Include an OCI element in SA Query Request and Response frames if OCV
has been negotiated.
On Linux, a kernel patch is needed to let clients correctly handle SA
Query Requests that contain an OCI element. Without this patch, the
kernel will reply to the SA Query Request itself, without verifying the
included OCI. Additionally, the SA Query Response sent by the kernel
will not include an OCI element. The correct operation of the AP does
not require a kernel patch.
Without the corresponding kernel patch, SA Query Requests sent by the
client are still valid, meaning they do include an OCI element.
Note that an AP does not require any kernel patches. In other words, SA
Query frames sent and received by the AP are properly handled, even
without a kernel patch.
As a result, the kernel patch is only required to make the client properly
process and respond to a SA Query Request from the AP. Without this
patch, the client will send a SA Query Response without an OCI element,
causing the AP to silently ignore the response and eventually disconnect
the client from the network if OCV has been negotiated to be used.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
This adds two utility functions to convert both operating classes and
and the chan_width enum to an integer representing the channel
bandwidth. This can then be used to compare bandwidth parameters in an
uniform manner.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
This adds driver API functions to get the current operating channel
parameters. This encompasses the center frequency, channel bandwidth,
frequency segment 1 index (for 80+80 channels), and so on.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
Some mac80211_hwsim test cases have failed with mysterious sequence
where mac80211 has claimed the parameters are invalid ("wlan3: invalid
CW_min/CW_max: 9484/40"). Those values look strange since they are not
from hostapd configuration or default values.. hostapd is seeing TX
queue parameter set failing for queues 0, 1, and 3 (but not 2) for these
cases. Add debug prints to hostapd to get more details on what exactly
is happening if such error cases can be reproduced.
Signed-off-by: Jouni Malinen <j@w1.fi>
The currently unused conf_offset parameter used a mismatching type (enum
vs. unsigned int) compared to the prototype.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When external authentication is used, a specific netlink socket is used
to send the connect command. If the same socket is not used for
disconnect command, cfg80211 will discard the command. This constraint
was added into the kernel in commit bad292973363 ("nl80211: Reject
disconnect commands except from conn_owner"). That requires an update
for the hostap.git commit 40a68f3384 ("nl80211: Create a netlink
socket handle for the Connect interface").
Add a new flag into struct i802_bss to indicate if the special
nl_connect socket was used for the connect command. When sending
disconnect command this flag is tested to select the correct socket.
Signed-off-by: Cedric Izoard <cedric.izoard@ceva-dsp.com>
Add documentation to the wpa_signal_info structure.
Add a define for an invalid noise value.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Back in December 2017, Jouni fixed the output side since that was
causing a kernel message to be printed, but the input side should
also be fixed, otherwise it will not work correctly on big-endian
platforms.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for negotiating WNM Collocated Interference Reporting. This
allows hostapd to request associated STAs to report their collocated
interference information and wpa_supplicant to process such request and
reporting. The actual values (Collocated Interference Report Elements)
are out of scope of hostapd and wpa_supplicant, i.e., external
components are expected to generated and process these.
For hostapd/AP, this mechanism is enabled by setting
coloc_intf_reporting=1 in configuration. STAs are requested to perform
reporting with "COLOC_INTF_REQ <addr> <Automatic Report Enabled> <Report
Timeout>" control interface command. The received reports are indicated
as control interface events "COLOC-INTF-REPORT <addr> <dialog token>
<hexdump of report elements>".
For wpa_supplicant/STA, this mechanism is enabled by setting
coloc_intf_reporting=1 in configuration and setting Collocated
Interference Report Elements as a hexdump with "SET coloc_intf_elems
<hexdump>" control interface command. The hexdump can contain one or
more Collocated Interference Report Elements (each including the
information element header). For additional testing purposes, received
requests are reported with "COLOC-INTF-REQ <dialog token> <automatic
report enabled> <report timeout>" control interface events and
unsolicited reports can be sent with "COLOC_INTF_REPORT <hexdump>".
