Allow clients to specify the BSSID of an auto GO. If the auto GO has been
discovered on another interface, optimize scan frequency by performing
a single channel scan first. Android and ChromeOS use this to streamline
auto GO discovery.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
This enables connection managers to receive and use this information in
the same manner that other station information is exposed.
Signed-off-by: David Ruth <druth@chromium.org>
As a workup action during disassociation, wpa_supplicant checks if the
disconnection could have been caused by PSK mismatch during WPA 4-way
handshake with function could_be_psk_mismatch() in event.c. A MSG_INFO
message will be sent on the control interface when there could be a PSK
mismatch, and this heuristic can be useful to indicate if the
disconnection is caused by a wrong passphrase provided by the user.
Here, propagate a new D-Bus signal 'PskMismatch' to notify other
applicantions.
Signed-off-by: Yichen Yu <yichenyu@chromium.org>
- Do not try to enable 80 MHz if 40 MHz is disabled or not selected (e.g.,
due to obss_scan).
- If it is not possible to use 80 HMz or even 40 MHz, still attempt to
configure HE40/VHT40/HE20/VHT20 instead of bailing out.
- When bailing out, also disable HE.
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
If the PHY supports both 5 GHz and 6 GHz bands, there will be two
different struct hostapd_hw_modes with mode HOSTAPD_MODE_IEEE80211A,
one for each band, with potentially different capabilities.
Check that the struct hostapd_hw_modes actually contains the frequency
before selecting it.
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
ibss_mesh_setup_freq() has become a 342 line function with 23 local
variables, 1 or 2 goto labels depending on ifdefs and its logic is
quite unpredictable.
Split it into multiple functions. No functional change intended, it
should be bug-compatible with the original code, except for some log
messages that are skipped more often.
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Add a new network profile option enable_4addr_mode=1 that puts an
interface in 4addr mode, for interfaces meant to be added to a bridge.
Signed-off-by: Konstantinos Natsakis <infradead.org@aleph-0.net>
wpa_supplicant_need_to_roam_within_ess() applies bias to the minimum
difference of the signal level required to roam if the roam is from 2.4
GHz to higher band, but doesn't apply bias if the roam is from a lower
band to 6 GHz. Add bias towards 6 GHz, as 6 GHz networks usually provide
higher throughput.
Signed-off-by: Kaidong Wang <kaidong@chromium.org>
Move the logic of picking the best driver pref freq into a separate
function, and use this to extend the functionality for invitation
process.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Enable MLO for SAE authentication when the driver indicates the AP MLD
address in an external authentication request. The MAC address of the
interface on which the external authentication request received will be
used as the own MLD address.
This commit does below for enabling MLO during external SAE
authentication:
- Use MLD addresses for SAE authentication.
- Add Basic Multi-Link element with the own MLD address in SAE
Authentication frames.
- Send SAE Authentication frames with the source address as the own MLD
address, destination address and BSSID as the AP MLD address to the
driver.
- Validate the MLD address indicated by the AP in SAE Authentication
frames against the AP MLD address indicated in external authentication
request.
- Store the PMKSA with the AP MLD address after completing SAE
authentication.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
The initial MACsec implementation required the EAP Session-Id to be at
least 65 octets long and by truncating the value to that length, the
practical limit of functional cases was limited to that exact length of
65 octets. While that happens to work with EAP method that use TLS, it
does not work with most other EAP methods.
Remove the EAP Session-Id length constraint and allow any length of the
Session-Id as long as the EAP method provides one. In addition, simplify
this be removing the unnecessary copying of the Session Id into a new
allocated buffer.
Fixes: dd10abccc8 ("MACsec: wpa_supplicant integration")
Fixes: a93b369c17 ("macsec: Support IEEE 802.1X(EAP)/PSK MACsec Key Agreement in hostapd")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
python2 is deprecated so move script to python3.
