Try to find the BSS entry that contains the most likely current
information for the target BSS. This is mainly needed to avoid some
unusual behavior with APs changing their Beacon frame information in a
manner that shows up in automated testing, but this might help with some
more dynamic real world uses as well, so better do the BSS entry search
for the newest entry.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This wrapper function was not used at all, so remove it to make it
clearer that the set_ap() driver op is called only from hostapd code.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
In case we run command like:
wpa_cli -g <global_ctrl_path> command
don't print
"Selected interface " message.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
When wpa_supplicant needed to update the internal BSS table with the
latest scan results from the driver, it fetched all BSSs and processed
them all. This is unnecessary for cases where an update is needed only
for a specific BSS. Optimize this by filtering out the unnecessary
entries from the results.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Commit 117e812d06 ("Update BSS table entry if roaming event indicates
frequency change") added wpa_supplicant BSS table update based on the
latest driver scan results whenever processing an association event that
results in the current operating channel changing. While that is needed
to cover the case where an AP changes its own operating channel (and
that is noticed as a roam or new connection instead of a channel switch
event), this should not really be needed for cases where the
wpa_supplicant entry for the new BSS is already up to date.
Skip the full BSS table update on association event if the event is for
a roaming case to a different BSS and the BSS entry for the target is
already available and for the current operating channel. This avoids
undesired latency when processing the association event.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Update EAP-WSC parameters to include Multi-AP profile info to pass the
profile information through the provisioning steps. This is needed for
provisioning the STA configuration when different profiles are used.
Signed-off-by: Manoj Sekar <quic_sekar@quicinc.com>
Allow both hostapd and wpa_supplicant to be configured with the
supported Multi-AP profile. The configured value will be advertised in
the Multi-AP element.
Signed-off-by: Manoj Sekar <quic_sekar@quicinc.com>
This makes it more convenient to handle extensions to the element and
allows code to be shared between hostapd and wpa_supplicant.
Signed-off-by: Manoj Sekar <quic_sekar@quicinc.com>
Add ANQP fields to the BSS properties to allow DBus clients to be
notified and obtain the values when it changes.
Signed-off-by: Damien Dejean <damiendejean@chromium.org>
Add a D-Bus method to perform ANQP get requests. The new method is
equivalent to the "anqp_get" command available in wpa_cli.
Signed-off-by: Damien Dejean <damiendejean@chromium.org>
To implement an action script that listens for DPP push button events
and for example blinks a LED it is useful to know when push button has
started. Emit an event when push button starts.
Signed-off-by: Evan Benn <evan.benn@morsemicro.com>
This is needed to be able to check validity of the channel parameters
for cases where EHT puncturing impacts what can be enabled for
HT/VHT/HE.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Only the 2.4 and 5 GHz channels were handled previously when removing
operating classes from the Supported Operating Classes element based on
the freq_list parameter. Extend this to include the 6 GHz band as well.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
A previous workaround was used to move the special operating class 130
to the end of the Supported Operating Classes element to avoid getting
any following entry being ignored or misunderstood. That is not really
the correct way of encoding the special cases, i.e., 80+80 MHz channels
that use two nonadjacent frequency segments.
Add support for encoding the 80+80 MHz channel with the 2-octet
operating class design using the Operating Class Duple sequence field of
the Supported Operating Classes element instead of listing the operating
classes that have the 80+ behavior limit set indication in Table E-4
(i.e., opclass 130 and 135) as 1-octet operating classes in the
Operating Classes field.
Fixes: a92660a00e ("Work around Supported Operating Classes element issues for 6 GHz")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Commit 085a3fc76e ("EHT: Add 320 channel width support") added this in
various places, but it did not cover everything. Extend this support to
be more complete. In particular, this allows wpa_supplicant to report
the operating class 137 in the Supported Operating Classes element and
to use it when processing beacon requests.
Signed-off-by: Ainy Kumari <quic_ainykuma@quicinc.com>
The INT_RANGE() cases for wpa_supplicant global and network profile
parameters ended up changing the configured value to the minimum value
if the provided value was too small or to the maximum value if the
provided value was too large. This does not seem most logical. Change
this to not change the configured value at all if the provided value is
outside the valid range.
Signed-off-by: Jouni Malinen <j@w1.fi>
These parameters have both a separate SET command handler and a global
configuration parameter handler. Only the global configuration parameter
handler for enforcing valid range checking. Do that for the SET command
as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
The following config file contains invalid items:
----
filter_rssi=1234 # should be rejected
network={
mode=-1 # should be rejected
ssid="ssid"
psk="password"
}
----
But it is accepted by the config parser. The issue is due to using NULL
to represent no limit. If a boundary is set to 0, it's disregarded.
