After successfully passing the 525 tests on a remote setup mark the
tests as remote compatible.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
The hwsim tests used to execute shell commands in the tests using the
subprocess python module. Use the cmd_execute() general function for
executing shell commands to setup bridge so that this would also work on
remote setups.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
The hwsim tests used to execute shell commands in the tests using the
subprocess python module. Use the cmd_execute() general function for
executing "ip link set up/down" commands so that this would also work on
remote setups.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
The hwsim tests used to execute shell commands in the tests using the
subprocess python module. Use the cmd_execute() general function for
executing "ps ax" so that this would also work on remote setups.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
Pass the full apdev to the add_ap() function instead of just ifname.
This allows us to handle also remote hosts while we can check
apdev['hostname'], apdev['port'].
This step (7) converts the cases where a local variable is used to store
apdev[#]['ifname'] before passing it as the argument to hostapd.add_ap().
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Pass the full apdev to the add_ap() function instead of just ifname.
This allows us to handle also remote hosts while we can check
apdev['hostname'], apdev['port'].
This step (4) converts the cases that call hostapd.add_ap() from a
helper function that got apdev[i] as an argument.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Pass the full apdev to the add_ap() function instead of just ifname.
This allows us to handle also remote hosts while we can check
apdev['hostname'], apdev['port'].
This step (1) converts the cases where apdev[#]['ifname'] was used as
the argument to hostapd.add_ap().
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
The decrypted copy of a GTK from EAPOL-Key is cleared from memory only
after having sent out CTRL-EVENT-CONNECTED. As such, there was a race
condition on the test case reading the wpa_supplicant process memory
after the connection. This was unlikely to occur due to the one second
sleep, but even with that, it would be at least theorically possible to
hit this race under heavy load (e.g., when using large number of VMs to
run parallel testing). Avoid this by running a PING command to make sure
wpa_supplicant has returned to eloop before reading the process memory.
This should make it less likely to report false positives on GTK being
found in memory.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to see where in memory the key was found and what
there is in memory around that location.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like it is possible for the GTK to be found from memory every
now and then. This makes these test cases fail. Write the memory
addresses in which the GTK was found to the log to make it somewhat
easier to try to figure out where the key can be left in memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
Set the bridge ageing to 1 sec to make the bridge clear unused
addresses after this interval. Otherwise the test depends on
the local configuration of brctl.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
These test cases left at least one of the attached monitor sockets
blocking for excessive time: ap_wpa2_eap_aka_ext,
ap_hs20_req_conn_capab_and_roaming_partner_preference,
ap_hs20_min_bandwidth_and_roaming_partner_preference, ap_wpa_ie_parsing.
Signed-off-by: Jouni Malinen <j@w1.fi>
Number of test cases did not read all control interface socket events
from the dynamically added wlan5 interface. This could result in hitting
maximum socket TX queue length and failures in the following test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
When the 'SET wpa 2' command is executed last, it seems to somehow
reset parts of the settings, causing hostapd to beacon with the
pairwise cipher suite selector set to 00-0F-AC:0 (none/use-group).
This is not permitted and should be rejected; wpa_supplicant also
cannot connect.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to a copy-paste error, these test cases left 4addr mode enabled on
wlan5. This resulted in number of connect_cmd_* test cases failing if
executed after the wpas_in_bridge tests.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
run-tests.py is running as root, so sudo does not need to be used
anymore from within each test case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The test used p2p_dev_addr() that can be different from own_addr()
if a dedicated P2P Device interface is used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
It was possible for the GTK-found-in-memory case to be triggered due to
a retransmission of EAPOL-Key msg 3/4 especially when running test cases
under heavy load (i.e., timeout on hostapd due to not receiving the 4/4
response quickly enough). Make this false failure report less likely by
waiting a bit longer after the connection has been completed before
fetching the process memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of returning "skip" from the test function, raise the new
HwsimSkip exception to indicate a test case was skipped.
Signed-off-by: Jouni Malinen <j@w1.fi>
This implements minimal RSN 4-way handshake Supplicant in Python and
uses that to test hostapd Authenticator implementation in various
possible protocol sequencies.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to replace data connectivity testing to use
something else than local hwsim_test binary on the controller device.
Signed-off-by: Jouni Malinen <j@w1.fi>
These are similar to the existing test cases where PTK rekey was
triggered by the station, but here a timer on the AP is used as the
trigger.
Signed-off-by: Jouni Malinen <j@w1.fi>
Only run-tests.py is actually executed, so there is no need to specify
the interpreter in all the helper files and test script files.
Signed-off-by: Jouni Malinen <j@w1.fi>
