The freq and ht40 parameters can now be used with the p2p_invite
command when reinvoking a persistent group as the GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The variables used within the #ifndef block here needs to be defined in
the beginning of the function to avoid issues with some compilers.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This commit does not yet address support for different device roles,
i.e., the same set of subelements are returned regardless of which
role was indicated in the request.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_cli p2p_serv_disc_req command can now be used to request WSD
request to be sent to specified or all peers who support WSD.
format: wifi-display <list of roles> <list of subelements>
examples:
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source] 2,3,4,5
p2p_serv_disc_req 02:01:02:03:04:05 wifi-display [pri-sink] 3
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [sec-source] 2
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source+sink] 2,3,4,5
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source][pri-sink] 2,3,4,5
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This commit adds control interface commands and internal storage of
Wi-Fi Display related configuration. In addition, WFD IE is now added
to various P2P frames, Probe Request/Response, and (Re)Association
Request/Response frames. WFD subelements from peers are stored in the
P2P peer table.
Following control interface commands are now available:
SET wifi_display <0/1>
GET wifi_display
WFD_SUBELEM_SET <subelem> [hexdump of length+body]
WFD_SUBELEM_GET <subelem>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows both hostapd and wpa_supplicant to be used to derive and
configure keys for GCMP. This is quite similar to CCMP key
configuration, but a different cipher suite and somewhat different rules
are used in cipher selection. It should be noted that GCMP is not
included in default parameters at least for now, so explicit
pairwise/group configuration is needed to enable it. This may change in
the future to allow GCMP to be selected automatically in cases where
CCMP could have been used.
This commit does not included changes to WPS or P2P to allow GCMP to be
used.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit b49039bda9 redesigned tab
completion, but added the new call to completion functions into wrong
location. This needs to be done within the loop to find the correct
completion function.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
auto_interworking=1 configuration parameter can be used to request
wpa_supplicant to use Interworking network selection automatically as a
part of the normal (non-Interworking) network selection if the scan
results do not match with enabled networks. This makes scanning work
similarly to the "interworking_select auto" command.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new gas_request and gas_response_get commands can be used to request
arbitary GAS queries to be performed. These can be used with ANQP or
with other (including vendor specific) advertisement protocols.
gas_request <BSSID> <AdvProtoID> [Query]
gas_response_get <addr> <dialog token> [offset,length]
For example, ANQP query for Capability list in interactive wpa_cli
session:
> gas_request 02:00:00:00:01:00 00 000102000101
<3>GAS-RESPONSE-INFO addr=02:00:00:00:01:00 dialog_token=0
status_code=0 resp_len=32
> gas_response_get 02:00:00:00:01:00 00
01011c00010102010501070108010c01dddd0c00506f9a110200020304050607
> gas_response_get 02:00:00:00:01:00 00 0,10
01011c00010102010501
> gas_response_get 02:00:00:00:01:00 00 10,10
070108010c01dddd0c00
> gas_response_get 02:00:00:00:01:00 00 20,10
506f9a11020002030405
> gas_response_get 02:00:00:00:01:00 00 30,2
0607
It should be noted that the maximum length of the response buffer is
currently 4096 bytes which allows about 2000 bytes of the response data
to be fetched with a single gas_response_get command. If the response is
longer, it can be fetched in pieces as shown in the example above.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Clear the possible blacklisting of a WPS AP during WPS PIN iteration if
the AP moves to selected registrar TRUE state or if it adds our MAC
address to the list of authorized MACs.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Maintain state of WPS APs during iteration to find the correct AP for
WPS PIN operation when no specific BSSID is specified. This information
can be used for optimizing the order in which the APs are tried. This
commit is only adding the collection of the information and more
detailed debug information to make debug logs more helpful in figuring
out how the AP selection order could be improved.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This makes wpa_supplicant state somewhat cleaner since the information
from previously used connection is not maintained after getting
disconnected.
Signed-hostap: Jouni Malinen <j@w1.fi>
If 4-way handshake fails due to likely PSK failure or if EAP
authentication fails, disable the network block temporarily. Use longer
duration if multiple consecutive failures are seen.
Signed-hostap: Jouni Malinen <j@w1.fi>
"help <cmd>" can now be used to print the usage text for the
specified command (or set of commands matching the prefix).
Signed-hostap: Jouni Malinen <j@w1.fi>
Instead of using a separate list of commands, use the main command table
to assign tab completion functions. In addition, use the existing BSS
and P2P peer completions functions with the commands that use BSSID or
P2P Device address the first argument.
Signed-hostap: Jouni Malinen <j@w1.fi>
The NAI building routine assumed that the credential included the IMSI,
but that is not the case when using a real SIM card. Build the NAI based
on the IMSI read for the card in such a case.
Signed-hostap: Jouni Malinen <j@w1.fi>
The pos variable was not advanced when comparing PLMN entries in
3GPP Cellular Network information and as such, only the first
entry was really used.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
This can be used to test new control interface commands and to use
commands that may not yet be supported by wpa_cli.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the P2P management operations are handled within the driver, the
P2P service entries were not freed when terminating wpa_supplicant.
Fix this by calling wpas_p2p_service_flush() even if the P2P module
within wpa_supplicant has not been initialized.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This limits the maximum size of the p2p_client_list parameter that
is maintained at the GO for a persistent group. In other words, only
the 100 most recently seen P2P clients are kept in the list.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
This list can get truncated due to too many addresses getting added.
Reorder the entries in a way that allows the most recently added values
to be maintained in the list and use better debug/error messages when
parsing the value.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
Skip the end of long configuration lines that get truncated in
wpa_config_get_line(). Without this, the rest of the file was being
parsed as another line and that resulted in an unexpected error
message (wrong line number and wrong starting point).
In addition, increase the read buffer for network blocks from 256
to 2000 since p2p_client_list parameter can have long values. These
were supposed to truncated cleanly, but the unexpected processing of
the end of the file (which is now fixed in this commit) could cause
configuration file to be rejected.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
Commit 99fcd40409 added a call to update
search delay after failed authentication attempt. This change was
supposed to be only in p2p_supplicant.c for the successful case. The
extra call does not really do anything, but it's good to remove it to
avoid any confusion in the future.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, all station mode scan operations were either skipped or
delayed while any P2P operation was in progress. To make concurrent
operations easier to use, reduce this limitation by allowing a scan
operation to be completed in the middle of a p2p_find. In addition,
allow station mode association to be completed. When the station mode
operation is run to its completion (scan results not acted on,
connection to an AP completed, connection failed), resume the p2p_find
operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the p2p_find command is used without the delay parameter, a 500 ms
default search delay will now be used when any interface using the same
radio is in an concurrent operation. "p2p_find delay=0" can be used to
enforce the old behavior in such a case if needed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A new optional delay=<search delay in milliseconds> parameter can now be
used with p2p_find command to request an extra delay between search
iterations. This can be used, e.g., to make p2p_find friendlier to
concurrent operations by avoiding it from taking 100% of the radio
resources.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This EAP type uses a vendor specific expanded EAP header to encapsulate
EAP-TLS with a configuration where the EAP server does not authenticate
the EAP peer. In other words, this method includes only server
authentication. The peer is configured with only the ca_cert parameter
(similarly to other TLS-based EAP methods). This method can be used for
cases where the network provides free access to anyone, but use of RSN
with a securely derived unique PMK for each station is desired.
The expanded EAP header uses the hostapd/wpa_supplicant vendor
code 39068 and vendor type 1 to identify the UNAUTH-TLS method.
Signed-hostap: Jouni Malinen <j@w1.fi>
The WPA_AUTH_WPA and WPA_AUTH_WPA2 cases have already been rejected in
this function when execution comes here. In theory, support for
WPA-Enterprise could be added, but since that has not happened over the
years, there is no good reason to keep this dead code here.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit c9e08af24f removed the only user of
the special case MD5 use that would be allowed in FIPS mode in
tls_prf_sha1_md5(). Commit 271dbf1594
removed the file from the build, but left the implementation into the
repository. To clean things up even further, remove this functionality
completely since it is not expected to be needed for FIPS mode anymore.
Signed-hostap: Jouni Malinen <j@w1.fi>
Since we currently support only HS 2.0 networks with Interworking
network selection, do not indicate credential match unless the
network uses WPA2-Enterprise.
Signed-hostap: Jouni Malinen <j@w1.fi>
Since we currently support only HS 2.0 networks with Interworking
network selection, enforce that WPA2-Enterprise/CCMP is used on the
AP instead of allowing any WPA-Enterprise combination.
Signed-hostap: Jouni Malinen <j@w1.fi>
Hotspot 2.0 allows only WPA2-Enterprise to be used, so other types of
networks must not be indicated as Hotspot 2.0 networks even if they
(incorrectly) advertise HS 2.0 support.
Signed-hostap: Jouni Malinen <j@w1.fi>
When there was no credential match, but an enabled network block matched
with a scan result, wpa_supplicant reconnected at the end of
interworking_select command even if "auto" parameter was not used. Fix
this by running the reconnect only if requested to automatically select
a network.
Signed-hostap: Jouni Malinen <j@w1.fi>
If bgscan is enabled, then bgscan is initiated after the connection,
with no bss scan result information. Since a scan was performed prior to
the connection, the information exists and can be used to initialize the
bgscan's cache.
Signed-hostap: Yoni Divinsky <yoni.divinsky@ti.com>
When CONFIG_FIPS=y is used, do not include MD5 in the build and disable
EAPOL-Key frames that use MD5 (WPA/TKIP and dynamic WEP with IEEE
802.1X).
Signed-hostap: Jouni Malinen <j@w1.fi>
Only allow the TLS library keying material exporter functionality to be
used for MSK derivation with TLS-based EAP methods to avoid exporting
internal TLS keys from the library.
Signed-hostap: Jouni Malinen <j@w1.fi>
OpenSSL-based builds may need libdl in the linker line after the OpenSSL
library. CONFIG_TLS_ADD_DL=y can now be used to force that if needed.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used for convenience to build wpa_supplicant with OpenSSL
FIPS object module. CONFIG_FIPS=y is expected to be used in
wpa_supplicant/.config when using this option.
