Using average signal strength from the driver and hardcoded noise floor
does not look like an ideal design since there can be significant
differences in the driver-reported noise floor values. Furthermore, even
though the current noise floor is a snapshot from the driver, it is
common for drivers to use a noise floor value from a longer calibration
step and that should not prevent the driver provided value from being
used. This makes the comparisons of the signal strengths between the
current AP (signal_poll) and other APs (scan) more accurate.
As an example, test runs in home environment showed 5 dB difference
between the driver reported noise floor and the hardcoded value and this
could result in significant differences in estimated throughput
calculation.
Signed-off-by: Jouni Malinen <j@w1.fi>
Some drivers (e.g. Marvell WiFi) don't report avg_beacon_signal, but
it's still useful to poll for the signal again when a roaming decision
needs to be made. Use si.avg_signal when si.avg_beacon_signal is not
available.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
We saw that on certain platforms in certain places we keep switching
between two APs and eventually get the same RSSI. Debugging showed that
we have a very big difference between the two antennas.
Ant A can hear AP A very well (-60) but AP B very bad (-80)
Ant B can hear AP B very well (-60) but AP A very bad (-80)
When the device associates to AP A, it'll learn to use Ant A. If the
device uses one single antenna to receive the scan results, it may hear
the AP it is currently associated to on the second antenna and get bad
results. Because of that, the wpa_supplicant will roam to the other AP
and the same scenario will repeat itself:
Association to AP A (Ant A reports -60).
Scan on Ant A: AP A: -60, AP B: -80
Scan on Ant B: AP A: -80, AP A: -60 ==> ROAM.
Association to AP B (Ant B reports -60)
Scan on Ant A: AP A: -60, AP B: -80 ==> ROAM
Etc...
Improve this by querying the signal level of the current AP using
drv_signal_poll() instead of relying on the signal level that we get
from the scan results. Also update the throughput estimate based on the
likely more accurate values for the current association.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This is a step towards allowing these values to be determined based on
signal poll instead of scan results.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Field wpa_s->sme.ht_sec_chan keeps secondary channel for the 40 MHz
band. This field is used to prepare a list of channels for the STA OBSS
scan. Initially, the secondary channel is set to HT_SEC_CHAN_UNKNOWN.
Later on, in function wpa_obss_scan_freq_list() it is obtained from the
current BSS HT operation IE. However, the secondary channel information
is not updated after channel switch, which may lead to an incorrect list
of channels prepared for the STA OBSS scan.
Update ht_sec_chan according to the channel switch event data to fix
this.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
In the previous implementation connected STA performs OBSS scan
according to requests from its 20/40 MHz AP. However STA checks only 40
MHz intolerance subfield from HT Capabilities element in scan results.
Meanwhile, as per IEEE Std 802.11-2016, 11.16.12, STA should check
overlapping BSSs as well.
Note that all the required code to check overlapping BSSs did already
exist for AP mode since AP does those checks properly before operating
as 20/40 MHz BSS in the 2.4 GHz band. Use that existing code by replace
existing 40 MHz intolerance check in sme_proc_obss_scan() with the new
shared helper function check_bss_coex_40mhz().
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
When a PTK rekey fails it can't be caused by a PSK mismatch. Report a
possible PSK mismatch only during the initial 4-way handshake to avoid
incorrect reports.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
The previous implementation missed the case where EAPOL-Key frame may be
reported as having been received before the association event is
processed. This would have resulted in not using the RSNXE override for
EAPOL-Key msg 2/4 when the pending EAPOL-Key frame gets processed
immediately after processing the association event. Fix this by moving
the override case to be handled before that.
Fixes: 1325655397 ("SAE H2E: RSNXE override for testing purposes")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
"SET rsnxe_override_{assoc,eapol} <hexdump>" can now be used to override
RSNXE in (Re)Association Request frames and EAPOL-Key msg 2/4 for
testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
"SET ignore_sae_h2e_only 1" can now be used to configurate
wpa_supplicant to a test mode where it ignores AP's H2E-required
advertisement and try to connect with hunt-and-pecking loop instead.
This is used only for testing AP behavior with unexpected STA behavior.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
wpa_key_mgmt_wpa_psk() includes SAE AKMs. However, with SAE, there is no
way of reaching 4-way handshake without the password having already been
verified as part of SAE authentication. As such, a failure to complete
4-way handshake with SAE cannot indicate that the used password was
incorrect.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add the new RSNXE into (Re)Association Request frames and EAPOL-Key msg
2/4 when using SAE with hash-to-element mechanism enabled. This allows
the AP to verify that there was no downgrade attack when both PWE
derivation mechanisms are enabled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If the AP advertises RSN Extension element, it has to be advertised
consistently in the unprotected (Beacon and Probe Response) and
protected (EAPOL-Key msg 3/4) frames. Verify that this is the case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
After roaming to an AP, update disable_mbo_oce flag based on the current
BSS capabilities. This flag is used to check whether STA should support
MBO/OCE features and process BTM request received from the current
connected AP.
When a STA roams from a WPA2 MBO/OCE AP with PMF enabled to a
misbehaving WPA2 MBO/OCE AP without PMF, or if the driver chooses a BSS
in which PMF is not enabled for the initial connection, BTM requests
from such APs should not be processed by STA.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The MBO and OCE specification require the station to mandate use of PMF
when connecting to an MBO/OCE AP that uses WPA2. The earlier
implementation prevented such misbehaving APs from being selected for
connection completely. This looks like the safest approach to take, but
unfortunately, there are deployed APs that are not compliant with the
MBO/OCE requirements and this strict interpretation of the station
requirements results in interoperability issues by preventing the
association completely.
