This extends wpa_supplicant DPP implementation to retransmit DPP
Authentication Response frame every 10 seconds up to 5 times if the peer
does not reply with DPP Authentication Confirm frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, this command stopped listen operation immediately, but if
there was an ongoing authentication exchange, a new listen operation was
started. This is not really expected behavior, so stop the
authentication exchange first with this command to avoid restarting
listen operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends wpa_supplicant to iterate over all available channels from
the intersection of what the peer indicates and the local device
supports when initiating DPP Authentication. In addition, retry DPP
Authentication Request frame up to five times if no response is
received.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit introduces the ACS functionality for the autonomous GO. The
optional parameter <freq> in p2p_group_add is enhanced to carry a value
"acs" with the intention to select the channels among any supported
band. freq = 2 / 5 carry the need to select the channels only in the
respective bands 2.4 / 5 GHz. This functionality is on top of the host
driver's capability to offload ACS, which is advertized through
WPA_DRIVER_FLAGS_ACS_OFFLOAD.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows wpa_supplicant dpp_config_obj_override,
dpp_discovery_override, and dpp_groups_override parameters to be cleared
by setting them to a zero-length value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a generic mechanism for configuring the DPP implementation to behave
in particular different (mostly incorrect) ways for protocol testing
purposes. The new dpp_test parameter can be set to a non-zero integer to
indicate a specific behavior. This is only available in
CONFIG_TESTING_OPTIONS=y builds.
This commit include cases for an extra attribute being added after the
Wrapped Data attribute and Initiator/Responder capabilities having an
unexpected zero capability.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_supplicant RESEND_ASSOC command can be used to request the
last (Re)Association Request frame to be sent to the AP to test FT
protocol behavior.
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new wpa_supplicant "KEY_REQUEST <error=0/1> <pairwise=0/1>" command
can be used to request an EAPOL-Key Request frame to be sent to the AP.
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
This can be used to test replay protection. The "RESET_PN" command in
wpa_supplicant and "RESET_PN <addr>" command in hostapd resets the local
counters to zero for the last configured key. For hostapd, the address
parameter specifies which STA this operation is for or selects GTK
("ff:ff:ff:ff:ff:ff") or IGTK ("ff:ff:ff:ff:ff:ff IGTK").
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was originally added to allow the IEEE 802.11 protocol to be
tested, but there are no known fully functional implementations based on
this nor any known deployments of PeerKey functionality. Furthermore,
PeerKey design in the IEEE Std 802.11-2016 standard has already been
marked as obsolete for DLS and it is being considered for complete
removal in REVmd.
This implementation did not really work, so it could not have been used
in practice. For example, key configuration was using incorrect
algorithm values (WPA_CIPHER_* instead of WPA_ALG_*) which resulted in
mapping to an invalid WPA_ALG_* value for the actual driver operation.
As such, the derived key could not have been successfully set for the
link.
Since there are bugs in this implementation and there does not seem to
be any future for the PeerKey design with DLS (TDLS being the future for
DLS), the best approach is to simply delete all this code to simplify
the EAPOL-Key handling design and to get rid of any potential issues if
these code paths were accidentially reachable.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add support for using the OWE Transition Mode element to determine the
hidden SSID for an OWE BSS that is used in transition mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Update the default scan IEs when OCE is enabled/disabled to the
driver/firmware, so that the correct IEs will be sent out by the
driver/firmware in Probe Request frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new "SET sae_commit_override <hexdump>" control interface command
can be used to force wpa_supplicant to override SAE commit message
fields for testing purposes. This is included only in
CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Clear the get_pref_freq_list_override in p2p_ctrl_flush(). This fixes
the case when a dedicated P2P device interface is used.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add changes to control interface command get_capability to advertize
FILS capability, FILS AKMs suites, and FILS Authentication algorithms
based on the driver capabilities.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add support to scan for a specific BSSID through the wpa_supplicant
control interface.
