Change the nl80211 driver in wpa_supplicant to correctly handle
connecting to a new AP through cfg80211 without SME capability. As
before, the driver will disconnect from the previously associated AP,
but now we attempt to immediately connect to our intended AP. This
prevents us from blacklisting the AP we were trying to connect to
because of a semantic mismatch between cfg80211 and wpa_supplicant. The
disconnect/connect patch generates a local disconnect nl80211 event
which we discard because we're already correctly tracking the pending
association request.
In detail:
cfg80211 does not support connecting to a new BSS while already
connected to another BSS, if the underlying driver doesn't support
separate authenticate and associate commands. wpa_supplicant is written
to expect that this is a supported operation, except for a little error
handling that disconnects from the current BSS when roaming fails and
relies on autoconnect logic to reconnect later. However, this failure to
connect is incorrectly attributed to the new AP we attempted to
associate with, rather than a local condition in cfg80211.
The combined effect of these two conditions is that full-mac drivers
accessible through cfg80211 but without SME capability take a long time
to roam across BSS's because wpa_supplicant will:
1) Fail to associate for local reasons
2) Disconnect and return that the association request failed
3) Blacklist the association target (incorrectly)
4) Do a scan
5) Pick a less desirable AP to associate with
Signed-hostap: Christoper Wiley <wiley@chromium.org>
This uses the recent cfg80211 changes to allow SAE authentication to be
implemented with the nl80211 driver interface.
Signed-hostap: Jouni Malinen <j@w1.fi>
These values are used with WAPI and CCX and reserving the definitions
here reduces the number of merge conflicts with repositories that
include these functions.
Signed-hostap: Jouni Malinen <j@w1.fi>
This avoids extra latency caused by establishing an aggregation session
and makes the initial connection attempt more reliable
Signed-hostap: Felix Fietkau <nbd@openwrt.org>
This patch fixes an issue where removing a WDS VLAN interface also
removed the main AP interface from the same bridge.
Signed-hostap: Felix Fietkau <nbd@openwrt.org>
This driver_op can now be used in station mode, too, to fetch
information about the connection with the AP, so allow this to be used
even if wpa_supplicant is built without AP mode support.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows both hostapd and wpa_supplicant to be used to derive and
configure keys for GCMP. This is quite similar to CCMP key
configuration, but a different cipher suite and somewhat different rules
are used in cipher selection. It should be noted that GCMP is not
included in default parameters at least for now, so explicit
pairwise/group configuration is needed to enable it. This may change in
the future to allow GCMP to be selected automatically in cases where
CCMP could have been used.
This commit does not included changes to WPS or P2P to allow GCMP to be
used.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use the NL80211_IFACE_COMB_NUM_CHANNELS value > 1 as a trigger for
enabling support for P2P multichannel channel concurrency. This does not
handle all possible details of enforcing driver capabilities, but it is
a good first step for allowing nl80211 drivers to enable multichannel
concurrency.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit a11241fa11 removed the 802.11b rate
enabling/disabling code from wpa_driver_nl80211_set_mode() and while
doing that, removed the only place where drv->disabled_11b_rates was
set. Fix this by updating the flag in nl80211_disable_11b_rates(). In
addition, re-enable the 802.11b rates when changing to non-P2P mode.
Signed-hostap: Jouni Malinen <j@w1.fi>
Right now 11b rates are masked out while creating a P2P interface,
but this is always failing as the interface is down. Most drivers
allow to configure rates only when the interface is UP and running.
So let us disable 11b rates when interface type is changed into a
P2P type and it is UP and running.
Signed-hostap: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Couple of functions did not verify that nla_put_nested() succeeded. Fix
these by checking the return value and handling error cases cleanly.
Signed-hostap: Jouni Malinen <j@w1.fi>
Allow the user to configure an RSSI threshold in dBm below which the
nl80211 driver won't report scan results. Currently only supported
during scheduled (PNO) scans.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Some drivers may independently decide to switch channels. Handle this by
updating the hostapd and wpa_supplicant AP and GO configuration.