This commit adds support for reporting changes in the collocated
interference (Automatic Report Enabled == 1 and partial 3), but not for
periodic reports (2 and other part of 3).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If driver supports self-managed regulatory domain, read reg-domain
information for that specific wiphy interface instead the global
information which may be different which such drivers. This fixes issues
where a regulatory update with a self-managed regulatory domain driver
ended up building incorrect list of supported channels for upper layer
hostapd/wpa_supplicant operations.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a flag indicating if the device has the self-managed regulatory
support. Set the flag if NL80211_ATTR_WIPHY_SELF_MANAGED_REG attribute
is set when reading wiphy info.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is something useful to know and also eliminates format truncation
warnings.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Check if the device supports specific mandatory features and set the the
relevant WPA_DRIVER_FLAGS_OCE_STA flag. Send the relevant scan
parameters for OCE scans.
Signed-off-by: Roee Zamir <roee.zamir@intel.com>
Add a flag to scan parameters that enables OCE scan features. If this
flag is set the device should enable the following features as defined
in the Optimized Connectivity Experience Technical Specification v1.0:
- Overwrite FILS request Max Channel Time with actual value (clause 3.8)
- Send Probe Request frame in high rate (at least 5.5 Mbps) (clause 3.12)
- Probe Request frame Transmission Deferral and Suppression (clause 3.5)
- Accept broadcast Probe Response frame (clause 3.6)
Signed-off-by: Roee Zamir <roee.zamir@intel.com>
Commit 3f53c006c7 ('nl80211: Ignore
disconnect event in case of locally generated request') made
wpa_supplicant ignore the next received disconnect event for cases where
wpa_supplicant itself requested a disconnection. This can result in
ignoring a disconnection notification in some cases.
Considering a P2P Client receiving disconnect event from the kernel
after a P2P group is started, drv->ignore_next_local_disconnect is
cleared to 0, then wpa_driver_nl80211_disconnect() will be called during
the removal of the group, in which drv->ignore_next_local_disconnect is
set to 1 by mistake.
Do not allow ignore_next_local_{disconnect,deauth} to be set to 1 if the
driver is not in associated state (drv->associated is 0) to avoid this
type of cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The WDS-STA-INTERFACE-ADDED/WDS-STA-INTERFACE-REMOVED events were always
sent to the first BSS instead of the specific BSS that the STA was
connected to in multi-BSS cases. Fix this by using the BSS specific
context pointer.
Fixes: 1952b626ba ("hostapd: Add ctrl iface indications for WDS STA interface")
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
GCM-AES-256 cipher suite is defined in IEEE Std 802.1AEbn-2011.
If authenticator configured as GCM-AES-256, the distributed SAK will be
256 bits indicated by the GCM-AES-256 ID in the MKA packet.
This patch will make AES Key Unwrap to 32 bytes of SAK when identify the
ID.
Signed-off-by: xiaofeis <xiaofeis@codeaurora.org>
ifname is checked for interface down event in commit
106fa1e97e ("nl80211: Indicate
interface-down event only for the main netdev"). Do the same for
interface up event to avoid unexpected notifications when the master
interface (e.g., a bridge interface) is set up while then WLAN interface
remains down.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When we start hostapd having Hotspot 2.0 configuration with interface
already added to bridge interface, addition and deletion of new neighbor
to bridge ip neighbor table fails.
This is since 'bss->added_if_into_bridge' is not set which only allows
'drv->rtnl_sk' (nl_sock for NETLINK_ROUTE) allocation needed for bridge
ip neighbor table.
Add a new bit 'already_in_bridge' and set it when interface is already
added to bridge by some external component. Check this bit in addition
to 'bss->added_if_into_bridge' for 'drv->rtnl_sk' allocation done in
i802_init().
Now 'drv->rtnl_sk' is closed in wpa_driver_nl80211_deinit() regardless of
'bss->added_if_into_bridge' since when we have 'bss->already_in_bridge'
case too, this need to be removed.
brctl show
bridge name bridge id STP enabled interfaces
br0 8000.8efdf006b050 no ap
hostapd_cli raw STATUS-DRIVER
Selected interface 'ap'
ifindex=15
ifname=ap
brname=br0
addr=8e:fd:f0:06:b0:50
freq=5180
beacon_set=1
already_in_bridge=1
..
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Since the generic DFS offload support flag is added as
NL80211_EXT_FEATURE_DFS_OFFLOAD, only use the vendor command to check
DFS capablity if the flag is not already set.
