Previously, driver_nl80211 sets NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT in
AP mode, to get EAPOL frames out unencrypted when using IEEE 802.1X/WEP.
However, due to the way nl80211/cfg80211 is implemented, this attribute
is ignored by the kernel if NL80211_ATTR_CONTROL_PORT_ETHERTYPE isn't
specified as well. Fix this by including
NL80211_ATTR_CONTROL_PORT_ETHERTYPE set to ETH_P_PAE. This can be done
unconditionally, since the kernel will allow ETH_P_PAE to be set even
when the driver didn't advertise support for arbitrary ethertypes.
Additionally, the params->pairwise_ciphers appear to not be set at
this point, so relax the check and allow them to be zero.
In client mode, this whole thing was missing, so add it. Again, the
pairwise suite can be WPA_CIPHER_NONE, so allow that case as well.
This fixed IEEE 802.1X/WEP EAP reauthentication and rekeying to use
unencrypted EAPOL frames which is the de facto way of implementing this
in wireless networks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This makes wpa_supplicant set default scan IEs to the driver (if the
vendor command is supported). The driver can use these IEs in the scan
requests initiated by the driver itself. Also the driver can merge these
IEs into further scan requests that it receives, in case if the scan
request doesn't carry any of the IEs sent in this command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If params->freq is NULL here, it leads to a segfault. Do not initialize
bss->bandwidth if params->freq is NULL.
Signed-off-by: Chaitanya T K <Chaitanya.Mgit@gmail.com>
Previously, HT capability IE and HT information IE were included in
Beacon and Mesh Peering Open/Confirm frames even if HT is disabled with
disable_ht=1. This patch removes these.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Previously, mesh power management functionality works only with kernel
MPM. Because user space MPM did not report mesh peer AID to kernel,
the kernel could not identify the bit in TIM element. So this patch
reports mesh peer AID to kernel.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This allows P2P Listen to be offloaded to device to enhance power
saving.
To start P2P listen offload, from wpa_cli interface, issue the command:
p2p_lo_start <freq> <period> <interval> <count>
To stop P2P listen offload, issue the command:
p2p_lo_stop
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
During the P802.11s draft development, there were separate LISTEN and
IDLE states. However, the current IEEE 802.11 standards uses only the
IDLE state while the implementation called this LISTEN. Rename the state
in the implementation to match the one used in the standard to avoid
confusion. In addition, rename OPEN_{SENT,RCVD} to OPN_{SNT,RCVD} to
match the exact spelling of these states in the standard.
Signed-off-by: Jouni Malinen <j@w1.fi>
Set max peer links to kernel even when wpa_supplicant MPM is used. This
sets the correct value for the "Accepting Additional Mesh Peerings bit"
in "Mesh Capability field" in "Mesh Configuration element" in the Beacon
frame.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This adds the necessary changes to support extraction and use of the
extended capabilities specified per interface type (a recent
cfg80211/nl80211 extension). If that information is available,
per-interface values will be used to override the global per-radio
value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes changes such that hostapd (and wpa_supplicant AP mode)
registers to kernel for specific Action frames instead of generically
registering for all Action frames. This makes it easier for other
programs to register for some Action frames that hostapd does not handle
today without having to somehow coordinate directly with hostapd.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
One of supported code paths already allows this scenario. It is used if
driver doesn't report NL80211_ATTR_DEVICE_AP_SME and doesn't support
monitor interface. In such situation:
1) We don't quit if subscribing for WLAN_FC_STYPE_PROBE_REQ fails
2) We don't try subscribing for WLAN_FC_STYPE_ACTION
3) We fallback to AP SME mode after failing to create monitor interface
4) We don't quit if subscribing for WLAN_FC_STYPE_PROBE_REQ fails
Above scenario is used, e.g., with brcmfmac. As you can see - thanks to
events provided by cfg80211 - it's not really required to receive Probe
Request or action frames.
However, the previous implementation did not allow using hostapd with
drivers that:
1) Report NL80211_ATTR_DEVICE_AP_SME
2) Don't support subscribing for PROBE_REQ and/or ACTION frames
In case of using such a driver hostapd will cancel setup after failing
to subscribe for WLAN_FC_STYPE_ACTION. I noticed it after setting flag
WIPHY_FLAG_HAVE_AP_SME in brcmfmac driver for my experiments.
