A number of persistent settings of Nix are stored in the file sysconfdir/nix/nix.conf. This file is a list of name = value pairs, one per line. Comments start with a # character. An example configuration file is shown in . gc-keep-outputs = true # Nice for developers gc-keep-derivations = true # Idem env-keep-derivations = false The following variables are currently available: gc-keep-outputs If true, the garbage collector will keep the outputs of non-garbage derivations. If false (default), outputs will be deleted unless they are GC roots themselves (or reachable from other roots). In general, outputs must be registered as roots separately. However, even if the output of a derivation is registered as a root, the collector will still delete store paths that are used only at build time (e.g., the C compiler, or source tarballs downloaded from the network). To prevent it from doing so, set this option to true. gc-keep-derivations If true (default), the garbage collector will keep the derivations from which non-garbage store paths were built. If false, they will be deleted unless explicitly registered as a root (or reachable from other roots). Keeping derivation around is useful for querying and traceability (e.g., it allows you to ask with what dependencies or options a store path was built), so by default this option is on. Turn it off to safe a bit of disk space (or a lot if gc-keep-outputs is also turned on). env-keep-derivations If false (default), derivations are not stored in Nix user environments. That is, the derivation any build-time-only dependencies may be garbage-collected. If true, when you add a Nix derivation to a user environment, the path of the derivation is stored in the user environment. Thus, the derivation will not be garbage-collected until the user environment generation is deleted (nix-env --delete-generations). To prevent build-time-only dependencies from being collected, you should also turn on gc-keep-outputs. The difference between this option and gc-keep-derivations is that this one is “sticky”: it applies to any user environment created while this option was enabled, while gc-keep-derivations only applies at the moment the garbage collector is run. build-max-jobs This option defines the maximum number of jobs that Nix will try to build in parallel. The default is 1. You should generally set it to the number of CPUs in your system (e.g., 2 on a Athlon 64 X2). It can be overriden using the --max-jobs (-j) command line switch. build-cores Sets the value of the NIX_BUILD_CORES environment variable in the invocation of builders. Builders can use this variable at their discretion to control the maximum amount of parallelism. For instance, in Nixpkgs, if the derivation attribute enableParallelBuilding is set to true, the builder passes the -jN flag to GNU Make. It can be overriden using the --cores command line switch and defaults to 1. The value 0 means that the builder should use all available CPU cores in the system. build-max-silent-time This option defines the maximum number of seconds that a builder can go without producing any data on standard output or standard error. This is useful (for instance in a automated build system) to catch builds that are stuck in an infinite loop, or to catch remote builds that are hanging due to network problems. It can be overriden using the --max-silent-time command line switch. The value 0 means that there is no timeout. This is also the default. build-timeout This option defines the maximum number of seconds that a builder can run. This is useful (for instance in a automated build system) to catch builds that are stuck in an infinite loop but keep writing to their standard output or standard error. It can be overriden using the --timeout command line switch. The value 0 means that there is no timeout. This is also the default. build-users-group This options specifies the Unix group containing the Nix build user accounts. In multi-user Nix installations, builds should not be performed by the Nix account since that would allow users to arbitrarily modify the Nix store and database by supplying specially crafted builders; and they cannot be performed by the calling user since that would allow him/her to influence the build result. Therefore, if this option is non-empty and specifies a valid group, builds will be performed under the user accounts that are a member of the group specified here (as listed in /etc/group). Those user accounts should not be used for any other purpose! Nix will never run two builds under the same user account at the same time. This is to prevent an obvious security hole: a malicious user writing a Nix expression that modifies the build result of a legitimate Nix expression being built by another user. Therefore it is good to have as many Nix build user accounts as you can spare. (Remember: uids are cheap.) The build users should have permission to create files in the Nix store, but not delete them. Therefore, /nix/store should be owned by the Nix account, its group should be the group specified here, and its mode should be 1775. If the build users group is empty, builds will be performed under the uid of the Nix process (that is, the uid of the caller if NIX_REMOTE is empty, the uid under which the Nix daemon runs if NIX_REMOTE is daemon, or the uid that owns the setuid nix-worker program if NIX_REMOTE is slave). Obviously, this should not be used in multi-user settings with untrusted users. build-use-chroot If set to true, builds will be performed in a chroot environment, i.e., the build will be isolated from the normal file system hierarchy and will only see the Nix store, the temporary build directory, and the directories configured with the build-chroot-dirs option (such as /proc and /dev). This is useful to prevent undeclared dependencies on files in directories such as /usr/bin. The use of a chroot requires that Nix is run as root (but you can still use the “build users” feature to perform builds under different users than root). Currently, chroot builds only work on Linux because Nix uses “bind mounts” to make the Nix store and other directories available inside the chroot. build-use-substitutes If set to true (default), Nix will use binary substitutes if available. This option can be disabled to force building from source. build-chroot-dirs When builds are performed in a chroot environment, Nix will mount (using mount --bind on Linux) some directories from the normal file system hierarchy inside the chroot. These are the Nix store, the temporary build directory (usually /tmp/nix-pid-number) and the directories listed here. The default is dev /proc. Files in /dev (such as /dev/null) are needed by many builds, and some files in /proc may also be needed occasionally. The value used on NixOS is build-use-chroot = /dev /proc /bin to make the /bin/sh symlink available (which is still needed by many builders). build-cache-failures If set to true, Nix will “cache” build failures, meaning that it will remember (in its database) that a derivation previously failed. If you then try to build the derivation again, Nix will immediately fail rather than perform the build again. Failures in fixed-output derivations (such as fetchurl calls) are never cached. The “failed” status of a derivation can be cleared using nix-store --clear-failed-paths. By default, failure caching is disabled. system This option specifies the canonical Nix system name of the current installation, such as i686-linux or powerpc-darwin. Nix can only build derivations whose system attribute equals the value specified here. In general, it never makes sense to modify this value from its default, since you can use it to ‘lie’ about the platform you are building on (e.g., perform a Mac OS build on a Linux machine; the result would obviously be wrong). It only makes sense if the Nix binaries can run on multiple platforms, e.g., ‘universal binaries’ that run on powerpc-darwin and i686-darwin. It defaults to the canonical Nix system name detected by configure at build time. fsync-metadata If set to true, changes to the Nix store metadata (in /nix/var/nix/db) are synchronously flushed to disk. This improves robustness in case of system crashes, but reduces performance. The default is true.