The new hostapd.conf parameter sae_require_pmf=<0/1> can now be used to
enforce negotiation of MFP for all associations that negotiate use of
SAE. This is used in cases where SAE-capable devices are known to be
MFP-capable and the BSS is configured with optional MFP (ieee80211w=1)
for legacy support. The non-SAE stations can connect without MFP while
SAE stations are required to negotiate MFP if sae_require_mfp=1.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit b488a12948 ('Clear PMK length and
check for this when deriving PTK') started rejecting PTK derivation
based on PMK length. This reduced coverage from the eapol-fuzzer, so set
the default length when initializing the state machine in the fuzzer to
reach the previously used code paths.
Signed-off-by: Jouni Malinen <j@w1.fi>
Set Sc to 2^16-1 when moving to Accepted state per IEEE Std 802.11-2016,
12.4.8.6.5 (Protocol instance behavior - Confirmed state). This allows
the peer in Accepted state to silently ignore unnecessary
retransmissions of the Confirm message.
Signed-off-by: Jouni Malinen <j@w1.fi>
This implements the behavior described in IEEE Std 802.11-2016,
12.4.8.6.6 (Protocol instance behavior - Accepted state) to silently
discard received Confirm message in the Accepted state if the new
message does not use an incremented send-confirm value or if the special
2^16-1 value is used. This avoids unnecessary processing of
retransmitted Confirm messages.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd.conf parameter sae_sync (default: 5) can now be used to
configure the dot11RSNASAESync value to specify the maximum number of
synchronization errors that are allowed to happen prior to
disassociation of the offending SAE peer.
Signed-off-by: Jouni Malinen <j@w1.fi>
Wait for test/allocation failure for longer than the wait_fail_trigger()
default two seconds to allow DPP (in particular, PKEX) retransmission to
occur. This removes some issues where the previous wait was more or less
exactly the same duration as the retransmission interval and the first
Listen operation not always starting quickly enough to receive the first
frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
When executing ./start.sh with OpenSSL 1.1.0f, an OCSP operation fails.
Put "-sha256" ahead of "-serial" to fix this.
~# openssl version
OpenSSL 1.1.0f 25 May 2017
~# openssl ocsp -reqout /lkp/benchmarks/hwsim/tests/hwsim/logs/current/ocsp-req.der -issuer /lkp/benchmarks/hwsim/tests/hwsim/auth_serv/ca.pem -serial 0xD8D3E3A6CBE3CD12 -no_nonce -sha256
ocsp: Digest must be before -cert or -serial
ocsp: Use -help for summary.
~# openssl ocsp -reqout /lkp/benchmarks/hwsim/tests/hwsim/logs/current/ocsp-req.der -issuer /lkp/benchmarks/hwsim/tests/hwsim/auth_serv/ca.pem -sha256 -serial 0xD8D3E3A6CBE3CD12 -no_nonce
Signed-off-by: leishaoting <leist.fnst@cn.fujitsu.com>
Instead of requiring OpenSSL headers to be available just for the
SSL3_RANDOM_SIZE definition, replace that macro with a fixed length (32)
to simplify dependencies.
Signed-off-by: Jouni Malinen <j@w1.fi>
The patch offers alternate implementations of some functions using the
abstract cryptographic API.
This work was done in preparation for the changes to allow hostap to be
compiled with the wolfSSL cryptography and TLS library.
Signed-off-by: Sean Parkinson <sean@wolfssl.com>
This implements crypto_dh_init() and crypto_dh_derive_secret() using
os_get_random() and crypto_mod_exp() for all crypto_*.c wrappers that
include crypto_mod_exp() implementation.
Signed-off-by: Jouni Malinen <j@w1.fi>
A new vendor attribute QCA_WLAN_VENDOR_ATTR_GET_WEIGHED_PCL is added for
getting preferred channels with weight value and a flag to indicate how
the channels should be used in P2P negotiation process.
Signed-off-by: Peng Xu <pxu@qti.qualcomm.com>
Indicates the driver to use the RSNE as-is from the connect interface.
Exclusively used for the scenarios where the device is used as a testbed
device with special functionality and not recommended for production.
This helps driver to not validate the RSNE passed from user space and
thus allow arbitrary IE data to be used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously commit c79238b6a4 ('Define a
QCA vendor command to configure SAR Power limits') implemented a vendor
command interface to allow a userspace entity to dynamically control the
SAR power limits. Now implement a command to retrieve the current SAR
power limits.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new disable_fils parameter can be used to disable FILS functionality
in the driver. This is currently removing the FILS Capability bit in
Extended Capabilities and providing a callback to the driver wrappers.
driver_nl80211.c implements this using a QCA vendor specific command for
now.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows external programs to get the average channel utilization.
The average channel utilization is calculated and reported through
STATUS command. Users need to configure chan_util_avg_period and
bss_load_update_period in hostapd config to get the average channel
utilization.