Relax the approach by allowing noncompliant MBO/OCE APs to be selected
for RSN connection without PMF to avoid the main impact of this
interoperability issue. However, disable MBO/OCE functionality when PMF
cannot be negotiated to try to be as compliant as practical with the
MBO/OCE tech spec requirements (i.e., stop being an MBO/OCE STA for the
duration of such workaround association). Also disable support for BTM
in this workaround state since MBO would expect all BTM frames to be
protected.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Hardcode this to be defined and remove the separate build options for
PMF since this functionality is needed with large number of newer
protocol extensions and is also something that should be enabled in all
WPA2/WPA3 networks.
Signed-off-by: Jouni Malinen <j@w1.fi>
An OCE AP with WPA2 enabled shall require PMF negotiation when
associating with an OCE STA. An OCE STA-CFON may negotiate PMF with a
STA when it is operating as an AP. Don't select an OCE AP for connection
if PMF is not enabled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The conditions for the eapol_sm_notify_eap_success(FALSE) calls did not
cover the case where eapol_sm_notify_eap_success(TRUE) had been called
based on offloaded 4-way handshake and driver notification of
authorization in wpa_supplicant_event_port_authorized(). This could
result in eapSuccess and altSuccess state machine variables being left
TRUE when roaming to another BSS and that results in EAP failure if the
following roaming case does not get fully authorized through the driver
offload.
Fix this by clearing eapSuccess/altSuccess when processing a new
association (including roaming) event and also when disconnecting from
the network.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previously, these default scan IEs were set only when parameter values
changed and during the interface initialization, which can get lost in
the driver on an interface restart. Hence, also set these IEs on an
interface restart notification even when there has been no change in the
values since the last update to the driver.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The ssid->mode is from type enum wpas_mode and all its constants start
with WPAS_MODE_*. Still some of the code sections used the
IEEE80211_MODE_* defines instead of WPAS_MODE_*.
This should have no impact on the actual code because the constants for
INFRA, IBSS, AP and MESH had the same values.
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
If an AP rejects association due to low RSSI, then RSSI of the BSS from
which association reject is received shall be used for calculating RSSI
threshold at which STA can try connecting back to that BSS later. In
case of SME offload, the current_bss might not have been set before
receiving association completion, so fetch the BSS entry based on the
BSSID provided in the driver event.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This makes it easier to upper layer components to manage operating
channels in cases where the same radio is shared for both station and AP
mode virtual interfaces.
Signed-off-by: Omer Dagan <omer.dagan@tandemg.com>
Logs involving IEEE 802.11 Reason Codes output the Reason Code value,
but do not provide any explanation of what the value means. This change
provides a terse explanation of each Reason Code using the latter part
of the reason code #define names.
Signed-off-by: Alex Khouderchah <akhouderchah@chromium.org>
When FILS authentication is used with ERP, no EAPOL frames are expected
after association. However, for drivers that set the
WPA_DRIVER_FLAGS_4WAY_HANDSHAKE_8021X capability flag, the EAP state
machine was not configured correctly and was waiting for EAPOL frames,
which leads to disconnection.
Fix this by reordering the if branches to set the EAPOL/EAP state
machines to success when FILS authentication was already completed.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Use Diffie-Hellman key exchange to derivate additional material for
PMK-to-PTK derivation to get PFS. The Diffie-Hellman Parameter element
(defined in OWE RFC 8110) is used in association frames to exchange the
DH public keys. For backwards compatibility, ignore missing
request/response DH parameter and fall back to no PFS in such cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Some driver interfaces (e.g., wext) might not include the
data->scan_info information and data could be NULL here. Do not try to
call the RRM handler in this case since that would dereference the NULL
pointer when determining where scan_info is located and could
potentially result in trying to read from unexpected location if RRM is
enabled with a driver interface that does not support it.
events.c:1907:59: runtime error: member access within null pointer of type 'union wpa_event_data'
Signed-off-by: Jouni Malinen <j@w1.fi>
According to IEEE Std 802.11-2016, 9.4.2.25 when fields of an RSNE are
not included, the default values are used. The cipher suite defaults
were hardcoded to CCMP in the previous implementation, but the default
is actually different for DMG: GCMP (per 9.4.2.25.2).
It is not possible to find out from the RSNE if the network is non-DMG
or DMG, so callers of wpa_parse_wpa_ie_rsn() need to handle this case
based on context, which can be different for each caller.
In order to fix this issue, add flags to the wpa_ie_data indicating
whether pairwise/group ciphers were included in the RSNE. Callers can
check these flags and fill in the appropriate ciphers. The
wpa_parse_wpa_ie_rsn() function still initializes the ciphers to CCMP by
default so existing callers will not break. This change also fixes some
callers which need to handle the DMG network case.
Signed-off-by: Lior David <liord@codeaurora.org>
The Wi-Fi Alliance Multi-AP Specification v1.0 allows onboarding of a
backhaul STA through WPS. To enable this, the backhaul STA needs to add
a Multi-AP IE to the WFA vendor extension element in the WSC M1 message
that indicates it supports the Multi-AP backhaul STA role. The Registrar
(if it support Multi-AP onboarding) will respond to that with a WSC M8
message that also contains the Multi-AP IE, and that contains the
credentials for the backhaul SSID (which may be different from the SSID
on which WPS is performed).
Introduce a new parameter to wpas_wps_start_pbc() and allow it to be
set via control interface's new multi_ap=1 parameter of WPS_PBC call.
multi_ap_backhaul_sta is set to 1 in the automatically created SSID.
Thus, if the AP does not support Multi-AP, association will fail and
WPS will be terminated.
Only wps_pbc is supported.
This commit adds the multi_ap argument only to the control socket
interface, not to the D-Bus interface.
Since WPS associates with the fronthaul BSS instead of the backhaul BSS,
we should not drop association if the AP announces fronthaul-only BSS.
