Do not try to use variables that are not defined without
CONFIG_IEEE80211R=y and add the forgotten "inline" for the function
wrapper.
Fixes: 5c65ad6c0b ("PASN: Support PASN with FT key derivation")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add support to parse MLO connection information from
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_MLO_LINKS for
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH event.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add support for parsing MLO KDEs as defined in Table 12-10 (KDE
selectors) in IEEE P802.11be/D2.0.
Signed-off-by: Rohan Dutta <quic_drohan@quicinc.com>
Co-authored-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add a new vendor sub-command to implement Spatial Reuse feature.
Userspace enables SR feature with specific configuration parameters. The
driver/firmware upon receiving the command, enables the SR feature if it
is supported by the currently connected AP. The driver may reject the
command if it cannot enable the SR with the configured parameters. The
driver sends events to userspace to indicate when SR feature is enabled
or disabled internally. Userspace can also query SR feature related
parameters and statistics from the driver/firmware as needed.
Signed-off-by: Rachit Kankane <quic_rkankane@quicinc.com>
Signed-off-by: Aleti Nageshwar Reddy <quic_anageshw@quicinc.com>
Fix the following compiler error:
qca-vendor.h:5892:54: error: result of ‘1 << 31’ requires 33 bits to represent, but ‘int’ only has 32 bits [-Werror=shift-overflow=]
5892 | QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40INTOL = 1 << 31,
This "1" needs to be marked unsigned for this case of MSB=1.
Signed-off-by: Chaoli Zhou <quic_zchaoli@quicinc.com>
hostapd based automatic channel selection doesn't update the hardware
mode after the channel is selected. This change specifically helps
channel 14 which can operate only in IEEE 802.11b mode.
Signed-off-by: Sunil Ravi <sunilravi@google.com>
bss->conf->bssid may be kept unset and will cause an empty BSSID field
in RNR. Fix this to use own_addr instead.
Signed-off-by: Shay Bar <shay.bar@celeno.com>
Signed-off-by: moran.daori <moran.daori@celeno.com>
The ACS info messages frequently appear for multiple channels. Without
the actual frequency in the messages, they are not very informative.
Add the frequency to them to improve this.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Don't select channels designated for exclusive indoor use when the
country string is set for outdoor operation (country3=0x4f, i.e., the
third character of the country string is 'O').
Signed-off-by: David Bauer <mail@david-bauer.net>
Add a new attribute QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_SP_START_OFFSET to
configure offset to shift start of the service period. This attribute
will be used when device supports flexible TWT. If provided, this
attribute will override QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_WAKE_TIME.
Signed-off-by: nakul kachhwaha <quic_nkachhwa@quicinc.com>
Parse link id info from channel switch events and indicate the info to
control interface using new per link channel switch events. If channel
switch happens on the link which used during association both legacy
and new per-link channel switch events will be reported.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add support to fetch and indicate per-link MLO signal poll information
via a new control interface command MLO_SIGNAL_POLL.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add bssid as parameter to nl80211_get_link_signal() instead of using
bssid from driver structure. This is useful for calling the function
per-MLO link.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add a utility function to fetch Multi-Link Device (MLD) address from a
Basic Multi-Link element.
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
Use AP MLD address as the peer's MAC address to set supplicant port as
authorized for MLO connection.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add support to fetch MLO connection info from the driver to the
wpa_supplicant instance of corresponding MLD STA interface. In addition,
return true for BSSs associated with MLO links from wpa_bss_in_use() to
avoid getting them cleared from scan results.
Co-authored-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
Parse NL80211_ATTR_MLO_LINKS in NL80211_CMD_CONNECT event and cache the
MLO connection information. Set the legacy connection fields such as
assoc_freq and bssid to the values of the MLO link on which association
happened.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Define the following fields described in IEEE P802.11be/D2.1:
- Multi-Link element types as defined in Table 9-401c (Type subfield
encoding)
- Basic Multi-Link element presence bitmap as defined in Figure
9-1002g (Presence Bitmap subfield of the Basic Multi-Link element
format)
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
P2P connections in the 6 GHz band should be limited to preferred
scanning channels since AP/GO discovery cannot depend on 2.4/5 GHz
discovery.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Support updating the RRM IEs to the driver for Probe Response and
(Re)Association response frames in the AP mode when the SME is
implemented in the driver.