While at it, make some minor adjustments.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
While checking for stale BSSes, the current time is used as a basis and
then based on age the stale check time is calculated, but if this is
done too early in the boot and if either BOOTTIME/MONOTONIC (the one
Zephyr uses by default) are used then the stale check time underflows
and goes to future causing active BSS entries in the scan to be treated
as stale and flushed.
Fix this by adding a check before calculating stale time and ignore this
check till the system reaches the BSS expiration time (this would never
happen with REALTIME clock).
Signed-off-by: Krishna T <krishna.t@nordicsemi.no>
Signed-off-by: Sridhar Nuvusetty <sridhar.nuvusetty@nordicsemi.no>
The RO variable is being assigned before the SSID is NULL checked, so,
any invalid configuration leads to a segmentation fault.
Fixes: d8d2b3a338 ("Implement read-only mode for SSIDs from the additional config (-I)")
Signed-off-by: Chaitanya Tata <chaitanya.tk17@gmail.com>
The previous implementation handles PMKSA cache attempts with AP MLD
address only for SME-in-wpa_supplicant cases since wpa_s->valid_links
wouldn't be set for SME-in-driver cases.
Fix SME-in-driver behavior by enabling PMKSA cache attempts with AP MLD
address when driver supports MLO and SME offload to driver.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Store PMKSA with AP MLD address while processing connect event for OWE
and FILS when the connection is MLO capable.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
It was possible to hit a case where the SAE PT had not yet been derived,
e.g., when using P2P group re-invocation. Update PT use at the time
authentication is started, if needed, to avoid this. While this is not
really ideal from the externally observable timing view point, this is
done only for the case where there is no other option available with a
dynamically changing network configuration for P2P. Similar design was
already in place for the SAE offload-from-driver (external auth) case.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Both P2P GO and client always save key_mgmt = WPA_KEY_MGMT_PSK in the
configuration when storing a persistent group. Next time, when a GO is
started as an autonomous GO on a 6 GHz channel, it will change key_mgmt
to SAE and use hash-to-element mechanism, but the P2P client doesn't
change the parameter even if the group it wants to join is operating on
a 6 GHz channel. The P2P connection will be failed due to reason 'reject
due to mismatch with WPA/WPA2'.
Enable SAE-H2E for P2P client in this case.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Commit 3a0edb2cd8 ("SAE: Enable H2E for 6 GHz BSS") started enabling
H2E automatically for SAE use on the 6 GHz band, but it did not update
these steps in verifying whether the STA has matching configuration for
a BSS that mandates use of H2E and whether to use PT for SAE in SME.
Update these to be aware of automatic H2E enabling.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
ssid->ocv is defined within CONFIG_OCV block, so the use for it needs to
match.
Fixes: dc7e330e0b ("Set OCV capability based on Association Request frame RSNE")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Currently, OCV self-capability is being set into the RSN supplicant
state machine only during the initial connection and never getting
updated. But for the driver-SME cases the driver may enable/disable OCV
in (Re)Association Request frame RSNE based on the AP chosen to roam.
This will lead to missing synchronization between wpa_supplicant and the
driver. Thus, update OCV self-capability in the wpa_supplicant RSN state
machine based on the (Re)Association Request frame RSNE indicated in the
connect response.
Signed-off-by: Aleti Nageshwar Reddy <quic_anageshw@quicinc.com>
The check for PBC overlap on a partner link should not be done unless
the current interface is actually in active PBC mode. Furthermore, the
wpa_s->wps_overlap variable needs to be cleared in additional places to
avoid leaving it set indefinitely.
This was found with the following test case sequence:
dbus_wps_pbc_overlap dbus_p2p_two_groups
Fixes: b43e19f3f3 ("WPS: Cross band overlap detection with multiple interfaces")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Commit ace0fbdb69 ("P2P: Fix segfault when PBC overlap is detected")
removed the external calls to this function, but did not mark it static.
