When "P2P_SET nfc_tag 1" is used to enable the own NFC Tag for P2P, also
enable it for any running GO interface.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"NFC_REPORT_HANDOVER {INIT,RESP} P2P <req> <sel>" can now be used to
report completed NFC negotiated connection handover in which the P2P
alternative carrier was selected.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new Device Password ID 7 is used to indicate that NFC connection
handover is used with DH public key hash from both devices being
exchanged over the NFC connection handover messages. This allows an
abbreviated M1-M2 handshake to be used since Device Password does not
need to be used when DH is authenticated with the out-of-band
information (validation of the public key against the hash).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When both the Registrar and Enrollee public key hashes are delivered
out-of-band (in NFC connection handover), use abbreviated WPS handshake
(skip M3-M8).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Instead of terminating the WPS protocol immediately, go through an M2D
exchange to notify Enrollee of the public key hash mismatch.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The PBC ignore-start workaround just needs to check whether
the time is within 5 seconds, so should use monotonic time.
While at it, add a few more ifdefs to clearly separate the
code and variables needed.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
PBC sessions are just time-stamped when activated, and
eventually time out, so should use monotonic time.
While at it, make the code use os_reltime_expired().
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This makes the P2P Device Address of the Enrollee available with the PSK
records to allow P2P Device Address instead of P2P Interface Address to
be used for finding the correct PSK.
Signed-hostap: Jouni Malinen <j@w1.fi>
"wpa_cli p2p_set per_sta_psk <0/1>" can now be used to disable/enable
use of per-device PSKs in P2P groups. This is disabled by default.
When enabled, a default passphrase is still generated by the GO for
legacy stations, but all P2P and non-P2P devices using WPS will get
a unique PSK.
This gives more protection for the P2P group by preventing clients from
being able to derive the unicast keys used by other clients. This is
also a step towards allowing specific clients to be removed from a group
reliably without having to tear down the full group to do so.
Signed-hostap: Jouni Malinen <j@w1.fi>
According to WSC specification (Ver 2.0.2, section 8.3), RF Bands
attribute should be set to the specific RF band used for the current
message. Add an option to set wanted band in wps_build_rf_bands() and
add a callback to get the current band from wpa_supplicant and hostapd.
Signed-hostap: David Spinadel <david.spinadel@intel.com>
When a specific out-of-band Device Password is enabled, it can be useful
to be able to advertise that in the selected registrar information.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
WSC specification 2.0 section 7.4 describes OOB password to be expressed
in ASCII format (upper case hexdump) instead of raw binary.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Registrar is allowed to propose another Device Password ID in M2. Make
Enrollee validate Device Password ID in M2 to check if this happened.
This commit adds support for changing from NFC password token to default
PIN for the case where the AP is the Enrollee and has both the NFC
password token and AP PIN enabled at the same time.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
WSC IE in Beacon and Probe Response frames should behave consistently
as far as the RF Bands attribute is concerned. Use the same dualband
condition for adding this into Probe Response frames since the value
is not really needed if the AP is not a dualband AP.
Signed-hostap: Jouni Malinen <j@w1.fi>
Some deployed station implementations implement WPS incorrectly and
end up causing PBC session overlap issues by indicating active PBC
mode in a scan after the WPS provisioning step. Work around this by
ignoring active PBC indication in a Probe Request from a station that
completed PBC provisioning during the last five seconds.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The UFD (USB flash drive) configuration method was deprecated in WSC
2.0. Since this is not known to be used, remove the UFD implementation
from hostapd and wpa_supplicant to allow the WPS implementation to be
cleaned up. This removes the now unused OOB operations and ctrl_iface
commands that had already been deprecated by the new NFC operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, WPS Registrar allowed multiple wildcard PINs to be
configured. This can get confusing since these PINs get assigned to any
Enrollee that does not have a specific PIN and as such, cannot really be
used with different PIN values in reasonable ways. To avoid confusion
with multiple enabled PINs, invalidate any previously configured
wildcard PIN whenever adding a new one.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Multiple memcmps of nonces were actually comparing only the first byte
instead of all 16 bytes. [Bug 462]
Signed-hostap: Eyal Shapira <eyal@wizery.com>
intended-for: hostap-1
This adds a cleaner mechanism for handling NFC Password Tokens in the
WPS Registrar. There could be more than one active NFC Password Token in
use and as such, a list of tokens needs to be maintained. The old
WPS_OOB interface is still using the old mechanism that supports only a
single active NFC Password Token.
Signed-hostap: Jouni Malinen <j@w1.fi>
hostapd ctrl_iface can now be used to deliver payload from read
operation of an NFC tag. This allows operations without having to have
low-level NFC code within hostapd. For now, the new wps_nfc_tag_read
command can be used with NFC password tokens for the case where the AP
has an NFC device that is used to read an NFC tag from the station
Enrollee.
Signed-hostap: Jouni Malinen <j@w1.fi>
In AP which supports WPSv2 with only virtual push button, when PBC is
called, the WSC IE should include Selected Registrar Configuration
Methods attribute with the bit of the physical push button not set.
