The old WPS interface for using NFC has no known deployments and even
the binary libraries referenced here are not easily available anymore.
Since the new interface for using NFC with WPS covers the same
functionality, remove the old implementation to clean up WPS
implementation.
Signed-hostap: Jouni Malinen <j@w1.fi>
This commit adds new wpa_supplicant ctrl_iface commands to allow
external programs to go through NFC connection handover mechanism
with wpa_supplicant taking care of the WPS processing. This version
includes only the case where wpa_supplicant is operating as a
station/Enrollee.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows the P2P_PEER command to be used to fetch the list of
secondary device types that each P2P peer has advertised.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Extend the wpa_cli wps_pin command to support specification of the PIN
expiration time in seconds similarly to hostapd_cli wps_pin command when
using wpa_supplicant for AP mode (including P2P GO).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The bssid and priority parameters in a network block do not have any
effect on the validity of a PMKSA cache entry, so avoid flushing the
PMKSA cache when only these parameters are changed. This is mainly
to allow forced roaming or network selection changes without causing
a disconnection if the changes are done during RSN association that
used EAP.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When specified in the conf file this parameter will make all invocations
of p2p_group_add, p2p_connect, and p2p_invite behave as if "ht40" has
been specified on the command line. This shouldn't do harm since
regulatory constraints and driver capabilities are consulted anyway
before starting HT40 mode.
Signed-hostap: Arik Nemtsov <arik@wizery.com>
External programs can use this new parameter to prevent wpa_supplicant
from connecting to a list of BSSIDs and/or SSIDs. The disallowed BSSes
will still be visible in scan results and it is possible to run ANQP
operations with them, but BSS selection for connection will skip any
BSS that matches an entry in the disallowed list.
The new parameter can be set with the control interface SET command
using following syntax:
SET disallow_aps <disallow_list>
disallow_list ::= <ssid_spec> | <bssid_spec> | <disallow_list> | “”
SSID_SPEC ::= ssid <SSID_HEX>
BSSID_SPEC ::= bssid <BSSID_HEX>
For example:
wpa_cli set disallow_list "ssid 74657374 bssid 001122334455 ssid 68656c6c6f"
wpa_cli set disallow_list
(the empty value removes all entries)
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The ASCII hexdump is somewhat difficult to search for (especially on
Android builds), so make the debug log easier to parse by printing the
full control interface command as a text string. In addition, use
wpa_dbg() to get the interface name printed so that multi-interface
cases can be debugged.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 4d32c0c44d added another use for the
local pos variable and that broke the mechanism used to determine wheter
the peer address was provided. Fix this by using a separate pointer to the
peer address.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is an initial step in allowing the ANQP responses to be shared
among multiple BSSes if the BSSes are determined to be operating under
identical configuration.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the REMOVE_NETWORK command is used to delete the currently connected
network, some operations were run between removing the network and
clearing of wpa_s->current_ssid. This left wpa_s->current_ssid pointing
to freed memory and should any operation end up using it before the
pointer gets cleared, freed memory could be references. Avoid this by
removing the network only after having completed the operations that
clear wpa_s->current_ssid.
Signed-hostap: Deepthi Gowri <deepthi@codeaurora.org>
intended-for: hostap-1
The freq and ht40 parameters can now be used with the p2p_invite
command when reinvoking a persistent group as the GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_cli p2p_serv_disc_req command can now be used to request WSD
request to be sent to specified or all peers who support WSD.
format: wifi-display <list of roles> <list of subelements>
examples:
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source] 2,3,4,5
p2p_serv_disc_req 02:01:02:03:04:05 wifi-display [pri-sink] 3
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [sec-source] 2
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source+sink] 2,3,4,5
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source][pri-sink] 2,3,4,5
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This commit adds control interface commands and internal storage of
Wi-Fi Display related configuration. In addition, WFD IE is now added
to various P2P frames, Probe Request/Response, and (Re)Association
Request/Response frames. WFD subelements from peers are stored in the
P2P peer table.
Following control interface commands are now available:
SET wifi_display <0/1>
GET wifi_display
WFD_SUBELEM_SET <subelem> [hexdump of length+body]
WFD_SUBELEM_GET <subelem>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows both hostapd and wpa_supplicant to be used to derive and
configure keys for GCMP. This is quite similar to CCMP key
configuration, but a different cipher suite and somewhat different rules
are used in cipher selection. It should be noted that GCMP is not
included in default parameters at least for now, so explicit
pairwise/group configuration is needed to enable it. This may change in
the future to allow GCMP to be selected automatically in cases where
CCMP could have been used.
