Move from this type of constructions:
switch (val) {
case 1:
something;
break;
}
default-action;
into following:
switch (val) {
case 1:
something;
break;
default:
default-action;
break
}
for cases where the switch statement is not expected to contain a full
set of enum values and as such, does not lose value from not having the
default target.
This makes the intent of default behavior clearer for static analyzers like
gcc with -Wswitch-default.
Signed-off-by: Chaoli Zhou <quic_zchaoli@quicinc.com>
Add new configuration options to configure EHT operating channel
width and center frequency.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
While these do not return error code within the current hostapd
implementation, matching functions in wpa_supplicant AP functionality
will have an error case and using consistent return type will make the
control interface code more consistent.
In addition, export hostapd_set_acl() in preparation for the
wpa_supplicant control interface implementation extension.
Signed-off-by: Chaoli Zhou <quic_zchaoli@quicinc.com>
There can be some discrepancy between the theorical dfs cac end (as
computed with the cac duration and cac start) and the actual cac end as
reported by the driver. During that window, the value of remaining time
outputed by the status command on the socket control interface will
display an overflowed, invalid value.
To mitigate this lets compute the remaining time as signed and display
it only when positive, otherwise defaulting it to 0.
Status command shows something like that when polling every seconds:
state=DFS
cac_time_seconds=60
cac_time_left_seconds=1
...
state=DFS
cac_time_seconds=60
cac_time_left_seconds=0
...
state=DFS
cac_time_seconds=60
cac_time_left_seconds=4294967294
...
state=DFS
cac_time_seconds=60
cac_time_left_seconds=4294967293
...
state=DFS
cac_time_seconds=60
cac_time_left_seconds=4294967292
...
state=ENABLED
cac_time_seconds=60
cac_time_left_seconds=N/A
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
For the function hostapd_get_sta_tx_rx(), the name
hostapd_get_sta_info() is more appropriate as it is also responsible for
getting many other STA specific params like RSSI, inactive milliseconds
along with TX and RX bytes.
Signed-off-by: Gokul Sivakumar <gokulkumar792@gmail.com>
When a Mesh interface is managed by wpa_supplicant, include the peer
link connected time (secs) in the output of "sta <addr>", "all_sta"
wpa_cli cmds for each peer. This will be helpful to find when the peer
link connection got established. The NL80211_STA_INFO_CONNECTED_TIME
netlink attribute data is used for this purpose if available.
$ wpa_cli -i mesh0 all_sta
02:00:00:00:02:00
flags=[ASSOC][WMM][HT]
aid=1
capability=0x0
listen_interval=0
supported_rates=82 84 8b 96 8c 12 98 24 b0 48 60 6c
timeout_next=NULLFUNC POLL
rx_packets=77
tx_packets=3
rx_bytes=8510
tx_bytes=284
inactive_msec=104
signal=-30
rx_rate_info=65 mcs 0
tx_rate_info=65 mcs 0
ht_mcs_bitmask=ffff0000000000000000
connected_time=24
ht_caps_info=0x103c
The connected_time field in the output of "hostapd_cli -i ap0 all_sta"
cmd is not affected and it will continue to show the connected time
maintained by hostapd for each STA.
Signed-off-by: Gokul Sivakumar <gokulkumar792@gmail.com>
Add HE as an accepted option ("he") in the CHAN_SWITCH command similarly
to the way VHT is addressed.
Signed-off-by: Muna Sinada <msinada@codeaurora.org>
Add the ability to disable HT/VHT/HE for specific BSS from hostapd.conf.
- Add disable_11ax boolean to hostapd_bss_config.
- Change disable_11n and disable_11ac to bool in hostapd_bss_config.
- Add configuration option to set these disable_11* parameters
(which were previously used only automatically based on incompatible
security parameters to disable HT/VHT).
Signed-off-by: Shay Bar <shay.bar@celeno.com>
Hardcoded CONFIG_IEEE80211N to be included to clean up implementation.
More or less all new devices support IEEE 802.11n (HT) and there is not
much need for being able to remove that functionality from the build.
Included this unconditionally to get rid of one more build options and
to keep things simpler.
Signed-off-by: Jouni Malinen <j@w1.fi>
Since send_mlme() now has support for the no_encrypt argument it is
possible to get rid of the remaining send_frame() uses.