Signed-off-by: Peng Xu <pxu@codeaurora.org>
Handle NL80211_CMD_WIPHY_REG_CHANGE the same way as the
NL80211_CMD_REG_CHANGE event. The wiphy-specific event is generated by
the cfg80211 reg_process_self_managed_hints() function, e.g., when going
through regulatory_set_wiphy_regd_sync_rtnl(). Previously, such events
were ignored completely in hostapd/wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
New WPA_DRIVER_FLAGS have been added but corresponding lookup
strings for driver_flags command were never added. Add the
missing strings.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sony.com>
Add mesh type to nl80211 channel switch request, so mesh is able to send
the request to kernel drivers.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
Before calling HW macsec driver API, be_to_host16() should be used to
reverse the SCI port byte order. This was broken as part of the mka API
changes.
Fixes: 8ebfc7c2ba ("mka: Pass full structures down to macsec drivers' transmit SC ops")
Signed-off-by: xiaofeis <xiaofeis@codeaurora.org>
The first two parameters to readlink() are marked restricted and at
least gcc 8.2 warns about used the same pointer for then, so avoid this
by using separate buffers for the pathname and response buffer.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allows user to get event indication when a new interface is
added/removed for 4addr WDS STA and also WDS STA ifname is informed
through the STA command.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Add WPA FT auth to connect params in case of a re-connection to ESS
supporting FT when FT was used in the first connect.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
The Linux 4.9 kernel, at least, can return EEXIST when trying to auth a
station that already exists.
We have seen this bug in multiple places, but it is difficult to
reproduce. Here is a link to someone else that appears to have hit this
issue: https://github.com/greearb/ath10k-ct/issues/18
Signed-off-by: Ben Greear <greearb@candelatech.com>
When connecting to a WPA-EAP network and the MAC address is changed
just before the association (for example by NetworkManager, which sets
a random MAC during scans), the authentication sometimes fails in the
following way ('####' logs added by me):
wpa_supplicant logs:
wlan0: WPA: RX message 1 of 4-Way Handshake from 02:00:00:00:01:00 (ver=1)
RSN: msg 1/4 key data - hexdump(len=22): dd 14 00 0f ac 04 d8 21 9d a5 73 98 88 26 ef 03 d2 ce f7 04 7d 23
WPA: PMKID in EAPOL-Key - hexdump(len=22): dd 14 00 0f ac 04 d8 21 9d a5 73 98 88 26 ef 03 d2 ce f7 04 7d 23
RSN: PMKID from Authenticator - hexdump(len=16): d8 21 9d a5 73 98 88 26 ef 03 d2 ce f7 04 7d 23
wlan0: RSN: no matching PMKID found
EAPOL: Successfully fetched key (len=32)
WPA: PMK from EAPOL state machines - hexdump(len=32): [REMOVED]
#### WPA: rsn_pmkid():
#### WPA: aa - hexdump(len=6): 02 00 00 00 01 00
#### WPA: spa - hexdump(len=6): 66 20 cf ab 8c dc
#### WPA: PMK - hexdump(len=32): b5 24 76 4f 6f 50 8c f6 a1 2e 24 b8 07 4e 9a 13 1b 94 c4 a8 1f 7e 22 d6 ed fc 7d 43 c7 77 b6 f7
#### WPA: computed PMKID - hexdump(len=16): ea 73 67 b1 8e 5f 18 43 58 24 e8 1c 47 23 87 71
RSN: Replace PMKSA entry for the current AP and any PMKSA cache entry that was based on the old PMK
nl80211: Delete PMKID for 02:00:00:00:01:00
wlan0: RSN: PMKSA cache entry free_cb: 02:00:00:00:01:00 reason=1
RSN: Added PMKSA cache entry for 02:00:00:00:01:00 network_ctx=0x5630bf85a270
nl80211: Add PMKID for 02:00:00:00:01:00
wlan0: RSN: PMKID mismatch - authentication server may have derived different MSK?!