Still, we should only do that in the specific case of WPS. Therefore,
add a check to multi_ap_process_assoc_resp() to allow association with a
fronthaul-only BSS if and only if key_mgmt contains WPS.
Signed-off-by: Davina Lu <ylu@quantenna.com>
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Cc: Marianna Carrera <marianna.carrera.so@quantenna.com>
This adds a wifi_generation=4/5/6 line to the STATUS output if the
driver reports (Re)Association Request frame and (Re)Association
Response frame information elements in the association or connection
event. Only the generations 4 (HT = 802.11n), 5 (VHT = 802.11ac), and 6
(HE = 802.11ax) are reported.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Allow drivers to indicate support for offloading 4-way handshake for
either IEEE 802.1X (WPA2-Enterprise; EAP) and/or WPA/WPA2-PSK
(WPA2-Personal) by splitting the WPA_DRIVER_FLAGS_4WAY_HANDSHAKE flag
into two separate flags.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Once mesh starts supporting DFS channels, it has to handle DFS related
events from drivers, hence add mesh interface to the check list.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
wpa_supplicant currently logs CTRL-EVENT-AUTH-FAILED errors when
authentication fails, but doesn't expose any property to the D-Bus
interface related to this.
This change adds the "AuthStatusCode" property to the interface, which
contains the IEEE 802.11 status code of the last authentication.
Signed-off-by: Alex Khouderchah <akhouderchah@chromium.org>
Add new Interface properties "RoamTime", "RoamComplete", and
"SessionLength". "RoamTime" carries the roam time of the most recent
roam in milliseconds. "RoamComplete" carries True or False corresponding
to the success status of the most recent roam. "SessionLength" carries
the number of milliseconds corresponding to how long the connection to
the last AP was before a roam or disconnect happened.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
An AP might refuse to connect a STA if it has a low RSSI. In such case,
the AP informs the STA with the desired RSSI delta and a retry timeout.
Any subsequent association attempt with that AP (BSS) should be avoided,
unless the RSSI level improved by the desired delta or the timeout has
expired.
Defined in Wi-Fi Alliance Optimized Connectivity Experience technical
specification v1.0, section 3.14 (RSSI-based association rejection
information).
Signed-off-by: Beni Lev <beni.lev@intel.com>
Try to make sure the driver channel list state is synchronized with
wpa_supplicant whenever explicitly clearing state (e.g., between hwsim
test cases).
Signed-off-by: Jouni Malinen <j@w1.fi>
Advertise vendor specific Multi-AP IE in (Re)Association Request frames
and process Multi-AP IE from (Re)Association Response frames if the user
enables Multi-AP fuctionality. If the (Re)Association Response frame
does not contain the Multi-AP IE, disassociate.
This adds a new configuration parameter 'multi_ap_backhaul_sta' to
enable/disable Multi-AP functionality.
Enable 4-address mode after association (if the Association Response
frame contains the Multi-AP IE). Also enable the bridge in that case.
This is necessary because wpa_supplicant only enables the bridge in
wpa_drv_if_add(), which only gets called when an interface is added
through the control interface, not when it is configured from the
command line.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
After the network changed to a new channel, perform an SA Query with the
AP after a random delay if OCV was negotiated for the association. This
is used to confirm that we are still operating on the real operating
channel of the network. This commit is adding only the station side
functionality for this, i.e., the AP behavior is not changed to
disconnect stations with OCV that do not go through SA Query.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
Do not change the OWE group if association is rejected for any other
reason than WLAN_STATUS_FINITE_CYCLIC_GROUP_NOT_SUPPORTED to avoid
unnecessary latency in cases where the APs reject association, e.g., for
load balancing reasons.
Signed-off-by: Ashok Kumar <aponnaia@codeaurora.org>
Add support for negotiating WNM Collocated Interference Reporting. This
allows hostapd to request associated STAs to report their collocated
interference information and wpa_supplicant to process such request and
reporting. The actual values (Collocated Interference Report Elements)
are out of scope of hostapd and wpa_supplicant, i.e., external
components are expected to generated and process these.
For hostapd/AP, this mechanism is enabled by setting
coloc_intf_reporting=1 in configuration. STAs are requested to perform
reporting with "COLOC_INTF_REQ <addr> <Automatic Report Enabled> <Report
Timeout>" control interface command. The received reports are indicated
as control interface events "COLOC-INTF-REPORT <addr> <dialog token>
<hexdump of report elements>".
For wpa_supplicant/STA, this mechanism is enabled by setting
coloc_intf_reporting=1 in configuration and setting Collocated
Interference Report Elements as a hexdump with "SET coloc_intf_elems
<hexdump>" control interface command. The hexdump can contain one or
more Collocated Interference Report Elements (each including the
information element header). For additional testing purposes, received
requests are reported with "COLOC-INTF-REQ <dialog token> <automatic
report enabled> <report timeout>" control interface events and
unsolicited reports can be sent with "COLOC_INTF_REPORT <hexdump>".
This commit adds support for reporting changes in the collocated
interference (Automatic Report Enabled == 1 and partial 3), but not for
periodic reports (2 and other part of 3).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Start scans more quickly if an open BSS advertising OWE transition mode
is found, but the matching OWE BSS has not yet been seen.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This commit introduces a threshold for OWE transition BSS selection,
which signifies the maximum number of selection attempts (scans) done
for finding OWE BSS.
This aims to do more scan attempts for OWE BSS and eventually select the
open BSS if the selection/scan attempts for OWE BSS exceed the
configured threshold.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Flush the PMKSA upon receiving assoc reject event without timeout
in the event data, to avoid trying the subsequent connections
with the old PMKID. Do not flush PMKSA if assoc reject is
received with timeout as it is generated internally from the
driver without reaching the AP.