Signed-off-by: Chaoli Zhou <quic_zchaoli@quicinc.com>
Set TWT responder configurator in the driver parameters only when the AP
is configured with HE enabled. This was already done for the extended
capability bit generation in commit 8de0ff0fa1 ("HE: Add TWT responder
extended capabilities field"), but this parameter for the driver command
to start the AP in _ieee802_11_set_beacon() missed the condition.
Move the ieee80211ax check into the common helper function to cover both
cases. In addition, add a check for disable_11ax to cover the case where
HE is disabled for a specific BSS.
Fixes: ab8c55358e ("HE: Dynamically turn on TWT responder support")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Extend attributes of subcmd QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO
for quering per MCS TX and RX packets from the driver/firmware.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a new QCA vendor attribute to configure the periodic sounding for Tx
beamformer functionality.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Do not complain about unprotected Action frames for additional
categories that have been defined as not being Robust.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Verify that the MAC Address KDE includes enough data to contain a MAC
address as a part of the parsing function so that each caller would not
need to verify this separately. None of the existing users of this
parser actually needed the MAC address value, so there was not any use
for the length field before. The updated design is more robust for
future uses and gets rid of that unused length field as well.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
When an entry is added to the PTKSA cache, timer expiration is not set.
Check the list and set the timer expiration when the list is empty also.
When another entry is added to the list, it is placed before the relavant
entry in the order of expiry time of all entries present in the list.
Fixes: a4e3691616 ("WPA: Add PTKSA cache implementation")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
After the secure association and PTK derivation are completed, if the
device supports LTF keyseed, generate the LTF keyseed using KDK and set
the ranging context to the driver by using the command
QCA_NL80211_VENDOR_SUBCMD_SECURE_RANGING_CONTEXT.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
AP as a responder, on successful completion of PASN authentication
configures the required keys by using the command
QCA_NL80211_VENDOR_SUBCMD_SECURE_RANGING_CONTEXT to the driver.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This defines the QCA vendor interface functions to offload PASN
authentication from the driver.
The driver sends the QCA_NL80211_VENDOR_SUBCMD_PASN event requesting to
perform PASN authentication with a list of peers with which the driver
needs to do ranging. wpa_supplicant performs PASN handshake with all the
peer devices and sets the required keys using the command
QCA_NL80211_VENDOR_SUBCMD_SECURE_RANGING_CONTEXT to the driver. After
PASN handshake is completed with all requested peers, wpa_supplicant
sends consolidated status for all peers to the driver.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
To support secure ranging with a random MAC address, PASN handshake is
performed with a different source MAC address from the device's own
interface address. Hence, allow PASN Authentication frames with any
foreign MAC address to further process the Authentication frames.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add an option for an alternative processing of PTKSA life time expiry.
Register a callback in wpa_supplicant to handle the life time expiry of
the keys in PTKSA cache. Send PASN deauthentication when a PTKSA cache
entry expires.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This brings in the function declarations and data structures that are
required for handling PASN request from the driver, sending secure
ranging context and PASN response to the driver.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a function to derive the LTF keyseed from KDK. This function is
built only in case that CONFIG_PASN is enabled at build time.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
On successful PASN handshake or 4-way handshake with a peer, PTK is
derived using the local and peer MAC addresses as input. Store the own
MAC address that is used for key derivation in PTKSA cache to maintain
that state over potential MAC addresses changes.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Use separate capabilities for AP and STA modes for P802.11az security
parameters secure LTF support, secure RTT measurement exchange support,
and protection of range negotiation and measurement management frames
support.