Usage: wpa_cli scan bssid=ab:bc:cd🇩🇪ef:12
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The DPP Configurator can use this new command to generate its own signed
connector for the network that it manages.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows wpa_supplicant to be configured to act as the configurator
in the case where a peer device initiates DPP Authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This implements genric PKEX functionality in src/common/dpp.c and glue
code to use this in wpa_supplicant (i.e, hostapd DPP implementation does
not yet support PKEX).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new AKM is used with DPP when using the signed Connector to derive
a PMK. Since the KCK, KEK, and MIC lengths are variable within a single
AKM, this needs number of additional changes to get the PMK length
delivered to places that need to figure out the lengths of the PTK
components.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds support for DPP Configuration Protocol using GAS. Full
generation and processing of the configuration object is not included in
this commit.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add wpa_supplicant control interface commands for parsing the bootstrap
info URI from a QR Code (get peer public key) and to generate a new
bootstrap info with private key for local use. The optional
key=<hexdump> argument to the DPP_BOOTSTRAP_GEN command can be used to
specify the bootstrapping private key in OpenSSL ECPrivateKey DER
encoding format. This results in the local bootstrapping information
entry being created with the specified key instead of generating a new
random one.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Change in any network configuration at runtime will cause flush to
PMKSA cache. For most of the network parameters if there is no change
in value, PMKSA flush is not performed except 'bssid' and 'priority'.
Add 'bssid_hint' to exemption list of avoiding PMKSA flush on change.
This is needed to complete change in commit
43a356b268 ('Provide option to configure
BSSID hint for a network').
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add support to set ignore assoc disallow to the driver so that the
driver ignores assoc disallowed bit set by APs while connecting. This is
used by drivers that handle BSS selection and roaming internally.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
PMKSA_ADD and MESH_PMKSA_ADD command arguments include keying material,
so show it in debug log only if requested to do with the command line -K
argument.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a mechanism to configure the candidates for BTM query candidate list
manually. This can be used to verify AP behavior for various candidates
preferences.
usage:
wnm_bss_query <reason> [neighbor=<BSSID>,<BSSID information>,
<operating class>,<channel number>,
<PHY type>[,<hexdump of optional subelements>]]
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Previously, ANQP_GET required at least one IEEE 802.11 ANQP-element to
be requested. This is not really necessary, so allow a case where
num_ids == 0 as long as the request includes at least one Hotspot 2.0 or
MBO ANQP-element.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
MBO techspec v0.0_r27 changed the MBO ANQP-element format. The MBO
element in ANQP query should now include an MBO Query List element that
contains a list of MBO elements to query.
Add API to add the MBO Query List to an ANQP query.
Format:
ANQP_GET <addr> <info_id>[,<info_id>]...[,mbo:<subtype>...]
Example for querying neighbor report with MBO cellular data
connection preference:
ANQP_GET <bssid> 272,mbo:2
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This functionality was originally added in commit
204c9ac4ee ('Extend select_network command
with freq= to reduce scan time') re-using wpa_s->manual_scan_freqs and
MANUAL_SCAN_REQ. That got broken when commit
35d403096e ('Set NORMAL_SCAN_REQ on
SELECT_NETWORK/ENABLE_NETWORK') started overriding wpa_s->scan_req for
SELECT_NETWORK.
Fix this by adding a new scan frequency list specifically for
SELECT_NETWORK so that this does not need to depend on any specific
wpa_s->scan_req value.
Signed-off-by: Jouni Malinen <j@w1.fi>
The PMKSA_GET and PMKSA_ADD commands can now use an optional extra
parameter to fetch and add PMKSA cache entries with the FILS Cache
Identifier.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new "SET ric_ies <hexdump>" control interface command can now be
used to request wpa_supplicant to add the specified RIC elements into
Reassociation Request frame when using FT protocol. This is mainly for
testing purposes.
Signed-off-by: Jouni Malinen <j@w1.fi>
This new P2P_SET parameter uses <op_class>:<channel> format and is used
mainly for testing purposes to allow overriding the value of the GO
Negotiation Response frame Operating Channel attribute.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This can be used to override driver get_pref_freq_list() operation for
more convenient testing of preferred frequency list functionality.