Signed-off-by: Jouni Malinen <j@w1.fi>
Merge hostapd_drv_send_mlme_csa() functionality into
hostapd_drv_send_mlme() to get a single driver ops handler function for
hostapd. In addition, add a new no_encrypt parameter in preparation for
functionality that is needed to get rid of the separate send_frame()
driver op.
Signed-off-by: Jouni Malinen <j@w1.fi>
send_frame() is documented to be used for "testing use only" and as
such, it should not have used here for a normal production
functionality. Replace this with use of send_mlme() which is already
used for sending Deauthentication frames in other cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is mainly for testing purposes to be able to check which groups
a STA reports as having been rejected when using SAE H2E.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This adds a ieee80211ax=0/1 line to the STATUS output to indicate
the configuration of ieee80211ax, which similar to ieee80211n and
ieee80211ac.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
(&mgmt->u.deauth.reason_code + 1) is not exactly clean and now that we
have the u8 variable[] member in the struct after this field, use that
directly to avoid clang compiler warning:
ctrl_iface_ap.c:454:18: error: taking address of packed member
'reason_code' of class or structure 'ieee80211_mgmt::(anonymous
union)::(anonymous)' may result in an unaligned pointer value
[-Werror,-Waddress-of-packed-member]
Signed-off-by: Jouni Malinen <j@w1.fi>
It is now possible to optionally specify keyid for
each wpa_psk_file entry:
keyid=something 00:00:00:00:00:00 secretpassphrase
When station connects and the passphrase it used
has an associated keyid it will be appended to the
AP-STA-CONNECTED event string:
wlan0: AP-STA-CONNECTED 00:36:76:21:dc:7b keyid=something
It's also possible to retrieve it through the control interface:
$ hostapd_cli all_sta
Selected interface 'ap0'
00:36:76:21:dc:7b
...
keyid=something
New hostapd is able to read old wpa_psk_file. However, old hostapd will
not be able to read the new wpa_psk_file if it includes keyids.
Signed-off-by: Michal Kazior <michal@plume.com>
This allows user to get event indication when a new interface is
added/removed for 4addr WDS STA and also WDS STA ifname is informed
through the STA command.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
This allows external application to get last ACK signal strength of the
last transmitted frame if the driver makes this information
(NL80211_STA_INFO_ACK_SIGNAL) available.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
This allows external programs to get the average channel utilization.
The average channel utilization is calculated and reported through
STATUS command. Users need to configure chan_util_avg_period and
bss_load_update_period in hostapd config to get the average channel
utilization.
Signed-off-by: Bhagavathi Perumal S <bperumal@qti.qualcomm.com>
These allow external programs to determine supported legacy, HT, and VHT
rates of an interface or a STA.
Signed-off-by: Bhagavathi Perumal S <bperumal@qti.qualcomm.com>
This provides access to the Minimum/Maximum Transmit Power Capabilitie
fileds (the nominal minimum/maximum transmit power with which the STA
is capable of transmitting in the current channel; signed integer in
units of decibels relative to 1 mW).
Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
These allow external programs to fetch the TX and RX rate information
and signal strength for a specific STA through the hostapd control
interface command "STA <addr>". The values of these attributes are
filled in the response of nl80211 command NL80211_CMD_GET_STATION.
Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
This allows external programs to generate and add PMKSA cache entries
into hostapd. The main use for this is to run external DPP processing
(network introduction) and testing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These commnds are mesh version of PMKSA_GET/ADD commands. So the usage
and security risk is similar to them. Refer to
commit 3459381dd2 ('External persistent
storage for PMKSA cache entries') also.
The MESH_PMKSA_GET command requires peer MAC address or "any" as an
argument and outputs appropriate stored PMKSA cache. And the
MESH_PMKSA_ADD command receives an output of MESH_PMKSA_GET and re-store
the PMKSA cache into wpa_supplicant. By using re-stored PMKSA cache,
wpa_supplicant can skip commit message creation which can use
significant CPU resources.
The output of the MESH_PMKSA_GET command uses the following format:
<BSSID> <PMKID> <PMK> <expiration in seconds>
The example of MESH_PMKSA_ADD command is this.