hostapd logs:
WPA: PMK from EAPOL state machine (MSK len=64 PMK len=32)
WPA: 02:00:00:00:00:00 WPA_PTK entering state PTKSTART
wlan1: STA 02:00:00:00:00:00 WPA: sending 1/4 msg of 4-Way Handshake
#### WPA: rsn_pmkid():
#### WPA: aa - hexdump(len=6): 02 00 00 00 01 00
#### WPA: spa - hexdump(len=6): 02 00 00 00 00 00
#### WPA: PMK - hexdump(len=32): b5 24 76 4f 6f 50 8c f6 a1 2e 24 b8 07 4e 9a 13 1b 94 c4 a8 1f 7e 22 d6 ed fc 7d 43 c7 77 b6 f7
#### WPA: computed PMKID - hexdump(len=16): d8 21 9d a5 73 98 88 26 ef 03 d2 ce f7 04 7d 23
WPA: Send EAPOL(version=1 secure=0 mic=0 ack=1 install=0 pairwise=1 kde_len=22 keyidx=0 encr=0)
That's because wpa_supplicant computed the PMKID using the wrong (old)
MAC address used during the scan. wpa_supplicant updates own_addr when
the interface goes up, as the MAC can only change while the interface
is down. However, drivers don't report all interface state changes:
for example the nl80211 driver may ignore a down-up cycle if the down
message is processed later, when the interface is already up. In such
cases, wpa_supplicant (and in particular, the EAP state machine) would
continue to use the old MAC.
Add a new driver event that notifies of MAC address changes while the
interface is active.
Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
Add generic DFS offload support using the nl80211 feature that was
recently added to the mac80211-next tree. This uses the already
available DFS offload infrastructure that was previously used with
vendor specific definitions and just sets necessary flags (DFS_OFFLOAD
ext_feature) and forawrds CAC_STARTED event for processing.
Signed-off-by: Dmitry Lebed <lebed.dmitry@gmail.com>
The nl80211 driver can report STA_OPMODE notification event as soon as
it receives an HT/VHT Action frame about modification of station's SMPS
mode/bandwidth/RX NSS. Add support to parse such events.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
This allows external application to get last ACK signal strength of the
last transmitted frame if the driver makes this information
(NL80211_STA_INFO_ACK_SIGNAL) available.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Now we can configure the network block so that it allows MFP setting for
the NL80211_CMD_CONNECT command. If the kernel finds an AP that requires
MFP, it'll be able to connect to it.
Note that since NL80211_MFP_OPTIONAL isn't supported for
NL80211_CMD_ASSOCIATE, we need to take the MFP configuration outside
nl80211_connect_common(). In addition, check that
NL80211_EXT_FEATURE_MFP_OPTIONAL is supported, to be backward compatible
with older kernels.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Indicate that the connection is authorized when receiving a port
authorized event from the driver.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add an event that indicates that the 4 way handshake was completed by
the driver.
This event is useful for networks that require 802.1X authentication.
The driver can use this event that a new connection is already
authorized (e.g. when the driver used PMKSA caching) and 802.1X
authentication is not required.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add support for setting the PMK to the driver. This is used for
drivers that support 4-way handshake offload.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Set the WPA_DRIVER_FLAGS_4WAY_HANDSHAKE flag if the driver indicates
both 4-way handshake PSK and 802.1X support. Currently wpa_supplicant
doesn't distinguish between 4-way handshake for 802.1X and PSK, but
nl80211 API has different capabilities for each one.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The current cfg80211 limit for the maximum NL80211_ATTR_PMK length is
48, so anything larger than that will result in the operation completely
failing. Since the PMKSA entries can be used without the PMK for most
purposes (the main use case for PMK currently is offloaded FILS
authentication), try to go ahead by configuring only the PMKID for the
case where 64-octet PMK is needed (which is currently limited to only
DPP with NIST P-521 and brainpoolP512r1 curves). This can fix DPP
connections with drivers that expect to get the PMKID through this
interface while still leaving the actual 4-way handshake for user space.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This makes it easier to notice if the driver operation to manage PMKSA
cache information fails unexpectedly.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This netlink socket handle owns the connect request and is further used
by the host driver/kernel to request for the external authentication.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This command/event interface can be used by host drivers that do not
define separate commands for authentication and association but rely on
wpa_supplicant for the authentication (SAE) processing.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new disable_fils parameter can be used to disable FILS functionality
in the driver. This is currently removing the FILS Capability bit in
Extended Capabilities and providing a callback to the driver wrappers.
driver_nl80211.c implements this using a QCA vendor specific command for
now.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This nl80211 attribute uses NLA_U8 policy in cfg80211 and wpa_supplicant
needs to use same size when writing the attribute.
This fixes mesh mode regression triggered by kernel commit "net:
netlink: Update attr validation to require exact length for some types"
in v4.15-rc1 that resulted in the following debug log entry when trying
to join a mesh:
nl80211: mesh join failed: ret=-22 (Invalid argument)
Fixes: 6c1664f605 ("nl80211: Add new commands to support mesh interfaces")
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This nl80211 attribute uses NLA_U8 policy in cfg80211 and
hostapd/wpa_supplicant needs to use same size when writing the
attribute.