This extends commit d109aa6cac ("SAE:
Flush PMKSA if an assoc reject without timeout is received") to handle
also the DPP AKM.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If the RADIUS authentication server dropped the cached ERP keys for any
reason, FILS authentication attempts with ERP fails and the previous
wpa_supplicant implementation ended up trying to use the same keys for
all consecutive attempts as well. This did not allow recovery from state
mismatch between the ERP server and peer using full EAP authentication.
Address this by trying to use full (non-FILS) authentication when trying
to connect to an AP using the same ERP realm with FILS-enabled network
profile if the previous authentication attempt had failed. This allows
new ERP keys to be established and FILS authentication to be used again
for the consecutive connections.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allows a single BSS/SSID to be used for both data connection and
OSU. In wpa_supplicant configuration, the current proto=OSEN
key_mgmt=OSEN combination is now allowing both the old separate OSEN
BSS/IE and the new RSN-OSEN to be used.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If no BSS entry can be found when processing association rejected event
from the driver for the special OWE case of unsupported
finite-cyclic-group, process the event as a connection failure instead
of just skipping the the OWE retry with another DH group.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
On an assoc_reject from the BSS with the status=77, a connection attempt
with the next supported group happens. The BSS considered here is from
current_bss which may be NULL at this point of time with SME-in-driver
case. Address this by getting the BSS from the bssid obtained in
association reject indication and skip the step if no BSS entry can be
found.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Flush the PMKSA upon receiving association reject event without timeout
in the event data in SME-in-driver case to avoid trying to use the old
PMKSA entry in subsequent connection attempts. Do not flush PMKSA if
association reject is received with timeout as it is generated
internally from the driver without reaching the AP. This is similar to
the SME-in-wpa_supplicant case that was already addressed within
sme_event_assoc_reject().
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allows user to get channel switch indication in station mode even
if wpa_supplicant is built without CONFIG_AP=y.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Timeout is increased by dfs_cac_ms from channel data, or by max CAC time
(10 minutes) if dfs_cac_ms is not defined. This is needed for some more
complex cases, e.g., when STA is acting as an active slave with DFS
offload enabled and decided to start CAC after receiving CONNECT
command, in such a case the 10 second timeout is too small and
wpa_supplicant need to wait for CAC completion or CAC timeout (up to 10
minutes).
Without such timeout modification wpa_supplicant will be unable to
connect to an AP on DFS channel, since the default authentication
timeout (10 s) is smaller than the minimum CAC time (60 s).
Tested with nl80211 DFS offload implementation.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
Rename DFS event handling functions, since they are located in ap.c and
refer to AP-mode only. Needed to add some STA-mode DFS event handling.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
Explicitly check the PMKSA cache entry to have matching SAE AKMP for the
case where determining whether to use PMKSA caching instead of new SAE
authentication. Previously, only the network context was checked, but a
single network configuration profile could be used with both WPA2-PSK
and SAE, so should check the AKMP as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
When connecting to a WPA-EAP network and the MAC address is changed
just before the association (for example by NetworkManager, which sets
a random MAC during scans), the authentication sometimes fails in the
following way ('####' logs added by me):
wpa_supplicant logs:
wlan0: WPA: RX message 1 of 4-Way Handshake from 02:00:00:00:01:00 (ver=1)
RSN: msg 1/4 key data - hexdump(len=22): dd 14 00 0f ac 04 d8 21 9d a5 73 98 88 26 ef 03 d2 ce f7 04 7d 23
WPA: PMKID in EAPOL-Key - hexdump(len=22): dd 14 00 0f ac 04 d8 21 9d a5 73 98 88 26 ef 03 d2 ce f7 04 7d 23
RSN: PMKID from Authenticator - hexdump(len=16): d8 21 9d a5 73 98 88 26 ef 03 d2 ce f7 04 7d 23
wlan0: RSN: no matching PMKID found
EAPOL: Successfully fetched key (len=32)
WPA: PMK from EAPOL state machines - hexdump(len=32): [REMOVED]
#### WPA: rsn_pmkid():
#### WPA: aa - hexdump(len=6): 02 00 00 00 01 00
#### WPA: spa - hexdump(len=6): 66 20 cf ab 8c dc
#### WPA: PMK - hexdump(len=32): b5 24 76 4f 6f 50 8c f6 a1 2e 24 b8 07 4e 9a 13 1b 94 c4 a8 1f 7e 22 d6 ed fc 7d 43 c7 77 b6 f7
#### WPA: computed PMKID - hexdump(len=16): ea 73 67 b1 8e 5f 18 43 58 24 e8 1c 47 23 87 71
RSN: Replace PMKSA entry for the current AP and any PMKSA cache entry that was based on the old PMK
nl80211: Delete PMKID for 02:00:00:00:01:00
wlan0: RSN: PMKSA cache entry free_cb: 02:00:00:00:01:00 reason=1
RSN: Added PMKSA cache entry for 02:00:00:00:01:00 network_ctx=0x5630bf85a270
nl80211: Add PMKID for 02:00:00:00:01:00
wlan0: RSN: PMKID mismatch - authentication server may have derived different MSK?!
hostapd logs:
WPA: PMK from EAPOL state machine (MSK len=64 PMK len=32)
WPA: 02:00:00:00:00:00 WPA_PTK entering state PTKSTART
wlan1: STA 02:00:00:00:00:00 WPA: sending 1/4 msg of 4-Way Handshake
#### WPA: rsn_pmkid():
#### WPA: aa - hexdump(len=6): 02 00 00 00 01 00
#### WPA: spa - hexdump(len=6): 02 00 00 00 00 00
#### WPA: PMK - hexdump(len=32): b5 24 76 4f 6f 50 8c f6 a1 2e 24 b8 07 4e 9a 13 1b 94 c4 a8 1f 7e 22 d6 ed fc 7d 43 c7 77 b6 f7
#### WPA: computed PMKID - hexdump(len=16): d8 21 9d a5 73 98 88 26 ef 03 d2 ce f7 04 7d 23
WPA: Send EAPOL(version=1 secure=0 mic=0 ack=1 install=0 pairwise=1 kde_len=22 keyidx=0 encr=0)
That's because wpa_supplicant computed the PMKID using the wrong (old)
MAC address used during the scan. wpa_supplicant updates own_addr when
the interface goes up, as the MAC can only change while the interface
is down. However, drivers don't report all interface state changes:
for example the nl80211 driver may ignore a down-up cycle if the down
message is processed later, when the interface is already up. In such
cases, wpa_supplicant (and in particular, the EAP state machine) would
continue to use the old MAC.