Override string format:
<if_type1>:<freq1>,<freq2>,... <if_type2>:...
if_type: 0=STATION, 2=AP, 3=P2P_GO, 4=P2P_CLIENT, 8=TDLS, 9=IBSS
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add support to set sched scan relative RSSI parameters so that the
drivers can report BSSs after relative comparision with the current
connected BSS. This feature is applicable only when in connected mode.
The below commands can be used to configure relative RSSI parameters
SET relative_rssi <disable|rssi_value>
disable - to disable the feature
rssi_value - amount of relative RSSI in dB
SET relative_band_adjust <band:adjust_value>
band - "2G" or "5G" for 2.4 GHz or 5 GHz respectively
adjust_value - amount of RSSI to be adjusted in dB
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Relying on the group_capab from the P2P peer information can result in
improper information on whether the peer is currently operating as a GO.
However, there is a known implementation in Android that does this.
To reduce issues from this misuse in upper layer to try to determine
whether a specific peer is operationg a group, override the group_capab
value in P2P_PEER output with 0 if there are no BSS entries with the
peer P2P Device as a GO. This is not a perfect information since there
may not have been a recent scan on all channels, but this results in
less issues than trying to decide between new group formation and
joining an existing group based on stale or incorrect information.
Since no upper layer application is really supposed to use the
group_capab field value in P2P_PEER command, this change should not
cause any impact for properly design components and the possibility of
regressions is limited to cases that are already known to work
incorrectly in number of identifiable cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
To be more consistent with existing hwaddr_aton() and hexstr2bin()
callers, check the return values in this test command.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new wpa_supplicant control interface commands FILS_HLP_REQ_FLUSH and
FILS_HLP_REQ_ADD can now be used to request FILS HLP requests to be
added to the (Re)Association Request frame whenever FILS authentication
is used.
FILS_HLP_REQ_ADD parameters use the following format:
<destination MAC address> <hexdump of payload starting from ethertype>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These commnds are mesh version of PMKSA_GET/ADD commands. So the usage
and security risk is similar to them. Refer to
commit 3459381dd2 ('External persistent
storage for PMKSA cache entries') also.
The MESH_PMKSA_GET command requires peer MAC address or "any" as an
argument and outputs appropriate stored PMKSA cache. And the
MESH_PMKSA_ADD command receives an output of MESH_PMKSA_GET and re-store
the PMKSA cache into wpa_supplicant. By using re-stored PMKSA cache,
wpa_supplicant can skip commit message creation which can use
significant CPU resources.
The output of the MESH_PMKSA_GET command uses the following format:
<BSSID> <PMKID> <PMK> <expiration in seconds>
The example of MESH_PMKSA_ADD command is this.
MESH_PMKSA_ADD 02:00:00:00:03:00 231dc1c9fa2eed0354ea49e8ff2cc2dc cb0f6c9cab358a8146488566ca155421ab4f3ea4a6de2120050c149b797018fe 42930
MESH_PMKSA_ADD 02:00:00:00:04:00 d7e595916611640d3e4e8eac02909c3c eb414a33c74831275f25c2357b3c12e3d8bd2f2aab6cf781d6ade706be71321a 43180
This functionality is disabled by default and can be enabled with
CONFIG_PMKSA_CACHE_EXTERNAL=y build configuration option.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This control interface command can be used to inject scan results from
test scripts to make it easier to test various scan result processing
operations.
Signed-off-by: Jouni Malinen <j@w1.fi>
These parameters are global configuration parameters for wpa_supplicant
and the special control interface SET command handlers for them were
preventing the configuration update. Make this more consistent by
updating the configuration parameter as well since that is what all the
other SET <global config param> commands do.
Signed-off-by: Jouni Malinen <j@w1.fi>
non_pref_chan is a global configuration parameter for wpa_supplicant and
the special control interface SET command handler for it was preventing
the configuration update. Make this more consistent by updating the
configuration parameter as well since that is what all the other SET
<global config param> commands do.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was previously done for SCAN_RESULTS, but the BSS control interface
command did not show a similar flag. In addition, change "WPA2" to "RSN"
for mesh BSS to be consistent with the SCAN_RESULTS output.