Mark it static now to clarify expected uses through the
wpas_p2p_pbc_overlap_cb() timer handler.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
There was a race condition between the NFC handover requester and
selector role processing that ended up not sending out the alternative
proposal in some cases. Catch those at the end of
run_dpp_handover_client() processing (or immediately after returning
from that function without having sent out the alternative proposal).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
IEEE Std 802.11ax-2021, 12.12.2 requires this, so force MFPR=1 when
associating on the 6 GHz band so that ieee80211w=1 (i.e., MFPC=1 MFPR=0)
configuration can be used to get MFPC=1 behavior on other bands and
MFPR=1 on the 6 GHz band.
Signed-off-by: Jouni Malinen <j@w1.fi>
Allow specifying preferred GO band in addition to frequency. If a band
is specified, the first two scans will be limited to only non-DFS
channels to shorten scan times, and the next two will scan the entire
band.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
Now that we check in PMKSA cache code whether the entry was created for
the same local address, it is fine to leave the old entries in the cache
even if we have changed addresses. This allows a valid PMKSA cache entry
to be used when restoring the same MAC address for the same ESS.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the implementation more readable by sharing the same set of
enum values for all the parameters related to what kind of random MAC
addresses are used.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_s->last_mac_addr_change.sec might be zero in the special case of UML
testing with time travel since it would be possible to complete the test
case steps within one second of the system start.
Signed-off-by: Jouni Malinen <j@w1.fi>
When MAC address randomization settings change we should use a new MAC
address even if we are associating to the same ESS.
For example, consider this scenario:
- hardware MAC is being used,
- we disconnect from the network,
- policy/style is changed via D-Bus to turn randomization on,
- we reconnect to the same network.
In the last step a randomized MAC address should be used.
Changes to the randomization settings include both changes to the
policy/style to be used and changes to the pregenerated MAC address
value in case of mac_addr==3.
Signed-off-by: Andrzej Ostruszka <amo@semihalf.com>
If the CreateInterface command was used to create a virtual AP
interface, deleting this interface using the RemoveInterface command was
also bringing down the primary interface.
wpa_supplicant never uses hostapd style multi-BSS setup with
type=WPA_IF_AP_BSS and setup_ap=1 to if_add() when creating an AP
interface in wpa_driver_nl80211_if_add(), so it should not go through
the multi-BSS tear down procedure in wpa_driver_nl80211_if_remove(). The
virtual AP resources init and deinit are well handled in
wpa_driver_nl80211_init() and wpa_driver_nl80211_deinit().
Collapse the interface type to WPA_IF_STATION for the D-Bus interface to
skip the multi-BSS cleanup procedure. This is inline with the control
interface design. Add comments before the code to avoid confusion.
Signed-off-by: Jintao Lin <jintaolin@chromium.org>
The driver is expected to translate the link addresses to MLD addresses
when processing an Authentication frame from a MLD AP. Thus, accept
Authentication frame when the peer matches the expected MLD address.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
In case both the local driver and the AP support MLD, request an MLD
association from the driver.
When processing the association event from the driver verify that the
multi link information in the (Re)Association Response frame ML element
matches the links on which the association was expected.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
In case both the local driver and the AP support MLD, request an MLD
authentication from the driver. When processing the authentication event
from the driver verify that the MLD address in the authentication data
matches that of the requested AP.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Authentication frames include several fixed body parts (see Table 9-68
(Authentication frame body) and Table 9-69 (Presence of fields and
elements in Authentication frames) in IEEE P802.11-REVme/D2.0).
To be able to parse the IE part, these fields need to be skipped. Since
SAE logic already implements this parsing, change SAE authentication
handling functions to return the offset to the IE part. This preparation
is needed for future MLD patches that need to parse out the ML related
elements in the Authentication frames.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
In case of drivers that offload the 4-way handshake to the driver, there
was no way of updating wpa_supplicant about the transition disable
bitmap received as a part of EAPOL-Key msg 3/4.
With latest provisions in cfg80211_port_authorized(), the TD bitmap can
be sent to the upper layer. Parse that as a part of the port authorized
event and set the transition disable information accordingly.
Signed-off-by: Vinayak Yadawad <vinayak.yadawad@broadcom.com>
chromeOS uses random generated MAC address for AP interface so that the
device could remain anonymous and untrackable. Add an address parameter
for CreateInterface method to pass in OS managed MAC address.