Add a new driver event that notifies of MAC address changes while the
interface is active.
Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
Add an event callback for EVENT_STATION_OPMODE_CHANGED to allow
user/application to get the notification whenever there is a change in a
station's HT/VHT op mode.
The new events:
STA-OPMODE-MAX-BW-CHANGED <addr> <20(no-HT)|20|40|80|80+80|160>
STA-OPMODE-SMPS-MODE-CHANGED <addr> <automatic|off|dynamic|static>
STA-OPMODE-N_SS-CHANGED <addr> <N_SS>
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
When the driver indicates that the connection is authorized (i.e., the
4-way handshake was completed by the driver), cancel the EAP
authentication timeout and set the EAP state machine to success state.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Extend the SME functionality to support the external authentication.
External authentication may be used by the drivers that do not define
separate commands for authentication and association
(~WPA_DRIVER_FLAGS_SME) but rely on wpa_supplicant's SME for the
authentication.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If the OWE network profile matches an open network which does not
advertise OWE BSS, allow open connection. The new owe_only=1 network
profile parameter can be used to disable this transition mode and
enforce connection only with OWE networks.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If a specific DH group for OWE is not set with the owe_group parameter,
try all supported DH groups (currently 19, 20, 21) one by one if the AP
keeps rejecting groups with the status code 77.
Signed-off-by: Jouni Malinen <j@w1.fi>
Update the replay counter after a roam for all cases. This restores the
design back to what it was before commit
01ef320f19 ('FILS: Update ERP next
sequence number with driver offload').
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_supplicant RESEND_ASSOC command can be used to request the
last (Re)Association Request frame to be sent to the AP to test FT
protocol behavior.
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
This can be used to test replay protection. The "RESET_PN" command in
wpa_supplicant and "RESET_PN <addr>" command in hostapd resets the local
counters to zero for the last configured key. For hostapd, the address
parameter specifies which STA this operation is for or selects GTK
("ff:ff:ff:ff:ff:ff") or IGTK ("ff:ff:ff:ff:ff:ff IGTK").
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was originally added to allow the IEEE 802.11 protocol to be
tested, but there are no known fully functional implementations based on
this nor any known deployments of PeerKey functionality. Furthermore,
PeerKey design in the IEEE Std 802.11-2016 standard has already been
marked as obsolete for DLS and it is being considered for complete
removal in REVmd.
This implementation did not really work, so it could not have been used
in practice. For example, key configuration was using incorrect
algorithm values (WPA_CIPHER_* instead of WPA_ALG_*) which resulted in
mapping to an invalid WPA_ALG_* value for the actual driver operation.
As such, the derived key could not have been successfully set for the
link.
Since there are bugs in this implementation and there does not seem to
be any future for the PeerKey design with DLS (TDLS being the future for
DLS), the best approach is to simply delete all this code to simplify
the EAPOL-Key handling design and to get rid of any potential issues if
these code paths were accidentially reachable.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add support for using the OWE Transition Mode element to determine the
hidden SSID for an OWE BSS that is used in transition mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_supplicant network parameter group_mgmt can be used to
specify which group management ciphers (AES-128-CMAC, BIP-GMAC-128,
BIP-GMAC-256, BIP-CMAC-256) are allowed for the network. If not
specified, the current behavior is maintained (i.e., follow what the AP
advertises). The parameter can list multiple space separate ciphers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
IEEE Std 802.11-2016, 11.11.6 specifies that a station that is unable to
make a requested measurement or refuses to make a measurement shall
respond only if the measurement request was received within an
individually addressed radio measurement request frame, but shall not
respond if such a request was received in a group addressed frame.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
dpp.h file requires openssl in order to compile, which breaks
compilation on systems without it.