P802.11az security parameters are considered to be supported for both
station and AP modes if the driver sets NL80211_EXT_FEATURE_SECURE_LTF,
NL80211_EXT_FEATURE_SECURE_RTT, and
NL80211_EXT_FEATURE_PROT_RANGE_NEGO_AND_MEASURE flags. The driver can
advertize capabilities specific to each mode using
QCA_WLAN_VENDOR_FEATURE_SECURE_LTF*,
QCA_WLAN_VENDOR_FEATURE_SECURE_RTT*, and
QCA_WLAN_VENDOR_FEATURE_PROT_RANGE_NEGO_AND_MEASURE* flags.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This fixes the build with OpenSSL 1.1.1:
../src/crypto/crypto_openssl.c: In function 'crypto_rsa_oaep_sha256_decrypt':
../src/crypto/crypto_openssl.c:4404:49: error: 'RSA_PKCS1_OAEP_PADDING' undeclared (first use in this function)
Signed-off-by: Andre Heider <a.heider@gmail.com>
Reorder PKEX initiation function to send out the PKEX Exchange Request
frame at the end after all possible error cases have been checked. This
prevents Enrollee from seeing a PKEX frame when the session is about to
fail.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add QCA_NL80211_VENDOR_SUBCMD_GET_SAR_CAPABILITY to get various SAR
capabilities supported by the WLAN firmware to userspace. These
capabilites are usually reported by the firmware during the initial
bootup handshake with the driver. Based on these capabilities, user
space can choose proper SAR indexes.
Signed-off-by: Mukul Sharma <quic_mukul@quicinc.com>
Add support to configure SAE, PSK, and PSK-SHA256 AKMs in connect
request when driver's SME in use. This is needed for implementing
WPA3-Personal transition mode correctly with any driver that handles
roaming internally.
Send additional AKMs configured in network block to driver based on
the maximum number of AKMs allowed by driver in connect request. Keep
first AKM in the list AKMs in the connect request as AKM selected by
wpa_supplicant to maintain backwards compatibility.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Use the recently added attribute to determine whether the kernel
supports a larger number of AKM suites in various commands.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
This brings in nl80211 definitions as of 2022-07-22. In addition, update
nl80211_command_to_string() to cover the new defined commands.
Signed-off-by: Jouni Malinen <j@w1.fi>
hostapd_dpp_add_controller() ended up trying to parse the IP address
without nul terminating it. This might work with some C libraries, but
not all. And anyway, this was already supposed to nul terminate the
string since a temporary copy is created of the constant string. Fix
this by adding the missed replacement of the space with nul.
Fixes: bfe3cfc382 ("DPP: Allow Relay connections to Controllers to be added and removed")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
u64 needs "long long unsigned int" on 32-bit, so print this using a
typecase value so that both 32 and 64-bit builds work fine.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
EVP_PKEY_derive() might report a larger maximum size of the output than
HPKE_MAX_SHARED_SECRET_LEN under some conditions. That should be allowed
as long as the real final length is within the maximum limit.
Furthermore, since we are using a fixed length buffer for this, there is
no need to call EVP_PKEY_derive() twice to first learn the maximum
length. Use a bit longer buffer and allow OpenSSL to take care of the
update to the final length internally with than single call.
This showed up using the following test case sequence:
dbus_pkcs11 dpp_private_peer_introduction
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This can be helpful for upper layers to be able to determine whether the
configuration was rejected.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Enhance QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH event for the
driver to indicate the information of the associated links of MLO
roaming.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
The initial timeout of 10 seconds for the first scan before knowing
whether the driver reports scan completion events may not be sufficient
in cases where the driver ends up scanning a large number of channels.
In particular, this could be hit with 6 GHz support. Increase this
timeout when the driver indicates support for 6 GHz channels.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The <openssl/buf.h> include is relevant in both OpenSSL and BoringSSL
because the file uses BUF_MEM (include what you use). OpenSSL just
happened to include it via another file. OpenSSL also spells it
<openssl/buffer.h>, not matching the type, so use the compatible
spelling.
