Like bgscan, autoscan is an optional module based feature to automate
scanning but while disconnected or inactive.
Instead of requesting directly a scan, it only sets the scan_interval
and the sched_scan_interval. So, if the driver supports sched_scan,
autoscan will be able to tweak its interval. Otherwise, the tweaked
scan_interval will be used. If scan parameters needs to be tweaked, an
autoscan_params pointer in wpa_s will provide those. So req_scan /
req_sched_scan will not set the scan parameters as they usually do, but
instead will use this pointer.
Modules will not have to request a scan directly, like bgscan does.
Instead, it will need to return the interval it wants after each
notification.
Signed-hostap: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Some drivers may independently decide to switch channels. Handle this by
updating the hostapd and wpa_supplicant AP and GO configuration.
Signed-hostap: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Some of the authentication/association failure paths left wpa_state to
its previous value. This can result in unexpected behavior when
wpa_supplicant tries to find an AP to connect to since the uncleared
state can result the in the selected BSS being ignored if it is same as
the previously used BSS. This could happen, e.g., when wpa_supplicant
SME was used and the AP rejected authentication. Fix this by explicitly
setting state to DISCONNECTED on auth/assoc failures that did not yet do
this.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
A p2p_find during provisioning shall not allow the enrollee to
pick the network, hence disable p2p_find during provisioning.
Signed-hostap: Sunil Dutt Undekari <duttus@codeaurora.org>
Previously, the STA entry was removed only from the driver and the STA
entry within hostapd was just marked disassociated. However, this left
the WPA authenticator state machine with an entry and the session was
not terminated properly. In addition, the STA entry could have remaining
indefinitely if the STA did not reconnect after TKIP countermeasures.
Fix this by removing the STA entry from hostapd instead of just leaving
it disassociated.
Signed-hostap: Jouni Malinen <j@w1.fi>
In AP which supports WPSv2 with only virtual push button, when PBC is
called, the WSC IE should include Selected Registrar Configuration
Methods attribute with the bit of the physical push button not set.
Signed-hostap: Yoni Divinsky <yoni.divinsky@ti.com>
Without this, we can get into a tight loop because the
code in general doesn't add eloop exception handlers,
so socket reporting the POLLERR would never be read.
With this change, any socket with POLLERR or POLLHUP
asserted will be handled by the read logic.
Signed-hostap: Ben Greear <greearb@candelatech.com>
The control message received from the kernel needs some space, but
there's no need for the strange typing that breaks clang compilation.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The wpas_p2p_pd_before_join_timeout could be left behind if the PD
Request in p2p_connect-auto case does not succeed. This timeout can
result in unexpected operations since it could trigger join operation
while going through GO Negotiation. Fix this by canceling the timeout
when falling back to GO Negotiation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Maintain a copy of Chargeable-User-Identity in the PMKSA cache to allow
it to be included in accounting messages even if full authentication was
not completed.
Signed-hostap: Jouni Malinen <j@w1.fi>
Calling-Station-Id, Acct-Session-Id, and User-Name attributes in a
Disconnect-Request message can now be used to indicate which station is
to be disconnected.
Signed-hostap: Jouni Malinen <j@w1.fi>
DAS will now validate Event-Timestamp value to be within an acceptable
time window (300 seconds by default; can be set using
radius_das_time_window parameter). In addition, Event-Timestamp can be
required in Disconnect-Request and CoA-Request messages with
radius_das_require_event_timestamp=1.
Signed-hostap: Jouni Malinen <j@w1.fi>
Currently, FullMAC Persistent GO can't use p2p_client_list because its
own hapd->p2p_group is NULL at ap_sta_set_authorized(). This patch
changes the processing to use sta->p2p_ie instead of
p2p_group_get_dev_addr() on FullMAC GO.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
The P2P Client Discoverability bit is reserved in most frames and its
value in the local P2P peer table should only be updated based on P2P
Group Info attribute from a GO. Fix this by avoiding changes to this
dev_capab bit based on other P2P frames. It would be more correct to
track this separately for each group in which the peer is a member, but
since we do not do that for the other group specific information either,
this can do for now.
It should be noted that prior to commit
18485b5469 wpa_supplicant set this bit in
all P2P frames. However, that commit changed this to match the
specification, i.e., the bit is not set in frames which are received
from P2P Device role. As such, this fix is needed to be able to figure
out that a peer supports client discoverability capability after that
commit.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
In the P2P specification v1.1, the P2P Client Discoverability bit is
described in Table 12 "Device Capability Bitmap definition". The table
says "Within a P2P Group Info attribute and a (Re)association request
frame the P2P Client Discoverability field shall be set to 1 when the
P2P Device supports P2P Client Discoverability, and is set to 0
otherwise. This field shall be reserved and set to 0 in all other frames
or uses.". To match with this, filter out P2P Client Discoverability bit
from frames where its use is reserved.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
If the peer uses an unknown reauth id, it would still be possible to use
pseudonym instead of permanent id. Allow this by changing the
AT_PERMANENT_ID_REQ to AT_FULLAUTH_ID_REQ in case unknown reauth id is
used in EAP-Response/Identity.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add an additional parameter to prioritize either sta or p2p connection
to resolve conflicts arising during single channel concurrency.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
This avoids issues with some APs rejecting a reassociation if the
station is not currently associated as reported by Yossi Wortzel.