Move DPP_OUI_TYPE to ieee802_11_defs.h and don't include dpp.h when
not really needed.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Commit 5538fc9309 ('FILS: Track completion
with FILS shared key authentication offload') added an additional case
for calling wpa_supplicant_event_assoc_auth() from EVENT_ASSOC handling
in case of FILS-completion with driver-based-SME. However, that checked
what placed outside the data != NULL case while data != NULL needs to
apply for this case as well due to wpa_supplicant_event_assoc_auth()
behavior. Move the data != NULL check to apply to both cases to avoid
potentially issues if a driver interface were to return EVENT_ASSOC
without the associate data. (CID 164708)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new AKM is used with DPP when using the signed Connector to derive
a PMK. Since the KCK, KEK, and MIC lengths are variable within a single
AKM, this needs number of additional changes to get the PMK length
delivered to places that need to figure out the lengths of the PTK
components.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds support for DPP Configuration Protocol using GAS. Full
generation and processing of the configuration object is not included in
this commit.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Current DFS domain information of the driver can be used in ap/dfs
to comply with DFS domain specific requirements like uniform spreading
for ETSI domain.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Add a new PMKSA cache entry within wpa_supplicant if a driver event from
offloaded FILS shared key authentication indicates a new PMKSA entry was
created.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This keeps the internal ERP information within wpa_supplicant in sync
with the driver when offloading FILS shared key authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Update the internal fils_completed state when offloading FILS shared key
authentication to the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In ap_scan=2 mode, wpa_supplicant_assoc_try() did not check whether the
SSID is temporarily disabled before trying to associate and this may
result in an infinite connect/disconnect loop. If the association
succeeds while the SSID is temporarily disabled, wpa_supplicant will
request to deauthenticate and that in turn will cause the SSID to be
temporarily disabled again. Fix that by postponing the association until
the SSID is no longer temporarily disabled.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
This adds an option to configure wpa_supplicant to use the perfect
forward secrecy option in FILS shared key authentication. A new build
option CONFIG_FILS_SK_PFS=y can be used to include this functionality. A
new runtime network profile parameter fils_dh_group is used to enable
this by specifying which DH group to use. For example, fils_dh_group=19
would use FILS SK PFS with a 256-bit random ECP group.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds STA side addition of OWE Diffie-Hellman Parameter element into
(Re)Association Request frame and processing it in (Re)Association
Response frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
There's no point in making the code use a stack buffer and first copying
the string there, only to copy it again to the output. Make the output
directly use the reason string.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows PMKSA cache entries for FILS-enabled BSSs to be shared
within an ESS when the BSSs advertise the same FILS Cache Identifier
value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds reason for timeout in event CTRL-EVENT-ASSOC-REJECT whenever
connection failure happens because of timeout. This extends the
"timeout" parameter in the event to include the reason, if available:
timeout=scan, timeout=auth, timeout=assoc.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 8d1e693186 ('Use estimated
throughput to avoid signal based roaming decision') added a check for
the current BSS estimated throughput being significantly higher than the
selected BSS estimated throughput. However, this case for skipping a
roam used "return 1" which actually allows the roam. Fix this by
returning 0 in this case.
Signed-off-by: Jouni Malinen <j@w1.fi>
Increase the EAPOL RX frame timeout from 100 to 200 ms. This fixes lack
of optimization (i.e., first EAPOL frame dropped) in occasional roaming
and authentication cases on EAP networks if the kernel events can be
reordered and delayed a bit longer.
Signed-off-by: Tomoharu Hatano <tomoharu.hatano@sonymobile.com>
This adds a call to the notify_beacon_loss() callback functions when
beacon loss is detected. In addition, a new CTRL-EVENT-BEACON-LOSS event
is made available through the wpa_supplicant control interface.
Signed-off-by: Jouni Malinen <j@w1.fi>
Beacon Report Radio Measurement is defined in IEEE Std 802.11-2016,
11.11.9.1. Beacon Report is implemented by triggering a scan on the
requested channels with the requested parameters.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This makes wpa_supplicant behavior more consistent with FLUSH command to
clear all state. Previously, it was possible for an ongoing scan to be
aborted when the FLUSH command is issued and the scan results from that
aborted scan would still be processed and that would update the BSS
table which was supposed to cleared by the FLUSH command.
This could result in hwsim test case failures due to unexpected BSS
table entries being present after the FLUSH command.
Signed-off-by: Jouni Malinen <j@w1.fi>
This provides more details on BSS selection process in the debug log.
Previously, the BSSs that were not either the current or the selected
one were not necessarily printed at all. Now all BSSs that match the
currently selected network are listed with their frequency and signal
strength details.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, the estimated throughput was used to enable roaming to a
better AP. However, this information was not used when considering a
roam to an AP that has better signal strength, but smaller estimated
throughput. This could result in allowing roaming from 5 GHz band to 2.4
GHz band in cases where 2.4 GHz band has significantly higher signal
strength, but still a lower throughput estimate.
Make this less likely to happen by increasing/reducing the minimum
required signal strength difference based on the estimated throughputs
of the current and selected AP. In addition, add more details about the
selection process to the debug log to make it easier to determine whaty
happened and why.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, a build without IBSS RSN support tried to start/join an IBSS
even if the profile was configured with RSN parameters. This does not
work and resulted in quite confusing debug log. Make this clearer by
explicitly checking for this case and reject the connection attempt with
a clearer debug log entry instead of trying something that is known to
fail.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Decrypt the AES-SIV protected elements and verify Key-Auth. Parse and
configure keys to the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Scan results were not propagated to all interfaces if scan results
started a new operation, in order to prevent concurrent operations. But
this can cause other interfaces to trigger a new scan when scan results
are already available. Instead, always notify other interfaces of the
scan results, but note that new operations are not allowed.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
When scheduled scan stops without the interface request (for example,
driver stopped it unexpectedly), start a regular scan to continue
scanning for networks and avoid being left with no scan at all.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
In some cases, after a sudden AP disappearing and reconnection to
another AP in the same ESS, if another scan occurs, wpa_supplicant might
try to roam to the old AP (if it was better ranked than the new one)
because it is still saved in BSS list and the blacklist entry was
cleared in previous reconnect. This attempt is going to fail if the AP
is not present anymore and it'll cause long disconnections.
Remove an AP that is probably out of range from the BSS list to avoid
such disconnections. In particular mac80211-based drivers use the
WLAN_REASON_DISASSOC_DUE_TO_INACTIVITY reason code in locally generated
disconnection events for cases where the AP does not reply anymore.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
As the scan channels might need to change when the channel list has been
updated by the kernel. Use the simulated sched_scan timeout
(wpas_scan_restart_sched_scan()) to handle a possible race where an
ongoing sched_scan has stopped asynchronously while trying to restart a
new sched_scan.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Add a testing mechanism to allow association disallowed set by AP to be
ignored. This can be used to verify AP behavior for disallowing a
specific association.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Implement "SET ignore_auth_resp <0/1>" command to simulate auth/assoc
response loss and EAPOL RX packet loss by ignoring corresponding
incoming events.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
When an interface becomes disabled (e.g., when RF-kill becomes blocked)
we should clear the stored scan results to avoid maintaining stale
information.
