209 lines
6.9 KiB
Nix
209 lines
6.9 KiB
Nix
|
|
# I like GL.iNet devices because they're relatively accessible to
|
|
# DIY users: the serial port connections have headers preinstalled
|
|
# and don't need soldering
|
|
|
|
# Mainline linux 5.19 doesn't have device-tree support for this device
|
|
# or even for the SoC, so we use the extensive OpenWrt kernel patches
|
|
|
|
{
|
|
system = {
|
|
crossSystem = {
|
|
config = "mips-unknown-linux-musl";
|
|
gcc = {
|
|
abi = "32";
|
|
arch = "mips32"; # maybe mips_24kc-
|
|
};
|
|
};
|
|
};
|
|
|
|
description = ''
|
|
GL.INet GL-AR750 "Creta" travel router
|
|
- QCA9531 @650Mhz SoC
|
|
- dual band wireless: IEEE 802.11a/b/g/n/ac
|
|
- two 10/100Mbps LAN ports and one WAN
|
|
- 128MB DDR2 RAM / 16MB NOR Flash
|
|
- "ath79" soc family
|
|
https://www.gl-inet.com/products/gl-ar750/
|
|
|
|
The GL-AR750 has two distinct sets of wifi hardware. The 2.4GHz
|
|
radio is part of the QCA9531 SoC, i.e. it's on the same silicon as
|
|
the CPU, the Ethernet, the USB etc. The device is connected to the
|
|
host via AHB, the "Advanced High-Performance Bus" and it is
|
|
supported in Linux using the ath9k driver. The 5GHz support, on the
|
|
other hand, is provided by a QCA9887 PCIe (PCI embedded) WLAN chip:
|
|
I haven't looked closely at the router innards to see if this is
|
|
actually physically a separate board that could be unplugged, but
|
|
as far as the Linux is concerned it behaves as one. This is
|
|
supported by the ath10k driver.
|
|
'';
|
|
|
|
module = {pkgs, config, ... }:
|
|
let
|
|
openwrt = pkgs.openwrt;
|
|
firmwareBlobs = pkgs.pkgsBuildBuild.fetchFromGitHub {
|
|
owner = "kvalo";
|
|
repo = "ath10k-firmware";
|
|
rev = "5d63529ffc6e24974bc7c45b28fd1c34573126eb";
|
|
sha256 = "1bwpifrwl5mvsmbmc81k8l22hmkwk05v7xs8dxag7fgv2kd6lv2r";
|
|
};
|
|
firmware = pkgs.stdenv.mkDerivation {
|
|
name = "wlan-firmware";
|
|
phases = ["installPhase"];
|
|
installPhase = ''
|
|
mkdir -p $out/ath10k/QCA9887/hw1.0/
|
|
blobdir=${firmwareBlobs}/QCA9887/hw1.0
|
|
cp $blobdir/10.2.4-1.0/firmware-5.bin_10.2.4-1.0-00047 $out/ath10k/QCA9887/hw1.0/firmware-5.bin
|
|
cp $blobdir/board.bin $out/ath10k/QCA9887/hw1.0/
|
|
'';
|
|
};
|
|
mac80211 = pkgs.mac80211.override {
|
|
drivers = ["ath9k" "ath10k_pci"];
|
|
klibBuild = config.outputs.kernel.modulesupport;
|
|
};
|
|
ath10k_cal_data =
|
|
let
|
|
offset = 1024 * 20; # 0x5000
|
|
size = 2048 + 68; # 0x844
|
|
in pkgs.liminix.services.oneshot rec {
|
|
name = "ath10k_cal_data";
|
|
up = ''
|
|
part=$(basename $(dirname $(grep -l art /sys/class/mtd/*/name)))
|
|
echo ART partition is ''${part-unset}
|
|
test -n "$part" || exit 1
|
|
(in_outputs ${name}
|
|
dd if=/dev/$part of=data iflag=skip_bytes,fullblock bs=${toString size} skip=${toString offset} count=1
|
|
)
|
|
'';
|
|
down = "true";
|
|
};
|
|
inherit (pkgs.pseudofile) dir symlink;
|
|
inherit (pkgs.liminix.networking) interface;
|
|
in {
|
|
hardware = {
|
|
defaultOutput = "tftpboot";
|
|
loadAddress = "0x80060000";
|
|
entryPoint = "0x80060000";
|
|
flash = {
|
|
address = "0x9F060000";
|
|
size ="0xfa0000";
|
|
};
|
|
rootDevice = "1f05";
|
|
dts = {
|
|