This fixes AP mode regression triggered by kernel commit "net: netlink:
Update attr validation to require exact length for some types" in
v4.15-rc1 that resulted in the following debug log entry when trying to
enable beaconing:
nl80211: Beacon set failed: -34 (Numerical result out of range)
Fixes: da1080d721 ("nl80211: Advertise and configure SMPS modes")
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
One of the event message for TX status was missing 'x' from the "0x"
prefix. Add that to make the used format consistent for all cookie debug
print cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Avoid same interface processing nl80211 events when at least one of
IFIDX, WDEV, or WIPHY index attribute is available in the nl80211 event
message.
Previously, a same interface processes events when ifidx and wdev id
attribute were not available in the nl80211 message. This is extended to
check the presence of wiphy index attribute as well since some radar
notifications include only WIPHY index attrbute in the nl80211 message.
Signed-off-by: Sriram R <srirrama@qti.qualcomm.com>
This adds support for SAE in AP mode with the atheros driver interface.
EVENT_RX_MGMT includes SAE processing while EVENT_AUTH would require
more changes to make this work.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
After an initial connection certain connection parameters may be
updated. It may be necessary to send these parameters to drivers since
these will be used in driver-initiated roaming cases. This commit
defines the driver_ops call for this and implements the needed
functionality for the nl80211 driver interface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows a more accurate scan result age to be fetched than the one
available through NL80211_BSS_SEEN_MS_AGO.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was originally added to allow the IEEE 802.11 protocol to be
tested, but there are no known fully functional implementations based on
this nor any known deployments of PeerKey functionality. Furthermore,
PeerKey design in the IEEE Std 802.11-2016 standard has already been
marked as obsolete for DLS and it is being considered for complete
removal in REVmd.
This implementation did not really work, so it could not have been used
in practice. For example, key configuration was using incorrect
algorithm values (WPA_CIPHER_* instead of WPA_ALG_*) which resulted in
mapping to an invalid WPA_ALG_* value for the actual driver operation.
As such, the derived key could not have been successfully set for the
link.
Since there are bugs in this implementation and there does not seem to
be any future for the PeerKey design with DLS (TDLS being the future for
DLS), the best approach is to simply delete all this code to simplify
the EAPOL-Key handling design and to get rid of any potential issues if
these code paths were accidentially reachable.
Signed-off-by: Jouni Malinen <j@w1.fi>
These allow external programs to fetch the TX and RX rate information
and signal strength for a specific STA through the hostapd control
interface command "STA <addr>". The values of these attributes are
filled in the response of nl80211 command NL80211_CMD_GET_STATION.
Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
The new wpa_supplicant network parameter group_mgmt can be used to
specify which group management ciphers (AES-128-CMAC, BIP-GMAC-128,
BIP-GMAC-256, BIP-CMAC-256) are allowed for the network. If not
specified, the current behavior is maintained (i.e., follow what the AP
advertises). The parameter can list multiple space separate ciphers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Removing interface from bridge in_br
linux_br_del_if(drv->global->ioctl_sock, in_br, ifname)
but in case of failure, the error print is incorrect:
it should show error for "in_br" instead of the wrong bridge name
"brname".
Signed-off-by: Rohit Pratap Singh <rohit.s@samsung.com>
Signed-off-by: Amit Khatri <amit.khatri@samsung.com>
It looks like these parameters related to FT have never been used, so
remove them from causing confusion. The separate update_ft_ies()
callback is used to provide the FT elements.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
NL80211_ATTR_AUTH_TYPE needs to be skipped if multiple auth_alg options
are included. The previous list missed the new FILS auth_alg here and
ended up not doing so if OPEN and FILS were included.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Check if device supports OCE STA/STA-CFON/AP specific mandatory
features. This commit includes checking based on the QCA vendor
attributes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add changes to control interface command get_capability to advertize
FILS capability, FILS AKMs suites, and FILS Authentication algorithms
based on the driver capabilities.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Set temporary disallowed BSSID list to the driver so that the driver
doesn't try to connect to any of the blacklisted BSSIDs during
driver-based roaming operation. This commit includes support only for
the nl80211 driver interface using a QCA vendor command for this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
New AKM suites like FILS-SHA256 do not use KCK and hence KCK length can
be zero. Add changes to include KCK attribute in rekey data only if the
length is non-zero.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new AKM is used with DPP when using the signed Connector to derive
a PMK. Since the KCK, KEK, and MIC lengths are variable within a single
AKM, this needs number of additional changes to get the PMK length
delivered to places that need to figure out the lengths of the PTK
components.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant tries to reinitialize an interface when a previously
removed netdev is restored (e.g., re-insert a USB dongle). If that
initialization fails (e.g., driver ejects ifconfig UP), the previous
implementation resulted in leaving the interface in incomplete state
while still claiming to upper layers that the interface status has
changed back to functional one.