Signed-off-by: Bhagavathi Perumal S <bperumal@qti.qualcomm.com>
Recalculate the timeout value for each event instead of calculating this
once and then not allowing the timeout configuration to be changed
without fully stopping and restarting the interface.
This allows the bss_load_update_period configuration parameter to be
modified while a BSS continues operating.
Signed-off-by: Bhagavathi Perumal S <bperumal@qti.qualcomm.com>
Do not update the configuration parameter before having verified the
value to be in the valid range.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Now that hostapd exposes the DPP_LISTEN and DPP_STOP_LISTEN commands
similarly to wpa_supplicant, expose these through proper hostapd_cli
commands as well to match wpa_cli functionality.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 265bda3444 ('OWE: Allow DH
Parameters element to be overridden for testing purposes') provided
means for using "VENDOR_ELEM_ADD 13 <IE>" in OWE protocol testing, but
that commit covered only the sme.c case (i.e., drivers that use
wpa_supplicant SME). Extend this to cover drivers that use internal SME
(e.g., use the nl80211 Connect command).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
owe_auth_req_process() can return NULL in error cases, but the caller
was not prepared for this. The p pointer cannot be overridden in such
cases since that would result in buffer length (p - buf) overflows. Fix
this by using a temporary variable to check the return value before
overriding p so that the hostapd_sta_assoc() ends up using correct
length for the IE buffer.
Fixes: 33c8bbd8ca ("OWE: Add AP mode handling of OWE with drivers that implement SME")
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The BoringSSL version of crypto_ecdh_init() and dpp_gen_keypair() works
fine with OpenSSL as well, so use that same implementation for both to
avoid unnecessary maintanence of multiple versions.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to go through EC_GROUP_new_by_curve_name(),
EC_KEY_new(), and EC_KEY_set_group() when a single call to
EC_KEY_new_by_curve_name() takes care of all that.
Signed-off-by: Jouni Malinen <j@w1.fi>
This reverts commit 5548453a2d since
BoringSSL added ECDSA_SIG_set0() and ECDSA_SIG_get0() in commit
8dc226ca8f1ef60737e1c1bf8cfcabf51d4068c7 ('Add some missing OpenSSL
1.1.0 accessors.') and updated X509_ALGOR_get0() prototype to match
OpenSSL 1.1.0 changes in commit e3b2a5d30d309091cab3e6a19dee7323c40d968d
('Const-correct X509_ALGOR_get0.').
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows wpa_supplicant configuration with phase1="tls_suiteb=1" to
use openssl_ciphers="ECDHE-RSA-AES256-GCM-SHA384" to further limit the
possible TLS cipher suites when using Suite B with RSA >3K keys. This
combination disables use of DHE and as such, mandates ECDHE to be used.
Signed-off-by: Jouni Malinen <j@w1.fi>
src/crypto/libcrypto.a and src/tls/libtls.a have circular references
and will need special handling with the linker at least for the time
being. This could be cleaned up eventually, but for now, provide a
mechanism to get the program linked.
This was already done in tests/Makefile, but tests/eapol-fuzzer/Makefile
needs the same.
Signed-off-by: Jouni Malinen <j@w1.fi>
These functions are a bit awkward to use for one-off file loads, as
suggested by the tls_clear_default_passwd_cb() logic. There was also
some historical mess with OpenSSL versions and either not having per-SSL
settings, having per-SSL settings but ignoring them, and requiring the
per-SSL settings.
Instead, loading the key with the lower-level functions seems a bit
tidier and also allows abstracting away trying both formats, one after
another.
Signed-off-by: David Benjamin <davidben@google.com>
There's no need to make an extra copy of private_key_passwd for
SSL_{CTX_,}set_default_passwd_cb().
Signed-off-by: David Benjamin <davidben@google.com>
Wpa_supplicant's random pool is not necessary on Android. Randomness
is already provided by the entropymixer service which ensures
sufficient entropy is maintained across reboots. Commit b410eb1913
'Initialize /dev/urandom earlier in boot' seeds /dev/urandom with
that entropy before either wpa_supplicant or hostapd are run.
Signed-off-by: Jeff Vander Stoep <jeffv@google.com>
Commit aab6612836 ('wlantest: Search
bss/sta entry more thoroughly for 4-address frames') allowed wlantest to
find a STA entry in this type of cases, but it was still possible for
that STA entry to be the one that has no derived PTK while the STA entry
for the other side of the link might have the derived PTK available.
Extend this BSS/STA selection mechanism to use sta->ptk_set to determine
which STA entry is more useful for decryption, i.e., select the one with
a known PTK.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
A new vendor attribute QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL is added
for vendor sub-command QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION.
This attribute is for setting the level of WLM.
Signed-off-by: Paul Zhang <paulz@qti.qualcomm.com>