Signed-hostap: Jouni Malinen <j@w1.fi>
Increase GO config timeout if HT40 is used since it takes some time
to scan channels for coex purposes before the BSS can be started.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add optional "ht40" argument for p2p_group_add command to enable 40 MHz
in 5GHz band. This configures the secondary channel, when HT support is
enabled and if the HW supports 40 MHz channel width.
Signed-hostap: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
These helper functions can be used to implement most of the common
wpa_cli commands to simplify the implementation.
Signed-hostap: Jouni Malinen <j@w1.fi>
If key_mgmt was set to allow both WPA and non-WPA IEEE 802.1X (i.e., to
IEEE8021X WPA-EAP), non-WPA IEEE 802.1X was rejected while preparing
association parameters. Allow this special case to be handled by
selecting non-WPA case if the scan results for the AP do not include
either WPA or RSN elements.
Signed-hostap: Jouni Malinen <j@w1.fi>
Refactoring done in commit 46ee0427b1
(IEEE 802.11u: Allow Interworking and HESSID to be configured)
broke adding extra IEs in sched scan. The IEs stopped being added
to the scan params within wpa_supplicant_extra_ies() but no code
was added to add them in wpa_supplicant_req_sched_scan().
Fix this and remove unused params arg in wpa_supplicant_extra_ies().
Signed-hostap: Eyal Shapira <eyal@wizery.com>
intended-for: hostap-1
GAS_QUERY_TIMEOUT value was used for two different things - enum for
status callback and #define for internal eloop timeout). The latter
overwrites the former and as such, the timeout reported ended up going
out with value 5 which matches with GAS_QUERY_CANCELLED instead of
GAS_QUERY_TIMEOUT. This value was not used in existing code, so this
should not modify the current behavior. Anyway, the correct reason for
the failure should be reported. Rename the internal #define for the
timeout period to avoid the name conflict. [Bug 463]
Signed-hostap: Jouni Malinen <j@w1.fi>
There is no need to mandate admission control (ACM=1) by default, so
clear that flag in the case the configuration file does not specify
wmm_ac_{vo,vi}_acm value. This gets closer to the values mentioned
in the sample hostapd.conf file and reduces the need to specify WMM
parameters in the configuration file for most common use cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
In case of P2P GO and AP mode, wpa_supplicant uses the default hostapd
parameters for WMM. In the default parameters the ACM bit for video and
voice are set to 1, meaning, P2P devices and stations which are
connected to the GO cannot pass voice or video data packets. Allow this
to be changed through wpa_supplicant configuration file with wmm_ac_*
parameters.
Signed-hostap: Yoni Divinsky <yoni.divinsky@ti.com>
The os_memcmp of bssid and wpa_s->bssid cannot return 0 in this
code path since identical os_memcmp was already done above.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is the normal flow for association:
wpa_supplicant <--(EVENT_ASSOC event )-- device driver
wpa_supplicant --( get_bssid() )--> device driver
wpa_supplicant <--( return BSSID )-- device driver
However, a device driver could return EINVAL for get_bssid() because it
recognizes it has already been disconnected. When the wpa_supplicant
received EINVAL, the bssid field could be used uninitialized in the
following flow:
wpa_supplicant <--(EVENT_ASSOC event )-- device driver
device driver (receive deauth)
wpa_supplicant --( get_bssid() )--> device driver
wpa_supplicant <--( return EINVAL )-- device driver
Prevent this by requiring the get_bssid() call to succeed when
processing association events.
Don't assume the 11g mode is always first in the list of mode (sometimes
it isn't). Traverse the array of modes and check the HT40 capability is
turned on for 11g.
Signed-hostap: Arik Nemtsov <arik@wizery.com>
wpa_s->removal_reason was set only when calling wpas_p2p_group_delete()
and while couple of call places did not set this, it should really be
set in each case. As such, it works better as a function parameter than
a variable in struct wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
p2p_group_remove should only attempt to remove P2P group
interfaces and fail on non-P2P group interfaces.
Signed-hostap: Michael Naumov <michael.naumov@intel.com>
Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
This enables setting a different max inactivity timeout for P2P GO.
This timeout is used to detect inactive clients. In some scenarios
it may be useful to have control over this and set a shorter timeout
than the default 300s. For example when running STA and P2P GO interfaces
concurrently, the STA interface may perform scans which may cause the
GO to miss a disassoc / deauth frames from a client and keep assuming
that the client is connected until the inactivity detection kicks in.
300 secs is a bit too long for such scenarios and creates a bad user
experience.
Signed-hostap: Eyal Shapira <eyal@wizery.com>
This simplifies the implementation by using the buffer type to which the
returned data will be converted anyway. This avoids one memory
allocation for each processed RADIUS message.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new ssid2 parameter can be used as an alternative mechanism for
configuring SSID for hostapd. It uses the same formats that
wpa_supplicant uses in the configuration file for strings.
Signed-hostap: Jouni Malinen <j@w1.fi>
P"<escaped string>" can now be used as an alternative method for
specifying non-ASCII strings (including control characters). For
example, ssid=P"abc\x00test".
Signed-hostap: Jouni Malinen <j@w1.fi>
Process CTRL-EVENT-TERMINATING in wpa_cli interactive mode and close
ctrl_iface connection without trying to detach the monitor interface
when this happens. This avoids a timeout on the DETACH command. In
addition, print out connection lost/re-established messages without
overriding the edit line.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is needed to allow the default behavior (pick first interface) to
be used in cases where wpa_supplicant is not available when wpa_cli is
started in interactive mode.
Signed-hostap: Jouni Malinen <j@w1.fi>
wpa_ctrl_get_remote_ifname() is defined only for UDP ctrl_iface socket,
so this call needs to be made conditional on build parameters.
Signed-hostap: Jouni Malinen <j@w1.fi>
This changes the call flow to allow full eloop operations to be used
while waiting for wpa_cli to establish a connection to wpa_supplicant in
the beginning of an interactive session. This allows the cleanup steps
to be more consistent and avoid debugging issues due to unfreed memory
or other resources if wpa_cli is killed with Ctrl-c.
Signed-hostap: Jouni Malinen <j@w1.fi>
When starting interactive mode, wpa_cli is trying to attach the
monitor connection. If that fails, the operation is retried, but
this was done without freeing all the resources that could have
been allocated (mainly, the command connection).
Signed-hostap: Jouni Malinen <j@w1.fi>
When CONFIG_CTRL_IFACE=udp-remote is used, print user frendly PS in
wpa_cli. E.g.,
localhost/wlan0>
192.168.1.1/p2p-wlan-0-0>
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Add new option for ctrl iface: CONFIG_CTRL_IFACE=udp-remote. This
enables remote access to control interface via UDP port(s). This should
be used for testing purpose only since there is no authentication or
access control on the commands.
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
The network_object path should be returned by the NetworkAdded signal
and not by the GroupStarted Signal. Starting a Group does not
necessarily validate the network object.
Signed-hostap: Michael Naumov <michael.naumov@intel.com>
Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
intended-for: hostap-1
D-Bus script using python glib is added to perform Disconnect on an
interface.
Signed-hostap: Michael Naumov <michael.naumov@intel.com>
Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
D-Bus script using python glib is added to perform p2p_invite on a group
interface to invite a peer.
Signed-hostap: Michael Naumov <michael.naumov@intel.com>
Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
dev.config_methods was not updated when wps_update_config was called.
This could lead to mismatching config methods between Probe Request and
M1 packets. Add missing part for it.
This allows the password parameter for EAP methods to be fetched
from an external storage.
Following example can be used for developer testing:
ext_password_backend=test:pw1=password|pw2=testing
network={
key_mgmt=WPA-EAP
eap=TTLS
identity="user"
password=ext:pw1
ca_cert="ca.pem"
phase2="auth=PAP"
}
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows wpa_supplicant configuration file to be created without
the PSK/passphrase value included in the file when a backend for
external password storage is available.
Following example can be used for developer testing:
ext_password_backend=test:psk1=12345678
network={
ssid="test-psk"
key_mgmt=WPA-PSK
psk=ext:psk1
}
Signed-hostap: Jouni Malinen <j@w1.fi>
This new mechanism can be used to make wpa_supplicant using external
storage (e.g., key store in the operating system) for passwords,
passphrases, and PSKs. This commit is only adding the framework part
needed to support this, i.e., no actual configuration parameter can
yet use this new mechanism. In addition, only a simple test backend
is added to allow developer testing of the functionality.
Signed-hostap: Jouni Malinen <j@w1.fi>
Instead of rejecting network blocks without PSK/passphrase at the time
the configuration file is read, allow such configuration to be loaded
and only behave as if the network block with missing PSK/passphrase is
disabled.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, this was left to the default (WPA-EAP WPA-PSK) value which
could potentially result in unexpected behavior if an AP were to enable
both WPA2-Enterprise and WPA2-Personal in the same BSS. While this is
not really that likely for APs supporting Interworking, it is good to
get the PSK option removed to avoid any issues with missing
passphrase/PSK configuration parameter.
Signed-hostap: Jouni Malinen <j@w1.fi>
Each cred block can now be matched based on Roaming Consortium OI as an
alternative mechanism to using NAI Realm information. This may be
optimized for efficiency in the future since Roaming Consortium
information is available in scan results without having to go through
ANQP queries. In addition, this is easier to support in case there is a
large number of realms that can be used for authentication.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new cred block parameters eap, phase1, and phase2 can be used to
select which EAP method is used with network selection instead of using
the value specified in ANQP information (e.g., NAI Realm).
Signed-hostap: Jouni Malinen <j@w1.fi>
Allow the user to configure an RSSI threshold in dBm below which the
nl80211 driver won't report scan results. Currently only supported
during scheduled (PNO) scans.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
P2P group is only going to use a single GO, so we can leave the fixed
BSSID parameter set for the actual data connection in addition to the
initial WPS provisionign step. This can speed up operations with drivers
that select BSS internally by allowing them to skip an extra scan when
the BSSID and frequency of the GO is already known.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Four D-Bus scripts using python glib are added to perform the following
operations: p2p_flush, p2p_group_add, p2p_listen and p2p_stop_find.