Additionally all the CHECKED_CAST and manual STACK_OF(T) definitions
call into BoringSSL internals. The correct, public APIs are simply to
just use the same code as OpenSSL and call the DEFINE_STACK_OF macros.
Signed-off-by: David Benjamin <davidben@google.com>
Commit 74818ca63f ("Process
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH after NL80211_CMD_ROAM")
added workaround to hold the pending
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH event data for up to 100 ms
in case NL80211_CMD_ROAM is not received first. The 100 ms wait period
was sufficient for most of the cases but it's observed that some times
kernel is taking more than 100 ms to process and send NL80211_CMD_ROAM
to userspace.
If NL80211_CMD_ROAM takes more than 100 ms
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH event data getting ignored
though wpa_supplicant has it. To avoid this remove timeout for
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH event data since driver
always indicates NL80211_CMD_ROAM along with
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH.
In addition, clear the pending event data when marking the interface
disconnected since the roaming information is supposed to be used only
when reassociating without a disconnection.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Previously when chains of BT and WLAN 2.4 GHz are separated,
hybrid mode will be used for BTC. Now adding fixed FDD mode
to fulfill different BTC scenarios.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The Enrollee may report its supported curves in the bootstrapping URI.
If it does that, the Configurator may stop generating the Config Object
that would depend on the Enrollee using a curve that it did not indicate
as being supported. Check for this case while proessing the Config
Request and stop Configurator from building a configuration that is
known not to work.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Select the PMK length based on the used group (prime length) when using
the new AKM suites for SAE.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
SAE authentication needs to known which AKM suite is being used to be
able to determine the correct PMK length for the new AKM suite selectors
that use variable length keys.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The new SAE AKM suites are defined to use H2E, so ignore the sae_pwe
value when these AKM suites are used similarly to the way H2E gets
enabled when SAE Password Identifiers are used.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Update the AKM suite specific mapping of various EAPOL-Key key lengths
and algorithms to include the new SAE AKM suites with variable length
keys.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Define new WPA_KEY_MGMT_* values for the new SAE AKM suite selectors
with variable length keys. This includes updates to various mapping and
checking of the SAE key_mgmt values.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Use the existing helper function instead of maintaining multiple copies
of lists of SAE key management suites.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The new DPP-RELAY-NEEDS-CONTROLLER control interface event can be used
to trigger mDNS discovery of a Controller to see if such a connection
can be established automatically at the time an Enrollee is trying to
initiate an operation.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The new control interface commands "DPP_RELAY_ADD_CONTROLLER <IP addr>
<PK hash>" and "DPP_RELAY_REMOVE_CONTROLLER <IP addr>" can now be used
to dynamically add and remove connections to Controllers for the cases
where the connection is initialized through a DPP Public Action frame
(i.e., Controller as the Responder).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Instead of requiring explicit configuration through
dpp_configurator_connectivity=1, advertise Configurator connectivity
automatically if a Relay is configured with a Controller that can
operate as a Responder.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Accept an incoming TCP connection from a Controller in a Relay that is
configured with dpp_relay_port even if that Controller is not configured
with a dpp_controller parameter. This allows more dynamic Controller
initiated operations, e.g., when using mDNS to discover a Relay.