Fix this.
Note that string parser is not affected as length cannot be negative and
we are not limiting any string to be always empty.
Signed-off-by: Chien Wong <m@xv97.com>
Use of wpa_s->p2p_go_no_pri_sec_switch needs to be conditional on
CONFIG_P2P being defined for the build to avoid a compilation error and
ssid->p2p_group to avoid using this for non-P2P AP mode case in
wpa_supplicant. Furthermore, it is better to clear this flag when
stopping a P2P GO to reduce risk of this getting used for a separate
instance of starting a GO.
Fixes: b18d957593 ("P2P: Disable pri/sec channel switch for GO with forced frequency")
Signed-off-by: Jouni Malinen <j@w1.fi>
In the MLD case, the information from the transition management request
is relevant during the association process in order to filter out links
that were disallowed by the BTM request. Also, the information remains
useful should a connection attempt fail.
To enable these scenarios, keep the information around until the
connection has completed. As this might make it impossible to establish
a connection, also clear this information at the same time that a normal
BSS ignore is cleared to avoid getting stuck in case the transition
fails unexpectedly.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
If the last link is dropped, it makes sense to follow the BTM procedure.
However, in that case we need to prevent reconnection to this link
specifically, while if the AP MLD is terminating we need to forbid
connecting to the AP MLD.
As such, add a new variable to track the BSSID or AP MLD MAC address.
Which one it refers to depends on whether wnm_link_removal is set.
This also simplifies the check in wnm_is_bss_excluded() and untangles it
from wpa_s->current_bss.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
All callers of wnm_send_bss_transition_mgmt_resp() are explicitly
passing wpa_s->wnm_dialog_token. As such, we might as well not pass it
and use the variable directly.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
There is no point in the caller to set it to zero. Just do so within
wnm_send_bss_transition_mgmt_resp().
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
The elements are (currently) not used except for sending an immediate
response similar to COLOC_INTF_REPORT with the main difference being
that the dialog token is included.
Do not store the elements. It easy enough to re-add this should the
implementation improve. And this fixes the fact that the variable is
cleared at odd times as wnm_deallocate_memory() is used specifically to
clear the neighbor report list of a BTM request.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
There is no need for this check as wpa_scan_res_match() already calls
the function through wpa_scan_res_ok() before accepting a match.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
The call to wpa_scan_res_match already checks that the SSID matches
current_ssid. Therefore there is no need to do any further checking.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
It should never be NULL. In the unlikely event that it is NULL, the
logic changes slightly to reject all candidates.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
When accepting a BSS transition request there is a race between
sending the response and roaming to the target AP. As a result,
the response may not be sent because the station deauthenticated
from the AP before the response was actually sent.
To make sure the BSS transition response is sent, start roaming only
after the TX status is received for the BSS transition response.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
It does not make sense to scan for neighbors that we are not supposed to
use anyway. As such, skip them.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
When receiving a BTM request, wpa_supplicant would try to fetch new
results from the driver, and, independently of that, would also process
the latest scan results that were partially updated by the previous
fetch.
Simplify the logic by using wpa_supplicant_get_scan_results() directly
and then process the old scan data as usual. However, this data may be
outdated, so add a new heuristic to avoid roaming to a BSS if it is
either outdated or bad.
Doing this moves all scan data processing into wnm_scan_process() and
removes duplicated functionality for scan result processing in scan.c.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Avoid potential race conditions with the driver operations between
stopping an ongoing wait for responses for an offchannel TX that was
used to send Authentication Request with a request to use a different
channel for Authentication Response and the start of a new ROC on the
other channel by waiting for the TX expiration event before issuing the
ROC request.
Signed-off-by: Jouni Malinen <j@w1.fi>
Avoid potential race conditions with the driver operations between
cancelling an ongoing ROC that was used to receive Authentication
Request that requested a different channel to be used for the
negotiation by waiting for the ROC cancelled event before issuing the
offchannel TX command for the Authentication Response.
In addition, speed up the retry on Authentication Response in this type
of a case if the first attempt on the other channel is not AKC'ed since
it might take the peer device a bit more time to be ready to listen
there.
Signed-off-by: Jouni Malinen <j@w1.fi>
This aligns both the wpa_supplicant and bss structures to use the same
pattern of a valid_links bitmask plus per-link entries.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
This was done using the below semantic patch. There are a few more
places that were missed due to variable declarations or additional
checks in the for loop.