Signed-hostap: Michael Naumov <michael.naumov@intel.com>
Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
Commit 7c865c6853 introduced a code
path that can skip extra_ie initialization in wpa_supplicant_scan().
This could result in semi-random crashes when using the autoscan
mechanism. Fix this by initializing extra_ie to NULL.
Signed-hostap: Jouni Malinen <j@w1.fi>
This updates the license notification to use only the BSD license. The
changes were acknowledged by email (Kel Modderman <kel@otaku42.de>,
Mon, 2 Jul 2012 20:02:37 +1000).
Signed-hostap: Jouni Malinen <j@w1.fi>
This updates these files to use the license notification that uses only
the BSD license. The changes were acknowledged by email (Dan Williams
<dcbw@redhat.com>, Sun, 01 Jul 2012 15:53:36 -0500).
Signed-hostap: Jouni Malinen <j@w1.fi>
This functionality could be shared for other commands, too, so move
it to a common function. In addition, implement the validation in a
bit more strict way to avoid accepting values like '-123' as a valid
PIN.
Signed-hostap: Jouni Malinen <j@w1.fi>
Reject invalid PIN value in p2p_connect command. Before this, typos
like "pbd" as the third parameter could have resulted in OK return
value since this parameter was interpreted as the PIN.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
When a special scan_res_handler is used the scan parameters may not have
been suitable for other purposes (e.g., during a p2p_find operation). As
such, do not indicate such scan results to other virtual interfaces
using the same radio.
Signed-hostap: Jouni Malinen <j@w1.fi>
In the properties changed signal, added a new property
"DisconnectReason", which carries the IEEE 802.11 reason code of the
most recent disassociation or deauthentication event. The reason code is
negative if it is locally generated. The property is sent to the DBUS
immediately so as to prevent it from being coalesced with other
disconnect events.
Signed-off-by: Gary Morain <gmorain@chromium.org>
Two DBUS scripts using python glib are added to perform p2p_find and
p2p_connect operations respectively. p2p_connect script just performs
the traditional connect to create a new p2p group. Additional updates
will be required to perform join, auth etc. al.
Signed-hostap: Michael Naumov <michael.naumov@intel.com>
Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
nfc_pw_token can be used to build random NFC password token for WPS.
This tool prints out the wpa_supplicant.conf (or hostapd.conf)
parameters and the hexdump of the WPS password token (with and without
NDEF encapsulation) so that it can be written to a NFC tag with an
external program.
Signed-hostap: Jouni Malinen <j@w1.fi>
os_random() may not be seeded properly, so use stronger mechanism for
generating the password id for NFC password tokens.
Signed-hostap: Jouni Malinen <j@w1.fi>
The AP PIN on wps_reg command can now be replaced with special value
"nfc-pw" to use device password from a NFC password token from the AP.
Signed-hostap: Jouni Malinen <j@w1.fi>
WPS_ER_NFC_CONFIG_TOKEN command can now be used to build a NFC
configuration token based on AP Settings learnt with WPS_ER_LEARN
or set with WPS_ER_CONFIG.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new wpa_supplicant ctrl_iface command WPS_NFC_TAG_READ can now be
used to process NFC tags read by external programs to initiate
wpa_supplicant to use NFC Configuration Token to create a new network.
Signed-hostap: Jouni Malinen <j@w1.fi>
Instead of requiring low-level access to an NFC device and synchronous
operations, the new WPS_NFC_TOKEN and WPS_NFC ctrl_iface commands can be
used to build a NFC password token and initiate WPS protocol run using
that token (or pre-configured values) as separate commands. The
WPS_NFC_TOKEN output can be written to a NFC tag using an external
program, i.e., wpa_supplicant does not need to have low-level code for
NFC operations for this.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, a pending scan request could be left running when processing
DISCONNECT command from control interface. This can result in unexpected
scan, so cancel the request to avoid this.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use wpa_supplicant_set_state() to initialize state to DISCONNECT so that
autoscan gets initialized properly. This needs a change in
autoscan_init() to avoid extra scan request that would postpone the
first scan request when an interface is added.
Signed-hostap: Jouni Malinen <j@w1.fi>
The first time the limit is exceeded could result in using larger
value - avoid that by limiting the interval also in that case.
Signed-hostap: Jouni Malinen <j@w1.fi>
This module will sets a fixed scanning interval. Thus, the parameter to
this module is following this format: <fixed interval>
Signed-hostap: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This module will compute the interval on a base exponential. Thus,
params to this module are following this format: <base>:<limit>
Signed-hostap: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Like bgscan, autoscan is an optional module based feature to automate
scanning but while disconnected or inactive.
Instead of requesting directly a scan, it only sets the scan_interval
and the sched_scan_interval. So, if the driver supports sched_scan,
autoscan will be able to tweak its interval. Otherwise, the tweaked
scan_interval will be used. If scan parameters needs to be tweaked, an
autoscan_params pointer in wpa_s will provide those. So req_scan /
req_sched_scan will not set the scan parameters as they usually do, but
instead will use this pointer.
Modules will not have to request a scan directly, like bgscan does.
Instead, it will need to return the interval it wants after each
notification.
Signed-hostap: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Some drivers may independently decide to switch channels. Handle this by
updating the hostapd and wpa_supplicant AP and GO configuration.
Signed-hostap: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Some of the authentication/association failure paths left wpa_state to
its previous value. This can result in unexpected behavior when
wpa_supplicant tries to find an AP to connect to since the uncleared
state can result the in the selected BSS being ignored if it is same as
the previously used BSS. This could happen, e.g., when wpa_supplicant
SME was used and the AP rejected authentication. Fix this by explicitly
setting state to DISCONNECTED on auth/assoc failures that did not yet do
this.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
A p2p_find during provisioning shall not allow the enrollee to
pick the network, hence disable p2p_find during provisioning.
Signed-hostap: Sunil Dutt Undekari <duttus@codeaurora.org>
The wpas_p2p_pd_before_join_timeout could be left behind if the PD
Request in p2p_connect-auto case does not succeed. This timeout can
result in unexpected operations since it could trigger join operation
while going through GO Negotiation. Fix this by canceling the timeout
when falling back to GO Negotiation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add an additional parameter to prioritize either sta or p2p connection
to resolve conflicts arising during single channel concurrency.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
This avoids issues with some APs rejecting a reassociation if the
station is not currently associated as reported by Yossi Wortzel.
The change is based on a patch from Arik Nemtsov.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 361cdf3400 changed the way the
group formation timeout is used on P2P client. However, it resulted in
clearing the timeout on the GO when the GO started beaconing. This is
not correct since the timeout is supposed to be maintained until at
least the completion of the WPS provisioning step. Fix this regression
by clearing the timeout here only in the case we are not GO in group
formation phase.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for wpa_state to be WPA_DISCONNECTED when a new scan is
scheduled to be started in the future. If wpas_wps_cancel() gets called
(e.g., through control interface wps_cancel or a P2P group removal)
while in that state, the WPS operation (scan request and special network
block) were not removed. Fix this by clearing the WPS operations both in
WPA_SCANNING and WPA_DISCONNECTED states.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
The previous version set scan_res_handler unconditionally and then
cleared it if scan request failed. This can result in incorrect clearing
of the handler to NULL for a previously started scan that has not yet
completed. This can make p2p_find command fail to use the
start-after-scan-completion mechanism in some cases. Fix this by setting
scan_res_handler properly after having verified that the driver command
for starting the scan was successful.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
Perform addition additional scan runs on the operating channel of the GO
(if known from previous scan results) and fall back to initiate the PD
for GO Negotiation if these additional scans do not detect the peer as
GO.
Signed-hostap: Sunil Dutt Undekari <duttus@codeaurora.org>
Commit 361cdf3400 extended the use of
group formation timeout for the way handshake, but the registration was
done on the group_interface while the cancellation was done on the
parent interface. Fix the registration to set the eloop timeout on
parent to address potential issues when using a separate group
interface.
Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
When looking for a BSS to eject due to too many entries, never
pick one that is in use. Otherwise, we run the risk of having
pointers to freed data.
Signed-hostap: Paul Stewart <pstew@chromium.org>
Send an "EAP" signal via the new DBus interface under various
conditions during EAP authentication:
- During method selection (ACK and NAK)
- During certificate verification
- While sending and receiving TLS alert messages
- EAP success and failure messages
This provides DBus callers a number of new tools:
- The ability to probe an AP for available EAP methods
(given an identity).
- The ability to identify why the remote certificate was
not verified.
- The ability to identify why the remote peer refused
a TLS connection.
Signed-hostap: Paul Stewart <pstew@chromium.org>
Use an empty IPv4 packet as the keep-alive packet for WNM BSS max idle
period mechanism. This is not really the best possible frame to use for
this, but for now, it can do until a more suitable frame is figured out
for this (e.g., special LLC header to indicate link test purposes).
Signed-hostap: Jouni Malinen <j@w1.fi>
If WNM is enabled for the build (CONFIG_WNM=y), add BSS max idle period
information to the (Re)Association Response frame from the AP and parse
this information on the station. For SME-in-wpa_supplicant case, add a
timer to handle periodic transmission of the keep-alive frame. The
actual request for the driver to transmit a frame is not yet
implemented.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit aa9bb7644b improved robustness
of p2p_connect-auto mechanism by using older scan results to help in
determination whether the peer was operating a GO. Improve this by
accepting new GO information from scan-for-WPS-provisioning results
even if the GO is not yet ready for WPS.
In addition, fix an issue where Provision Discovery exchange timeout
could have left offchannel TX operation in progress when the fallback
was used.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This is a workaround for interoperability issues with some deployed P2P
implementations that require a Provision Discovery exchange to be used
before GO Negotiation. The new provdisc parameter for the p2p_connect
command can be used to request this behavior without having to run a
separate p2p_prov_disc command.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Excessive debug level can now be used to dump the IEs received in scan
results from both Beacon and Probe Response frames. This makes it easier
to debug issues where the driver (or well, more likely cfg80211) does
not update the IEs based on Beacon frames if even a single Probe
Response frame has been received.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, wpa_supplicant did not specify BSSID to any connection
request if the driver indicated that it will take care of BSS selection.