This commit does not included changes to WPS or P2P to allow GCMP to be
used.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new gas_request and gas_response_get commands can be used to request
arbitary GAS queries to be performed. These can be used with ANQP or
with other (including vendor specific) advertisement protocols.
gas_request <BSSID> <AdvProtoID> [Query]
gas_response_get <addr> <dialog token> [offset,length]
For example, ANQP query for Capability list in interactive wpa_cli
session:
> gas_request 02:00:00:00:01:00 00 000102000101
<3>GAS-RESPONSE-INFO addr=02:00:00:00:01:00 dialog_token=0
status_code=0 resp_len=32
> gas_response_get 02:00:00:00:01:00 00
01011c00010102010501070108010c01dddd0c00506f9a110200020304050607
> gas_response_get 02:00:00:00:01:00 00 0,10
01011c00010102010501
> gas_response_get 02:00:00:00:01:00 00 10,10
070108010c01dddd0c00
> gas_response_get 02:00:00:00:01:00 00 20,10
506f9a11020002030405
> gas_response_get 02:00:00:00:01:00 00 30,2
0607
It should be noted that the maximum length of the response buffer is
currently 4096 bytes which allows about 2000 bytes of the response data
to be fetched with a single gas_response_get command. If the response is
longer, it can be fetched in pieces as shown in the example above.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If 4-way handshake fails due to likely PSK failure or if EAP
authentication fails, disable the network block temporarily. Use longer
duration if multiple consecutive failures are seen.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the p2p_find command is used without the delay parameter, a 500 ms
default search delay will now be used when any interface using the same
radio is in an concurrent operation. "p2p_find delay=0" can be used to
enforce the old behavior in such a case if needed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A new optional delay=<search delay in milliseconds> parameter can now be
used with p2p_find command to request an extra delay between search
iterations. This can be used, e.g., to make p2p_find friendlier to
concurrent operations by avoiding it from taking 100% of the radio
resources.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Hotspot 2.0 allows only WPA2-Enterprise to be used, so other types of
networks must not be indicated as Hotspot 2.0 networks even if they
(incorrectly) advertise HS 2.0 support.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add optional "ht40" argument for p2p_group_add command to enable 40 MHz
in 5GHz band. This configures the secondary channel, when HT support is
enabled and if the HW supports 40 MHz channel width.
Signed-hostap: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Allow the user to configure an RSSI threshold in dBm below which the
nl80211 driver won't report scan results. Currently only supported
during scheduled (PNO) scans.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This functionality could be shared for other commands, too, so move
it to a common function. In addition, implement the validation in a
bit more strict way to avoid accepting values like '-123' as a valid
PIN.
Signed-hostap: Jouni Malinen <j@w1.fi>
Reject invalid PIN value in p2p_connect command. Before this, typos
like "pbd" as the third parameter could have resulted in OK return
value since this parameter was interpreted as the PIN.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
WPS_ER_NFC_CONFIG_TOKEN command can now be used to build a NFC
configuration token based on AP Settings learnt with WPS_ER_LEARN
or set with WPS_ER_CONFIG.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new wpa_supplicant ctrl_iface command WPS_NFC_TAG_READ can now be
used to process NFC tags read by external programs to initiate
wpa_supplicant to use NFC Configuration Token to create a new network.
