Add QCA vendor attributes to configure the driver to enable/disable the
Broadcast TWT support and Rx Control Frame To MultiBSS support in HE
capabilities information field. This attribute is used for testing
purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Update QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME_TSF
TWT attribute to use it in TWT setup command to pass TSF value.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add new QCA vendor attribute to configure the driver to enable/disable
the BSS max idle period support. This attribute is used for testing
purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to configure the driver to use scan
request BSSID value in Probe Request frame RA(A1) for scan.
This attribute is used for testing purpose.
The driver saves this configuration and applies this setting to all user
space scan requests until the setting is cleared. If this configuration
is set, the driver uses the BSSID value from the scan request to set the
RA(A1) in the Probe Request frames during the scan, else the broadcast
address is set in the Probe Request frames RA(A1).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA vendor interface to configure the driver which transport mode to
use for sending CFR data to userspace. Currently, relayfs and netlink
event modes are supported.
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
Add a QCA vendor attribute to configure the driver to use Data or
Management frames for keep alive data. This attribute is used for
testing purpose.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA vendor attribute to configure the driver to transmit the
Data frames with ER SU PPDU type format. This attribute is used
for testing purpose.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA vendor attribute QCA_WLAN_VENDOR_ATTR_CONFIG_FT_OVER_DS
to configure FT over DS to the driver/firmware.
Signed-off-by: Vinita S. Maloo<vmaloo@codeaurora.org>
Add QCA interface to specify the RSSI thresholds separately for candidate
APs from different bands.
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
Mention that for AP mode this attribute is required in
response for TWT SET, TWT GET, TWT SUSPEND, and TWT
TERMINATE. And is required in request for TWT GET, and
TWT TERMINATE.
For STA mode, the usage of this attribute remains unchanged.
Signed-off-by: Mohammad Asaad Akram <asadkrm@codeaurora.org>
Add QCA vendor interface for userspace to get information of usable
channels for different interface types from the driver/firmware.
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
The firmware rejects the TWT setup request when scan is in
progress. Extend enum qca_wlan_vendor_twt_status to represent new
reason code for it.
Signed-off-by: Mohammad Asaad Akram <asadkrm@codeaurora.org>
Define a new reason code in enum qca_wlan_vendor_hang_reason,
QCA_WLAN_TASKLET_CREDIT_LATENCY_DETECT, for tasklet/credit latency
detection.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Introduce a QCA vendor command to configure the concurrent connection
policies when multiple STA interfaces are (getting) active.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define the new TWT attributes for configuring the broadcast TWT
parameters in enum qca_wlan_vendor_attr_twt_setup.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The firmware rejects the TWT setup request when roaming and channel
switch is in progress. Extend enum qca_wlan_vendor_twt_status to
represent new reason codes for these cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The firmware sends new reason codes to indicate TWT teardown due to
single channel and multi channel concurrency. Update the enum
qca_wlan_vendor_twt_status to represent new reason code.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define the following additional TWT attribute for
qca_wlan_vendor_attr_twt_setup:
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL2_MANTISSA to configure the
mantissa in microseconds.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to configure the driver to allow the 6 GHz
connection with all security types. This attribute is used for testing
purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to ignore SAE H2E requirement mismatch for 6
GHz connection. This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to enable/disable the Punctured Preamble Rx
support in HE PHY capabilities.
This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to configure the driver to disable data and
management response frame transmission to test the BSS max idle period
feature.
This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to configure the driver/firmware to use only
RU 242 tone for data frame transmission.
This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute to configure the driver with a specific BSS
max idle period value to advertise in (Re)Association Request frames.
This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add additional attributes for the QCA vendor command
QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO to get finer details on roaming
behavior, TSF out of sync count, and the latest TX rate, Rate Index used
for the transmission.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The response for the respective TWT operations can either be synchronous
or asynchronous (wherever specified). If synchronous, the response to
this operation is obtained in the corresponding vendor command reply to
the user space. For asynchronous case, the response is obtained as an
event with the same operation type.
Drivers shall support either of these modes but not both simultaneously.
The support for asynchronous mode is advertised through the new flag
QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT. If the driver does not
include this flag, it shall support synchronous mode.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define the following additional TWT operations:
QCA_WLAN_TWT_GET_STATS, QCA_WLAN_TWT_CLEAR_STATS,
QCA_WLAN_TWT_GET_CAPABILITIES, QCA_WLAN_TWT_SETUP_READY_NOTIFY.
Also define new attributes to qca_wlan_vendor_attr_twt_setup
and qca_wlan_vendor_attr_twt_nudge.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define QCA vendor attributes to dynamically configure TX NSS and RX NSS
to be used with QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and
QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION commands.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
TWT nudge is a combination of suspend and resume in a single request.
Add TWT nudge operation and QCA vendor attributes to support
the TWT nudge request.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Introduces a vendor specific feature capability
QCA_WLAN_VENDOR_FEATURE_CONCURRENT_BAND_SESSIONS to know if the device
supports concurrent network sessions on different Wi-Fi bands. This feature
capability is attributed to the hardware's capability to support the same
(e.g., DBS).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define a QCA vendor attribute
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_FULL_BW_UL_MU_MIMO to
enable/disable full bandwidth UL MU-MIMO subfield in the HE PHY
capabilities information field for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The connection process fails for several reasons and the status codes
defined in IEEE Std 802.11 do not cover the locally generated reason
codes. Add an attribute to QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO vendor
sub command which can be used by the driver/firmware to report various
additional reason codes for connection failures.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Introduce QCA_ATTR_ROAM_CONTROL_SCAN_SCHEME_TRIGGERS that represents the
triggers for which the scan scheme from enum qca_roam_scan_scheme has to
be applied.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The firmware sends a new status code to indicate an already suspended
TWT session. Update the status code enum to represent this state.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add additional attributes to enum qca_vendor_attr_roam_control to
control the roam behavior through QCA_NL80211_VENDOR_SUBCMD_ROAM and
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_CONTROL.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add new QCA vendor attributes to get thermal level from the driver. The
driver may return thermal level when userpace requests, or send a
thermal event when thermal level changes.
Signed-off-by: Hu Wang <huw@codeaurora.org>
This change adds QCA_NL80211_VENDOR_SUBCMD_MBSSID_TX_VDEV_STATUS,
and enum for qca_wlan_vendor_attr_mbssid_tx_vdev_status to notify
Tx VDEV status.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new vendor attribute for GPIO configuration. In addition, document
the previously defined attributes.
Signed-off-by: Chaoli Zhou <zchaoli@codeaurora.org>
Firmware statistics are received in the driver as opaque data. The host
target needs to send this opaque data to userspace wifistats
application. This new event is used to transfer this opaque data to the
application.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