This type of a dynamic Controller entry will not be used for exchanges
that are initiated by an Enrollee (i.e., based on a DPP Public Action
frame received by the Relay).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Verify that the peer does not change its bootstrapping key between the
PKEX exchange and the authentication exchange.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
When PKEX was started through the push button mechanism, the own
bootstrapping key was not bound correctly to the Authentication phase
information and that ended up in incorrectly generating a new
bootstrapping key for the Authentication exchange. Fix this by added the
needed own=<id> parameter into the cached parameters when using push
button.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The peer=<id> information about the specific boostrapping key provided
through PKEX was added for Public Action frame cases, but the TCP
variant did not do same. Add the same information there to maintain
knowledge of the specific peer bootstrapping key from PKEX to
Authentication exchange.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Extend DPP push button support in wpa_supplicant to allow the role of
the Configurator to be used. This provides similar functionality to the
way the DPP_PUSH_BUTTON command in hostapd worked when providing the
configuration parameters with that command (instead of building the
config object based on current AP configuration).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
It is possible for a Controller to receive a copy of its own PKEX
Exchange Request in the case where the Controller is initiating a PKEX
exchange through a Relay. The Configurator role in the device would have
a matching PKEX code in that case and the device might reply as a PKEX
responder which would result in going through the exchange with the
Controller device itself. That is clearly not desired, so recognize this
special case by checking whether the Encrypted Key attribute value
matches a pending locally generated one when processing a received PKEX
Exchange Request.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This gets the Controller (DPP-over-TCP) sequence closer to the one used
with Public Action frames and makes it easier for upper layer components
to share the same design for tracking operation status.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Relay will need to allow the PKEX Exchange Response message to be
handled similarly to the Authentication Response message to allow this
sequence to be completed successfully.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
We are not supposed to reuse these without being explicitly requested to
perform PKEX again. There is not a strong use case for being able to
provision an Enrollee multiple times with PKEX, so this should have no
issues on the Enrollee. For a Configurator, there might be some use
cases that would benefit from being able to use the same code with
multiple Enrollee devices, e.g., for guess access with a laptop and a
smart phone. That case will now require a new DPP_PKEX_ADD command on
the Configurator after each completion of the provisioning exchange.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a privacy protecting variant of the peer introduction protocol to
allow the station device to hide its Connector from 3rd parties. The new
wpa_supplicant network profile parameter dpp_connector_privacy=1 can be
used to select this alternative mechanism to the peer introduction
protocol added in the initial release of DPP.
It should be noted that the new variant does not work with older DPP APs
(i.e., requires support for release 3). As such, this new variant is
disabled by default.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add support for HPKE base mode with single-shot API (see RFC 9180) using
OpenSSL. This is needed for DPP private introduction protocol.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This allows the DPP Configuration Object from a Configurator to be
extended with 3rd party information. This information can be provided as
a part of the existing configuration specification mechanisms with the
new extra_name=<string> and extra_value=<hexdump encoded JSON>.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This allows the DPP Configuration Request Object from an Enrollee to be
extended with 3rd party information. The new dpp_extra_conf_req_name and
dpp_extra_conf_req_value configuration parameters specify the name of
the added JSON node and its contents. For example:
dpp_extra_conf_req_name=org.example
dpp_extra_conf_req_value={"a":1,"b":"test"}
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a new vendor subcommand QCA_NL80211_VENDOR_SUBCMD_SCS_RULE_CONFIG
for configuration event of Stream Classification Service (SCS) rule.
Also define the attributes present in this subcommand.
Signed-off-by: Harsh Kumar Bijlani <quic_hbijlani@quicinc.com>
Add a new vendor attribute QCA_WLAN_VENDOR_ATTR_CONFIG_DBAM to
configure Dedicated Bluetooth Antenna Mode (DBAM). It is used to
switch between dedicated antenna mode for BT and COEX shared
antenna mode for WLAN and BT.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This extends Relay functionality to allow a Controller to intitiate a
new DPP exchange in addition to the previously supported case where the
exchange was initiated through a DPP Public Action frame.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
While the most likely production use case for DPP push button is to
provision the AP's current configuration, there might be some use cases
for providing different configuration. Add possibility for doing this by
extending the DPP_PUSH_BUTTON command to accept an optional set of
parameters similarly to the other DPP commands for the Configurator.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Allow the Responder/Initiator hash values to be corrupted in Push Button
Presence Announcement messages for testing purposes.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add support to use a push button -based bootstrap mechanism with DPP.