Signed-hostap: Jouni Malinen <j@w1.fi>
Instead of requiring low-level access to an NFC device and synchronous
operations, the new WPS_NFC_TOKEN and WPS_NFC ctrl_iface commands can be
used to build a NFC password token and initiate WPS protocol run using
that token (or pre-configured values) as separate commands. The
WPS_NFC_TOKEN output can be written to a NFC tag using an external
program, i.e., wpa_supplicant does not need to have low-level code for
NFC operations for this.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, a pending scan request could be left running when processing
DISCONNECT command from control interface. This can result in unexpected
scan, so cancel the request to avoid this.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use wpa_supplicant_set_state() to initialize state to DISCONNECT so that
autoscan gets initialized properly. This needs a change in
autoscan_init() to avoid extra scan request that would postpone the
first scan request when an interface is added.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add an additional parameter to prioritize either sta or p2p connection
to resolve conflicts arising during single channel concurrency.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
This is a workaround for interoperability issues with some deployed P2P
implementations that require a Provision Discovery exchange to be used
before GO Negotiation. The new provdisc parameter for the p2p_connect
command can be used to request this behavior without having to run a
separate p2p_prov_disc command.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The nl80211 driver interface does not allow 128-bit WEP to be used
without a vendor specific cipher suite and no such suite is defined for
this purpose. Do not accept WEP key length 16 for nl80211 driver
interface forn ow. wext-interface can still try to use these for
backwards compatibility.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the AP indicates support for Hotspot 2.0, show this in the
ctrl_iface commands for BSS table and status.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Do not try to associate with a network that has an invalid or incomplete
configuration because the association or at least data connection would
fail anyway. This commits adds a common function for checking whether a
network block is disabled to make it easier to check network blocks
without having to reject them during configuration file parsing (which
would prevent wpa_supplicant from starting). The only additional check
added in this commit is to verify the WEP key length. Similar checks for
other parameters can be added in future commits.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 7de5688d68 started using
wpa_supplicant_ctrl_iface_ctrl_rsp_handle() from the D-Bus code, but
left this function in ctrl_iface.c that is included conditionally. Fix
this by moving the common function into wpa_supplicant.c so that it can
be included for builds that include only either ctrl_iface or D-Bus.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
An existing persistent group information can now be used to force GO
Negotiation to use the previously used SSID/passphrase from a persistent
group if we become a GO. This can be used as an alternative to inviting
a new P2P peer to join the group (i.e., use GO Negotiation with GO
intent 15 instead of starting an autonomous GO and using invitation),
e.g., in case a GO Negotiation Request is received from a peer while we
are not running as a GO. The persistent group to use for parameters is
indicated with persistent=<network id> parameter to p2p_connect.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant can now be requested to automatically figure out whether
the indicated peer is operating as a GO and if so, use join-a-group
style PD instead of pre-GO Negotiation PD.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_connect command can now be used with an optional "auto" parameter
to request wpa_supplicant to determine automatically whether to use
join-a-group operation (if the peer is operating as a GO) or group
formation. This makes it easier for external programs to handle
connection type selection by offloading this to wpa_supplicant. The
previously used p2p_connect join commands can be replaced with
p2p_connect auto to use this new mechanism.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This optional parameter to the BSS command can be used to select which
fields are included in the output to avoid having to parse through
unneeded information and to reduce the buffer size.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Enable control of wpa_s->scan_interval via D-Bus. This parameter
controls the delay between successive scans for a suitable AP.
Also, update dbus.doxygen with ScanInterval, and some other
parameters that were undocumented.
Signed-hostap: Mukesh Agrawal <quiche@chromium.org>
There is no need to use reassociation instead of association in a case
the previous connection was explicitly disconnected.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the ctrl_iface SCAN command to be used to run through a scan
to collect full scan results when sched_scan is in progress. sched_scan
will be re-started automatically after the full scan.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Move disassociate and deauthenticate commands to ctrl_iface_ap.c, so
that they ares accessible for wpa_supplicant AP mode and wpa_cli (with
CONFIG_AP option enabled).
Signed-hostap: Jithu Jance <jithu@broadcom.com>
A list of disallowed frequencies for P2P channel list can now be
configured with P2P_SET disallow_freq. The frequencies (or frequency
pairs) are comma separated. For example:
wpa_cli p2p_set disallow_freq 2462,5000-6000
The allowed P2P channel list is constructed by removing explicitly
disallowed channels from the channel list received from the driver.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
New wpa_cli commands list_creds, add_cred, remove_cred, and set_cred
can now be used to manage credentials similarly to the commands used
with network blocks.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant can now be configured to filter out scan results based
on a BSSID filter. Space-separated set of allowed BSSIDs can be set
with wpa_cli set bssid_filter command. Filtering mechanism can be
disabled by setting this variable to an empty list. When set, only
the BSSes that have a matching entry in this list will be accepted
from scan results.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Extra parameter "no-connect" can now be added to the ENABLE_NETWORK
ctrl_iface command to avoid automatic connection to the enabled
network.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"wpa_cli set radio_disabled 1/0" can be used to disable/enable
radio to simulate out-of-radio-range condition in a testbed
device.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The BSS ctrl_iface command can sow the age of a BSS table entry to
make it easier for external programs to figure out whether an entry
is still current depending on the use case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"BSS p2p_dev_addr=<P2P Device Address>" can now be used to fetch a
specific BSS entry based on the P2P Device Address of the GO to avoid
having to iterate through the full BSS table when an external program
needs to figure out whether a specific peer is currently operating as
a GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When a GO is operating a persistent group and invites a peer that has
been a P2P client in that persistent group, the Invitation Type in the
Invitation Request frame can be set to 1 to indicate that this is a
reinvocation of a persistent group. Do this based on the maintained
list of P2P clients that have been provided the credentials to this
group.
