Extend the minimal HT 20/40 co-ex support to include dynamic changes
during the lifetime of the BSS. If any STA connects to a 2.4 GHz AP with
40 MHz intolerant bit set then the AP will switch to 20 MHz operating
mode.
If for a period of time specified by OBSS delay factor and OBSS scan
interval AP does not have any information about 40 MHz intolerant STAs,
the BSS is switched from HT20 to HT40 mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This provides information to allow the driver to be configured for
updated channel parameters, e.g., when dynamically changing HT20/HT40
bandwidth.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There could be pending unsolicited event messages on the monitor socket
when the DETACH command is issued. As such, the response may be
something else then OK even if the actual detach operation succeeded.
Try to avoid this be dropping pending messages before issuing the detach
command. As an additional workaround, check the response against FAIL
instead of requiring OK so that the self.attached does not get left to
True incorrectly even if an additional event message were to be
received.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for the disconnection event from the driver to not get
delivered when interface is disabled. To maintain consistent ctrl_iface
event behavior, indicate CTRL-EVENT-DISCONNECTED in such a case if we
were in connected state.
Signed-off-by: Jouni Malinen <j@w1.fi>
If two config files are merged together, the ssid and cred blocks may
not have been processed correctly since the tail pointers were not
updated to the last entry from the first configuration file.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like the demangle.h from binutils-dev is not installed that
commonly anymore. Since we need only two defines from that file, replace
the header file with those defines to make it easier to build with
WPA_TRACE_BFD=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
Some trailing whitespace and spaces for indentation were present in the
driver wrapper and header files.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Move the definitions that depended in common.h into a separate header
file so that qca-vendor.h can be copied and used as-is in other
projects.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allocates a QCA vendor subcmd for extended statistics
functionality and also an attribute for delivering the payload
for extended statistics.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the frequency conflict was handled only during the
association flow. However, some drivers, e.g., mac80211 based
drivers, will fail an authentication request in case that there
are no available channels for use (as they might be used by
other interfaces), and thus the frequency conflict resolution
is never called.
Fix this by calling frequency conflict resolution during
authentication (SME-in-wpa_supplicant) as well.
In addition, get the shared radio frequency from the wpa_s context in
both the SME-in-driver and SME-in-wpa_supplicant cases and not from the
driver.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The normal scan counter is used to trigger a few normal scans before a
scheduled scan is issued. The reason for doing this is that we get
results faster and some drivers support more SSIDs per normal scan
than during sched scan. After 2 normal scans, we start using
sched_scan. But the problem is that when a connection succeeds, we do
not reset this counter, so we will keep using sched scans.
To fix this, now we reset the counter when we switch to WPA_COMPLETED
state.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
These functions are not standard and do not exist in all systems, e.g.,
variants of Android. Instead use the macros defined in common.h.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This avoids large number of undesired compiler warnings since Android
build system is added -Wextra.
Signed-off-by: Greg Hackmann <ghackmann@google.com>
With hidden SSID (ignore_broadcast_ssid), an IOS device trying to
connect to the AP will send a probe request with ANT == 2. If
interworking support is just compiled (not enabled), we will drop the
probe request since default ANT is 0.
Check that interworking is enabled before filtering based on ANT or
HESSID to match the behavior of code without CONFIG_INTERWORKING.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
This allows the specific SIM to be identified for authentication
purposes in multi-SIM devices. This SIM number represents the index of
the SIM slot. This SIM number shall be used for the authentication using
the respective SIM for the Wi-Fi connection to the corresponding
network.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Sometimes function hostapd_is_dfs_required() returns -1 which indicates
that it was not possible to check if DFS was required. This happens for
channels from the 2.4 GHz band where DFS checking should not happen.
This can be fixed by returning DFS-not-required for mode different from
IEEE80211A and when DFS support is not available (ieee80211h not set).
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Some of the buffers used to keep a copy of PTK/TPTK/GTK in the
supplicant implementation maintained a copy of the keys longer than
necessary. Clear these buffers to zero when the key is not needed
anymore to minimize the amount of time key material is kept in memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous version prevented all use of wpas_global_ctrl_iface_set().