Commit 638d945679 ('mesh: Show [MESH] flag
in scan results') did similar changes for SCAN_RESULTS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit extends the BSS commands to include "BSS CURRENT" as a way
to get the current BSS without having to walk the BSS list matching
against BSSID+SSID returned from the STATUS command.
This returns the BSS stored in wpa_s->current_bss.
Signed-off-by: Joel Cunningham <joel.cunningham@me.com>
This makes both the Probe Response and Beacon frame IEs available to
upper layers if scan results include both IE sets. When the BSS command
mask includes WPA_BSS_MASK_BEACON_IE, a new beacon_ie=<hexdump> entry
will be included in output if the BSS entry has two separate sets of IEs
(ie=<hexdump> showing the Probe Response frame contents and
beacon_ie=<hexdump> the Beacon rame contents).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds new wpa_supplicant control interface commands PMKSA_GET and
PMKSA_ADD that can be used to store PMKSA cache entries in an external
persistent storage when terminating a wpa_supplicant process and then
restore those entries when starting a new process. The previously added
PMKSA-CACHE-ADDED/REMOVED events can be used to help in synchronizing
the external storage with the memory-only volatile storage within
wpa_supplicant.
"PMKSA_GET <network_id>" fetches all stored PMKSA cache entries bound to
a specific network profile. The network_id of the current profile is
available with the STATUS command (id=<network_id). In addition, the
network_id is included in the PMKSA-CACHE-ADDED/REMOVED events. The
output of the PMKSA_GET command uses the following format:
<BSSID> <PMKID> <PMK> <reauth_time in seconds> <expiration in seconds>
<akmp> <opportunistic>
For example:
02:00:00:00:03:00 113b8b5dc8eda16594e8274df4caa3d4 355e98681d09e0b69d3a342f96998aa765d10c4459ac592459b5efc6b563eff6 30240 43200 1 0
02:00:00:00:04:00 bbdac8607aaaac28e16aacc9152ffe23 e3dd6adc390e685985e5f40e6fe72df846a0acadc59ba15c208d9cb41732a663 30240 43200 1 0
The PMKSA_GET command uses the following format:
<network_id> <BSSID> <PMKID> <PMK> <reauth_time in seconds> <expiration
in seconds> <akmp> <opportunistic>
(i.e., "PMKSA_ADD <network_id> " prefix followed by a line of PMKSA_GET
output data; however, the reauth_time and expiration values need to be
updated by decrementing them by number of seconds between the PMKSA_GET
and PMKSA_ADD commands)
For example:
PMKSA_ADD 0 02:00:00:00:03:00 113b8b5dc8eda16594e8274df4caa3d4 355e98681d09e0b69d3a342f96998aa765d10c4459ac592459b5efc6b563eff6 30140 43100 1 0
PMKSA_ADD 0 02:00:00:00:04:00 bbdac8607aaaac28e16aacc9152ffe23 e3dd6adc390e685985e5f40e6fe72df846a0acadc59ba15c208d9cb41732a663 30140 43100 1 0
This functionality is disabled be default and can be enabled with
CONFIG_PMKSA_CACHE_EXTERNAL=y build configuration option. It should be
noted that this allows any process that has access to the wpa_supplicant
control interface to use PMKSA_ADD command to fetch keying material
(PMK), so this is for environments in which the control interface access
is restricted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes wpa_supplicant behavior more consistent with FLUSH command to
clear all state. Previously, it was possible for an ongoing scan to be
aborted when the FLUSH command is issued and the scan results from that
aborted scan would still be processed and that would update the BSS
table which was supposed to cleared by the FLUSH command.
This could result in hwsim test case failures due to unexpected BSS
table entries being present after the FLUSH command.