This is fine for most use cases, but can result to issues if the network
block has an explicit bssid parameter to select which BSS is to be used.
Fix this by setting BSSID and channel when the network block includes the
bssid parameter even if the driver indicates support for BSS selection.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
If WPS commands are used with a specific BSSID instead of wildcard,
the BSSID that was supposed to be used only for the provisioning step
may end up getting copied to the network block that gets provisioned
based on the WPS credentials. Fix this by clearing ssid->bssid_set
when creating the network block by replacing the block used for WPS
provisioning.
This issue could show up with the provisioned network not getting
selected properly with APs that have multiple radios. Depending on
the driver, this could result in only a single one of the available
BSSes being available or the connection failing completely.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
The nl80211 driver interface does not allow 128-bit WEP to be used
without a vendor specific cipher suite and no such suite is defined for
this purpose. Do not accept WEP key length 16 for nl80211 driver
interface forn ow. wext-interface can still try to use these for
backwards compatibility.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
I think this should fix the following valgrind complaint:
==1972== Source and destination overlap in memcpy(0x5181708, 0x5181708, 16)
==1972== at 0x4A073BA: memcpy (mc_replace_strmem.c:602)
==1972== by 0x45872B: wpas_wps_set_uuid (wps_supplicant.c:1116)
==1972== by 0x4599EC: wpas_wps_update_config (wps_supplicant.c:1747)
==1972== by 0x4C8DB0: wpa_supplicant_update_config (wpa_supplicant.c:3090)
==1972== by 0x4C3E5E: wpa_supplicant_reload_configuration (wpa_supplicant.c:746)
==1972== by 0x4B8B37: wpa_supplicant_ctrl_iface_process (ctrl_iface.c:4082)
==1972== by 0x4BA39C: wpa_supplicant_ctrl_iface_receive (ctrl_iface_unix.c:168)
==1972== by 0x4114D4: eloop_sock_table_dispatch_table (eloop.c:335)
==1972== by 0x411541: eloop_sock_table_dispatch (eloop.c:352)
==1972== by 0x41200D: eloop_run (eloop.c:766)
==1972== by 0x4C8B43: wpa_supplicant_run (wpa_supplicant.c:3010)
==1972== by 0x4D44AD: main (main.c:286)
Signed-hostap: Ben Greear <greearb@candelatech.com>
intended-for: hostap-1
The P2P implementation assumes that the first wpa_s interface instance
is used to manage P2P operations and the P2P module maintains a pointer
to this interface in msg_ctx. This can result in issues (e.g., use of
freed memory) when the management interface is removed. Fix this by
deinitializing global P2P data if the interface that created it is
removed. This will disable P2P until the next interface is added.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
If the AP indicates support for Hotspot 2.0, show this in the
ctrl_iface commands for BSS table and status.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There are no plans to continue making the Windows binary package for
wpa_supplicant for 1.x or newer releases, so remove the scripts and
notes that are related to this.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used with P2P management operations that need to verify
whether the local device is operating a specific group based on
P2P Group ID attribute from a peer.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previusly the peer was assumed to not be operating a GO if the BSS entry
for it was not updated in the single scan run started by
p2p_connect-auto. This is not very robust since a scan may miss the peer
if either a Probe Request or Probe Response frame is lost. Improve
robustness by assuming the peer is still operating the GO and starting
the join operation. If the GO is not found during PD-for-join or the
single-channel scans during the join, fall back to GO Negotiation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Do not try to associate with a network that has an invalid or incomplete
configuration because the association or at least data connection would
fail anyway. This commits adds a common function for checking whether a
network block is disabled to make it easier to check network blocks
without having to reject them during configuration file parsing (which
would prevent wpa_supplicant from starting). The only additional check
added in this commit is to verify the WEP key length. Similar checks for
other parameters can be added in future commits.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds the copyright notice for Intel and moves to the license
notification that uses only the BSD license. The changes were
acknowledged by email ("Berg, Johannes" <johannes.berg@intel.com>,
Mon, 7 May 2012 07:33:53 +0000).
Signed-hostap: Jouni Malinen <j@w1.fi>
Both EAP-AKA and EAP-AKA' use USIM. Without this change, use of real
USIM card for EAP-AKA' was not allowed to proceed, i.e., only the
software simulated USIM operations were supported.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
This workaround for Windows 7 WPS probing mechanism was previously
allowed only with hostapd, but the same interoperability issue can
happen with wpa_supplicant AP/GO mode. Allow the workaround to be
enabled in wpa_supplicant configuration for these uses.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed to allow the max_sta_num parameter set in the main
configuration file to apply to dynamically created P2P group
interfaces.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
Since we are reporting 20/40 BSS coex information only for 2.4 GHz band,
there is no need to run the full scan on dualband cards.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add support for HT STA to report 40 MHz intolerance to the associated AP.
A HT station generates a report (20/40 BSS coexistence) of channel list
if it finds a non-HT capable AP or a HT AP which prohibits 40 MHz
transmission (i.e., 40 MHz intolerant bit is set in HT capabilities IE)
from the scan results.
Parse the OBSS scan parameter from Beacon or Probe Response frames and
schedule periodic scan to generate 20/40 coexistence channel report if
requested to do so. This patch decodes Scan Interval alone from the OBSS
Scan Parameters element and triggers scan on timeout.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 7de5688d68 started using
wpa_supplicant_ctrl_iface_ctrl_rsp_handle() from the D-Bus code, but
left this function in ctrl_iface.c that is included conditionally. Fix
this by moving the common function into wpa_supplicant.c so that it can
be included for builds that include only either ctrl_iface or D-Bus.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
An existing persistent group information can now be used to force GO
Negotiation to use the previously used SSID/passphrase from a persistent
group if we become a GO. This can be used as an alternative to inviting
a new P2P peer to join the group (i.e., use GO Negotiation with GO
intent 15 instead of starting an autonomous GO and using invitation),
e.g., in case a GO Negotiation Request is received from a peer while we
are not running as a GO. The persistent group to use for parameters is
indicated with persistent=<network id> parameter to p2p_connect.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant can now be requested to automatically figure out whether
the indicated peer is operating as a GO and if so, use join-a-group
style PD instead of pre-GO Negotiation PD.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The p2p_dev_addr parameter in the P2P-PROV-DISC-FAILURE event (added in
commit f65a239ba4) was supposed to the P2P
Device Address of the peer, not the local device.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The man page source was not up-to-date with removed driver wrappers,
so bring in the wpa_supplicant/README changes to make this somewhat
closer to the current state.
Signed-hostap: Jouni Malinen <j@w1.fi>
Make wpa_supplicant_event() more consistent by not checking
data in either location handling EVENT_RX_MGMT events. This event
is required to specify the data so this pointer cannot be NULL.
Signed-hostap: Jouni Malinen <j@w1.fi>
In most languages, DBus dictionaries are mapped to either sorted maps
or hash tables, so you can't control the actual ordering of the
generated a{sv}. Relying on ordering in this method is unnecessary and
makes it use from DBus much harder.
Signed-hostap: Adrien Bustany <adrien.bustany@nokia.com>
Add provisional discovery failure ctrl_iface event
(P2P-PROV-DISC-FAILURE) to indicate to the application layer in case of
PD failure.
Signed-off-by: Deepthi Gowri <deepthi@codeaurora.org>
When the network configuration includes exactly the number of
scan_ssid=1 networks as the driver supports for scan_sched and no
networks need wildcard SSID scan, there is no need to use sched_scan
timeout. Check this condition and optimize this case to avoid the extra
sched_scan start/stop operations.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The debug messages were showing the opposite of what the actual
implementation was doing for sched_scan timeout.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This new configuration parameter can be used to disable automatic
offloading of scan requests to the driver which was previously used
by default if the driver supported sched_scan.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Using the socket command interface, it is possible to pass a NULL dst to
wpas_p2p_sd_request, however you could not do so using the D-Bus API,
since it required a valid Peer object path. This patch changes the
behavior, so that if the "peer_object" is missing from the parameters,
a NULL dst is passed to wpas_p2p_sd_request.
Signed-hostap: Adrien Bustany <adrien.bustany@nokia.com>
intended-for: hostap-1
This patch cleans up the P2PDevice D-Bus interface for the hostap-1
release. A spelling error is corrected and P2PDeviceProperties is
renamed to clarify that this data is configuration data and not the
total collection of Properties for the P2PDevice interface.
Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
Signed-hostap: Angie Chinchilla <angie.v.chinchilla@intel.com>
intended-for: hostap-1
The D-Bus property getters should not return an error when the
properties are not valid/relevant. Returning an error breaks the
GetAll method in the dbus interface. Change Group and PeerGO
property getters to make GetAll work on P2PDevice.
Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
Signed-hostap: Angie Chinchilla <angie.v.chinchilla@intel.com>
intended-for: hostap-1
A special value p2p_group_idle=-1 can now be used to configure the P2P
group idle mechanism to terminate a P2P client group immediately on any
disconnection after the completion of the initial 4-way handshake.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Instead of relying on the P2P group idle timeout before the group
connection has been fully established, re-start the group formation
timeout in the end of the WPS provisioning step and clear it at the
successful completion of the initial 4-way handshake. This allows the
P2P group idle timeout to be set to a small value without triggering it
during the initial scan and connection attempt.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_drv_scan() may fail for the initial p2p_connect join scan request,
e.g., if the driver happened to be scanning at the time the new
operation was initialized. Previously, a special scan result handler was
registered regardless of whether the new scan was started. This could
result in partial scan results (e.g., from p2p_find social scan) from
being used as full results for join (or now more importantly for
p2p_connect auto) purposes. Fix this by registering the new scan result
handler only if wpa_drv_scan() returns success.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_connect command can now be used with an optional "auto" parameter
to request wpa_supplicant to determine automatically whether to use
join-a-group operation (if the peer is operating as a GO) or group
formation. This makes it easier for external programs to handle
connection type selection by offloading this to wpa_supplicant. The
previously used p2p_connect join commands can be replaced with
p2p_connect auto to use this new mechanism.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The previous commit did not use the correct pointer in all operations
and was specific to station mode interfaces. Fix and extend it to work
with AP/GO interfaces, too.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the driver does not indicate support for multi-channel concurrency,
abort join-group operation if the end result would result in use of
multiple operating frequencies with the same radio.