Signed-hostap: Jouni Malinen <j@w1.fi>
This will be needed to be able to move ctrl_iface TERMINATING event to
the end of interface removal.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
dev_id=<P2P Device Addr> can now be specified as an argument to
p2p_find to request P2P find for a specific P2P device.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add "persistent=<network id>" line to P2P_PEER ctrl_iface data
if a persistent group credentials are available for this peer.
This makes it easier for external programs to figure out when
a persistent group could be re-invoked with this peer.
For now, this information is only available on the P2P client,
but similar information can be added for GO once a list of P2P
clients is maintained with the persistent group data.
Signed-hostap: Jouni Malinen <j@w1.fi>
The P2P module provides access to public peer data in struct
p2p_peer_info. Use this to build the P2P_PEER information in
ctrl_iface.c instead of providing such text format data from the P2P
module.
The internal data that was previously built in p2p_get_peer_info() as
part of the text format peer data is now available through a separate
p2p_get_peer_info_txt() function. This is still included in P2P_PEER
output to maintain backwards compatibility with external programs that
could have started to use this. However, it should be noted that this
data is not really supposed to be used for anything else apart from
debugging purposes and its format is subject to change.
Signed-hostap: Jouni Malinen <j@w1.fi>
Need to remove ROAM command processing since the needed functionality
for it gets removed with CONFIG_NO_SCAN_PROCESSING=y.
Signed-hostap: Jouni Malinen <j@w1.fi>
The whole wpa_supplicant_ctrl_iface_ctrl_rsp_handle() function operates
on the ssid->eap field which exists only if IEEE8021X_EAPOL has been
defined. Therefore the whole function body needs to be enclosed within
an #ifdef/endif block.
Signed-hostap: Antonio Quartulli <ordex@autistici.org>
Convert core wpa_supplicant code to use u64 instead of void * for the
P2P service discovery reference. Use uintptr_t in type casts in
p2p_supplicant.c to handle the conversion without warnings.
Note: This needs to be revisited for 128-bit CPU where sizeof(void *)
could be larger than sizeof(u64).
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to request Provision Discovery Request to be sent
for the purpose of joining a running group, e.g., to request the GO
to display a PIN that we can then use with p2p_connect join command.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
"wpa_cli status wps" can now be used to fetch the WPA2-Personal
passphrase from AP mode operation with wpa_supplicant to make it
easier to meet WPS requirements for legacy STA support.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When normal scan can speed up operations, use that for the first three
scan runs before starting the sched_scan to allow user space sleep more.
We do this only if the normal scan has functionality that is suitable
for this or if the sched_scan does not have better support for multiple
SSIDs.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"SET pno <1/0>" ctrl_iface command can now be used to start/stop PNO
with sched_scan driver commands. This will request offloading of
scanning to find any of the enabled networks in the configuration.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use capability information to decide whether to perform a given TDLS
operation internally or through mgmt-frame Tx.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
This command allows an external program manage the BSS blacklist
and display its current contents.
Note: The blacklist is considered to be internal mechanism within
wpa_supplicant and changing it can have unexpected results.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This can be used to display the current debugging level and to change
the log level during run time.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This adds the basic mechanism for running through network selection:
scan, ANQP fetch, network selection, and connection. Actual rules for
network selection and the creation of the network block are still
missing, but will be added in separate commits.
Add mechanism for using GAS/ANQP to query Interworking related
information from APs. The received information is stored in the BSS
table and can be viewed with ctrl_iface BSS command.
New ctrl_iface command ANQP_GET can be used to fetch ANQP elements from
a specific AP. Additional commands FETCH_ANQP and STOP_FETCH_ANQP can be
used to initiate and stop an iteration through all APs in the BSS table
that indicate support Interworking to fetch ANQP elements from them.
The P2P specification (3.1.4.3) disallows use of the Label configuration
method between two P2P devices. This was previously enforced at upper
level, but the obsolete code can be removed from wpa_supplicant. This
adds a bit more strict enforcement of the policy, but should not result
in practical differences since no known P2P implementation uses Label
config method.
If a network configuration block is removed or modified, flush
all PMKSA cache entries that were created using that network
configuration. Similarly, invalidate EAP state (fast re-auth).
The special case for OKC on wpa_supplicant reconfiguration
(network_ctx pointer change) is now addressed as part of the
PMKSA cache flushing, so it does not need a separate mechanism
for clearing the network_ctx values in the PMKSA cache.
Make sure that the WPA and EAPOL state machines do not hold a pointer
to a network configuration that is about to be freed. This can fix
potential issues with references to freed memory.