Signed-off-by: Jintao Lin <jintaolin@chromium.org>
Fix a potential memory leak in CreateInterface method.
Fixes: 0ba266d86c ("dbus: Add virtual interface create/remove logic to be inline with ctrl_iface")
Signed-off-by: Jintao Lin <jintaolin@chromium.org>
RSNXE bits were modified, so update the relevant places accordingly.
Please note, WLAN_RSNX_CAPAB_PROT_RANGE_NEG was renamed to
WLAN_RSNX_CAPAB_URNM_MFPR and the bit position is changed to 15 instead
of 10, while BIT 10 is used for WLAN_RSNX_CAPAB_URNM_MFPR_X20 and is not
supported yet.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Check the HE membership selector and don't use the BSS
if required but not supported by HW.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add support to handle external authentication request with a different
SAE AKM suite compared to the current connection AKM suite. This is
needed to support cross AKM roaming between SAE and SAE-EXT-KEY AKM
suites.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
PASN deauthentication event is sent by the underlying driver to delete
the keys in wpa_supplicant PTKSA cache. So don't send clear secure
context command to the driver again as it is already aware of it.
Fixes: 74d894a2 ("PASN: Offload handshake for multiple peers from the driver")
Signed-off-by: Vinay Gannevaram <quic_vganneva@quicinc.com>
Though not explicitely forced by IEEE 802.11be draft yet, it makes sense
to apply the same logic for MLD as for 6 GHz BSSs. Change
wpa_supplicant_ssid_bss_match() accordingly.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
MAX_NUM_MLD_LINKS is 15, thus u8 isn't enough for the bitmap. Fix it.
While at it, clean MLO information better.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add the required ML and RNR definitions and report the information in
BSS command.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Allows informing the connection manager of additional information on CQM
events. Allows the connection manager to request the same information
on demand by using the existing "SignalPoll" method.
* Add new property "SignalChange"
* Add storage for wpa_signal_info into wpa_supplicant context
object
* Copy memory from event to context object on CQM Event
* Write a common conversion method to be used by both "SignalPoll" and
this property
Signed-off-by: David Ruth <druth@chromium.org>
Facilitate emitting more station information over D-Bus for use by the
connection manager.
* Add storage for more NL80211_STA_INFO_* fields to data structures, and
move them through the system.
* Reorder NL80211_STA_INFO_* fields in driver_nl80211.c to match the
ordering in nl80211.h.
* Convert signal field to an integer to support holding WPA_INVALID_NOISE
and avoid changing logging.
* Add fields to hostap_sta_driver_data to capture more information
* fcs_error_count
* beacon_loss_count
* expected_throughput
* rx_drop_misc
* rx_mpdus
* rx_hemcs
* tx_hemcs
* rx_he_nss
* tx_he_nss
* avg_signal
* avg_beacon_signal
* avg_ack_signal
* Add struct hostap_sta_driver_data to struct wpa_signal_info and remove
redundant fields and redundant attribute parsing
* Change logging when printing txrate to handle unsigned long
value
Signed-off-by: David Ruth <druth@chromium.org>
Since wpa_supplicant can change MAC address of the interface on its own
(with randomization enabled) it makes sense to introduce MACAddress as a
property of the interface and send notifications about its change.
This allows other applications to just use D-Bus instead of both
communicating over D-Bus with wpa_supplicant and listening to Netlink
notifications for MAC changes.
Signed-off-by: Andrzej Ostruszka <amo@semihalf.com>
Add support to consider EHT rates while calculating the estimated
throughput for scan results.
- The estimated EHT throughput uses the HE 0.8 usec GI rates from the
relevant EHT-MCS tables from IEEE P802.11be/D2.0, 36.5.
- The minimum SNR values for EHT rates (4096-QAM) are derived by adding
the existing minimum SNR values of 1024-QAM rates from HE tables and
the difference between the values of minimum sensitivity levels of
1024-QAM rates and 4096-QAM rates defined in Table 36-67 (Receiver
minimum input level sensitivity) in IEEE P802.11be/D2.0.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
There are several cases where memory allocations are not
checked for success. Add conditions and error messages, as some
analyzers complain about that.