That's not desirable since there may be more global parameters added in
the future. Instead, try to use the global version first and redirect to
P2P interface only if the global version returns an error.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The P2P redirection for SAVE_CONFIG issued on the global control
interface was preventing wpas_global_ctrl_iface_save_config() from being
reached. The global version of SAVE_CONFIG was supposed to try to save
configuration files for all interface rather than just the P2P
management interface, so fix this by removing the unneeded and undesired
redirection.
Modify the global SAVE_CONFIG handler to return FAIL if no configuration
files were saved. This makes the behavior match with the per-interface
SAVE_CONFIG.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Rename the eap_proxy_*.mk file to eap_proxy_*.mak for non-Android builds
so that the same eap_proxy implementation can be more easily included in
the same directory for both cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It turned out that the initial test case found the GO based on the
initial full scan instead of the progressive search part. Fix this by
started the GO only after the initial full scan.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, it was possible to remove the main interface and leave
behind dynamic P2P group interfaces. This would eventually result in
references freed memory, so it is not really suitable behavior. Instesd,
remove all the dynamic P2P group interfaces that were created through an
interface that is now removed.
Signed-off-by: Jouni Malinen <j@w1.fi>
The sample code here ended up trying to register an eloop socket with fd
== -1. This was not really ever supposed to be used, but it is now also
hitting an assert in eloop. Skip the unnecessary
eloop_register_read_sock() to avoid this.
This was causing issues for hostapd since CONFIG_L2_PACKET is not set by
default. If CONFIG_RSN_PREAUTH=y was not used for CONFIG_L2_PACKET was
not set in .config explicitly, the defaul use of l2_packet_none.c ended
up hitting the newly added assert() in eloop.
Signed-off-by: Jouni Malinen <j@w1.fi>
This can fail if Probe Response frame is missed and Beacon frame was
used to fill in the BSS entry. This can happen, e.g., during heavy load
every now and then and is not really an error, so try to workaround by
runnign another scan.
Signed-off-by: Jouni Malinen <j@w1.fi>
It seems like it is possible for a CTRL-EVENT-REGDOM-CHANGE event from a
previous test case to "leak" through to the execution of this test case.
That can result in the validation steps here failing, so wait a bit and clear the pending events before starting the test.
Signed-off-by: Jouni Malinen <j@w1.fi>
ap_multi_bss_acs test case was failing if it was executed immediately
after a test case that used 5 GHz band since the current mac80211_hwsim
channel survey implementation is very limited and reports only a single
channel. For this test case, that channel has to be from the 2.4 GHz
band.
Signed-off-by: Jouni Malinen <j@w1.fi>
Rather than ignoring packets with a minimal 8-byte radiotap
header, which may occur elsewhere, tag generated (decrypted)
packets with an empty vendor namespace tag and ignore those.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Update the radiotap parser to the latest version of the
http://git.sipsolutions.net/radiotap.git/ library to get
parsing for vendor namespaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we receive a scan request via D-Bus and wpa_supplicant_scan_trigger
fails, return the failure to the caller over D-Bus.
Signed-hostap: mukesh agrawal <quiche@chromium.org>
Use eloop timeout to run the reconnect command after eapol_cb has
returned. This reduces stack use and can simplify the driver
command/event sequence by allowing the disconnection events from the
provisioning step to be processed before starting the actual data
connection.
Signed-off-by: Jouni Malinen <j@w1.fi>
If a P2P GO issues multiple credentials for some reason, clone the
p2p_group and temporary parameters to all those based on the initial
network block that gets used for the first credential.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was already done for the disconnect event, but
SME-in-wpa_supplicant case needs to do same with the deauth event to
avoid getting extra events during WPS disconnect-and-reconnect sequence.
This can speed up WPS processing by removing unnecessary failures or
retries due to the extra event being processed during the next
association attempt.
Signed-off-by: Jouni Malinen <j@w1.fi>