Signed-hostap: Jouni Malinen <j@w1.fi>
This brings up the changes from defconfig into the Android configuration
file, but does not change any of the actual build parameters.
Signed-hostap: Jouni Malinen <j@w1.fi>
This was never really completed and is of not much use at this point,
so clean up the repository by removing the Symbian-specific changes.
Signed-hostap: Jouni Malinen <j@w1.fi>
This optional parameter to the BSS command can be used to select which
fields are included in the output to avoid having to parse through
unneeded information and to reduce the buffer size.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
When a supplicant is deinited and shutting, disconnect from P2P groups.
This fixes a memory leak on variable dbus_groupobj_path on exiting
supplicant.
Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
Signed-hostap: Angie Chinchilla <angie.v.chinchilla@intel.com>
When forming a P2P group using WSC PIN method, if the PIN is entered
incorrectly the P2P client supplicant instance will crash as a result
of cleanup happening on data that is still in use in a case where a
separate P2P group interface is used.
For example, here is the path for the first crash:
eap_wsc_process():
- creates struct wpabuf tmpbuf; on the stack
- sets data->in_buf = &tmpbuf;
- calls wps_process_msg()
- which calls wps_process_wsc_msg()
- which, in case WPS_M4: calls wps_fail_event()
- which calls wps->event_cb()
- wps->event_cb = wpa_supplicant_wps_event()
- wpa_supplicant_wps_event()
- wpa_supplicant_wps_event_fail()
- which calls wpas_clear_wps()
- which calls wpas_notify_network_removed()
- which calls wpas_p2p_network_removed()
- which calls wpas_p2p_group_formation_timeout()
- which calls wpas_group_formation_completed()
- which calls wpas_p2p_group_delete()
- which calls wpa_supplicant_remove_iface()
- which calls wpa_supplicant_deinit_iface()
- which calls wpa_supplicant_cleanup()
- which calls eapol_sm_deinit()
- ... which eventually uses the ptr data->in_buf to free tmpbuf, our
stack variable and then the supplicant crashes
If you fix this crash, you'll hit another. Fix it and then a segfault.
The way we're cleaning up and deleting data from under ourselves here
just isn't safe, so make the teardown portion of this async.
Signed-hostap: Angie Chinchilla <angie.v.chinchilla@intel.com>
Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
intended-for: hostap-1
There is no need to force this configuration parameter to be written
into the configuration file for each network block that has not modified
the default value.
Signed-hostap: Jouni Malinen <j@w1.fi>
I think this comment, as originally stated, says the opposite of
what is meant. Reword to help the next guy.
Signed-hostap: Angie Chinchilla <angie.v.chinchilla@intel.com>
For concurrency scenarios we should not update the scan results without
P2P IE to P2P group interfaces. This patch is to take care if a scan has
been requested on STA interface and scan results are getting updated
from sibling to P2P group interface. A P2P GO Probe Response for a
legacy STA scan would be without P2P IE. So it will wrongly update the
BSS list of P2P group interface too when results are updated from
sibling.
Since P2P group interfaces are used only for connecting to a P2P group,
it is fine to filter out all non-P2P entries from their BSS table.
Signed-off-by: Neeraj Garg <neerajkg@broadcom.com>
For debugging I needed to look at the frames in a wpa_supplicant debug
log. Looking at the hexdump is a bit tedious, so I wrote a quick script
to convert the nl80211 debugging output to a PCAP file that can be
opened in wireshark.
I've polished the initial raw script a bit to add error messages and to
also record the timestamps to the pcap file.
Hopefully it's useful to somebody else as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wps_vendor_ext_m1 configuration parameter can now be used to add a
vendor specific attribute into the WPS M1 message, e.g., for
Windows Vertical Pairing.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The GO can indicate that the P2P Group session is ending by sending a
Deauthentication frame with reason code 3 (Deauthenticated because
sending STA is leaving) based on P2P specification section 3.2.9. Use
this reason code to remove the P2P client group without waiting for the
group idle timeout.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpas_notify_state_changed() notified about disconnection when
new_state < WPA_ASSOCIATED, without checking the old state. This
results in extra processing which can be avoided by checking that
old_state was connected.
Signed-hostap: Eliad Peller <eliad@wizery.com>
intended-for: hostap-1
On P2P group removal, the GO is deinitialized correctly (and the vif
mode is set back to sta in case of nl80211), but the P2P client mode
wasn't deinitialized, and the nl80211 vif stays in P2P client mode.
Add a new deinit_p2p_cli op (similar to deinit_ap), which currently only
sets the interface back to station mode.
Signed-hostap: Eliad Peller <eliad@wizery.com>
intended-for: hostap-1
Commit 2d43d37ff2 broke EVENT_RX_MGMT
processing in wpa_supplicant AP mode. ap_mgmt_rx() needs to be called
for Probe Request frames even if they get notified through the new
D-Bus signal mechanism.
Signed-hostap: Jouni Malinen <j@w1.fi>
Some applications require knowing about probe requests to identify
devices. This can be the case in AP mode to see the devices before they
connect, or even in P2P mode when operating as a P2P device to identify
non-P2P peers (P2P peers are identified via PeerFound signals).
As there are typically a lot of probe requests, require that an
interested application subscribes to this signal so the bus isn't always
flooded with these notifications. The notifications in DBus are then
unicast only to that application.
A small test script is also included.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The signal strength is currently never used as the only driver reporting
it is nl80211 which uses IEEE80211_RADIOTAP_DB_ANTSIGNAL which is never
populated by the kernel. The kernel will (soon) populate
IEEE80211_RADIOTAP_DBM_ANTSIGNAL instead though, so use that.
Also, since it was never really populated, we can redefine the signal
field to be in dBm units only.
My next patch will also require knowing the signal strength of probe
requests throughout the code (where available), so add it to the
necessary APIs.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Enable control of wpa_s->scan_interval via D-Bus. This parameter
controls the delay between successive scans for a suitable AP.
Also, update dbus.doxygen with ScanInterval, and some other
parameters that were undocumented.
Signed-hostap: Mukesh Agrawal <quiche@chromium.org>
Some of the standard lib functions being used directly are redefined in
src/utils/os.h thus providing an abstraction. Change code to use os_*
functions instead of directly using the lib functions.
Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
Signed-hostap: Angie Chinchilla <angie.v.chinchilla@intel.com>
Add the option (-T) to wpa_supplicant to log all debug messages into the
kernel tracing, allowing to aggregate kernel debugging with
wpa_supplicant debugging and recording all with trace-cmd.
Since tracing has relatively low overhead and can be filtered
afterwards, record all messages regardless of log level. However, it
will honor the -K option and not record key material by default.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
A network block specific background scan period can now be configured
for drivers that implement internal background scan mechanism for
roaming and BSS selection.
Signed-hostap: Bala Shanmugam <bkamatch@qca.qualcomm.com>
If the username part in the credential does not include a realm,
generate one automatically based on the configured realm information.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Make the connection change on Interworking network selection cases
clearer by forcing the previous association to be dropped before trying
to start a new one.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to use reassociation instead of association in a case
the previous connection was explicitly disconnected.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Implement wps_cancel for hostapd similarly to how it was already
supported in wpa_supplicant AP mode.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_pref_chan configuration parameter can now be used to set the
list of preferred channel for P2P GO Negotiation. This will be used
in the priority order if the peer does not support the channel we
are trying to use as the GO (configured operating channel or the
best 2.4 GHz/5 GHz channel) for the case where a forced channel is
not used.
p2p_pref_chan=<op class:channel>,...
For example:
p2p_pref_chan=81:1,81:2,81:3,81:4,81:5,81:6
This would configure 2.4 GHz channels 1-6 as the preferred ones with
channel 1 the most preferred option.
These configuration parameters can be set in wpa_supplicant.conf and
dynamically updated with "wpa_cli set <param> <value>".
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the ctrl_iface SCAN command to be used to run through a scan
to collect full scan results when sched_scan is in progress. sched_scan
will be re-started automatically after the full scan.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This patch adds a configuration in network block, ap_max_inactivity, for
station's inactivity period when in AP mode. The time period is
configured in seconds, by default 300 seconds.
Signed-hostap: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Use the normal group formation timeout during the provisioning phase to
avoid terminating this process too early due to group idle timeout.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the p2p_group_add command does not specify the operating channel,
make sure the operating channel set in the configuration file meets
the P2P requirements in the same way as is done with the frequency
specified as the command parameter.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Group properties are now accessible individually. The function to retrieve
the dictionary containing the group properties is removed in favor of the
individual functions. The group member properties are removed as well as
they erroneously retrieved the group properties via the old function.
Signed-hostap: Todd Previte <toddx.a.previte@intel.com>
Signed-hostap: Angie Chinchilla <angie.v.chinchilla@intel.com>
intended-for: hostap-1
After reallocation of the bss struct, current_bss wasn't updated and
could hold an invalid pointer (which might get dereferenced later).
Update current_bss if the pointer was changed.
Signed-hostap: Eliad Peller <eliad@wizery.com>
intended-for: hostap-1
If multiple station mode radios are bridged together on the same device,
it is possible for wpa_supplicant to receive EAPOL frames from the
bridge interface and then process them separately for each interface.
