Add a vendor attribute for EHT testbed STA to configure the
SCS traffic description support in the EHT capabilities of an
Association Request frame.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is an event indicating to the user space firmware page fault
summary report that the driver has generated from firmware indications.
This summary report is used to analyze major cause of page faults and
associated debug information.
Signed-off-by: Mukul Sharma <quic_mukul@quicinc.com>
Add a new QCA subcommand QCA_NL80211_VENDOR_SUBCMD_REGULATORY_TPC_INFO
and related attributes qca_wlan_vendor_attr_tpc_links,
qca_wlan_vendor_attr_tpc definition to query transmit power information
on STA interface from the driver for a connected AP.
The information includes regulatory max transmit power limit, AP local
power constraint advertised from AP's Beacon and Probe Response frames.
For PSD power mode, the information includes PSD power levels for each
subchannel of operating bandwidth. The information is driver calculated
power limits based on current regulatory domain, AP local power
constraint and other IEs. The information will be set to target. Target
will decide final TX power based on this and chip specific power
conformance test limits (CTL), and SAR limits.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
For AP MLD case, HT-scan and ACS happens per link. To determine the
correct link, link id is required.
Signed-off-by: Chenming Huang <quic_chenhuan@quicinc.com>
Define a new command QCA_TSF_SYNC_GET_CSA_TIMESTAMP in qca_tsf_cmd to
retrieve the TSF time value at which the AP will move and starts
beaconing on a new channel. Userspace queries this TSF after receiving
NL80211_CMD_CH_SWITCH_STARTED_NOTIFY event on the AP interface. This TSF
can be communicated via an OOB mechanism to connected STAs which may
fail to receive the CSA frames due to channel congestion.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
Currently the documentation for QCA_WLAN_VENDOR_ATTR_CONFIG_MLO_LINK_ID
indicates it is only for use inside nest attribute
QCA_WLAN_VENDOR_ATTR_CONFIG_MLO_LINKS. Update the documentation to
allow it to be used outside that nest as well.
Signed-off-by: Mohan Prabu <quic_mprabub@quicinc.com>
Enumeration qca_wlan_roam_stats_frame_subtype defines the various frame
subtypes which may be collected by the driver and reported via the
QCA_WLAN_VENDOR_ATTR_ROAM_STATS_FRAME_SUBTYPE attribute.
Two of the enumerators are:
* QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_PREAUTH
* QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_REASSOC
These were initially defined and used to respectively report
Authentication Response and Reassociation Response frames.
Now there is a requirement to also report Authentication Request and
Reassociation Request frames. In order to satisfy this requirement,
add two new enumerators:
* QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_AUTH_REQ
* QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_REASSOC_REQ
Note that the first of these uses the standard term "AUTH" instead of
the confusing term "PREAUTH" used previously.
And to align with that naming, and in order to clearly show the usage
of the original enumerators, rename them to:
* QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_AUTH_RESP
* QCA_WLAN_ROAM_STATS_FRAME_SUBTYPE_REASSOC_RESP
Furthermore, Authentication Request/Response frame refers to the
Authentication frames sent by the non-AP STA and AP, respectively.
And finally, to support backward compatibility with applications using
the original enumerators, redefine those in terms of the new names.
Signed-off-by: Chunquan Luo <quic_chunquan@quicinc.com>
Fetch AP BSSID from each roam connection frame and cache the info in the
WLAN driver. When user space gets roam stats by
QCA_WLAN_VENDOR_ATTR_ROAM_STATS_INFO, user space can now collect the AP
BSSID info for roam issue.
Signed-off-by: Chunquan Luo <quic_chunquan@quicinc.com>
Define a new QCA vendor attribute to configure traffic
shaping policy applied during coex scenarios.
Signed-off-by: Shailendra Singh <quic_shasing@quicinc.com>
Add an attribute QCA_WLAN_VENDOR_ATTR_ADD_STA_NODE_IS_ML to the
ADD_STA_NODE command. If this attribute is set, it implies that the node
being added is an MLD node.
Signed-off-by: Adil Saeed Musthafa <quic_adilm@quicinc.com>
Extend QCA_WLAN_VENDOR_ATTR_CONFIG_CHAN_WIDTH_UPDATE_TYPE attribute to
support handling interoperability issues with APs which don't handle
the maximum bandwidth change indication correctly.