Signed-off-by: Micha Hashkes <micha.hashkes@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Even if the use of H2E isn't strictly mandatory when using SAE on 6 GHz,
WPA3-Personal pushes it on 6 GHz, so enable H2E automatically when
connecting to a BSS on the 6 GHz band if it was not enabled in the
configuration.
Signed-off-by: Jimmy Chen <jimmycmchen@google.com>
When WPS is running simultaneously on multiple per-band radios (e.g., a
separate 2.4 GHz and 5 GHz band radios in an AP device), handle
synchronization of scan results, detect PBC session overlap, and cancel
WPS for enrollees on both interface, if the UUID of the registrars on
different bands differ.
Signed-off-by: Sai Pratyusha Magam <quic_smagam@quicinc.com>
Just like with WPA-PSK and keyids it may be desired to identify
connecting clients to provide additional network filtering.
This does:
- extend DPP_EVENT_AUTH_SUCCESS to expose public
key hash of the peer so the system can pick it
up and use for identification later
- store public key hash in PMKSA from DPP Network
Intro for later use
- extend sta mib to print out the dpp_pkhash
from PMKSA if present
- extend AP_STA_CONNECTED to include the
dpp_pkhash from PMKSA if present
Signed-off-by: Michal Kazior <michal@plume.com>
This event is generated in a couple of places. It'll be easier to extend
the event with additional metadata if it's generated in a single place.
Signed-off-by: Michal Kazior <michal@plume.com>
On NixOS[1] - a Linux distribution which allows to configure a full OS
declaratively - it's possible to configure SSIDs for `wpa_supplicant`
like this:
networking.wireless.networks = {
myssid = {
pskRaw = "<redacted>";
};
};
It's also possible to add networks "imperatively" using `wpa_gui` or
`wpa_cli`. However it's not possible to do both because if the first
option is used, NixOS creates a read-only symlink at
`/etc/wpa_supplicant.conf` and then it's not possible for
`wpa_supplicant` anymore to write to it.
This patch aims to help us changing this: while "declarative" SSID
configuration can be quite useful, it's a bad idea for e.g. sensitive
stuff like a WPA2 enterprise network.
The original idea was to use `-I`[2] for immutable configs (including
"declarative" networks) on NixOS and `-c /etc/wpa_supplicant.conf` for
anything "imperative".
However this doesn't really work out because if a wifi network from a
config file specified with `-I` is changed by e.g. `wpa_gui`, it's
silently overwritten in `/etc/wpa_supplicant.conf` (specified with
`-c`) which is IMHO unintuitive (in our case at least). This patch
basically declares each network defined in a config file passed via `-I`
to `wpa_supplicant` as "read-only" and doesn't write these "read-only"
networks to `/etc/wpa_supplicant.conf`.
A bit more context can be found on GitHub in the PR where I implemented
this[3].
[1] https://nixos.org/
[2] Added in e6304cad47
[3] https://github.com/NixOS/nixpkgs/pull/113716
Signed-off-by: Maximilian Bosch <maximilian@mbosch.me>
Add new 'mac_addr' policy (3) with which supplicant expects to also
obtain 'mac_value' with pregenerated value of MAC address to be used for
given SSID.
The main difference between this policy and policy 1 is the ability to
control persistence of the MAC address used. For example if there is
a requirement to always use the same (but random) MAC address for given
SSID (even if user removes/forgets the network) this could be handled
outside of the wpa_supplicant by using some SSID based hashing scheme to
generate MAC (or by just storing the randomly generated one) and
providing it to wpa_supplicant together with mac_addr=3 policy.
Signed-off-by: Andrzej Ostruszka <amo@semihalf.com>
IEEE Std 802.11ax-2021, 12.12 explicitly disallows use of Open System
authentication without encryption on the 6 GHz band.