This patch allows working with such drivers with just a small warning
printed as debug message.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
The os_snprintf() call here cannot really fail in practice, but since
its result was stored into the local variable and not checked, static
analyzers could warn about the unused assignment. Clean this up by
checking the return value.
Signed-off-by: Jouni Malinen <j@w1.fi>
Set the global RRM flag if global RRM is supported by the device. Also,
allow RRM in (Re)Association Request frame if the global RRM flag is
set.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Register to receive Radio Measurement Request frames since LCI request
is supported by wpa_supplicant.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Implement configure_data_frame_filters() callback by using
the net-sysfs interfaces (if these are available).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
If a legacy client with no P2P PS support is trying to connect to
a P2P GO, the driver should know that, and change its PS behavior
accordingly.
Add a parameter to hostapd_sta_add_params() indicating if P2P PS is
supported by the station and pass this parameter to kernel with nl80211
driver when the station is added/set.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
cfg80211 reports a deauth/disassoc event when internally clearing
connection with the previous BSS. Ignore that event to allow the new
connect command to complete.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier for drivers that use the Connect command instead of
separate Auth+Assoc commands to determine when to use reassociation
instead of association. Matching changes are still needed in cfg80211 to
allow this parameter to be used, but it is safe for wpa_supplicant to
start including this attribute now since it will be ignored by older
cfg80211 versions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Interface additions/removals are not guaranteed to be for the driver
listening to the kernel events. As such, send the events to
wpa_supplicant_event_global() which can then pick the correct interface
registered with wpa_supplicant to send the event to.
Signed-off-by: Roy Marples <roy@marples.name>
Commit 732b1d20ec ('nl80211: Clean up
ifidx properly if interface in a bridge is removed') added
drv->if_indices_reason array similarly to the previously used
drv->if_indices. However, it had a copy-paste error here on the error
path where a reallocation failure after at least one successful
reallocation would result in the drv->if_indices being overridden
instead of restoring drv->if_indices_reason to the old value. Fix this
by setting the correct variable on the error path. (CID 138514)
Signed-off-by: Jouni Malinen <j@w1.fi>
SMPS mode is applicable only for HT and including an attribute to
configure it when HT is disabled could result in the AP start operation
failing. Fix this by adding the attribute only in cases where HT is
enabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Since commit cb05808c46 ('nl80211: Generic
Linux master interface support for hostapd'), hostapd is listening for
EAPOL frames on any master which the interface is enslaved under.
This commit allows hostapd to support network hierarchy in which the
interface is enslaved under some master which in turn is enslaved under
a bridge.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
When an interface is removed while it was in a bridge, the bridge was
not removed from the local ifidx list.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
If the driver supports 64-bit TX/RX byte counters, use them directly.
The old 32-bit counter extension is maintained for backwards
compatibility with older drivers.
For nl80211 driver interface, the newer NL80211_STA_INFO_RX_BYTES64 and
NL80211_STA_INFO_TX_BYTES64 attributes are used when available. This
resolves the race vulnerable 32-bit value wrap/overflow. Rework RADIUS
accounting to use these for Acct-Input-Octets, Acct-Input-Gigawords,
Acct-Output-Octets, and Acct-Output-Gigawords, these values are often
used for billing purposes.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
This provides means for determining whether the driver supports full AP
station state and setting the needed STA flags for using this
functionality.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
While most C libraries print "(null)" when NULL is used as an argument
to printf format string %s, this is not really necessary to print here,
so move the debug print to be after the NULL check.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
PBSS (Personal Basic Service Set) is a new BSS type for DMG
networks. It is similar to infrastructure BSS, having an AP-like
entity called PCP (PBSS Control Point), but it has few differences.
PBSS support is mandatory for IEEE 802.11ad devices.
Add a pbss flag to the relevant structures to support starting a PCP and
connecting to a PCP. Implement support in the nl80211 driver by using
the new PBSS flag attribute.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
The called function nl80211_ht_vht_overrides() was not freeing "msg"
resource in error cases.
Signed-off-by: Purushottam Kushwaha <p.kushwaha@samsung.com>
As a dedicated P2P Device interface does not have a network
interface associated with it, trying to call linux_iface_up()
on it would always fail so this call can be skipped for
such an interface.
