When controlling multiple virtual interfaces on the same physical
radio, share the scan results events with sibling interfaces. This
decreases the time it takes to connect many virtual interfaces.
This is currently only supported on Linux with cfg80211-based
drivers when using nl80211 or wext driver interface.
Signed-off-by: Ben Greear <greearb@candelatech.com>
wpa_supplicant showed signal levels incorrectly with some drivers:
Jun 6 16:29:36 rupert wpa_supplicant[18945]: Current BSS: 00:0d:97:11:40:d6
level=190
Jun 6 16:29:36 rupert wpa_supplicant[18945]: Selected BSS: 00:0d:97:11:50:09
level=192
Judging from output from other tools (iwlist) and the min_diff block
at the end of wpa_supplicant_need_to_roam, it seems these values
should actually be negative. Specifically, if one treats that number
as a signed char instead of unsigned, everything matches up.
To be honest, I've little to no understanding of wireless, but looking
at the source code for wireless-tools (iw_print_stats in iwlib.c), it
seems that the fields of the iw_quality struct need to be decoded
differently depending on various flags. I guess
src/drivers/driver_wext.c should have similar logic in
wext_get_scan_qual.
I wrote a patch that attempts to replicate some of that logic,
although it may be more complicated than is necessary; I think some of
the complexity is for backwards-compatibility, which might not be
necessary depending on wpa_supplicant's dependencies? In any case, it
is attached. Again, I don't know how any of this works, so it's likely
the patch is a bit off. But I think at least the logic to determine
min_diff in wpa_supplicant_need_to_roam would be more accurate if
level were determined correctly.
Replace use of rfkill block event with rtnetlink ifdown. This makes
the design more robust since the rfkill event could have been for
another interface while the rtnetlink events are already filtered
based of ifindex. In addition, the new design handles other than
rfkill-triggered ifdown/ifup events, too. rfkill unblocked event
is still needed to try to set the interface back up. If the unblock
was for another interface, ifup will fail and the driver state is
not changed.
Add a new wpa_supplicant state: interface disabled. This can be used
to allow wpa_supplicant to be running with the network interface even
when the driver does not actually allow any radio operations (e.g.,
due to rfkill).
Allow driver_nl80211.c and driver_wext.c to start while rfkill is in
blocked state (i.e., when ifconfig up fails) and process rfkill
events to block/unblock WLAN.
If the driver is detected to use cfg80211, we can rely on it being able
to disconnect with SIOCSIWMLME commands and to use empty SSID as a way
to stop it from associating when we are in progress of configuring the
driver for association. Consequently, we can remove the hack that uses
random 32-octet SSID to force disconnection and re-order association
commands to match the expectations that cfg80211 has for WEXT ioctls.
This gets rid of extra scan rounds and attempts to associate with the
silly 32-octet SSID.
Number of Linux driver wrappers included this more or less identical
function, so lets add a new helper file to be able to share some more
code between the driver wrappers.
Network device ifindex will change when the interface is re-inserted.
driver_wext.c will need to accept netlink events from "unknown" (based on
ifindex) interfaces when a previously used card was removed earlier. If the
previously removed interface is added back, the driver_wext data need to be
updated to match with the new ifindex value. In addition, the initial setup
tasks for the card (set interface up, update ifindex, set mode, etc.) from
wpa_driver_wext_init() need to be run again.
This adds support for PS3 wireless to wpa_supplicant.
Although PS3 wireless driver is designed to conform the WEXT standard
as much as possible, unfortunately the wext driver wrapper of
wpa_supplicant can not support PS3 wireless fully because:
- PS3 wireless driver uses private WEXT ioctls for accepting PSK of
WPA-Personal from the userland.
WEXT does not specify the way to do it.
- The association and 4-way handshake are done by PS3 virtual
wireless device. The guest OSes can not interfere it.
- No EAPOL frames are allowed to go outside of the
hypervisor/firmware nor come from. They are eaten by the firmware.
Thus I needed to make a new driver wrapper for PS3 wireless.
This patch can be applied against the latest 0.6.x tree.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