This can results in problems since multiple instances of supplicant side
could end up trying to process a single 4-way handshake. Avoid this
problem by filtering bridge interface EAPOL RX based on the desctination
MAC address. It should be noted that this works only when unicast
addresses are used (e.g., with WLAN) and not with the IEEE 802.1X EAPOL
group address (e.g., most wired networks).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use separate mnc_len parameter instead of expecting the imsi parameter
to be in special MCC|MNC|-|<MSIN> format to make this function more
generic.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows Interworking network selection to be used with EAP-TLS
(client certificate/private key based credential).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, this provisioning info was cleared using the P2P Interface
Address of the GO as the key. That did not always work in the case the
where we joined an already running group. This could result in the next
connection to that same GO skipping provision discovery. Fix this by
finding the peer entry based on its P2P Device Address instead of the
P2P Interface Address which may not always be set.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
Commit 6bf731e8ce broke handling of
EVENT_CHANNEL_LIST_CHANGED by introducing a cached copy of the driver
channel list that does not get updated even if driver changes its list.
Fix this by synchronizing the cacched wpa_s->hw.modes information
whenever EVENT_CHANNEL_LIST_CHANGED is processed. This fixes P2P channel
list updates based on regulatory domain hints that may trigger driver to
change its supported channel list.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
When wpa_supplicant disconnects, e.g., due to authentication timeout,
we need to go through the EVENT_DISASSOC/DEAUTH processing similarly
to the driver triggered cases to get correct events delivered to the
ctrl_iface. Fix this by calling wpa_supplicant_event() in these cases
and by filtering out the confusing CTRL-EVENT-DISCONNECTED event with
all zeros BSSID.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If a GO Negotiation peer is found, wpas_p2p_stop_find() stops the
negotiation and p2p_cancel can return success.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Since P2P GO cannot change the SSID after WPS provisioning step, we
can use the specific SSID for the scan for data connection. In addition,
mark this as p2p_probe to avoid unnecessary use of 802.11b rates.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Copy the SSID and frequency of the selected group into go_params in
join-a-running-group case so that the scan optimization can be used for
the provisioning step similarly to the case of group formation. This
uses a specific SSID and a single channel scan to avoid unnecessary
frames during the step.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Since the P2P client learns the SSID of the group during GO Negotiation,
use the specific SSID in the Probe Request frames during the
provisioning step. This helps in avoiding unnecessary Probe Response
frames from other P2P GOs or APs.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use Device Password ID in WSC IE of Probe Request and Probe Response
frames to advertise immediate availability of WPS credentials per P2P
specification sections 3.1.2.1.1 (Listen State), 3.1.2.1.2 (Scan Phase),
and 3.1.2.1.3 (Find Phase).
For now, the Device Password ID is set only for the case where we are
active GO Negotiation with a specific peer. In practice, this means that
the Probe Response frames during pending GO Negotiation (whenever in
Listen state) indicate availability of the credential.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This also disables WPS support if hidden SSID is enabled in AP mode.
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
New global configuration parameters pcsc_reader and pcsc_pin can now be
used to initialize PC/SC reader context at start of wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
These are from Android wpa_supplicant_8.git initial 0.8.X commit
8d520ff1dc2da35cdca849e982051b86468016d8 with some additional edits and
renaming of .config files to android.config.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This can be used to disable wpa_supplicant controlled roaming. It should
be noted that the WPA_DRIVER_FLAGS_BSS_SELECTION capability is the
preferred way for this and CONFIG_NO_ROAMING should be obsoleted once
drivers support the new NL80211_ATTR_ROAM_SUPPORT capability
advertisement.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Move disassociate and deauthenticate commands to ctrl_iface_ap.c, so
that they ares accessible for wpa_supplicant AP mode and wpa_cli (with
CONFIG_AP option enabled).
Signed-hostap: Jithu Jance <jithu@broadcom.com>
The org.freedesktop.DBus.Properties interface is now supported for peer
properties. Ensure that GetAll will work by having the IEs property
function return NULL data instead of a failure until it is implemented.
Signed-hostap: Reinette Chatre <reinette.chatre@intel.com>
intended-for: hostap-1
Commit 3f6e50ac28 made it possible to access
P2P peer properties using the org.freedesktop.DBus.Properties interface.
While maintaining the original intent of that patch we make two changes
to it here:
First, 3f6e50ac28 changed the type used to
represent the WPS vendor extension data from bytes to a string. In
addition to the type change the way in which the vendor extension data
was provided to the function creating the string was incorrect and would
not present the correct vendor extension data even in string format.
Revert the type change made in 3f6e50ac28
and present the WPS vendor extension data as an array of an array of
bytes as it was before.
Second, 3f6e50ac28 changes the secondary
device types representation from an array of an array of bytes to an
array of bytes. Revert that change to make secondary device types
accessible via an array of an array of bytes again.
Signed-hostap: Reinette Chatre <reinette.chatre@intel.com>
intended-for: hostap-1
If a wpabuf array is used to store basic typed data that we would like
to send over D-Bus then this utility will be of help when it places the
data in a variant with format aa? (array of an array of type ?, with ?
indicating any basic type).
Signed-hostap: Jayant Sane <jayant.sane@intel.com>
Signed-hostap: Angie Chinchilla <angie.v.chinchilla@intel.com>
intended-for: hostap-1
The wpas_p2p_group_idle_timeout was getting cancelled in the beginning
of wpas_p2p_group_delete(). However, in the case of P2P client role,
this function called wpa_supplicant_deauthenticate() next and that ended
up changing state to WPA_DISCONNECTED which resulted in
wpas_p2p_notif_disconnected() rescheduling the timeout. This left the
unexpected timeout behind after the group was removed. If another group
operation was started within P2P_MAX_CLIENT_IDLE (10) seconds, that
timeout could end up terminating the group while it was still being set
up.
Fix this by reordering wpas_p2p_group_delete() to cancel the group idle
timeout only after having called wpa_supplicant_deauthenticate(). The
group idle timeout is still rescheduled, but it gets removed immediately
afterwards when the actual group information is being cleared.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The previous elements need to be moved only if we are inserting the new
network in the middle of the list. While the memmove of zero bytes at
the end of the array does not cause real problems, some static analyzers
complain about this, so in addition to slightly optimized
implementation, this removes some analyzer warnings, too.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 9914c96feb moved sizeof(nai) to a
helper function and broke the determination of maximum buffer length.
Fix this by moving the sizeof() to the functions that define the buffer.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes WPA_INTERFACE_DISABLED more consistent in indicating that
wpa_supplicant cannot currently control the interface regardless of
whether the interface is disabled or completely removed.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
A list of disallowed frequencies for P2P channel list can now be
configured with P2P_SET disallow_freq. The frequencies (or frequency
pairs) are comma separated. For example:
wpa_cli p2p_set disallow_freq 2462,5000-6000
The allowed P2P channel list is constructed by removing explicitly
disallowed channels from the channel list received from the driver.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This was previously fixed for most cases in commit
ffad885837, but the check here for
drivers that implement SME/MLME was missed in that commit.
This removes the P2P IE from (Re)Association Request frame with
drivers that do not use wpa_supplicant SME implementation and are
P2P cabable when associating with a non-P2P AP (i.e., not a GO or
P2P WLAN manager AP).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
Previously, network block -based connection could have been used to
override ANQP-based selection. However, if no ANQP-based matches were
present, no connection was started. Fix this by trying to connect if
any enabled network block has a match in the BSS table.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows credentials to be set with a specific priority to allow
the automatic network selection behavior to be controlled with user
preferences. The priority values are configured to the network block
and BSS selection will select the network based on priorities from
both pre-configured network blocks and credentials.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
New wpa_cli commands list_creds, add_cred, remove_cred, and set_cred
can now be used to manage credentials similarly to the commands used
with network blocks.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This replaces the global home_* parameters with a list of credentials
that can be configured similarly to network blocks. For example:
cred={
realm="example.com"
username="user@example.com"
password="password"
ca_cert="/etc/wpa_supplicant/ca.pem"
domain="example.com"
}
cred={
imsi="310026-000000000"
milenage="90dca4eda45b53cf0f12d7c9c3bc6a89:cb9cccc4b9258e6dca4760379fb82581:000000000123"
}
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use Domain Name List (ANQP) and the new home_domain configuration
parameter to figure out whether a network is operated by the home
service provider and if so, prefer it over networks that would
require roaming.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows previously configured network profiles to be used so
that user can indicate preference of manually configured networks.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant can now be configured to filter out scan results based
on a BSSID filter. Space-separated set of allowed BSSIDs can be set
with wpa_cli set bssid_filter command. Filtering mechanism can be
disabled by setting this variable to an empty list. When set, only
the BSSes that have a matching entry in this list will be accepted
from scan results.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Extra parameter "no-connect" can now be added to the ENABLE_NETWORK
ctrl_iface command to avoid automatic connection to the enabled
network.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"wpa_cli set radio_disabled 1/0" can be used to disable/enable
radio to simulate out-of-radio-range condition in a testbed
device.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Normal scan is more reliable and faster for WPS operations and since
these are for short periods of time, the benefit of trying to use
sched_scan would be limited. This can fix WPS connectivity issues
with some drivers.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
In IBSS RSN cfg80211/mac80211 now waits for userspace to authorize new
stations. This patch makes wpa_supplicant notify the driver when a
station can be considered authorized.
Signed-hostap: Antonio Quartulli <ordex@autistici.org>
When using more than around 200 virtual stations, we start hitting the
max number of file descriptors supported by select(). This patch adds
support for poll(), which has no hard upper limit.
Signed-hostap: Ben Greear <greearb@candelatech.com>
Commit 3c85f144ce fixed issues with P2P
Action frame TX after disconnection by clearing wpa_s->assoc_freq.
This resulted in a regression to the post-WPS scan optimization that
used wpa_s->assoc_freq to enable fast single-channel scan. Fix this by
copying wpa_s->assoc_freq to a local variable before calling
wpa_supplicant_deauthenticate() that ends up calling
wpa_supplicant_mark_disassoc() which will clear assoc_freq.
Reported-by: Angie Chinchilla <angie.v.chinchilla@intel.com>
intended-for: hostap-1
Signed-hostap: Jouni Malinen <j@w1.fi>
Remove the GPL notification text from files that were initially
contributed by Atheros Communications or Qualcomm Atheros.
