr_start=192.168.42.2
ip_addr_end=192.168.42.100
DHCP mechanism is expected to be enabled at the same time to support P2P
Devices that do not use the new mechanism. The easiest way of managing
the IP addresses is by splitting the IP address range into two parts and
assign a separate range for wpa_supplicant and DHCP server.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
All te network blocks and credentials were already cleared, but
configurations blobs should also be cleared here, e.g., to get
more consistent behavior test cases using EAP-FAST PACs.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new cred block parameter 'temporary' can be used to indicate that a
cred block is not to be saved to wpa_supplicant configuration file
(e.g., "SET_CRED 0 temporary 1"). This is similar to the concept of
temporary network blocks and allows cred blocks to be managed outside
the wpa_supplicant config file when other parameters are still saved to
the file written by wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
There are use cases requesting the host driver to initiate the TDLS
setup with the peer only when configured by the external applications.
Thus, enable this control by tdls_external_control=1 and pass the
requisite information for the specific TDLS operation to the driver
on the request from such use cases.
This operation mode expects the driver to initiate TDLS link
automatically based on signal strength and traffic to a peer and tear
down links whenever they are not used or suitable due to signal strength
etc. The list of peers with which such operations are to be performed
are provided with the TDLS driver operations.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This option can be used to globally configure bgscan parameters
for all the network blocks.
Note that this configuration will not override a network block
specific bgscan settings, but will only be used in case that
the network block does not have a valid bgscan configuration.
Signed-hostap: Haim Dreyfuss <haim.dreyfuss@intel.com>
Add the option to ask for VHT operation similarly to the way ht40 is
configured - either by adding 'vht' param to the relevant p2p_*
commands or by configuring p2p_go_vht=1 in the configuration file.
This patch only adds the configuration option (e.g., via control
interface). The actual handling of the VHT parameter (asking the driver
to use VHT, etc.) will be done by the following patch.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
The new p2p_add_cli_chan=1 configuration parameter can be used to
request passive-scan channels to be included in P2P channel lists for
cases where the local end may become the P2P client in a group. This
allows more options for the peer to use channels, e.g., if the local
device is not aware of its current location and has marked most channels
to require passive scanning.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new p2p_no_go_freq frequency range list (comma-separated list of
min-max frequency ranges in MHz) can now be used to configure channels
on which the local device is not allowed to operate as a GO, but on
which that device can be a P2P Client. These channels are left in the
P2P Channel List in GO Negotiation to allow the peer device to select
one of the channels for the cases where the peer becomes the GO. The
local end will remove these channels from consideration if it becomes
the GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new configuration parameter external_sim=<0/1> can now be used to
configure wpa_supplicant to use external SIM/USIM processing (e.g., GSM
authentication for EAP-SIM or UMTS authentication for EAP-AKA). The
requests and responses for such operations are sent over the ctrl_iface
CTRL-REQ-SIM and CTRL-RSP-SIM commands similarly to the existing
password query mechanism.
Changes to the EAP methods to use this new mechanism will be added in
separate commits.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows credentials to be limited from being used to connect to a
network unless the AP advertises a matching roaming consortium OI.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allow domain_suffix_match to be specified for a cred block and then
get this copied for the network blocks generated from this credential as
part of Interworking network selection.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Credentials can now be configured with more than one FQDN ('domain'
field in the cred block) to perform Domain Name List matching against
multiple home domains.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If a VIF is already associated, then only scan on the associated
frequency if user requests such. This is a big help when using
lots of virtual stations.
Signed-hostap: Ben Greear <greearb@candelatech.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
The new sched_scan_interval parameter can be used to set the default
sched_scan interval, e.g., for power saving purposes.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows one to limit the channels that wpa_supplicant will
scan. This is a useful addition to the freq_list configurable
in the network {} section.
Signed-hostap: Ben Greear <greearb@candelatech.com>