Fix this by skipping the interface status update if reinitialization
fails. In other words, remain in INTERFACE_DISABLED state if the
interface cannot be re-enabled successfully.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 3e0272ca00 ('nl80211: Re-read MAC
address on RTM_NEWLINK') added the detection of external changes to MAC
address when the interface is brought up.
If the interface state is changed quickly enough, wpa_supplicant may
receive the netlink message for the !IFF_UP event when the interface
has already been brought up and would ignore the next netlink IFF_UP
message, missing the MAC change.
Fix this by also reloading the MAC address when a !IFF_UP event is
received with the interface up, because this implies that the
interface went down and up again, possibly changing the address.
Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
Current DFS domain information of the driver can be used in ap/dfs
to comply with DFS domain specific requirements like uniform spreading
for ETSI domain.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
In some practical cases, it is useful to suppress joining to node in the
distance. The new field mesh_rssi_threshold could be used as RSSI
threshold for joining.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Add support to set ignore assoc disallow to the driver so that the
driver ignores assoc disallowed bit set by APs while connecting. This is
used by drivers that handle BSS selection and roaming internally.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These functions can potentially be called with ie == NULL and ie_len ==
0. Check explitcitly for the ie == NULL case to avoid confusing
memcpy(dst, NULL, 0) calls.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is needed to allow the driver SME to perform the needed AES-SIV
operations during FILS association.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to add more parameters without having to change the
callback function prototype.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This will be used to determine what type of operations to use for STA
authentication and association.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed for configuring PMKSA cache entries to the driver with
the FILS Cache Identifier and SSID.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add support for FILS shared key offload for drivers which advertize
FILS shared key support using NL80211_CMD_CONNECT.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In case wpa_supplicant is using driver_macsec_linux, but macsec module
is not (yet) loaded in the kernel, nl_socket_alloc() fails and drv->sk
is NULL. In this case, don't call libnl functions rntl_link_add() or
rtnl_link_change() using such NULL pointer, to prevent program from
getting segmentation faults like:
Program received signal SIGSEGV, Segmentation fault.
nl_socket_get_local_port (sk=sk@entry=0x0) at socket.c:365
365 if (sk->s_local.nl_pid == 0) {
(gdb) p sk
$1 = (const struct nl_sock *) 0x0
(gdb) bt
#0 nl_socket_get_local_port (sk=sk@entry=0x0) at socket.c:365
#1 0x00007ffff79c56a0 in nl_complete_msg (sk=sk@entry=0x0,
msg=msg@entry=0x55555595a1f0) at nl.c:491
#2 0x00007ffff79c56d1 in nl_send_auto (sk=sk@entry=0x0,
msg=msg@entry=0x55555595a1f0) at nl.c:522
#3 0x00007ffff79c652f in nl_send_sync (sk=sk@entry=0x0,
msg=0x55555595a1f0) at nl.c:556
#4 0x00007ffff755faf5 in rtnl_link_add (sk=0x0,
link=link@entry=0x55555595b0f0, flags=flags@entry=1024) at route/link.c:1548
#5 0x000055555567a298 in macsec_drv_create_transmit_sc (priv=0x55555593b130,
sc=0x55555593b320, conf_offset=<optimized out>) at ../src/drivers/driver_macsec_linux.c:998
Signed-off-by: Davide Caratti <davide.caratti@gmail.com>
Process the new nl80211 event NL80211_RADAR_PRE_CAC_EXPIRED to allow the
driver to notify expiry of the CAC result on a channel.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
The userspace may want to delay the the first scheduled scan.
This enhances sched_scan to add initial delay (in seconds) before
starting first scan cycle. The driver may optionally choose to
ignore this parameter and start immediately (or at any other time).