Signed-hostap: Jouni Malinen <j@w1.fi>
Simplify licensing terms for hostap.git by selecting the BSD license
alternative for any future distribution. This drops the GPL v2
alternative from distribution terms and from contribution requirements.
The BSD license alternative that has been used in hostap.git (the one
with advertisement clause removed) is compatible with GPL and as such
the software in hostap.git can still be used with GPL projects. In
addition, any new contribution to hostap.git is expected to be licensed
under the BSD terms that allow the changes to be merged into older
hostap repositories that still include the GPL v2 alternative.
Signed-hostap: Jouni Malinen <j@w1.fi>
Since there is the method org.freedesktop.DBus.Properties.GetAll that
returns all properties from a specific interface, it makes more sense to
separate the properties to make it possible to get only a single
property using the method org.freedesktop.DBus.Properties.Get as well.
Signed-hostap: Flávio Ceolin <flavio.ceolin@profusion.mobi>
This fixes a build regression from commit
cd2f4ddfb9 by moving
wpa_supplicant_assoc_update_ie() outside the no-scan-processing ifdef
block.
Signed-hostap: Jouni Malinen <j@w1.fi>
The BSS ctrl_iface command can sow the age of a BSS table entry to
make it easier for external programs to figure out whether an entry
is still current depending on the use case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"BSS p2p_dev_addr=<P2P Device Address>" can now be used to fetch a
specific BSS entry based on the P2P Device Address of the GO to avoid
having to iterate through the full BSS table when an external program
needs to figure out whether a specific peer is currently operating as
a GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When a GO is operating a persistent group and invites a peer that has
been a P2P client in that persistent group, the Invitation Type in the
Invitation Request frame can be set to 1 to indicate that this is a
reinvocation of a persistent group. Do this based on the maintained
list of P2P clients that have been provided the credentials to this
group.
Signed-hostap: Jouni Malinen <j@w1.fi>
Even though the Provision Discovery Response frame from PD-before-join
does not really provide any additional information, it can be better to
wait for it before starting the join operation. This adds a minimal
extra latency in the most common case and cleans up the sequence of
driver operations and debug log by avoiding potential processing of the
Provision Discovery Response while already running a scan for the actual
connection.
If transmission of Provision Discovery Request fails, join operation is
started without the additional wait. In addition, a new timeout is used
to start the join if Provision Discovery Response is lost for any
reason.
Signed-hostap: Jouni Malinen <j@w1.fi>
Provision Discovery is used as a notification to the GO in the case we
are about join a running group. In such case, there is not much point in
indicating the provision discovery response events to external programs
especially when the PIN-to-be-displayed was different from the one
returned for the p2p_connect command. Skip this confusing event
completely for join-a-running-group case.
Signed-hostap: Jouni Malinen <j@w1.fi>
These changes account for situations where the CQM threshold
might be approximately the same as the currently received signal,
and thus CQM events are triggered often due to measurement
error/small fluctuations. This results in scanning occurring
too frequently.
Firstly, inhibit the immediate scan when the short-scan count
is at the maximum. This keeps bursts of CQM toggling from
causing a torrent of back-to-back scans. This does not inhibit
immediate scans if the CQM triggers a second time (if the signal
falls lower past the hysteresis). This reduces the scan rate in
the worst case (fast-rate toggling high/low CQM events) to the
short scan interval.
Secondly, change the behavior of the short scan count so it acts like
a "leaky bucket". As we perform short-scans, the bucket fills until
it reaches a maximal short-scan count, at which we back-off and
revert to a long scan interval. The short scan count decreases by
one (emptying the bucket) every time we complete a long scan interval
without a low-RSSI CQM event.
This reduces the impact of medium-rate toggling of high/low CQM
events, reducing the number of short-interval scans that occur before
returning to a long-interval if the system was recently doing
short scans.
Driver global init was considered a hard failure. Thus if, for example,
you used the Broadcom STA driver and didn't have nl80211 or cfg80211
loaded into the kernel, and specified a driver value of "nl80211,wext",
the nl80211 driver's global init would fail with the following message:
nl80211: 'nl80211' generic netlink not found
Failed to initialize driver 'nl80211'
but since global init was a hard failure, creating the supplicant
interface would fail and the WEXT driver would not be tried.
Give other drivers a chance instead.
Signed-hostap: Dan Williams <dcbw@redhat.com>
intended-for: hostap-1
The setter function uses the same hostapd_data structure as the getter
which causes it to crash if called on a P2P client. To overcome this
issue, the role is checked to ensure it is called on a group owner and
the pointer is examined for validity. The function will return an error
if called on a non-GO system.
Signed-hostap: Todd Previte <toddx.a.previte@intel.com>
Signed-hostap: Angie Chinchilla <angie.v.chinchilla@intel.com>
intended-for: hostap-1
When using DBus to get group properties, a segmentation fault is
generated on P2P clients due to a NULL pointer for the ap_iface struct.
The current implementation only returns vendor extensions when called on
a P2P group owner.
The code now checks the P2P role which allows for role-specific
information to be provided. This also fixes the crash issue by only
looking for the correct structures based on the current P2P role.
Signed-hostap: Todd Previte <toddx.a.previte@intel.com>
Signed-hostap: Angie Chinchilla <angie.v.chinchilla@intel.com>
intended-for: hostap-1
When looking for PMKSA cache entries to use with a new association, only
accept entries created with the same network block that was used to
create the cache entry.
Signed-hostap: Jouni Malinen <j@w1.fi>
The disconnection command results in disassociation and deauthentication
events which were previously processed during the scan in case of
select_network command being used while associated with another network.
While this works in most cases, it can result in confusing event
messages in ctrl_iface and debug log. Avoid this by using a short delay
between the disconnection and scan request to allow the disconnection
events to be processed prior to starting the new scan.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
While the exponential increase in the lockout period provides an
efficient mitigation mechanism against brute force attacks, this
additional trigger to enter indefinite lockout period (cleared by
restarting hostapd) will limit attacks even further by giving maximum of
10 attempts (without authorized user action) even in a very long term
attack.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows HT capabilities overrides on kernels that
support these features.
MCS Rates can be disabled to force to slower speeds when using HT.
Rates cannot be forced higher.
HT can be disabled, forcing an 802.11a/b/g/n station to act like
an 802.11a/b/g station.
HT40 can be disabled.
MAX A-MSDU can be disabled.
A-MPDU Factor and A-MPDU Density can be modified.
Please note that these are suggestions to the kernel. Only mac80211
drivers will work at all. The A-MPDU Factor can only be decreased and
the A-MPDU Density can only be increased currently.
Signed-hostap: Ben Greear <greearb@candelatech.com>
Now that CTRL-EVENT-TERMINATING even is sent at the end of interface
removal in case wpa_supplicant process is going to terminate, there
is no need for this duplicated event in the signal handler.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows TERMINATING ctrl_iface event to be sent at the end of the
deinit sequence to avoid race conditions with new operations that this
event may trigger while wpa_supplicant would still be running through
the deinitialization path.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This avoids issues with some external program starting to use the
interface based on the interface removal event before wpa_supplicant
has completed deinitialization of the driver interface.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This will be needed to be able to move ctrl_iface TERMINATING event to
the end of interface removal.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
current_bss and pending_bssid weren't cleaned up so BSS
kept appearing in the scan results even when it was actually gone.
Use wpa_supplicant_mark_disassoc() to cleanup the wpa_s context
instead of just dropping wpa_state back to DISCONNECTED.
Reported-by: Vishal Mahaveer <vishalm@ti.com>
Signed-hostap: Eyal Shapira <eyal@wizery.com>
For drivers limited to scan a single SSID at a time, this prevents
waiting too long for a wildcard scan in case there are several
scan_ssid networks in the configuration.
Signed-hostap: Eyal Shapira <eyal@wizery.com>
This changes the install target such that parent directories of
installed paths area created and each path is only installed
on a dependency basis.
Signed-off-by: Grant Erickson <marathon96@gmail.com>
This is a useful function that simplifies some code and can eventually
be used somewhere else in future.
Signed-hostap: Antonio Quartulli <ordex@autistici.org>
These properties did not work on big endian PowerPC (always 100% for
Signal and 0 for Frequency) due to endianness problem (u32 to u16 data
loss).
Signed-off-by: Sylvestre Gallon <ccna.syl@gmail.com>
Perforce does not like @ in the file name and since these template files
do not really need to have that in the name, make the files in
repository friendlier to Perforce. The generated *.service file will
maintain their old names.
Signed-hostap: Jouni Malinen <j@w1.fi>
When the "bssid=" option is set for an IBSS network and ap_scan = 2,
ask the driver to fix this BSSID, if possible.
Previously, any "bssid=" option were ignored in IBSS mode when ap_scan=2.
Signed-hostap: Nicolas Cavallari <cavallar@lri.fr>
Provide a means over DBus to set the conf->fast_reauth
property, which controls whether TLS session resumption
should be attempted for EAP-TLS 802.1X networks.
Signed-off-by: Paul Stewart <pstew@chromium.org>
wpas_wps_in_use() was forcing WPS to be enabled unconditionally if P2P
support was included in the build. This is not really the correct
behavior for the case when P2P has been disabled at runtime. Change the
code here to verify runtime configuration of P2P before forcing WPS to
be enabled. This allows WSC IE to be left out from Probe Request frames
when scanning for APs without P2P or WPS being in use.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Even though we may not update P2P peer entry while connected to the
peer as a P2P client, we should not be expiring a P2P peer entry while
that peer is the GO in a group where we are connected as a P2P client.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When a P2P group is removed, we better not leave possibly started
sched_scan running. This could happen when a separate group interface
was not used.
In addition, it looks safer to explicitly stop sched_scan before
starting P2P Listen or Find operations to make sure the offloaded
scanning is not running when doing similar P2P operations.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This patch fixes an issue with roaming for drivers that set
WPA_DRIVER_FLAGS_BSS_SELECTION (currently ath6kl). On moving to an AP
with a different BSSID, an EVENT_ASSOC is received and the subsequent
4-way handshake may fail because of a mismatch between the RSN IE in
message 3/4 and in Beacon/Probe Response. This happens only when the APs
use different RSN IE contents and ap_scan is set to 1, since
wpa_supplicant fails to update its cached IEs.
