Add ANQP fields to the BSS properties to allow DBus clients to be
notified and obtain the values when it changes.
Signed-off-by: Damien Dejean <damiendejean@chromium.org>
Add a D-Bus method to perform ANQP get requests. The new method is
equivalent to the "anqp_get" command available in wpa_cli.
Signed-off-by: Damien Dejean <damiendejean@chromium.org>
To implement an action script that listens for DPP push button events
and for example blinks a LED it is useful to know when push button has
started. Emit an event when push button starts.
Signed-off-by: Evan Benn <evan.benn@morsemicro.com>
This wait for a specific event is needed to allow a new DPP-PB-STATUS
event to be added at the start of the PB operation.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Verify that CSA can be performed on the first link of an AP MLD and
further check that traffic still continues even after channel switch.
Finally, check again that a subsequent CSA can be performed without
affecting the data traffic.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
When puncturing is used on EHT, the HT/VHT/HE channel configuration must
not encompass the punctured subchannel, so must use a lower bandwidth.
Change the puncturing tests accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit eecaceed8f. This test
case can now be restored since hostapd is modified to allow test cases
changes to be done to cover the special impact from EHT puncturing to
available HT/VHT/HE channel bandwidth in this particular case.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is needed to allow some cases where puncturing prevents HT/VHT/HE
from using the full channel bandwidth.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is needed to be able to check validity of the channel parameters
for cases where EHT puncturing impacts what can be enabled for
HT/VHT/HE.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
mac80211 has been modified to reject the configuration that is used in
this test case. For now, remove this until the puncturing of the second
20 MHz segment can be handled in a manner that allows mac80211 STA to
use EHT.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The testing functionality for overriding EHT puncturing bitmap was
applied only for the EHT elements. The mac80211 has been updated to
enforce compartibility between EHT and HT/VHT information and that made
the related test cases fail. Apply the override value for VHT element
generation to avoid some of those issues.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Leave the HT capability of the AP as-is when running channel switch test
cases that started failing with a recent kernel change that disconnects
on such "unexpected" change in AP capabilities.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Processing of WNM frames can results in a lookup of the current BSS
table. As such, the testing tool needs to initialize the BSS table to
avoid NULL pointer dereferences. This is not an issue that would show up
with real production uses with wpa_supplicant since wpa_bss_init() is
called there.
Credit to OSS-Fuzz: https://bugs.chromium.org/p/oss-fuzz/issues/detail?id=67244
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The commit that renamed the WNM BTM deallocation function forgot to
update the fuzz tester tool.
Fixes: e508c070c4 ("WNM: Keep BTM information until connection completes")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The wpa_supplicant implementation for building the Supported Operating
Classes element was modified to add support for 80 MHz and wider
bandwidth on the 6 GHz band, 2-octet operating classes, and freq_list on
the 6 GHz band. Update the test cases that verify exact encoding of this
information to match the implementation changes.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Only the 2.4 and 5 GHz channels were handled previously when removing
operating classes from the Supported Operating Classes element based on
the freq_list parameter. Extend this to include the 6 GHz band as well.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
A previous workaround was used to move the special operating class 130
to the end of the Supported Operating Classes element to avoid getting
any following entry being ignored or misunderstood. That is not really
the correct way of encoding the special cases, i.e., 80+80 MHz channels
that use two nonadjacent frequency segments.
Add support for encoding the 80+80 MHz channel with the 2-octet
operating class design using the Operating Class Duple sequence field of
the Supported Operating Classes element instead of listing the operating
classes that have the 80+ behavior limit set indication in Table E-4
(i.e., opclass 130 and 135) as 1-octet operating classes in the
Operating Classes field.
Fixes: a92660a00e ("Work around Supported Operating Classes element issues for 6 GHz")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Commit 085a3fc76e ("EHT: Add 320 channel width support") added this in
various places, but it did not cover everything. Extend this support to
be more complete. In particular, this allows wpa_supplicant to report
the operating class 137 in the Supported Operating Classes element and
to use it when processing beacon requests.
Signed-off-by: Ainy Kumari <quic_ainykuma@quicinc.com>
short_ssid in the own neighbor report might get out of sync, causing
advertising RNR element based on the old SSID, when SSID is changed
either with control interface command SET or with SIGHUP. Therefore,
sync the own report entry by removing the old entry and setting own
report again if the short SSID value has changed.
Signed-off-by: Nikita Chernikov <nchernikov@maxlinear.com>
Once the non-AP MLD is added to the driver, the driver handles the
address translation so that hostapd receives Management frames with
SA/DA being translated into MLD MAC addresses.