Additionally define an enum for possible values of
QCA_WLAN_VENDOR_ATTR_CONFIG_CHAN_WIDTH_UPDATE_TYPE.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add QCA vendor attributes to indicate various MLO capabilities supported
by the WLAN driver to userspace. These capabilities are usually reported
by the firmware during the initial bootup handshake with the driver.
Signed-off-by: Mukul Sharma <quic_mukul@quicinc.com>
Add a vendor attribute for an EHT DUT to configure the type of TID-To-Link
Mapping Negotiation Support for testing purposes.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a QCA vendor attribute QCA_WLAN_VENDOR_ATTR_CONFIG_PEER_AMPDU_CNT to
enable configuration of TX maximum aggregate size with a specific peer.
This can be used to improve performance in noisy environment. In AP
mode, the peer MAC address of the associated STA is specified with
QCA_WLAN_VENDOR_ATTR_CONFIG_PEER_MAC.
Signed-off-by: Will Huang <quic_wilhuang@quicinc.com>
Rename the attribute QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_PEER_MAC
to a generic name QCA_WLAN_VENDOR_ATTR_CONFIG_PEER_MAC, so other
configuration commands can reuse it. And make backward compatibility of
QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_PEER_MAC, define it as same
value of QCA_WLAN_VENDOR_ATTR_CONFIG_PEER_MAC (35).
Signed-off-by: Will Huang <quic_wilhuang@quicinc.com>
Add a vendor attribute for EHT testbed STA to configure MLD ID in the ML
Probe Request frame transmitted as part of host initiated scan request.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a new QCA vendor sub command QCA_NL80211_VENDOR_SUBCMD_TX_LATENCY to
configure, retrieve, and report per-link transmit latency statistics.
When used as a command, userspace configures transmit latency monitoring
and get the corresponding statistics of the last period. When used as a
command response, driver replies the get action from userspace with the
statistics of the last period. When used as an event, driver reports the
statistics periodically.
Signed-off-by: Yu Wang <quic_yyuwang@quicinc.com>
Define an attribute for high RSSI roam trigger threshold. STA is
expected to trigger roam if the current connected AP's RSSI gets above
this high RSSI threshold. STA's roam attempt on high RSSI threshold aims
to find candidates from other better Wi-Fi bands.
Signed-off-by: Sunil Dutt <quic_usdutt@quicinc.com>
Add three vendor roam control attributes to configure the roaming
parameters dynamically.
QCA_ATTR_ROAM_CONTROL_CONNECTED_LOW_RSSI_THRESHOLD controls the
connected AP's low RSSI threshold to trigger the neighbor lookup.
QCA_ATTR_ROAM_CONTROL_CANDIDATE_ROAM_RSSI_DIFF and
QCA_ATTR_ROAM_CONTROL_6GHZ_CANDIDATE_ROAM_RSSI_DIFF control the RSSI
difference threshold between the connected AP and the new candidate AP
for the roam to trigger.
Co-authored-by: Sunil Dutt <quic_usdutt@quicinc.com>
Signed-off-by: Sunil Dutt <quic_usdutt@quicinc.com>
Extend enum qca_wlan_vendor_attr_mlo_peer_prim_netdev_event to add MLD
MAC address, the number of links, and link info. Link info contains
ifindex and MAC address of each link of a non-AP MLD that was negotiated
in ML association.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add vendor attribute IDs QCA_WLAN_VENDOR_ATTR_ROAM_STATS_ORIGINAL_BSSID,
QCA_WLAN_VENDOR_ATTR_ROAM_STATS_CANDIDATE_BSSID, and
QCA_WLAN_VENDOR_ATTR_ROAM_STATS_ROAMED_BSSID for updating roaming AP
BSSID to user space to enable user space collecting the BSSID for
roaming issues.
Signed-off-by: Chunquan Luo <quic_chunquan@quicinc.com>
QCA vendor extension is used for NDP setup. This defines the new
attributes QCA_WLAN_VENDOR_ATTR_NDP_CSIA_CAPABILITIES and
QCA_WLAN_VENDOR_ATTR_NDP_GTK_REQUIRED to support GTKSA, IGTKSA, and
BIGTKSA for NDP setup.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Extend QCA_WLAN_VENDOR_ATTR_CONFIG_OPTIMIZED_POWER_MANAGEMENT
attribute to support enum qca_wlan_vendor_opm_mode.