Signed-hostap: Yoni Divinsky <yoni.divinsky@ti.com>
If a wildcard PIN is used on any of the radios that hostapd is
controlling, invalidate the matching PIN on all the other radios
to avoid multiple uses of the same PIN.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, PINs that are added with a wildcard UUID were allowed to
be used only by a single Enrollee. However, there may be more than one
Enrollee trying to connect when an AP indicates that active Registrar
is present. As a minimal workaround, allow two Enrollees to try to use
the wildcard PIN. More complete extension could use timeout and allow
larger set of Enrollees to try to connect (while still keeping in mind
PIN disabling requirement after 10 failed attempts).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Since wps_registrar_pbc_timeout is called to stop PBC, previously
registered wps_registrar_pbc_timeout must be canceled when canceling
the WPS operation.
Signed-off-by: Spencer Chang <jungwalk@gmail.com>
WPS overlap detection can detect false overlap if a P2P peer
changes UUID while authentication is ongoing. Changing UUID
is of course wrong but this is what some popular devices do
so we need to work around it in order to keep compatibility
with these devices. There already is a mechanism in WPS
registrar to skip overlap detection if P2P addresses of two
sessions match but it wasn't really triggered because the
address wasn't filled in in the caller function.
Let's fill in this address and also clean up WPS PBC sessions
on WSC process completion if UUID was changed.
Signed-hostap: Vitaly Wool<vitalywool@gmail.com>
When hostapd controls multiple radios, WPS operations are started on
all interfaces. However, when the provisioning run had been completed
successfully, actiove WPS mode was stopped only a single interface. Fix
this to iterate through all interfaces so that this is handled
consistently with the starting of WPS operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 628d54639a introduced number
of new WPS related ctrl_iface messages to hostapd. Some of these
were for ER events which do not make any sense to hostapd that
cannot operate as an ER. The WPS_EV_ER_SET_SELECTED_REGISTRAR one
from wps_registrar_sel_registrar_changed_event() was especially
problematic since it can cause wpa_supplicant ER code segfault due
to missing event data.
Revert all the ER specific changes from commit
628d54639a to get rid of the segfault
and undesired extra code in hostapd.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When the supplicant acts as a registrar to learn the access point
parameters send the credentials to the wpa_cli interface after
receiving the 7th message. This is needed for proper behavior with
wps_cred_processing set to 1 or 2.
Without this patch, after the 7th message you got the WPS-CRED-RECEIVED
notification without the credentials. This was because the cred_attr and
cred_attr_len were not filled in in the wps structure.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Wrap self-generated WPS credential for new AP settings and send that to
control interface to provide the needed information in
WPS-NEW-AP-SETTINGS for external processing.
The Config Methods attribute in M2 and M2D messages is supposed to
indicate which configuration methods are supported by the Registrar. As
such, it should not depend on whether PBC mode is currently active or
not. That will only affect the Selected Registrar Config Methods and
Device Password ID attributes.
This adds the ability to add WPS vendor extensions to an AP (or GO).
They will be added to the WSC IE(s) in Beacon and Probe Response frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use only the UUID-E to remove active PBC session(s) at the completion of
successful PBC protocol run. This fixes potential issues with Enrollees
that use multiple MAC addresses and as such, can get multiple entries in
the PBC session list.
Use a specific return value, WPS-PBC-OVERLAP, to indicate a reason
for rejecting a wps_pbc command in wpa_supplicant AP mode if the
PBC mode cannot be started due to PBC session overlap having been
detected during monitor time.
This allows the user to complete WPS provisioning using PBC by
selected a specific Enrollee even if there are other Enrollees
in active PBC mode at the same time. The other Enrollees will be
rejected should they try to connect at the same time.
Ignore possible mismatches in the source address of the frame and only
use UUID-E to check whether a Probe Request or M1 is from the same
Enrollee when figuring out whether there is PBC session overlap. This
is needed to avoid potential issues with Enrollee devices that may have
multiple interfaces indicating active PBC state.
An optional parameter, p2p_dev_addr, can now be given to WPS_PBC
command on P2P GO to indicate that only the P2P device with the
specified P2P Device Address is allowed to connect using PBC. If
any other device tries to use PBC, a session overlap is indicated
and the negotiation is rejected with M2D. The command format for
specifying the address is "WPS_PBC p2p_dev_addr=<address>", e.g.,
WPS_PBC p2p_dev_addr=02:03:04:05:06:07
In addition, show the PBC session overlap indication as a WPS failure
event on an AP/GO interface. This particular new case shows up as
"WPS-FAIL msg=4 config_error=12".
Previously, only the Configuration Error values were indicated in
WPS-FAIL events. Since those values are defined in the specification
it is not feasible to extend them for indicating other errors. Add
a new error indication value that is internal to wpa_supplicant and
hostapd to allow other errors to be indicated.
Use the new mechanism to indicate if negotiation fails because of
WEP or TKIP-only configurations being disallows by WPS 2.0.