Initial association may fail, too, in case of multiple APs with
the same SSID, since BSSID selection is done by the driver and again
a mismatch could be seen.
Fix these two issues by clearing and updating the cached IEs on
receiving an Association event from the driver. Also, retrieve the
scan results when the new BSS information is not present locally.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
dev_id=<P2P Device Addr> can now be specified as an argument to
p2p_find to request P2P find for a specific P2P device.
Signed-hostap: Jouni Malinen <j@w1.fi>
The deauthentication and disassociation events from nl80211 were being
processed identically regardless of whether the frame was generated by
the local STA or the AP. This resulted in fast reconnection mechanism
getting triggered even in the case where the disconnection was detected
locally (e.g., due to beacon loss) while this was supposed to happen
only in the case where the AP is sending an explicit Deauthentication
or Disassociation frame with a specific reason code.
Fix this by adding a new deauth/disassoc event variable to indicate
whether the event was generated locally.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit e9c3c1afed added a new D-Bus
method and that was enough to push the Introspect XML buffer over
the previously allocated 8000 bytes. Increase the buffer size to
make enough room for P2P interface. In addition, add a debug
message to indicate if an XML segment does not fit into the buffer
to make this types of failures somewhat easier to catch.
Signed-hostap: Jouni Malinen <j@w1.fi>
The authentication timeout could be triggered after the connection has
already been known to have failed. The event at that point can be
confusing, so better cancel the timeout when processing connection
failure.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the BSSID of the AP is specified in the WPS command, the target
AP is likely already in the BSS table and its operating channel is
known. Use this information to speed up connection by only scanning
the known channel.
Signed-hostap: Jouni Malinen <j@w1.fi>
The 'network.target' is special (per systemd.special(7)), and is to be
brought up indirectly when network is actually configured (i.e. through
DHCP or static address settings).
Irrelevant of that, all services should be always installed in
multi-user.target.
[Bug 427]
This fixes issues with drivers that do not handle concurrent
remain-on-channel and scan operations in a case where Provision
Discovery Response frame is not received to stop the Action frame
handshake.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the freq parameter is specified and we are already running legacy STA
on a different frequency with a driver that does not support
multi-channel concurrency, reject p2p_group_add. Same code already
exists in the path of P2P connection with go negotiation but is missing
for autonomous GO.
Signed-hostap: Neeraj Garg <neerajkg@broadcom.com>
Add a new persistent group network block field, p2p_client_list, to
maintain a list of P2P Clients that have connected to a persistent
group. This allows GO of a persistent group to figure out more easily
whether re-invocation of a persistent group can be used with a specific
peer device.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add "persistent=<network id>" line to P2P_PEER ctrl_iface data
if a persistent group credentials are available for this peer.
This makes it easier for external programs to figure out when
a persistent group could be re-invoked with this peer.
For now, this information is only available on the P2P client,
but similar information can be added for GO once a list of P2P
clients is maintained with the persistent group data.
Signed-hostap: Jouni Malinen <j@w1.fi>
The P2P module provides access to public peer data in struct
p2p_peer_info. Use this to build the P2P_PEER information in
ctrl_iface.c instead of providing such text format data from the P2P
module.
The internal data that was previously built in p2p_get_peer_info() as
part of the text format peer data is now available through a separate
p2p_get_peer_info_txt() function. This is still included in P2P_PEER
output to maintain backwards compatibility with external programs that
could have started to use this. However, it should be noted that this
data is not really supposed to be used for anything else apart from
debugging purposes and its format is subject to change.
Signed-hostap: Jouni Malinen <j@w1.fi>
p2p_get_peer_info() was used in multiple places just to check whether a
specific peer is known. This was not the designed use for the function,
so introduce a simpler function for that purpose to make it obvious that
the p2p_get_peer_info() function is actually used only in ctrl_iface.c.
Signed-hostap: Jouni Malinen <j@w1.fi>
The internal sched_scanning state needs to be cleared on this event
even if the events happen to get ordered in a way that the interface
gets disabled just prior to EVENT_SCHED_SCAN_STOPPED event.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the driver was associated in station mode just before the AP mode was
started, the station mode disassociation event may end up getting
delivered to wpa_supplicant only after the AP mode has been started.
This can result in unexpected attempt to reassociate back to the network
that was previously used in station mode. Avoid this by ignoring the
disassociation event.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The active station connection triggered wpa_supplicant AP mode startup
to try to update Beacon IEs before the AP mode was properly initialized
and that resulted in NULL pointer dereference in driver_nl80211.c. Fix
this by skipping the IE update before the AP mode is initialized.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The p2p_group_idle configuration parameter is much more useful for
GO role, so use a separate hardcoded value of 10 seconds in P2P
client role. In practice, this means that the P2P client role will
automatically tear down the group when the GO tears down the group.
The 10 second timeout is enough to recover from temporary disconnections
without unnecessary tearing down the group if the GO is still present
and allows the client to connect.
Signed-hostap: Jouni Malinen <j@w1.fi>
When P2P client is processing a disconnection event, make sure the P2P
idle timeout does not get increased, i.e., set a new timeout only if no
timeout is in use. wpa_state changes between DISCONNECTED and SCANNING
can generate multiple calls to wpas_p2p_notif_disconnect() and
previously this was enough to force the idle timeout never hit in
practice when in P2P client role.
Signed-hostap: Jouni Malinen <j@w1.fi>
This event can be very frequent in AP mode when Beacon frames from
neighboring BSSes are delivered to user space. Drop the debug
message priority from DEBUG to EXCESSIVE for Beacon frames.
Signed-hostap: Jouni Malinen <j@w1.fi>
The Provision Discovery Request needs to be sent on the operating
channel of the GO and as such, the frequency from the BSS table
(scan results) need to override the frequency in the P2P peer
table that could be based on the Listen channel of the GO.
Signed-hostap: Jouni Malinen <j@w1.fi>
When in AP mode, wpa_supplicant is now enabling WPS (only Internal
Registrar). WPS.Start() call can be used to initiate WPS negotiation
similarly to how this is done in station mode.
This was done to ctrl_iface by Jouni Malinen on April 21, 2009 (commit
3ec97afe57)
Signed-hostap: Gustavo Sverzut Barbieri <barbieri@profusion.mobi>
The GO negotiation response is very cryptic at the moment. For a success
message we only know on which interface the negotiation succeeded, not
which peer. For a failure we know the interface also and a status code
(number).
It will be very useful for clients to know upon receipt of such a message
which peer the negotiation occurred with.
Now that the peer information is available and the API is changed
already, the function composing the D-Bus message might as well include
all GO negotiation information. This is done with a dict to make things
easier on clients if this result information changes down the line.
Signed-hostap: Reinette Chatre <reinette.chatre@intel.com>
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Need to remove ROAM command processing since the needed functionality
for it gets removed with CONFIG_NO_SCAN_PROCESSING=y.
Signed-hostap: Jouni Malinen <j@w1.fi>
The whole wpa_supplicant_ctrl_iface_ctrl_rsp_handle() function operates
on the ssid->eap field which exists only if IEEE8021X_EAPOL has been
defined. Therefore the whole function body needs to be enclosed within
an #ifdef/endif block.
Signed-hostap: Antonio Quartulli <ordex@autistici.org>
Antonio reported that RSN IBSS failed to work.
We traced it down to a GTK failure, and he then
bisected it to commit bdffdc5ddb:
"AP: Reorder WPA/Beacon initialization".
The reason this commit broke it is that the state
machine's GInit variable is never set to false as
wpa_init_keys() never gets called, and thus new
keys are generated every time the state machine
executes.
Fix this by calling wpa_init_keys() when the new
group has been initialised.
Reported-by: Antonio Quartulli <ordex@autistici.org>
Tested-by: Antonio Quartulli <ordex@autistici.org>
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Previously, the WPS scans could have been done in associated state if we
happened to be associated when the request to use WPS was received. This
can slow down scanning and end up in unexpected state if no WPS
association is tried. Avoid these issues by disconnecting when WPS
search is started.
Signed-hostap: Jouni Malinen <j@w1.fi>
Convert core wpa_supplicant code to use u64 instead of void * for the
P2P service discovery reference. Use uintptr_t in type casts in
p2p_supplicant.c to handle the conversion without warnings.
Note: This needs to be revisited for 128-bit CPU where sizeof(void *)
could be larger than sizeof(u64).
Signed-hostap: Jouni Malinen <j@w1.fi>
Some debug messages used incorrect name for Provision Discovery.
Replace "Provisioning Discovery" with "Provision Discovery".
Signed-hostap: Jouni Malinen <j@w1.fi>
WPS overlap detection can detect false overlap if a P2P peer
changes UUID while authentication is ongoing. Changing UUID
is of course wrong but this is what some popular devices do
so we need to work around it in order to keep compatibility
with these devices. There already is a mechanism in WPS
registrar to skip overlap detection if P2P addresses of two
sessions match but it wasn't really triggered because the
address wasn't filled in in the caller function.
Let's fill in this address and also clean up WPS PBC sessions
on WSC process completion if UUID was changed.
Signed-hostap: Vitaly Wool<vitalywool@gmail.com>
If a P2P group network block is removed for any reason (e.g., wps_cancel
command) while the interface is in group formation, remove the group
formation timeout and indicate failure immediately. Previously, this
type of operations could end up leaving the timeout running and result
in somewhat unexpected group formation failure events later.
Signed-hostap: Jouni Malinen <j@w1.fi>
If Provision Discovery Request is sent for GO role (i.e., P2P Group ID
attribute is included), add the group interface name to the control
interface event on the GO. This makes it easier to figure out which
ctrl_iface needs to be used for wps_pbc/wps_pin command to authorize
the joining P2P client.
Signed-hostap: Jouni Malinen <j@w1.fi>