@@
iterator name for_each_link;
identifier max_links =~ "MAX_NUM_MLD_LINKS|MAX_NUM_MLO_LINKS";
expression links;
expression further_tests;
identifier i;
statement stmt;
@@
-for (i = 0; i < max_links; i++)
+for_each_link(links, i)
{
(
- if (!(links & BIT(i)))
- continue;
...
|
- if (!(links & BIT(i)) || further_tests)
+ if (further_tests)
continue;
...
|
- if (further_tests || !(links & BIT(i)))
+ if (further_tests)
continue;
...
|
- if (links & BIT(i))
stmt
|
- if (further_tests && (links & BIT(i)))
+ if (further_tests)
stmt
|
- if ((links & BIT(i)) && further_tests)
+ if (further_tests)
stmt
)
}
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
When a device supports both the 5 GHz band and the 6 GHz band,
these are reported as two separate modes, both with mode set to
HOSTAPD_MODE_IEEE80211A. However, as these are different modes,
each with its own characteristics, e.g., rates, capabilities etc.,
specifically differentiate between them by adding a flag to indicate
whether the mode describes a 6 GHz band capabilities or not.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
When wpa_supplicant assigns the IP address (WFA EAPOL IP address
allocation feature), the assigned IP address of the P2P Client on the GO
side is notified in the AP-STA-CONNECTED event. So to obtain the IP info
to external programs, modify the STA authorized event to include the the
assigned IP address of the P2P Client.
Test: Establish P2P connection and verified from the logs that
the P2P Client IP address is notified.
Signed-off-by: Sunil Ravi <sunilravi@google.com>
When wpa_supplicant receives a request to start a P2P group owner on a
fixed frequency with bandwidth wider than 20 MHz, wpa_supplicant scans
for neighboring BSSs prior to starting the GO. This is done to switch
the primary/secondary channels if there are any other networks which are
operating on the same secondary channel. Though this logic is defined
for 20/40 MHz coexistence and might improve throughput, there are P2P
use cases where this logic causes problem:
1. The file transfer use case takes time to start the file transfer or
even fails when the 20/40 coex scan repeatedly fails due to an
ongoing externally triggered scan happening in the system.
2. wpa_supplicant overrides the channel which is selected by the
application based on the best channel it derived by looking into
the channel conditions. This degrades the expected throughput.
3. Latency sensitive applications experience long time to
start the group owner which gives a bad user experience.
So do not allow 40 MHz co-ex PRI/SEC switch to force a change to
Autonomous GO PRI channel when the P2P group add is called with a forced
frequency.
Test: Tested autonomous GO and confirmed from the logs that
P2P GO is not triggering 20/40 coex scan.
Signed-off-by: Sunil Ravi <sunilravi@google.com>
This adds initial parts for RADIUS/TLS support in the RADIUS client.
This can be used with eapol_test and hostapd. This functionality is not
included by default and CONFIG_RADIUS_TLS=y in .config can be used to
enable it.
This version does not yet include all the needed functionality for TLS
validation and the rules for dropping a TCP connection based on invalid
RADIUS attributes.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add hostapd support for interacting with the NAN discovery engine to
allow single-channel (i.e., the AP's operating channel) USD as Publisher
or Subscriber.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add wpa_supplicant support for interacting with the NAN discovery engine
to allow USD as Publisher or Subscriber.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The standard is somewhat unclear on whether the PMKIDs used in
(Re)Association Request frame (i.e., potential PMKIDs that could be used
for PMKSA caching during the initial mobility domain association) are to
be retained or removed when generating EAPOL-Key msg 2/4.
wpa_supplicant has replaced the PMKID List contents from (Re)Association
Request frame with PMKR1Name when generating EAPOL-Key msg 2/4 for FT.
Allow it to be configured (ft_prepend_pmkid=1) to prepend the PMKR1Name
without removing the PMKIDs from (Re)Association Request frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_supplicant disables BTM capability in Extended Capabilities element
when wpa_supplicant selects a misbehaving MBO/OCE AP that uses RSN
without PMF, but this is disabling BTM support for whole ESS connection
lifetime though the BTM support can be enabled when the driver takes
care of BSS selection and selects/roams to a BSS which is MBO and OCE
specification compliant. Thus, always set the actual BTM capability in
Extended Capabilities element when the driver takes care of BSS
selection.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
The previous os_strncmp() calls have already verified that there is a
space in the string, so this os_strchr() call cannot really return NULL.
Anyway, make this easier for static analyzers to understand.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
put_changed_properties() might fail, e.g., due to memory allocation
failure or a failure in a property getter function. Such an error case
would have leaked the message iteration container since the call to
dbus_message_iter_close_container() would have been skipped.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