src = "${openwrt.src}/target/linux/ath79/dts/qca9531_glinet_gl-ar750.dts";
|
|
includes = [
|
|
"${openwrt.src}/target/linux/ath79/dts"
|
|
];
|
|
};
|
|
|
|
networkInterfaces = {
|
|
lan = interface { device = "eth0"; };
|
|
wan = interface { device = "eth1"; };
|
|
|
|
wlan_24 = interface {
|
|
device = "wlan0";
|
|
dependencies = [ mac80211 ];
|
|
};
|
|
wlan_5 = interface {
|
|
device = "wlan1";
|
|
dependencies = [ mac80211 ath10k_cal_data ];
|
|
};
|
|
};
|
|
};
|
|
filesystem = dir {
|
|
lib = dir {
|
|
firmware = dir {
|
|
ath10k = dir {
|
|
QCA9887 = symlink "${firmware}/ath10k/QCA9887";
|
|
"cal-pci-0000:00:00.0.bin" = symlink "${ath10k_cal_data}/.outputs/data";
|
|
};
|
|
};
|
|
};
|
|
};
|
|
boot.tftp = {
|
|
loadAddress = "0x00A00000";
|
|
};
|
|
kernel = {
|
|
src = pkgs.pkgsBuildBuild.fetchurl {
|
|
name = "linux.tar.gz";
|
|
url = "https://cdn.kernel.org/pub/linux/kernel/v5.x/linux-5.15.71.tar.gz";
|
|
hash = "sha256-yhO2cXIeIgUxkSZf/4aAsF11uxyh+UUZu6D1h92vCD8=";
|
|
};
|
|
extraPatchPhase = ''
|
|
${openwrt.applyPatches.ath79}
|
|
'';
|
|
config = {
|
|
MIPS_ELF_APPENDED_DTB = "y";
|
|
OF = "y";
|
|
USE_OF = "y";
|
|
ATH79 = "y";
|
|
PCI = "y";
|
|
PCI_AR724X = "y";
|
|
|
|
SERIAL_8250_CONSOLE = "y";
|
|
SERIAL_8250 = "y";
|
|
SERIAL_CORE_CONSOLE = "y";
|
|
|
|
# need this to open console device at boot. dmesg goes from
|
|
# [ 0.272934] Warning: unable to open an initial console.
|
|
# to
|
|
# [ 0.247413] printk: console [ttyS0] disabled
|
|
# [ 0.25200] 18020000.uart: ttyS0 at MMIO 0x1802000 (irq = 10, base_baud = 1562500) is a 16550A
|
|
SERIAL_OF_PLATFORM = "y";
|
|
|
|
CONSOLE_LOGLEVEL_DEFAULT = "8";
|
|
CONSOLE_LOGLEVEL_QUIET = "4";
|
|
|
|
# "empty" initramfs source should create an initial
|
|
# filesystem that has a /dev/console node and not much
|
|
# else. Note that pid 1 is started *before* the root
|
|
# filesystem is mounted and it expects /dev/console to
|
|
# be present already
|
|
BLK_DEV_INITRD = "n";
|
|
|
|
NET = "y";
|
|
NETDEVICES = "y";
|
|
ETHERNET = "y";
|
|
NET_VENDOR_ATHEROS = "y";
|
|
AG71XX = "y"; # ethernet (qca,qca9530-eth)
|
|
MFD_SYSCON = "y"; # ethernet (compatible "syscon")
|
|
AR8216_PHY = "y"; # eth1 is behind a switch
|
|
|
|
MTD_SPI_NOR = "y";
|
|
SPI_ATH79 = "y"; # these are copied from OpenWrt.
|
|
SPI_MASTER= "y"; # At least one of them is necessary
|
|
SPI_MEM= "y";
|
|
SPI_AR934X= "y";
|
|
SPI_BITBANG= "y";
|
|
SPI_GPIO= "y";
|
|
GPIO_ATH79 = "y";
|
|
GPIOLIB = "y";
|
|
EXPERT="y";
|
|
GPIO_SYSFS = "y"; # required by patches-5.15/0004-phy-add-ath79-usb-phys.patch
|
|
OF_GPIO = "y";
|
|
SYSFS = "y";
|
|
SPI = "y";
|
|
MTD = "y";
|
|
MTD_CMDLINE_PARTS = "y";
|
|
MTD_BLOCK = "y"; # fix undefined ref to register_mtd_blktrans_devs
|
|
|
|
WATCHDOG = "y";
|
|
ATH79_WDT = "y"; # watchdog timer
|
|
|
|
CPU_BIG_ENDIAN= "y";
|
|
|
|
# this is all copied from nixwrt ath79 config. Clearly not all
|
|
# of it is device config, some of it is wifi config or
|
|
# installation method config or ...
|
|
|
|
CMDLINE_PARTITION = "y";
|
|
EARLY_PRINTK = "y";
|
|
|
|
PARTITION_ADVANCED = "y";
|
|
PRINTK_TIME = "y";
|
|
SQUASHFS = "y";
|
|
SQUASHFS_XZ = "y";
|
|
};
|
|
};
|
|
};
|
|
}
|