Signed-off-by: Jouni Malinen <j@w1.fi>
This commit adds a control interface command to configure the TDLS
trigger mode to the host driver. This TDLS mode is configured through
the "SET tdls_trigger_control" control interface command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
"GET_CAPABILITY fils" used to return "FILS" based on wpa_supplicant
configuration. This can be made more useful by checking both for
wpa_supplicant and driver support for FILS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This can be used to check whether the running wpa_supplicant version was
built with CONFIG_FILS=y.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to figure out why autoscan is not used even when
being configured through the control interface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends ANQP_GET command to support querying MBO cellular
preference also. The cellular preference can be requested along with
neigbor report by appending mbo:1 to the command arguments.
For example:
ANQP_GET <bssid> 272,mbo:1
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This code sequence was already used at two different places (and an
additional one has been proposed), so add a common helper function to
avoid having to copy-paste this functionality in multiple locations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
For testing purposes, it is useful to have an option to be able to
reject BTM Request sent by AP in order to verify the AP behavior upon
BTM Request rejection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a testing mechanism to allow association disallowed set by AP to be
ignored. This can be used to verify AP behavior for disallowing a
specific association.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Implement "SET ignore_auth_resp <0/1>" command to simulate auth/assoc
response loss and EAPOL RX packet loss by ignoring corresponding
incoming events.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
All the 3 control interfaces: socket based, dbus & binder needs to
perform the same sequence of steps for network add/remove. So, move
these to a common utility method in |wpa_supplicant.c| instead of
duplicating the code everywhere.
Signed-off-by: Roshan Pius <rpius@google.com>
Move out the disconnect command handling from |ctrl_iface.c| to
|wpa_supplicant.c| so that it can be reused across the different
control interfaces (socket, dbus & binder).
Signed-off-by: Roshan Pius <rpius@google.com>
This is needed for hwsim test cases to allow multiple STA-initiated SA
Query operations in short amount of time.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is mainly for testing purposes to allow multiple FETCH_OSU ANQP
operations to be ran without having to wait for full scan between each
query.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows P2P Listen to be offloaded to device to enhance power
saving.
To start P2P listen offload, from wpa_cli interface, issue the command:
p2p_lo_start <freq> <period> <interval> <count>
To stop P2P listen offload, issue the command:
p2p_lo_stop
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In some cases parsing of the mesh scan info for a BSS or the P2P scan
info can fail. One reason can be that the Beacon/Probe Response frame
contained malformed length vendor IEs which are not parsed when adding
to the BSS table. Instead of skipping the whole BSS of the BSS command,
just skip the part that failed to parse.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
This allows using P2PS config method with or without PIN for connection.
wpa_supplicant should internally handle the default PIN "12345670" and
shall also allow connection irrespective of PIN used in P2P_CONNECT.
For example,
1. P2P_CONNECT 02:2a:fb:22:22:33 p2ps
2. P2P_CONNECT 02:2a:fb:22:22:33 xxxxxxxx p2ps
Where the second one is maintained for backwards compatibility.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
work->type was pointing to the allocated work->ctx buffer and the debug
print in radio_work_free() ended up using freed memory if a started
external radio work was removed as part of FLUSH command operations. Fix
this by updating work->type to point to a constant string in case the
dynamic version gets freed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to write hwsim test cases to verify management
frame processing sequences with dropped or modified frames. When
ext_mgmt_frame_handling is used, this new command can be used to request
wpa_supplicant to process a received a management frame, e.g., based on
information reported in the MGMT-RX events.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows local GO to fetch the P2P Interface Address of a P2P Client
in the group based on the P2P Device Address for the client. This
command should be sent only on a group interface (the same peer may be
in multiple concurrent groups).
Usage:
P2P_GROUP_MEMBER <P2P Device Address>
Output:
<P2P Interface Address>
Signed-off-by: Purushottam Kushwaha <pkushwah@qti.qualcomm.com>
Parse a received neighbor report and report for each neighbor report the
data received for it:
RRM-NEIGHBOR-REP-RECEIVED bssid=<BSSID> info=0x<hex> op_class=<class> chan=<chan> [lci=hex] [civic=hex]
Note that this modifies the previous format that originally reported
only the length of the received frame.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Handle radio measurement request that contains LCI request. Send
measurement report based on a configurable LCI report element. The LCI
report element is configured over the control interface with
SET lci <hexdump of the element>
and cleared with
SET lci ""
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add an option to request LCI and Location Civic Measurement in Neighbor
Report Request frame, as described in IEEE P802.11-REVmc/D5.0, 9.6.7.6.