If the Authentication frmae is retransmitted with transaction being 1,
SA of the retransmitted Authentication frame is translated into the MLD
MAC address by the driver, and then in the function handle_auth(),
sta->mld_info.links[].peer_addr would be replaced by the MLD MAC address
even though it is supposed to be the link address.
Therefore, update the MLD information only when the STA has not yet been
added into the driver to avoid replacing the previously determined link
address with the MLD MAC address.
Fixes: bcbe80a66 ("AP: MLO: Handle Multi-Link element during authentication")
Signed-off-by: Michael-CY Lee <michael-cy.lee@mediatek.com>
reply_size instead sizeof(buffer) should be provided to
hostapd_global_ctrl_iface_interfaces() when processing INTERFACES
commands. The previous use of sizeof(buffer) used a significantly
shorter limit (256 vs. 4096 bytes) for the output and this could have
resulted in unnecessary truncation of the output.
Fixes: 618f5d01b0 ("hostapd: Add INTERFACES ctrl_iface command")
Signed-Off-By : Mujibur Rahiman K mujiburrahimank@maxlinear.com
In theory, os_snprintf() could return a negative value and as such,
os_snprintf_error() should be used in all cases where the buffer might
not be large enough.
Signed-off-by: Jouni Malinen <j@w1.fi>
The INT_RANGE() cases for wpa_supplicant global and network profile
parameters ended up changing the configured value to the minimum value
if the provided value was too small or to the maximum value if the
provided value was too large. This does not seem most logical. Change
this to not change the configured value at all if the provided value is
outside the valid range.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like this test case can fail in some cases. Add more debug info
and event wait that might help with a race condition.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like the 30 second timeout, i.e., 25 second to discover and
receive GO Negotiation Request, was not sufficient for all cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
These parameters have both a separate SET command handler and a global
configuration parameter handler. Only the global configuration parameter
handler for enforcing valid range checking. Do that for the SET command
as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
The following config file contains invalid items:
----
filter_rssi=1234 # should be rejected
network={
mode=-1 # should be rejected
ssid="ssid"
psk="password"
}
----
But it is accepted by the config parser. The issue is due to using NULL
to represent no limit. If a boundary is set to 0, it's disregarded.
Fix this.
Note that string parser is not affected as length cannot be negative and
we are not limiting any string to be always empty.
Signed-off-by: Chien Wong <m@xv97.com>
Use of wpa_s->p2p_go_no_pri_sec_switch needs to be conditional on
CONFIG_P2P being defined for the build to avoid a compilation error and
ssid->p2p_group to avoid using this for non-P2P AP mode case in
wpa_supplicant. Furthermore, it is better to clear this flag when
stopping a P2P GO to reduce risk of this getting used for a separate
instance of starting a GO.
Fixes: b18d957593 ("P2P: Disable pri/sec channel switch for GO with forced frequency")
Signed-off-by: Jouni Malinen <j@w1.fi>
In the MLD case, the information from the transition management request
is relevant during the association process in order to filter out links
that were disallowed by the BTM request. Also, the information remains
useful should a connection attempt fail.
To enable these scenarios, keep the information around until the
connection has completed. As this might make it impossible to establish
a connection, also clear this information at the same time that a normal
BSS ignore is cleared to avoid getting stuck in case the transition
fails unexpectedly.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
If the last link is dropped, it makes sense to follow the BTM procedure.
However, in that case we need to prevent reconnection to this link
specifically, while if the AP MLD is terminating we need to forbid
connecting to the AP MLD.
As such, add a new variable to track the BSSID or AP MLD MAC address.
Which one it refers to depends on whether wnm_link_removal is set.
This also simplifies the check in wnm_is_bss_excluded() and untangles it
from wpa_s->current_bss.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
All callers of wnm_send_bss_transition_mgmt_resp() are explicitly
passing wpa_s->wnm_dialog_token. As such, we might as well not pass it
and use the variable directly.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
There is no point in the caller to set it to zero. Just do so within
wnm_send_bss_transition_mgmt_resp().
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
The elements are (currently) not used except for sending an immediate
response similar to COLOC_INTF_REPORT with the main difference being
that the dialog token is included.
Do not store the elements. It easy enough to re-add this should the
implementation improve. And this fixes the fact that the variable is
cleared at odd times as wnm_deallocate_memory() is used specifically to
clear the neighbor report list of a BTM request.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
There is no need for this check as wpa_scan_res_match() already calls
the function through wpa_scan_res_ok() before accepting a match.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
The call to wpa_scan_res_match already checks that the SSID matches
current_ssid. Therefore there is no need to do any further checking.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