The change is based on a patch from Arik Nemtsov.
Signed-hostap: Jouni Malinen <j@w1.fi>
There is a race condition in GO Negotiation Request frame sending and
processing that may end up with both devices sending GO Negotiation
Response. This response frame was previously accepted even if a response
had already been sent. This could result in two GO Negotiation Confirm
frames being exchanged and consequently, with two separate GO
Negotiations completing concurrently. These negotiations could result in
getting mismatching parameters (e.g., both device could believe it was
the GO).
Fix this by ignoring GO Negotiation Response from the peer if twe have
already sent a GO Negotiation Response frame and we have the higher P2P
Device Address. This is similar to the rule used to determine whether to
reply to GO Negotiation Request frame when Request was already sent,
i.e., the same direction of GO Negotiation is maintained here to enforce
that only the negotiation initiated by the device with smaller P2P
Device Address is completed.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
If both peers initiate GO Negotiation at about the same time, it is
possible for the GO Negotiation Request frame from the peer to be
received between the local attempt to send the GO Negotiation Request
and TX status event for that. This could result in both devices sending
GO Negotiation Response frames even though one of them should have
skipped this based which device uses a higher MAC address.
Resolve this race by incrementing go_neg_req_sent when p2p_send_action()
returns success instead of doing this from the TX status callback. If
the frame is not acknowledged, go_neg_req_sent is cleared in TX status
handler.
Signed-off-by: Neeraj Garg <neerajkg@broadcom.com>
Stop the connection attempt if GO Negotiation Confirm is not received
within 100 ms of the GO Negotiation Response getting acknowledged.
Previously, we would have continued trying to connect to the peer even
in this case which could result in confusing second GO Negotiation
Request frame and unnecessarily long wait before indicating failure.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 361cdf3400 changed the way the
group formation timeout is used on P2P client. However, it resulted in
clearing the timeout on the GO when the GO started beaconing. This is
not correct since the timeout is supposed to be maintained until at
least the completion of the WPS provisioning step. Fix this regression
by clearing the timeout here only in the case we are not GO in group
formation phase.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for wpa_state to be WPA_DISCONNECTED when a new scan is
scheduled to be started in the future. If wpas_wps_cancel() gets called
(e.g., through control interface wps_cancel or a P2P group removal)
while in that state, the WPS operation (scan request and special network
block) were not removed. Fix this by clearing the WPS operations both in
WPA_SCANNING and WPA_DISCONNECTED states.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
The previous version set scan_res_handler unconditionally and then
cleared it if scan request failed. This can result in incorrect clearing
of the handler to NULL for a previously started scan that has not yet
completed. This can make p2p_find command fail to use the
start-after-scan-completion mechanism in some cases. Fix this by setting
scan_res_handler properly after having verified that the driver command
for starting the scan was successful.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
The GO Negotiation Confirm frame doesn't need to be sent with a wait
since we don't expect a response to it.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Perform addition additional scan runs on the operating channel of the GO
(if known from previous scan results) and fall back to initiate the PD
for GO Negotiation if these additional scans do not detect the peer as
GO.
Signed-hostap: Sunil Dutt Undekari <duttus@codeaurora.org>
Concurrent Operation bit was not set for GO even if the device
supports concurrent operations. Make sure the Device Capability
value is consistent with other P2P use cases by using the value
determined in p2p_init().
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
Commit 361cdf3400 extended the use of
group formation timeout for the way handshake, but the registration was
done on the group_interface while the cancellation was done on the
parent interface. Fix the registration to set the eloop timeout on
parent to address potential issues when using a separate group
interface.
Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
When looking for a BSS to eject due to too many entries, never
pick one that is in use. Otherwise, we run the risk of having
pointers to freed data.
Signed-hostap: Paul Stewart <pstew@chromium.org>
Send an "EAP" signal via the new DBus interface under various
conditions during EAP authentication:
- During method selection (ACK and NAK)
- During certificate verification
- While sending and receiving TLS alert messages
- EAP success and failure messages
This provides DBus callers a number of new tools:
- The ability to probe an AP for available EAP methods
(given an identity).
- The ability to identify why the remote certificate was
not verified.
- The ability to identify why the remote peer refused
a TLS connection.
Signed-hostap: Paul Stewart <pstew@chromium.org>
In certain cases like PBC session overlap it appears to be possible that
an interface is removed due to an event handled on it, this leads to
list corruption. Use safe iteration to prevent this issue.
Reported-by: Nirav Shah <nirav.j2.shah@intel.com>
Reported-by: Neeraj Kumar Garg <neerajkg@broadcom.com>
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
intended-for: hostap-1