Add QCA vendor attribute QCA_WLAN_VENDOR_ATTR_CONFIG_OPM_ITO and
QCA_WLAN_VENDOR_ATTR_CONFIG_OPM_SPEC_WAKE to configure inactivity
timeout and speculative wake interval in User defined optimized
power save mode.
Signed-off-by: Vishal Miskin <quic_vmiskin@quicinc.com>
Update documentation of the QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_WIDTH
and QCA_WLAN_VENDOR_ATTR_CONFIG_CHAN_WIDTH_UPDATE_TYPE attributes to
indicate support for per-MLO link configuration.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add support for per-MLO link configurations in
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and
QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION commands.
Additionally, add documentation for
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and
QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION commands.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Define a new QCA vendor test config attribute to configure powersave
on MLO links.
This attribute is used for testing purposes.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Extend bitwise mask in enum qca_wlan_tdls_caps_features_supported to get
the TDLS wider bandwidth capability from the driver.
Signed-off-by: Aleti Nageshwar Reddy <quic_anageshw@quicinc.com>
Use zero value with QCA_WLAN_VENDOR_ATTR_CONFIG_EHT_MLO_MAX_NUM_LINKS to
restore the device default maximum number of allowed MLO links
capability.
Also, as per IEEE 802.11be/D3.0, the maximum number of allowed links for
an MLO connection is 15. Update the documentation of the attribute to
indicate the same.
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
Define a QCA vendor command to configure MLO link id to the driver on
which the TDLS discovery response frame needs to be transmitted when the
local station is connected in MLO mode. This command is configured to
the driver the prior to every TDLS discover frame transmission when the
station is connected in MLO mode. If the station is connected in non-MLO
mode this command is not configured to the driver for TDLS discovery
frame transmission.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a new vendor command and attributes to notify TID-to-link mapping
changes to the userspace.
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
Define a new QCA vendor attribute to configure channel bandwidth to the
driver for CTS frame transmission. This is used for testing purposes.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add QCA_WLAN_VENDOR_FEATURE_ENHANCED_AUDIO_EXPERIENCE_OVER_WLAN in
enum qca_wlan_vendor_features to indicate the device supports enhanced
audio experience over WLAN feature.
Also, update the documentation where other subcommand(s) or attribute(s)
require this new feature flag. These subcommand(s) and attributes are
under development and would be restricted to the supported drivers
advertising QCA_WLAN_VENDOR_FEATURE_ENHANCED_AUDIO_EXPERIENCE_OVER_WLAN.
As such, it is still acceptable to introduce a new requirement for the
previously defined interface.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
Add vendor attributes for EHT testbed STA configuration.
This includes enabling STR MLMR mode and forcing power save
on active MLO links for a defined number of beacon periods.
Signed-off-by: Gururaj Pandurangi <quic_panduran@quicinc.com>
Add vendor attributes related to MLO and EMLSR mode
capability configuration for EHT testbed STA. It includes
EHT OM control support and EMLSR padding delay configuration.
Also, generalise the naming of HE OMI control enumeration to
OMI control as it now consists of both HE and EHT OMI control
fields.
Signed-off-by: Gururaj Pandurangi <quic_panduran@quicinc.com>
Add vendor attributes related to MLO and EMLSR mode
capability configuration for EHT DUT. This includes forcing
active MLO links and invoking EMLSR mode entry or exit.
Signed-off-by: Gururaj Pandurangi <quic_panduran@quicinc.com>
IEEE 802.11be enables multiple links between STA and AP. Each of the
link has its own set of statistics. Add additional attributes required
to fetch link layer statistics per MLO link.
For MLO connection, per MLO link statistics will be sent with the new
attribute QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK. Also, cumulative
statistics of all the MLO links will be sent outside
QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK to be compatible with legacy user
space.
For non-MLO connection, the statistics will be sent without being nested
inside QCA_WLAN_VENDOR_ATTR_LL_STATS_MLO_LINK attribute.
Co-authored-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