This uses NL80211_ATTR_SCHED_SCAN_DELAY to add this via user
global configurable option: sched_scan_start_delay.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This leads to cleaner code overall, and also reduces the size
of the hostapd and wpa_supplicant binaries (in hwsim test build
on x86_64) by about 2.5 and 3.5KiB respectively.
The mechanical conversions all over the code were done with
the following spatch:
@@
expression SIZE, SRC;
expression a;
@@
-a = os_malloc(SIZE);
+a = os_memdup(SRC, SIZE);
<...
if (!a) {...}
...>
-os_memcpy(a, SRC, SIZE);
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add driver interface command using the QCA vendor extensions to check
the driverr whether to accept or reject a BSS transition candidate. For
the reject case, report an MBO reject reason code.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds reason for timeout in event CTRL-EVENT-ASSOC-REJECT whenever
connection failure happens because of timeout. This extends the
"timeout" parameter in the event to include the reason, if available:
timeout=scan, timeout=auth, timeout=assoc.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add IEEE 802.11ax definitions for config, IEEE structures, and
constants. These are still subject to change in the IEEE process.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add driver interface support to set sched_scan relative RSSI parameters
and to indicate driver support for this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds support for specifying a random TA for management frame
transmission commands and driver capability flags for indicating whether
this is supported in not-connected and connected states.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Following commit a70cd0db87 ('Don't
register for Beacon frames for IEEE 802.11ad AP'),
nl80211_get_wiphy_data_ap() is unconditionally called when starting AP.
This function tries to register for Beacon frames RX which fails for
some driver which don't support such registration and do not need it in
case the driver implements AP mode SME functionality.
Fix this by conditionally calling nl80211_get_wiphy_data_ap() like prior
to commit a70cd0db87.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
If vendor_scan_cookie is set to 0 after the scan_abort due to the scan
timeout ends in a cookie mismatch when processing the following
QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE indication. This ends up considering
the scan results as being for an external scan and thus the current
ongoing scan is not removed from the radio_work. Hence, do not reset
this vendor_scan_cookie after the scan abort so that the scan completion
event gets processed properly and vendor_scan_cookie gets cleared at
that point.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Beacon frames are not supported in IEEE 802.11ad network (DMG-beacons
used instead). To allow hostapd to manage IEEE 802.11ad AP with
device_ap_sme disabled, skip nl80211_register_beacons() for IEEE
802.11ad AP.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
This allows kernel to force disconnection if something kills the
wpa_supplicant process in a manner that does not allow proper cleanup to
be performed. The association is not supposed to be allowed to continue
after process has ended since there are number of operations that
wpa_supplicant may need to do during the association.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds processing of beacon loss events and generation of an internal
EVENT_BEACON_LOSS event based on them for wpa_supplicant processing. In
addition, number of consecutively lost (not acknowledged) packets is now
reported and TXE events are noted in the debug log.
Signed-off-by: Jouni Malinen <j@w1.fi>
Authentication and Deauthentication frames are not used in DMG/IEEE
802.11ad networks. For DMG/IEEE 802.11ad the following was implemented:
Upon receiving association request, allocate the sta object and
initialize it as if authentication took place. Upon receiving
disassociation, deallocate the sta object.
ap_sta_disassociate/ap_sta_deauthenticate/ap_sta_disconnect all use
disassociation instead of deauthentication. In driver_nl80211,
i802_sta_deauth() is routed to i802_sta_disassoc().
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
It was possible that nl80211_get_hw_feature_data() function would return
NULL when num_modes is not set to zero. This might result in a later crash
when accessing hw.modes. This may be reproduced with hwsim oom tests, for
example, dbus_connect_oom.
Fix that by zeroing num_modes if NULL is returned.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This fixes the netlink attribute identifier for the scan flags when
using QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add support for:
1. Setting scan dwell time
2. Parsing scan start TSF and beacon received TSF reported
by the driver
3. Setting driver capabilities for the above
These capabilities are needed for Beacon Report radio measurement.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add the following parameters to scan request:
1. Dwell time on each channel.
2. Whether the specified dwell time is mandatory.
In addition, add to scan results info the time that the scan actually
started, and to each scan result the time the beacon/probe was received,
both in terms of TSF of the BSS that the interface that requested the
scan is connected to (if available).
Add flags to indicate whether the driver supports dwell time
configuration and scan information reporting.