The new DPP_PUSH_BUTTON control interface command enables this mode on
the AP/hostapd and station/wpa_supplicant. This goes through the
following sequence of events: a suitable peer in active push button mode
is discovered with session overlap detection, PKEX is executed with
bootstrap key hash validation, DPP authentication and configuration
exchanges are performed.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add feature capability indication for P802.11az security for the drivers
to advertise capabilities such as secure LTF support, secure RTT
measurement exchange support, and protection of range negotiation and
measurement management frames for station and AP interfaces
independently. This allows a more fine-tuned capability indication as an
alternative to the upstream nl80211 mechanism that is not specific to
the operating mode.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add vendor command QCA_NL80211_VENDOR_SUBCMD_COAP_OFFLOAD to
enable/disable offload processing in firmware for CoAP messages
(RFC7252: The Constrained Application Protocol) or fetch the
CoAP messages cached during offload processing.
Signed-off-by: Yu Wang <quic_yyuwang@quicinc.com>
Add the following two vendor attributes to send TIM beacon
statistics to userspace which can be used for power saving:
QCA_WLAN_VENDOR_ATTR_LL_STATS_TIM_BEACON
QCA_WLAN_VENDOR_ATTR_LL_STATS_TIM_BEACON_ERR
Signed-off-by: Jingxiang Ge <quic_jge@quicinc.com>
Define QCA vendor interface for PASN offload to userspace from the driver.
The driver can send this command as an event to a userspace component to
perform PASN authentication with a list of peers with which the driver
needs to do ranging. The userspace component, if capable of performing
PASN handshake, can perform PASN handshake with all the peer devices and
set the relevant keys by sending the
QCA_NL80211_VENDOR_SUBCMD_SECURE_RANGING_CONTEXT command for each peer
to the driver.
Once PASN handshake is completed with all requested peers, the userspace
component sends consolidated status for all the peers to the driver. The
consolidated report is required for the driver to understand that the
PASN handshake process is complete and whether it succeeded/failed for
each of the peers it was requested for. The secure ranging context is
configured only for the peers with which the PASN handshake succeeded.
When the driver requests PASN keys, the userspace component can set the
keys from its cache if those keys have not already expired and were
derived with the same source MAC address that is requested by the driver
instead of doing the full PASN handshake again.
If the driver detects that current keys of a peer are not valid anymore,
it sends a notification to userspace using the
QCA_NL80211_VENDOR_SUBCMD_PASN command and setting the action to
QCA_WLAN_VENDOR_PASN_ACTION_DELETE_SECURE_RANGING_CONTEXT. The userspace
component should delete the corresponding keys from its cache.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a new QCA vendor attribute
QCA_WLAN_VENDOR_ATTR_CONCURRENT_POLICY_AP_CONFIG to
QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_POLICY sub command to set the
concurrency policy for AP interface.
QCA_WLAN_VENDOR_ATTR_CONCURRENT_POLICY_AP_CONFIG uses the values
defined in enum qca_wlan_concurrent_ap_policy_config to specify
concurrency policy.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
Rename QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_MULTI_STA_POLICY to
QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_POLICY to allow extension for other
interface type(s). A subsequent commit will extend the renamed
definitions in a manner that is inconsistent with the current naming.
This is a precursor for AP/P2P concurrency policy configuration support
via updated vendor command QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_POLICY.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
Move most of CHANWIDTH_* definitions from ieee80211_defs.h to defs.h as
the definitions are getting used mostly for internal purpose only. Also
change prefix of the definitions to CONF_OPER_CHWIDTH_* and update in
all the files accordingly.
Leave the couple of VHT-specific exceptions to use the old defines (the
reason why they were originally added as VHT values), to avoid use of
clearly marked configuration values in information elements. In
addition, use the defines instead of magic values where appropriate.
Signed-off-by: Aleti Nageshwar Reddy <quic_anageshw@quicinc.com>
Add QCA vendor event to indicate user space that the driver recovery is
completed after the internal failure reported with
QCA_NL80211_VENDOR_SUBCMD_HANG.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add a new QCA vendor attribute
QCA_WLAN_VENDOR_ATTR_CONFIG_AUDIO_DATA_PATH to
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION to configure audio data
path.
Possible audio data paths are defined in enum qca_wlan_audio_data_path.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