Signed-hostap: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
The control message received from the kernel needs some space, but
there's no need for the strange typing that breaks clang compilation.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
In certain cases like PBC session overlap it appears to be possible that
an interface is removed due to an event handled on it, this leads to
list corruption. Use safe iteration to prevent this issue.
Reported-by: Nirav Shah <nirav.j2.shah@intel.com>
Reported-by: Neeraj Kumar Garg <neerajkg@broadcom.com>
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
intended-for: hostap-1
When sending an offchannel frame (mainly, P2P Invitation Request), the
wait_time parameter was hardcoded to 0 for drivers that implement AP
mode SME. This is not correct and can cause problems for drivers that
support offloading of off-channel operations with driver/firmware based
AP SME.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to subscribe to event messages during deinit process,
so skip this to avoid unnecessary operations and to keep the debug logs
a bit cleaner.
Signed-hostap: Jouni Malinen <j@w1.fi>
This was previously indicated as disassociation, but the P2P group
session ending case expect a deauthentication notification. Since the
cfg80211 disconnection event does not really indicate which frame was
used, the easiest approach for now seems to be to just indicate these
as deauthentication events.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
On P2P group removal, the GO is deinitialized correctly (and the vif
mode is set back to sta in case of nl80211), but the P2P client mode
wasn't deinitialized, and the nl80211 vif stays in P2P client mode.
Add a new deinit_p2p_cli op (similar to deinit_ap), which currently only
sets the interface back to station mode.
Signed-hostap: Eliad Peller <eliad@wizery.com>
intended-for: hostap-1
The signal strength is currently never used as the only driver reporting
it is nl80211 which uses IEEE80211_RADIOTAP_DB_ANTSIGNAL which is never
populated by the kernel. The kernel will (soon) populate
IEEE80211_RADIOTAP_DBM_ANTSIGNAL instead though, so use that.
Also, since it was never really populated, we can redefine the signal
field to be in dBm units only.
My next patch will also require knowing the signal strength of probe
requests throughout the code (where available), so add it to the
necessary APIs.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
A network block specific background scan period can now be configured
for drivers that implement internal background scan mechanism for
roaming and BSS selection.
Signed-hostap: Bala Shanmugam <bkamatch@qca.qualcomm.com>
When drivers advertise their capability to free up inactive
stations based on ap_max_inactivity, send the inactivity period
timeout to driver in NL80211_ATTR_INACTIVITY_TIMEOUT. This
introduces a WPA_DRIVER_FLAGS (WPA_DRIVER_FLAGS_INACTIVITY_TIMER)
so that the inactivity period will be sent only when this capability
bit is set.
Signed-hostap: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
When the driver (or firmware) implements AP mode SME, the use of raw
management frame TX functions is not working properly at the moment. As
an initial step, convert these AP mode operations to use
NL80211_CMD_DEL_STATION and do not claim that driver provides TX status
for deauth/disassoc frames. While this does not address all use cases
(e.g., reason code is not specified in the command), this fixes number
of issues where the station does not get disconnected properly.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like a RTM_NEWLINK event claiming the interface to be UP is
delivered just before removing an interface after having first indicated
that the interface was going down/removed. Ignore this event if the
interface is not present anymore at the moment the event is processed.
This fixes issues where an interface that was re-added after being
removed did not get reconfigured properly.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
In IBSS RSN cfg80211/mac80211 now waits for userspace to authorize new
stations. This patch makes wpa_supplicant notify the driver when a
station can be considered authorized.
Signed-hostap: Antonio Quartulli <ordex@autistici.org>
This allows HT capabilities overrides on kernels that
support these features.
MCS Rates can be disabled to force to slower speeds when using HT.
Rates cannot be forced higher.
HT can be disabled, forcing an 802.11a/b/g/n station to act like
an 802.11a/b/g station.
HT40 can be disabled.
MAX A-MSDU can be disabled.
A-MPDU Factor and A-MPDU Density can be modified.
Please note that these are suggestions to the kernel. Only mac80211
drivers will work at all. The A-MPDU Factor can only be decreased and
the A-MPDU Density can only be increased currently.
Signed-hostap: Ben Greear <greearb@candelatech.com>
In multiple BSSes scenario for the drivers that do not use
monitor interface and do not implement AP SME, RX MGMT
frame subscription happens only for the default bss (first_bss).