This scan configuration and information is required to support beacon
report radio measurement.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This allows the vendor scan to be optimized when a response is needed
only from a single, known BSS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
On a connect nl80211 event, wpa_supplicant uses
wpa_driver_nl80211_get_ssid() to fetch the current associated SSID to
compare to existing configurations. However,
wpa_driver_nl80211_get_ssid() uses drv->ssid, which is a cached value.
It is set when we explicitly initial a connect request using
wpa_supplicant. If the association was initiated outside of
wpa_supplicant, we need another way to populate drv->ssid. This commit
sets drv->ssid based on cfg80211 BSS information on connect/associate
nl80211 events.
Signed-off-by: Ningyuan Wang <nywang@google.com>
Commit adcd7c4b0b ('nl80211: Support
vendor scan together with normal scan') made the drv->scan_state updates
for NL80211_CMD_NEW_SCAN_RESULTS and NL80211_CMD_SCAN_ABORTED
conditional on drv->last_scan_cmd being NL80211_CMD_TRIGGER_SCAN. This
missed the part about the possibility of last_scan_cmd == 0 and an
externally started cfg80211 scan is ending. This could leave
drv->scan_state into SCAN_STARTED state even after the scan was
completed. Consequently, hwsim test cases could get stuck in reset()
handler waiting for scan to terminate.
Fix this by updating drv->scan_state also in drv->last_scan_cmd == 0
case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds support for nl80211 NL80211_CMD_SET_MULTICAST_TO_UNICAST
command.
By setting the new hostapd configuration option multicast_to_unicast=1,
hostapd configures this AP to perform multicast to unicast conversion.
When enabled, all multicast packets with ethertype ARP, IPv4, or IPv6
(possibly within an 802.1Q header) will be sent out to each station once
with the destination (multicast) MAC address replaced by the station's
MAC address. Note that this may break certain expectations of the
receiver, e.g., the ability to drop unicast IP packets encapsulated in
multicast L2 frames, or the ability to not send destination unreachable
messages in such cases.
This also does not implement Directed Multicast Service (DMS).
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Do not use the generic bss_info_handler() design to fetch all scan
results into temporary memory buffer. Instead, use a separate BSS info
handler that fetches the requested information without fully parsing the
BSS entries and without allocating any memory for collecting all the
results.
This is also simplifying bss_info_handler() and nl80211_parse_bss_info()
design by getting rid of the special case that was used only for
nl80211_get_assoc_freq() and not normal scan result fetching.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of fetching all scan results to a temporary buffer, debug print
scan result dump directly from the message handler function one BSS at a
time.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows a single scan result to be parsed at a time. This is a step
towards optimizing scan result fetching without having to allocate
memory for all entries at the same time.
Signed-off-by: Jouni Malinen <j@w1.fi>
The way the removal of duplicated (one per frequency) BSS entries in the
cfg80211 scan results were removed in driver_nl80211_scan.c
bss_info_handler() depended on having the full scan results available to
allow iteration through the other entries. This is problematic for the
goal of being able to optimize memory allocations for scan result
fetching in a manner that would not build the full result buffer in
memory.
Move this duplicate removal into bss.c since it has sufficient
information available for doing the same determination of which one of
two BSS entries is more current.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_priv did not yet support Beacon frame IEs (res->beacon_ie_len) which
resulted in invalid scan data being accepted in driver_privsep.c. Add
support for res->beacon_ie_len and also fix the validation step to take
this new variable length field into account.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows a single scan result to be checked at a time. This is a step
towards optimizing scan result fetching without having to allocate
memory for all entries at the same time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This untangles the NL80211_CMD_GET_SURVEY handler loop from
NL80211_CMD_GET_SCAN processing so that the per-channel noise
information can be fetched with a common function to a local data
structure that can then be easily used to update individual scan results
(a single BSS) instead of having to go through a full set of scan
results. This is a step towards optimizing scan result fetching without
having to allocate memory for all entries at the same time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These are used only within driver_wired_common.c now at the end of the
refactoring changes, so there is no need to make these helper functions
available outside driver_wired_common.c.
Signed-off-by: Jouni Malinen <j@w1.fi>
This uses libnl3 to communicate with the macsec module available on
Linux. A recent enough version of libnl is needed for the macsec.h file
(which is not yet available in a formal libnl release at the time of
this commit).
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