Fix this by flushing the BSS entries when an interface becomes
disabled.
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
The new network profile parameter group_rekey can now be used to specify
the group rekeying internal in seconds for IBSS.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the driver indicates a roamed event with already completed
authorization, altAccept = TRUE could have resulted in the EAP state
machine ending up in the FAILURE state from the INITIALIZE state. This
is not correct behavior and similar cases were already addressed for FT
and WPA-PSK. Fix the offloaded roamed+authorized (EAP/PMKSA caching)
case by doing similar changes to EAPOL/EAP state variable updates during
association event handling.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows P2P Listen to be offloaded to device to enhance power
saving.
To start P2P listen offload, from wpa_cli interface, issue the command:
p2p_lo_start <freq> <period> <interval> <count>
To stop P2P listen offload, issue the command:
p2p_lo_stop
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a new "timeout" argument to the event message if the nl80211 message
indicates that the connection failure is not due to an explicit AP
rejection message. This makes it easier for external programs to figure
out why the connection failed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The P2P Device interface can only send Public Action frames. Non-Public
Action frames must be sent over a group interface. The previous
implementation sometimes tried to send non-Public Action frames such as
GO Discoverability over the P2P Device interface, however, the source
address of the frame was set to the group interface address so the code
in offchannel.c knew to select the correct interface for the TX.
The check breaks when the P2P Device and group interfaces have the same
MAC address. In this case the frame will be sent over the P2P Device
interface and the send will fail.
Fix this problem in two places:
1. In offchannel, route non-Public Action frames to the GO
interface when the above conditions are met.
2. When a TX_STATUS event arrives on such routed frame, it will
arrive on the GO interface but it must be handled by the P2P Device
interface since it has the relevant state logic.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
The NL80211_CMD_WIPHY_REG_CHANGE can be handled by any of the
interfaces that are currently controlled by the wpa_supplicant.
However, some applications expect the REGDOM_CHANGE event to be
sent on the control interface of the initially added interface
(and do not expect the event on any of child interfaces).
To resolve this, when processing NL80211_CMD_WIPHY_REG_CHANGE,
find the highest parent in the chain, and use its control interface
to emit the CTRL-EVENT-REGDOM-CHANGE event.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Since ieee80211w=2 is an explicit configuration to wpa_supplicant, the
connection attempt for such non-PMF (non-RSN) capable networks should be
skipped.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Handle radio measurement request that contains LCI request. Send
measurement report based on a configurable LCI report element. The LCI
report element is configured over the control interface with
SET lci <hexdump of the element>
and cleared with
SET lci ""
Signed-off-by: David Spinadel <david.spinadel@intel.com>
When a station starts an association to a Hotspot 2.0 network, request
the driver to do the following, based on the BSS capabilities:
1. Enable gratuitous ARP filtering
2. Enable unsolicited Neighbor Advertisement filtering
3. Enable unicast IP packet encrypted with GTK filtering if
DGAF disabled bit is zero
Clear the filter configuration when the station interface is
disassociated.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Add a new value 2 to the pbss parameter of wpa_ssid structure, which
means "don't care". This value is used in infrastructure mode to request
connection to either AP or PCP, whichever is available in the scan
results. The value is also used in regular WPS (not P2P group formation)
to make WPS work with devices running as either AP or PCP.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Commit dd271857a5 ('Skip normal scan when
PNO is already in progress') fixed issues with normal scans getting
rejected by the driver when PNO scan is already running. The part about
skipping such a scan request is fine, but the part about clearing
wpa_s->pno back to 0 in EVENT_SCHED_SCAN_STOPPED handler is problematic.
If PNO is stopped ("SET pno 0") and then restarted ("SET pno 1")
immediately, it is possible for the EVENT_SCHED_SCAN_STOPPED event from
the stopping part to be received only after the new PNO instance has
been started. This would have resulted in clearing wpa_s->pno and the
driver and wpa_supplicant getting out of sync. This would then prevent
PNO from being stopped with "SET pno 0" (that fails if wpa_s->pno == 0).
Fix this race condition by reverting the wpa_s->pno = 0 addition from
the EVENT_SCHED_SCAN_STOPPED handler.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This struct in the union is empty, but the design of using a zero-length
u8 array here is not fully compatible with C++ and can result in
undesired compiler warnings. Since there are no non-IE fields in the
Probe Request frames, get the location of the variable length IEs simply
by using the pointer to the frame header and the known header length.
Signed-off-by: Jouni Malinen <j@w1.fi>
The initial connection to an ESS was already explicitly increasing the
likelihood of picking a 5 GHz BSS. While the throughput estimation is
likely to do same for the roaming decision, it might be possible that
that does not cover all cases. Add couple of dB extra preference for 5
GHz in case the roaming decision falls back to comparing signal levels.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new wpa_supplicant command line argument -M can be used to describe
matching rules with a wildcard interface name (e.g., "wlan*").
This is very useful for systems without udev (Linux) or devd (FreeBSD).
Signed-off-by: Roy Marples <roy@marples.name>
Interface additions/removals are not guaranteed to be for the driver
listening to the kernel events. As such, send the events to
wpa_supplicant_event_global() which can then pick the correct interface
registered with wpa_supplicant to send the event to.
Signed-off-by: Roy Marples <roy@marples.name>
The 4-way handshake fails with the error "WPA: No wpa_ie set - cannot
generate msg 2/4" while connecting to OSEN network with drivers that
indicate used Association Request frame elements because OSEN IE is not
handled in wpa_supplicant_event_associnfo() if data->assoc_info.req_ies
is not NULL.
Signed-off-by: Daichi Ueura <daichi.ueura@sonymobile.com>
(Re)Association Response frame with status code other than 0 is now
notified over DBUS as a part of PropertiesChanged signal. This can be
used by application in case AP is denying association with status code
17 (band steering) so that it does not interfere in the BSSID selection
logic of wpa_supplicant.