Subscribe for RX MGMT frames for such BSSes.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Commit e4fb216769 moved frequency
storage from driver struct to bss struct and is assigned in
wpa_driver_nl80211_set_freq. As this wpa_driver_nl80211_set_freq is
triggered only on the first_bss, bss->freq for other BSSes is never
being set to the correct value. This sends MLME frames on frequency zero
(initialized value of freq) for BSSes other than the first.
To fix this derive frequency value from first_bss.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
A P2P Action frame may need to be sent on another channel than the GO's
operating channel. This information was lost in
wpa_driver_nl80211_send_action() in the case the interface was in AP
mode. Pass the frequence and related parameters to send_mlme mechanism
to allow the correct frequence to be used with the send frame command in
AP (P2P GO) mode.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The cookie value needs to be fetched in GO mode, too, to be able to
indicate TX status callbacks with drivers that handle AP mode SME
functionality internally. This fixes issues with client discoverability
where TX status callback for GO Discoverability Request is needed to
trigger the GO to send Device Discoverability Response.
The deauthentication and disassociation events from nl80211 were being
processed identically regardless of whether the frame was generated by
the local STA or the AP. This resulted in fast reconnection mechanism
getting triggered even in the case where the disconnection was detected
locally (e.g., due to beacon loss) while this was supposed to happen
only in the case where the AP is sending an explicit Deauthentication
or Disassociation frame with a specific reason code.
Fix this by adding a new deauth/disassoc event variable to indicate
whether the event was generated locally.
Signed-hostap: Jouni Malinen <j@w1.fi>
The offchanok parameter is hardcoded to one in number of paths and that
added NL80211_ATTR_OFFCHANNEL_TX_OK attribute to NL80211_CMD_FRAME
unconditional. cfg80211 rejects this with EINVAL if the driver does not
indicate support for offchannel TX. Fix this by not requesting
offchannel TX depending on driver capabilities. Remain-on-channel
operation was used for those cases anyway, so the additional attribute
was not really needed for these in the first place.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When nl80211_setup_ap() has enabled Probe Request reporting, this must
not be disabled when P2P Listen state is stopped to avoid breaking AP
mode operations. This could happen, e.g., if a Probe Request frame was
received from a P2P device that the we are trying to invite to our group
(i.e., when operating in GO role). p2p_probe_req_rx() calls
p2p_invite_start() in this case and that ends up calling
p2p->cfg->stop_listen() which calls probe_req_report() driver op.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Drivers that use device SME in AP mode may still need to be
subscribed for Action frame RX when monitor interface is not used.
This fixes number of P2P GO operations with ath6kl.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Poll command may be enough for mac80211 to figure out whether monitor
interface is to be used, but this change did not take into account
non-mac80211 drivers that support AP mode without monitor interface.
For example, ath6kl needs to get use_monitor disabled.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Android ICS system/core/libnl_2 has very limited genl_ctrl_resolve()
implementation that cannot handle names other than nlctrl. Work
around that by implementing more complete genl_ctrl_resolve()
functionality within driver_nl80211.c for Android builds.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This updates a previous patch did more or less the same thing by
providing the qosinfo as a single variable to the driver wrappers.
Signed-hostap: Jason Young <jason.young@dspg.com>
Check whether the driver advertises support for U-APSD
in AP mode, and evaluate wmm_uapsd only in this case.
Signed-off-by: Eliad Peller <eliad@wizery.com>
The wpa_hexdump_ascii() call did not get converted properly and this
was missed becaused of it getting defined out from the build. Anyway,
this better use the correct variable names should that debug print
ever be enabled for Android.
Signed-hostap: Jouni Malinen <j@w1.fi>
Pass the raw Probe Response template to kernel via netlink using the
set_ap() driver callback. The data is sent as one of the Beacon
attributes.
Signed-hostap: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Translate nl80211 flags to wpa_supplicant flags for Probe Response
offload support. The existence of the nl80211 PROBE_RESP_OFFLOAD_SUPPORT
attribute means Probe Response offload is supported. The value of the
attribute is a bitmap of supported protocols.