MESH_PMKSA_ADD 02:00:00:00:03:00 231dc1c9fa2eed0354ea49e8ff2cc2dc cb0f6c9cab358a8146488566ca155421ab4f3ea4a6de2120050c149b797018fe 42930
MESH_PMKSA_ADD 02:00:00:00:04:00 d7e595916611640d3e4e8eac02909c3c eb414a33c74831275f25c2357b3c12e3d8bd2f2aab6cf781d6ade706be71321a 43180
This functionality is disabled by default and can be enabled with
CONFIG_PMKSA_CACHE_EXTERNAL=y build configuration option.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Implement the signature mechanism described in the paper
"Passive Taxonomy of Wifi Clients using MLME Frame Contents"
published by Denton Gentry and Avery Pennarun.
http://research.google.com/pubs/pub45429.htmlhttps://arxiv.org/abs/1608.01725
This involves:
1. Add a CONFIG_TAXONOMY compile option. Enabling taxonomy incurs
a memory overhead of up to several kilobytes per associated
station.
2. If enabled, store the Probe Request and (Re)Associate Request frame in
struct sta_info.
3. Implement code to extract the ID of each Information Element,
plus selected fields and bitmasks from certain IEs, into a
descriptive text string. This is done in a new source file,
src/ap/taxonomy.c.
4. Implement a "signature qq:rr:ss:tt:uu:vv" command
in hostapd_cli to retrieve the signature.
Signatures take the form of a text string. For example, a signature
for the Nexus 5X is:
wifi4|probe:0,1,127,45,191,htcap:01ef,htagg:03,htmcs:0000ffff,vhtcap:338061b2,
vhtrxmcs:030cfffa,vhttxmcs:030cfffa,extcap:00000a0201000040|assoc:0,1,48,45,
221(0050f2,2),191,127,htcap:01ef,htagg:03,htmcs:0000ffff,vhtcap:339071b2,
vhtrxmcs:030cfffa,vhttxmcs:030cfffa,extcap:0000000000000040
Signed-off-by: dgentry@google.com (Denton Gentry)
Signed-off-by: denny@geekhold.com (Denton Gentry)
Signed-off-by: rofrankel@google.com (Richard Frankel)
Signed-off-by: richard@frankel.tv (Richard Frankel)
Number of hostapd control interface commands (e.g., STATUS-DRIVER) could
result in NULL pointer dereference when issued on not yet enabled BSS.
Fix this by checking that the driver interface has been initialized
before calling the driver_ops function.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, HT/VHT state was shown in STATUS based on the configuration
parameter instead of the runtime operational parameters. This could
result in claiming HT/VHT to be enabled even when it was forced to be
disabled due to an incompatible configuration. Clear HT/VHT information
in the STATUS output if HT/VHT has been disabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The hostapd "POLL_STA <addr>" control interface command can be used to
check whether an associated station ACKs a QoS Data frame. The received
ACK for such a frame is reported as an event message ("AP-STA-POLL-OK
<addr>").
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The optional tx=0 parameter can be added to the hostapd
DEAUTHENTICATE/DISASSOCIATE command to request disconnection without
transmitting the Deauthentication/Disassociation frame to the STA.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows external programs to fetch the driver inactivity value for a
specific STA ("STA <addr>" hostapd control interface command).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the wpa_supplicant PMKSA_FLUSH control interface command to
allow the PMKSA list from the authenticator side to be flushed for AP
and mesh mode. In addition, this adds a hostapd PMKSA_FLUSH control
interface command to flush the PMKSA entries.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This extends the wpa_supplicant PMKSA control interface command to allow
the PMKSA list from the authenticator side to be listed for AP and mesh
mode. In addition, this adds a hostapd PMKSA control interface command
to show the same list for the AP case.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This makes hostapd track Supported Operating Classes information from
the associated STAs. The stored information is available through the STA
control interface command (supp_op_classes row) as a hexdump of the
Supported Operating Classes element starting from the Length field. This
information can be used as input to BSS transition management and
channel switching decisions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes hostapd parse the MBO attribute in (Re)Association Request
frame and track the cellular data capability (mbo_cell_capa=<val> in STA
control interface command).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the driver supports 64-bit TX/RX byte counters, use them directly.
The old 32-bit counter extension is maintained for backwards
compatibility with older drivers.
For nl80211 driver interface, the newer NL80211_STA_INFO_RX_BYTES64 and
NL80211_STA_INFO_TX_BYTES64 attributes are used when available. This
resolves the race vulnerable 32-bit value wrap/overflow. Rework RADIUS
accounting to use these for Acct-Input-Octets, Acct-Input-Gigawords,
Acct-Output-Octets, and Acct-Output-Gigawords, these values are often
used for billing purposes.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
