It was possible for a timeout from an old GAS server operation to
trigger DPP configuration failure during the subsequent DPP operation.
Fix this by verifying that the status callback is for the response
generated during the same DPP Authentication/Configuration exchange.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Configurator signing its own Connector was previously supported only in
wpa_supplicant. This commit extends that to hostapd to allow an AP
acting as a Configurator to self-configure itself.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previous implementation did not handle number of sequences correctly.
Make sure the iteration continues in both unicast and broadcast cases
until the five attempts have been made. In addition, improve timing by
checking 10 second time from the beginning of each iteration round and
not the last channel on which the Auth Req frame has been transmitted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the Authentication Request frame was retried after 2+10 = 12
seconds since the wait for the response was not accounted for. Substract
that wait from the 10 second wait time to start the retries more quickly
based on the 10 second timer described in the tech spec.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If unicast Authentication Request frame is used and the peer ACKs such a
frame, but does not reply within the two second limit, there is no need
to continue trying to retransmit the request frames since the peer was
found, but not responsive.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new conf={sta,ap}-{sae,psk-sae} parameter values can now be used to
specify that the legacy configuration object is for SAE.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows DPP to be used for enrolling credentials for SAE networks in
addition to the legacy PSK (WPA-PSK) case. In addition, enable FT-PSK
and FT-SAE cases automatically.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Retransmit the PKEX Exchange Request frame if no response from a peer is
received. This makes the exchange more robust since this frame is sent
to a broadcast address and has no link layer retries.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend dpp_test to allow more invalid attribute values to be written
into Peer Discovery Request/Response frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend dpp_test to cover a case where Config Attrib Object value is
invalid in Configuration Request frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends wpa_supplicant DPP implementation to retransmit DPP
Authentication Response frame every 10 seconds up to 5 times if the peer
does not reply with DPP Authentication Confirm frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, this command stopped listen operation immediately, but if
there was an ongoing authentication exchange, a new listen operation was
started. This is not really expected behavior, so stop the
authentication exchange first with this command to avoid restarting
listen operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new role=either parameter can now be used with DPP_AUTH_INIT to
indicate that the initiator can take either the Configurator or Enrollee
role.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends wpa_supplicant to iterate over all available channels from
the intersection of what the peer indicates and the local device
supports when initiating DPP Authentication. In addition, retry DPP
Authentication Request frame up to five times if no response is
received.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Generate the PKEX bootstrapping information and release the PKEX session
in a helper function that both the initiator and responder can use
instead of maintaining this functionality separately in two places.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add limit on number of failed attempts that could have used PKEX code.
If the limit (5) is reached, drop the PKEX state (including the code)
and report this on the control interface to indicate that a new code
needs to be entered due to possible attack.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Clean up the pending PKEX exchange if Commit-Reveal Request processing
indicates a mismatch in the PKEX code. Previously, the this case was
silently ignored and the session was left in pending state that
prevented new PKEX exchanges from getting initated. Now, a new attempt
is allowed to be initiated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Report mismatching finite cyclic group with PKEX Exchange Response using
STATUS_BAD_GROUP and provide more detailed error report over the control
interface on the peer device when this happens.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Indicate to upper layers if PKEX Commit-Reveal Request frame AES-SIV
decryption fails. That is a likely sign of the PKEX code mismatch
between the devices.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
DPP AKM should really require PMF to be used, but since that is not yet
explicitly required in the specification, make PMF enabled for now. For
legacy PSK cases, configure PMF to be enabled as well to support both
APs in no-PMF, optional-PMF, and required-PMF configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow the Initiator to request a different channel to be used for DPP
Authentication and DPP Configuration exchanges. This commit adds support
for this in wpa_supplicant with the optional neg_freq=<freq in MHz>
parameter in DPP_AUTH_INIT.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is useful for protocol testing purposes and UI needs to display
more detailed information about DPP exchanges.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is helpful for testing purposes and also for upper layer components
that may want to show more detailed progress through a DPP exchange.
Both the DPP-TX and DPP-TX-STATUS events are provided.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is helpful for testing purposes and also for upper layer components
that may want to show more detailed progress through a DPP exchange.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Now that dpp_check_attrs() takes care of verifying that no attributes
are after the Wrapped Data attribute, the duplicated checks in hostapd
and wpa_supplicant side of the implementation can be removed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This additional field was added to DPP Public Action frames in DPP tech
spec v0.2.3 to support cryptographic agility in the future.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new psk=<hexdump> can be used as an alternative to pass=<passphrase>
when configuring the DPP Configurator with a legacy network parameters.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
DPP tech spec changed the contents of these frames by replacing the
public key hash attributes with a Transaction ID attribute that gets
copied from the request to the response to identify the transaction in a
simpler manner.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The DPP Configurator can use this new command to generate its own signed
connector for the network that it manages.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows wpa_supplicant to be configured to act as the configurator
in the case where a peer device initiates DPP Authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This implements genric PKEX functionality in src/common/dpp.c and glue
code to use this in wpa_supplicant (i.e, hostapd DPP implementation does
not yet support PKEX).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new pass=<hexdump> parameter to DPP_AUTH_INIT can now be used to
specify the passphrase to use in config object.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new ssid=<hexdump> parameter to DPP_AUTH_INIT can now be used to
specify the SSID to use in config object.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant can now be configured to generate a network profile
automatically based on DPP configuration. The following
dpp_config_processing values can be used to specify the behavior:
0 = report received configuration to an external program for
processing; do not generate any network profile internally (default)
1 = report received configuration to an external program and generate
a network profile internally, but do not automatically connect
to the created (disabled) profile; the network profile id is
reported to external programs
2 = report received configuration to an external program, generate
a network profile internally, try to connect to the created
profile automatically
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds support for DPP Configuration Protocol using GAS. Full
generation and processing of the configuration object is not included in
this commit.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add wpa_supplicant control interface commands for parsing the bootstrap
info URI from a QR Code (get peer public key) and to generate a new
bootstrap info with private key for local use. The optional
key=<hexdump> argument to the DPP_BOOTSTRAP_GEN command can be used to
specify the bootstrapping private key in OpenSSL ECPrivateKey DER
encoding format. This results in the local bootstrapping information
entry being created with the specified key instead of generating a new
random one.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