Signed-off-by: Naveen Singh <nasingh@google.com>
An interface can be disabled while it has an ongoing scan request.
In such a case, when the scan results notification is received,
it was being ignored (as the interface is already disabled) so the
scan state was not cleared. This can cause undetermined behavior
for the next scan request.
To handle this, clear the scan state when EVENT_SCAN_RESULTS is
received and the interface is disabled.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Commit 02e122a995 ('Reschedule scan from
wpas_stop_pno if it was postponed') uses wpa_s->scanning as the only
condition for automatically starting a postponed scan request from
EVENT_SCHED_SCAN_STOPPED event handler. However, wpa_s->scanning may be
set for sched_scan and as such, this can result in unexpected extra
scans without there having been any real postponed request.
Make this more accurate by verifying that there really is a pending
request for a scan before speeding up its start.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If WPA2 is used, MBO AP must enable PMF. Refuse to select a BSS that has
MBO and WPA2 enabled without PMF.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add the transition candidate list to BSS Transition Management Response
frame. The candidates preference is set using the regular wpa_supplicant
BSS selection logic. If the BSS transition request is rejected and
updated scan results are not available, the list is not added.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add parsing of MBO IE in BSS Transition Management Request frames. If
the MBO IE includes the association retry delay attribute, do not try to
reconnect to the current BSS until the delay time is over.
If the MBO IE includes the cellular data connection preference attribute
or the transition rejection reason attribute, send a message to upper
layers with the data.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Prevent association to MBO APs that have association disallowed
attribute in MBO IE in Beacon or Probe Response frames.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
PBSS (Personal Basic Service Set) is a new BSS type for DMG
networks. It is similar to infrastructure BSS, having an AP-like
entity called PCP (PBSS Control Point), but it has few differences.
PBSS support is mandatory for IEEE 802.11ad devices.
Add a new "pbss" argument to network block. The argument is used
in the following scenarios:
1. When network has mode=2 (AP), when pbss flag is set will start
as a PCP instead of an AP.
2. When network has mode=0 (station), when pbss flag is set will
connect to PCP instead of AP.
The function wpa_scan_res_match() was modified to match BSS according to
the pbss flag in the network block (wpa_ssid structure). When pbss flag
is set it will match only PCPs, and when it is clear it will match only
APs.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Since hostapd supports ACS now, let's enable its support in
wpa_supplicant as well when starting AP mode.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
[u.oelmann@pengutronix.de: rebased series from hostap_2_1~944 to master]
[u.oelmann@pengutronix.de: adjusted added text in defconfig]
Signed-off-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
Let's reuse hostapd code for such handling. This will be useful to get
ACS support into wpa_supplicant where this one needs to handle the
survey event so it fills in the result ACS subsystem will require.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
[u.oelmann@pengutronix.de: rebased series from hostap_2_1~944 to master]
Signed-off-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
Previously, when wpa_supplicant received bgscan results with a preferred
network, it connected to that network without disconnecting from the
previous one. This might result in an inconsistent state of upper
layers.
Fix this by disconnecting from the current AP before connecting to the
new one when the network profile changes and there is an existing
connection.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
If scan results arrive during the connection process, the network
selection function was called, interrupting the current connection.
While a regular scan is mutually exclusive with connection establishment
via the nature of radio work, there's no such protection for scheduled
scan. Prevent network selection while a connection is in progress.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Previously, MB IEs were parsed only from association event. Try to get
MB IEs from other management frames like Probe Response frames. The MB
IEs from the association event may not be up-to-date and in some cases
may actually be missing and updating the information based on other
frames can improve robustness of FST exchanges.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows offloaded roaming to inform user space of the change in IP
subnet post roaming. The device may have roamed to a network which is in
a different subnet which will result in IP connectivity loss. Indicating
the change in subnet enables the user space to refresh the IP address or
to perform IP subnet validation if unknown status is indicated.
The driver indication is reported with a new event from wpa_supplicant
in the following format:
CTRL-EVENT-SUBNET-STATUS-UPDATE status=<0/1/2>
where
0 = unknown
1 = IP subnet unchanged (can continue to use the old IP address)
2 = IP subnet changed (need to get a new IP address)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If "STA_AUTOCONNECT 0" has been used to disable automatic connection on
disconnection event and the driver indicates a failure for the data
connection after successful WPS handshake, it is possible to hit a case
where wpa_s->disconnected is set to 1 and further attempts to connect
shall stop.
While "STA_AUTOCONNECT 0" is used to disable automatic reconnection
attempts in general, this specific WPS case can benefit from trying
again even with that configuration for a short period of time. Extend
the wpa_supplicant re-enable-networks-after-WPS 10 second timeout to
apply for ignoring disabled STA_AUTOCONNECT immediately after a WPS
provisioning step.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The AP is not expected to send out a WNM-Sleep Mode Response frame
without the STA trying to use WNM-Sleep Mode. Drop such unexpected
responses to reduce unnecessary processing of the frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of trying to associate in configuration that is known to result
in the AP rejecting the association, reject the BSS candidate based on
the MFPR=1 RSN capability when STA configuration has PMF disabled.
Signed-off-by: Jouni Malinen <j@w1.fi>
Channel switch notification was handled only for AP/GO interfaces. As
the notification can be sent on other interface types as well, extend
the handling to handle other interface types.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Do not consider moving GOs to a new channel if one of them is in the
middle of CSA. In addition, call wpas_p2p_update_channel_list() after
EVENT_CH_SWITCH is handled.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Allow wpa_supplicant to use vendor scan (if supported by the driver)
together with the normal nl80211 scan and handling external scan events.
Since this results in possibility of concurrent scan operations, some of
the operations related to scan results need to check more carefully when
an event is relevant for a specific interface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