Signed-off-by: Sharadanand Karanjkar <skaranjkar@datto.com>
As P2P GOs are not expected to be collocated, i.e., they are not
expected to be announced in the RNR element of other APs, they can
operate only on preferred scanning channels (PSCs).
When performing a full scan for P2P discovery, include only the 6 GHz
PSCs (if supported) to avoid scanning channels on which P2P GOs are not
expected to reside.
While at it also fix couple of places that missed including 60 GHz
channels in P2P full scan.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add a callback handler to notify details of a PMKSA cache entry when it
is added to the PMKSA cache. This can be used to provide external
components more convenient access to the PMKSA cache contents.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
For WPA2/WPA3 authentication mode, wpa_supplicant needs to notify
CurrentAuthMode property change when wpa_s->key_mgmt changes, so
NetworkManager can judge whether it needs to request a password based on
this.
Call wpas_notify_auth_changed() when starting a new connection item,
i.e., after having updated wpa_s->key_mgmt.
Signed-off-by: xinpeng wang <wangxinpeng@uniontech.com>
SSID may include unprintable characters. This change converts
unprintable characters into printable form before printing SSID in the
function wpas_send_ctrl_req(). The conversion is based on the function
wpa_ssid_txt().
Signed-off-by: Kaidong Wang <kaidong@chromium.org>
In case of drivers supporting 4-way handshake offload, mark port
authorized and state completion only if the driver advertizes authorized
state in the connect event. Otherwise there are fair chances of the
driver port authorization API getting called while 4-way handshake is in
progress at the lower layer.
In order to avoid this possible race condition always update port
authorization and supplicant state WPA_COMPLETED setting from
EVENT_PORT_AUTHORIZED context when the driver is done with the 4-way
handshake.
Signed-off-by: Vinayak Yadawad <vinayak.yadawad@broadcom.com>
Add the support of multiple domains for interworking credentials in
D-Bus API AddCred() using an array of strings.
Signed-off-by: Damien Dejean <damiendejean@chromium.org>
Fix compilation issue when using the following build parameter:
CONFIG_CTRL_IFACE=udp-remote
Fixes: 0aae045af0 ("ctrl: Print the source address of the received commands")
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Until now Hotspot 2.0 credentials were only supporting one home OI (with
roaming_consortium option) and one required home OI (with
required_roaming_consortium option). To improve the compliance with
Passpoint specification, add the support for multiple home and required
OIs.
The lists of OIs are provided using two new configuration options
home_ois and required_home_ois that expect a list of OIs formatted as
the roaming_consortiums list. It allows to keep the old options to avoid
breaking currently running configurations and better fits the vocabulary
used in the spec.
The OI match algorithm is updated to implement the behavior described in
Passpoint specification v3.2 section 9.1.2 (Home OIs nodes description
PerProviderSubscription/<X+>/HomeSP/HomeOIList/<X+>).
Signed-off-by: Damien Dejean <damiendejean@chromium.org>
There is no way to create or remove a virtual interface with
wpa_supplicant dbus methods. The platform has to use out-of-band methods
to manage the virtual interfaces.
This change adds virtual interface create/remove logic to the dbus
methods CreateInterface and RemoveInterface to achieve similar
functionalities as wpa_cli commands interface_add and interface_remove.
Signed-off-by: Jintao Lin <jintaolin@chromium.org>
Need to copy own address and peer address locally and pass them to
pasn_deauthenticate(), because this pointer data will be flushed from
the PTKSA cache before sending the Deauthentication frame and these
pointers to then-freed memory would be dereferenced.
Fixes: 24929543 ("PASN: Deauthenticate on PTKSA cache entry expiration")
Signed-off-by: Vinay Gannevaram <quic_vganneva@quicinc.com>
Map to correct control interface commands for PASN start and stop.
Fixes: ad338cfe58 ("ctrl_iface: Add support for PASN authentication")
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
wpa_supplicant used the WPS IE from a Probe Response frame, if one was
received, even if there might have been a more recent Beacon frame with
an updated WPS IE. This could result in using stale information about
active WPS registrar, e.g., when operating on the 6 GHz band.