Signed-hostap: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Storing the address in the BSS instead of the DRV struct makes it usable
for hostapd and thus gets rid of the linux_get_ifhwaddr() call when
receiving a spurious frame.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Since the nl_cache is not used anymore, there is no need for maintaining
the struct nl80211_handles wrapper for struct nl_handle. Clean this up
by using nl_handle directly.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is a rewrite of Ben Greear's patch, making the
nl80211 code use just a single multicast event socket.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
When running AP mode, we need to receive beacons over overlapping BSSes
to handle protection. Use the new nl80211 command for this. As the
command works per wiphy (and we don't want to receive the Beacon frames
multiple times) add an abstraction that keeps track of per-wiphy data.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
These events are necessary to send deauth frames to
stations sending spurious data frames. Subscribe to
them on the per-BSS event socket.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
To achieve this, multiple things are needed:
1) since hostapd needs to handle *all* action frames,
make the normal registration only when in a non-AP
mode, to be able to do this use the new socket
2) store the frequency in each BSS to be able to give
the right frequency to nl80211's mgmt-tx operation
3) make TX status processing reject non-matched cookie
only in non-AP mode
The whole thing depends on having station-poll support
in the kernel. That's currently a good indicator since
the kernel patches are added together.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
When using authentication retry within driver_nl80211.c, a failure on the
second attempt has to be indicated with a driver event since the return
code from wpa_driver_nl80211_authenticate() is not actually delivered to
the core code in that case.
Signed-hostap: Jouni Malinen <j@w1.fi>
cfg80211 rejects NL80211_CMD_AUTHENTICATE with ENOENT if the BSS entry
for the target BSS is not available. This can happen if the cfg80211
entry has expired before wpa_supplicant entry (e.g., during a suspend).
To recover from this quickly, run a single channel scan to get the
cfg80211 entry back and then retry authentication command again. This
is handled within driver_nl80211.c to keep the core wpa_supplicant
implementation cleaner.
Signed-hostap: Jouni Malinen <j@w1.fi>
Set the NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT flag for nl80211 to tell
drivers (mac80211) to not encrypt the EAPOL frames for WEP IEEE 802.1X.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
In preparation for things that receive on a BSS-specific handle,
allocate a CB for it and hook it up to receive functions.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The next patch will add process_bss_event, rename process_event to
process_drv_event to differentiate between them.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
By passing the nl_cb as the context to the eloop function we can
(in the next patch) use the same eloop function for BSS events.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Storing the frequency in the bss struct allows using it for frame
commands in AP mode and not relying on the driver struct as much, which
is good for hostapd mode.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This will allow getting TX status for EAPOL frames
sent as data frames if the driver supports it.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The RTM_NEWLINK even can have IFF_UP flag even if the interface is
down. Do not generate EVENT_INTERFACE_ENABLED event based on such a
message.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is based on the Android driver_cmd changes that are converted to
use the sched_scan/stop_sched_scan driver_ops for the case where the
driver does not support the new nl80211 commands.
Change-Id: Iaedc340f84650af422bd2ea57d2a8b0a9d4a5330
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
cfg80211 will reject the NL80211_CMD_START_SCHED_SCAN if too many
match sets are requested. To avoid being completely unable to start
any scheduled scans, skip setting these filters if the driver did
not advertise support for large enough number of match sets.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds initial implementation of set_p2p_powersave to allow legacy PS
mode to be configured. P2P PS parameters are not yet supported.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It's not really valid to send off-channel in all cases,
so pass whether it should be allowed or not and don't
set it in the AP case.
Also, to get the right ifindex for hostapd, pass a bss
pointer instead of the drv pointer.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
In some situations it might be benefical to send a unicast frame without
the need for getting it ACKed (probe responses for example). In order to
achieve this add a new noack parameter to the drivers send_mlme callback
that can be used to advise the driver to not wait for an ACK for this
frame.
Signed-hostap: Helmut Schaa <helmut.schaa@googlemail.com>
If the kernel supports this, don't use manual null
data frame transmissions. This is one thing to get
rid of cooked monitor interfaces.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