Getting interface nlmode can be done only after bss->wdev_id is
set, so move this call to wpa_driver_nl80211_finish_drv_init(),
and do it only in case the nlmode != NL80211_IFTYPE_P2P_DEVICE.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
On systems that have multiple WLAN rfkill instances, the rfkill code
can become confused into thinking that the device was unblocked when
in fact it wasn't, because it only matches on the WLAN type.
Since it then stores the new (unblocked) state from the wrong rfkill
instance, it will never retry the failing IFF_UP operation and the
user has to toggle rfkill again, or otherwise intervene manually, in
this case to get back to operational state.
Fix this by using the existing (but unused) ifname argument when the
rfkill instance is created to match to a specific rfkill index only.
As a P2P Device interface does not have a netdev interface associated
with it, use the name of a sibling interface to initialize the rfkill
context for the P2P Device interface. For nl80211, as the wiphy index
is known only after getting the driver capabilities from the kernel,
move the initialization of the rfkill object to
wpa_driver_nl80211_finish_drv_init().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The rfkill processing in nl80211 driver assumes that the
INTERFACE_ENABLED/DISABLED will be also issued, so does not do much in
the rfkill callbacks. However, as a P2P Device interface is not
associated with a network interface, these events are not issued for it.
Handle rfkill events for the P2P_DEVICE interface by faking the
INTERFACE_ENABLED/DISABLED.
Signed-off-by: Moshe Benji <Moshe.Benji@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
These needs to be cancelled so that the kernel driver does not get left
with all old entries blocking other offchannel operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add 'scan plans' to driver scan parameters for scheduled scan.
Each 'scan plan' specifies the number of iterations to run the scan
request and the interval between iterations. When a scan plan
finishes (i.e., it was run for the specified number of iterations),
the next scan plan is executed. The last scan plan will run
infinitely.
The maximum number of supported scan plans, the maximum number of
iterations for a single scan plan and the maximum scan interval
are advertised by the driver.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This adds the driver interface commands for issuing a request to abort
an ongoing scan operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
NL80211_CMD_GET_STATION does not work with the IBSS/mesh BSSID, so clear
the signal strength instead of returning failure when SIGNAL_POLL is
used in an IBSS/mesh.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When an AP interface it created, it is also setup and subscribes
for management frames etc. However, when the interface is added by
wpa_supplicant, setting up for AP operations is redundant because
it will be done by wpa_supplicant on wpa_drv_init() when setting
the interface mode to AP.
In addition, it may cause wpa_supplicant to fail initializing the
interface as it will try to subscribe for management frames on this
interface but the interface is already registered.
Change this, so when adding an AP interface, make setting up the AP
optional, and use it only when the interface is added by hostapd but not
when it is added by wpa_supplicant.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Some drivers (like mac80211) do not accept changing the TX bitrate mask
before the network interface is up. Thus, calling
nl80211_disable_11b_rates() before the interface is up fails, and the
P2P network interface continues to use invalid bitrates.
To fix this call nl80211_disable_11b_rates() immediately after the
interface is brought up (and also after rfkill is unblocked).
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Some management frames contain CSA counters which should be updated by
kernel. Change driver op send_mlme() allowing to send a frame,
specifying an array of offsets to the CSA counters which should be
updated. For example, CSA offsets parameters should be specified when
sending Probe Response frames during CSA period.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Channel switch may be performed using both CSA and eCSA IEs together.
This may happen, for example with a P2P GO on band A with legacy
clients. Extend driver API to support up to 2 CSA counters.
This patch also includes the required implementation for nl80211.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This allows the binary sizes to be reduced if no support for nl80211
vendor extensions are needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow wpa_supplicant to use vendor scan (if supported by the driver)
together with the normal nl80211 scan and handling external scan events.
Since this results in possibility of concurrent scan operations, some of
the operations related to scan results need to check more carefully when
an event is relevant for a specific interface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows an empty nested list (i.e., no MAC addresses) to be included
in the NL80211_CMD_SET_MAC_ACL message unlike with
nla_nest_start()/nla_nest_end() where the current libnl implementation
removes the "empty" attribute and causes cfg80211 to reject the command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend the QCA vendor specific nl80211 interface to query the preferred
frequency list from driver and add a new wpa_cli command to query this
information.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