Prefer WPS IE from a Beacon frame over the default selection of Probe
Response frame (if one has been received) in cases where the Beacon
frame is received more recently than the Probe Response frame and active
WPS Registrar information is being checked. Skip this for the case where
UUID-E is needed since that is not available in the Beacon frame.
Signed-off-by: Sai Pratyusha Magam <quic_smagam@quicinc.com>
OCV cannot be used without PMF and such a configuration were to be used
with wpa_supplicant, the AP would reject the association. hostapd is
already enabling PMF automatically whenever OCV is being enabled, so do
the same with wpa_supplicant.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
If a higher priority BSS has invalid security parameters, e.g., an
invalid SAE password, and a lower priority BSS is discovered only after
the local network profile has been temporarily disabled, the BSSID
ignoring mechanism is not sufficient to allow the lower priority BSS to
be tried and all consecutive attempts will continue to use the higher
priority BSS. This might prevent connection in some unexpected cases
with invalid network configuration.
Extend BSSID ignoring mechanism to work in this type of a case by
ignoring the BSSID that resulted in disabling the SSID temporarily
during the first connection attempt after having re-enabled the SSID.
This allows a lower priority BSS, if any is available in scan results,
to be tried next to see if it might have working security parameters.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Fix memory leak of intro.peer_key in wpas_dpp_rx_peer_disc_resp(). The
other code paths were updated to use dpp_peer_intro_deinit(), but this
non-privacy-protection version of the station implementation was missed.
Fixes: 148de3e0dc ("DPP3: Private Peer Introduction protocol")
Signed-off-by: Glenn Strauss <gstrauss@gluelogic.com>
This is needed to avoid trying the subsequent connections with the old
PMKID that the AP claims not to hold and continues connection failures.
This was already handled for the SME-in-the-driver case in commit commit
50b77f50e8 ("DPP: Flush PMKSA if an assoc reject without timeout is
received"), but the wpa_supplicant SME case did not have matching
processing.
Add the needed check to avoid recover from cases where the AP has
dropped its PMKSA cache entry. Do this only based on the specific status
code value (53 = invalid PMKID) and only for the PMKSA entry that
triggered this failure to minimize actions taken based on an unprotected
(Re)Association Response frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
This prevents attempts of trying to use PMKSA caching when the existing
entry was created using a different MAC address than the one that is
currently being used. This avoids exposing the longer term PMKID value
when using random MAC addresses for connections.
In practice, similar restriction was already done by flushing the PMKSA
cache entries whenever wpas_update_random_addr() changed the local
address or when the interface was marked down (e.g., for an external
operation to change the MAC address).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is needed to be able to determine whether a PMKSA cache entry is
valid when using changing MAC addresses. This could also be used to
implement a mechanism to restore a previously used MAC address instead
of a new random MAC address.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Using separate variables for BSSID and peer address is needed to support
Wi-Fi Aware (NAN) use cases where the group address is used as the BSSID
and that could be different from any other peer address. The
infrastructure BSS cases will continue to use the AP's BSSID as both the
peer address and BSSID for the PASN exchanges.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Rename struct pasn_data::bssid to peer_addr to be better aligned with
different use cases of PASN and its extensions. This is a step towards
having option to use different peer address and BSSID values for NAN use
cases.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
wpa_supplicant has support for only a single FT key hierarchy and as
such, cannot use more than a single mobility domain at a time. Do not
allow FT protocol to be started if there is a request to reassociate to
a different BSS within the same ESS if that BSS is in a different
mobility domain. This results in the initial mobility domain association
being used whenever moving to another mobility domain.
While it would be possible to add support for multiple FT key hierachies
and multiple mobility domains in theory, there does not yet seem to be
sufficient justification to add the complexity needed for that due to
limited, if any, deployment of such networks. As such, it is simplest to
just prevent these attempts for now and start with a clean initial
mobility domain association.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
During cross SSID roaming wpa_supplicant ended up using the default
RSNE/RSNXE in EAPOL-Key msg 2/4 though the driver indicated
(Re)Association Request frame elements without RSNE/RSNXE. This causes
RSNE/RSNXE mismatch between (Re)Association Request frame and EAPOL-Key
msg 2/4.
