Add some more functionality for BSS Transition Management:
- advertise support for BSS Transition Management in extended
capabilities element
- add hostapd.conf parameter bss_transition=1 for enabling support
for BSS Transition Management
- add "hostapd_cli disassoc_imminent <STA> <num TBTTs>" for sending
disassociation imminent notifications for testing purposes
- wpa_supplicant: trigger a new scan to find another BSS if the
current AP indicates disassociation imminent (TODO: the old AP needs
to be marked to use lower priority to avoid re-selecting it)
Signed-hostap: Jouni Malinen <j@w1.fi>
hostapd can run with different VIF when using nl80211. Events about MIC
failures have to be processed in context of the VIF which received it
and not in context of the primary VIF. Otherwise the station belonging
to this VIF may not be found in the primary VIF station hash and
therefore no countermeasures are started or the countermeasures are
started for the wrong VIF.
Signed-hostap: Sven Eckelmann <sven@open-mesh.com>
Signed-hostap: Simon Wunderlich <simon@open-mesh.com>
The WNM-Sleep Mode handler took over WNM Action frame processing without
addressing the previously implemented WNM handler. Fix this by moving
the BSs Transition Management processing into wnm_sta.c to share a
single handler function for WNM Action frames.
Signed-hostap: Jouni Malinen <j@w1.fi>
There is no need for p2p_supplicant.c to access wpa_s->pending_action_tx
so move these references to offchannel.c to get a bit cleaner interface
between the components.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 1ff733383f added a mechanism to
work around issues due to association events and EAPOL RX events being
getting reordered. However, this applied only for the case where
wpa_supplicant is not in associated state. The same issue can happen in
roaming case with drivers that perform BSS selection internally (or in
firmware). Handle that case similarly by delaying received EAPOL frame
processing if the source address of the EAPOL frame does not match the
current BSSID.
Since wired IEEE 802.1X do not have BSSID, make this additional
workaround conditional on BSSID match having been observed during the
previous association.
This fixes issues where the initial EAPOL frame after reassociation was
either dropped (e.g., due to replay counter not increasing) or replied
to with incorrect destination address (the BSSID of the old AP). This
can result in significantly more robust roaming behavior with drivers
that do not use wpa_supplicant for BSS selection.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Network blocks are disabled during a WPS provisioning step and 10
seconds after this to allow the newly provisioned network to be
selected. The disabled=1 flag gets written to the configuration file
when the credential is added since it happens during this process.
Update the file again after the networks have been re-enabled to avoid
leaving the configuration file into state that is not consistent with
the running configuration.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 17a4734dc4 shall optimize the
post-WPS scan based on the channel used during the provisioning only
when the EAP-Failure frame is received. In cases where the EAP-Failure
frame is missed, this optimization shall not happen resulting in the
scan in all the channels thus consuming more time for the connection.
This commit enhances this by storing the requisite information after
the M8 frame is received.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This optional attribute may make it easier to bind together the
Access-Request and Accounting-Request messages. The accounting session
identifier is now generated when the STA associates instead of waiting
for the actual session to start after successfull authentication.
Signed-hostap: Jouni Malinen <j@w1.fi>
Requires Linux kernel patch to make the SGI-20 properly disabled. SGI-40
will already work since Linux 3.4 or so.
Signed-hostap: Ben Greear <greearb@candelatech.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Basic support for the 60 GHz band. Neither P2P nor WPS are yet taken
care off. Allows to start AP with very simple config:
network={
ssid="test"
mode=2
frequency=60480
key_mgmt=NONE
}
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_cancel did not properly cancel a pending p2p_connect-join operation.
Address the different steps in that process: initial scan, Provision
Discovery exchange before connection, and WPS provisioning step
(including the scans before WPS).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the NAI Realm list indicates that EAP-PEAP is used, use EAP-MSCHAPv2
as the Phase 2 method by default if the NAI Realm list does not specify
the tunneled method.
Signed-hostap: Jouni Malinen <j@w1.fi>
The config says that the default for ap_table_max_size is 255 and the
default for ap_table_expiration_time is 60. But the code doesn't reflect
the default values mentioned in the sample config file.
These variables completely disable the code for Overlapping Legacy BSS
Condition by default when they are not correctly initialized. WFA
certification requires this feature and therefore an AP would have
failed the certification process unless they were initialized manually
using the configuration file.
Signed-hostap: Sven Eckelmann <sven@open-mesh.com>
Signed-hostap: Simon Wunderlich <simon@open-mesh.com>
Same fix as d49ea68284 in
wpa_supplicant.
From original commit:
wpa_supplicant is started from /init.*.rc on Android and that seems
to be using umask 0077 which would leave the control interface
directory without group access. This breaks things since Wi-Fi
framework assumes that this directory can be accessed by other
applications in the wifi group. Fix this by adding group access even
if umask value would prevent this.
Signed-hostap: Pontus Fuchs <pontus.fuchs@gmail.com>
If ctrl_interface_group in the config file is set hostapd tries to
chown the dir and socket to uid 0. This causes the chown to fail
if hostapd is run as non-root.
Signed-hostap: Pontus Fuchs <pontus.fuchs@gmail.com>
WSC IE in Beacon and Probe Response frames should behave consistently
as far as the RF Bands attribute is concerned. Use the same dualband
condition for adding this into Probe Response frames since the value
is not really needed if the AP is not a dualband AP.
Signed-hostap: Jouni Malinen <j@w1.fi>
If separate hostapd processes are used for different RF bands, the
dualband parameter for WPS was not set correctly. Allow dualband
indication (mainly, addition of RF bands attribute for PBC session
overlap detection) also based on wps_rf_bands value (if set to "ag").
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit e99b4f3a14 added functionality to
check whether the current association is with the home SP. This commit
did not take into account that the domain name ANQP information could be
NULL and that could result to a NULL pointer dereference. Fix that by
validation that domain_names != NULL before calling
domain_name_list_contains().
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows Probe Request frame processing to compare the configured
SSID to the SSID List element in addition to the SSID element.
Signed-hostap: Jouni Malinen <j@w1.fi>
Replace CONFIG_IEEE80211V with CONFIG_WNM to get more consistent build
options for WNM-Sleep Mode operations. Previously it was possible to
define CONFIG_IEEE80211V without CONFIG_WNM which would break the build.
In addition, IEEE 802.11v has been merged into IEEE Std 802.11-2012 and
WNM is a better term to use for this new functionality anyway.
Signed-hostap: Jouni Malinen <j@w1.fi>
These fields do not use AES keywrap. Instead, they are protected with
management frame protection (and not included if PMF is disabled).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed to allow capture files from the mac80211 cooked monitor
mode interface to be processed properly. Without this, the locally
generated frames may not get processed.
Signed-hostap: Jouni Malinen <j@w1.fi>
The optional tfs_req=<hex dump> parameter can be added for the wnm_sleep
command to specify the TFS request element to use in the WNM-Sleep Mode
Request frame.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This code was within ifdef CONFIG_AP and did not get included unless
AP mode support was also enabled.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