To avoid this skip copying the default RSNE/RSNXE if the driver
indicates the actually used (Re)Association Request frame elements in
the association event.
Signed-off-by: Utkarsh Soni <quic_usoni@quicinc.com>
Passphrases/PSKs from external password databases were ignored if 4-way
handshake offloading was supported by the driver. Split the PSK loading
functionality into a separate function and calls if to get the PSK for
handshake offloading.
I tested connecting to a WPA2-PSK network with both inline and external
passphrases, using the iwlwifi and brcmfmac drivers.
Signed-off-by: Ben Wolsieffer <benwolsieffer@gmail.com>
In a system with multiple interfaces, the boot messages as well as the
status information provided by `systemctl` can be confusing without
an immediate way to differentiate between the different interfaces.
Fix this by adding the interface name to the unit description.
Signed-off-by: Gioele Barabucci <gioele@svario.it>
The received frame buffer was already verified to be long enough to
include the Advertisement Protocol element and that element was verified
to have a valid length value, but use of adv_proto[1] in another
function may have been too difficult to figure out for analyzers.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add support to specify a Link ID for set key operation for MLO
connection. This does not change the existing uses and only provides the
mechanism for extension in following commits.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Update the following MLO connection information to wpa_sm:
- AP MLD address and link ID of the (re)association link.
- Bitmap of requested links and accepted links
- Own link address for each requested link
- AP link address, RSNE and RSNXE for each requested link
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Currently, PMK parameters in the WPA state machine are set from
configuration only when the interface is initialized. If those
parameters are changed later via D-Bus, the new values don't have any
effect.
Call wpa_sm_set_param() when PMK-related D-Bus properties are changed
to immediately apply the new value; the control interface also does
something similar.
Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
Add the `sae_check_mfp` global option to limit SAE when PMF will
not be selected for the connection.
With this option SAE is avoided when the hardware is not capable
of PMF due to missing ciphers.
With this option SAE is avoided on capable hardware when the AP
does not enable PMF.
Allows falling back to PSK on drivers with the
WPA_DRIVER_FLAGS_SAE capability but do not support the BIP cipher
necessary for PMF. This enables configurations that can fall back
to WPA-PSK and avoid problems associating with APs configured
with `sae_require_mfp=1`.
Useful when `pmf=1` and `sae_check_mfp=1` are enabled and networks
are configured with ieee80211w=3 (default) and key_mgmt="WPA-PSK SAE".
In this configuration if the device is unable to use PMF due to
lacking BIP group ciphers it will avoid SAE and fallback to
WPA-PSK for that connection.
Signed-off-by: Jeffery Miller <jefferymiller@google.com>
Stop listen mode if there is not sufficient time remaining to complete
the Authentication exchange within the current remain-on-channel
operation. This speeds up the operation and avoids some timeouts that
could prevent the provisioning step from completing. This addresses an
issue that was found in the following test case sequence:
dpp_controller_relay_discover dpp_chirp_ap_5g
Similar mechanism was already used for Reconfig Announcement frames, so
reuse that for this case with Presence Announcement frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
When scanning for a new connection, we currently optimize by scanning
all frequencies only when our MCC capabilities will allow an additional
operating frequency, and scan only the existing operating frequencies
otherwise. This is problematic when there the current operating
frequency singularly accounts for one of the shared radio frequencies
because we should be able to switch operating frequencies without adding
to the channel count. Fix this.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
Connection attempt could have been intermittently drop when reconnecting
to the same ESS due the current BSS entry getting removed immediately
after the disconnection for the purpose of reconnecting to the same ESS.
Avoid this by not removing a BSS entry for the same ESS when in this
special state of trying to reconnect to the same ESS.
Signed-off-by : WooYong Kim <wykim@newratek.com>