Note: This changes the encoding format of the NEIGHBOR_REP_REQUEST
ssid=<val> parameter. This used to be parsed as raw SSID data which is
problematic for accepting additional parameters. The new encoding allows
either a string within double-quotation marks or a hexdump of the raw
SSID.
Thew new format:
NEIGHBOR_REP_REQUEST [ssid=<SSID>] [lci] [civic]
Signed-off-by: David Spinadel <david.spinadel@intel.com>
This avoids unnecessary flushing of the PMKSA cache entry and EAP
session data when processing SET_NETWORK commands that set a network
profile parameter to the same value that the parameter already has.
Introduce a new wpa_config_set() and wpa_config_set_quoted() return
value (==1) signifying that the new value being set for the
corresponding field equals to the already configured one so that the
caller can determine that nothing changed in the profile.
For now, this does not cover all the network profile parameters, but
number of the most commonly used parameters are included to cover the
Android use cases where the framework may have issued SET_NETWORK
commands that would have unnecessarily prevented use of PMKSA caching or
EAP fast reauthentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This patch add functionality of mesh SAE PMKSA caching. If the local STA
already has peer's PMKSA entry in the cache, skip SAE authentication and
start AMPE with the cached value.
If the peer does not support PMKSA caching or does not have the local
STA's PMKSA entry in the cache, AMPE will fail and the PMKSA cache entry
of the peer will be removed. Then STA retries with ordinary SAE
authentication.
If the peer does not support PMKSA caching and the local STA uses
no_auto_peer=1, the local STA can not retry SAE authentication because
NEW_PEER_CANDIDATE event cannot start SAE authentication when
no_auto_peer=1. So this patch extends MESH_PEER_ADD command to use
duration(sec). Throughout the duration, the local STA can start SAE
authentication triggered by NEW_PEER_CANDIDATE even though
no_auto_peer=1.
This commit requires commit 70c93963ed
('SAE: Fix PMKID calculation for PMKSA cache'). Without that commit,
chosen PMK comparison will fail.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This extends the wpa_supplicant PMKSA_FLUSH control interface command to
allow the PMKSA list from the authenticator side to be flushed for AP
and mesh mode. In addition, this adds a hostapd PMKSA_FLUSH control
interface command to flush the PMKSA entries.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This extends the wpa_supplicant PMKSA control interface command to allow
the PMKSA list from the authenticator side to be listed for AP and mesh
mode. In addition, this adds a hostapd PMKSA control interface command
to show the same list for the AP case.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This allows a mesh peer connection to be initiated manually in
no_auto_peer mesh networks.
Signed-off-by: Natsuki Itaya <Natsuki.Itaya@jp.sony.com>
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This command allows the specified mesh peer to be disconnected.
Signed-off-by: Natsuki Itaya <Natsuki.Itaya@jp.sony.com>
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
The bssid and priority parameters in a network block do not have any
effect on the validity of an EAP session entry, so avoid flushing the
cached session when only these parameters are changed. This is mainly to
allow forced roaming or network selection changes without causing fast
reauthentication to be disabled if the changes are done during RSN
association that used EAP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The existing implementation in p2p_ctrl_set used a hard-coded operating
class 81 which is only suitable for the social channels in the 2.4 GHz
band, and will not work for the social channel in the 60 GHz band.
Extend this by adding an optional op_class argument to P2P_SET
listen_channel. If not specified, use the default value of 81 to match
existing behavior.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
"INTERFACES ctrl" can now be used to fetch a list of network interfaces
and their control interfaces, e.g., to fetch the UDP port information
for the control interface.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Add an option to configure a candidate list to BSS transition query
("list" as the second argument to WNM_BSS_QUERY). The candidate list is
built from the available scan results. If no updated scan results (< 10
sec) are available, the command fails.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Remove the fallback dependency on os_random() when generating a WPS pin.
This is exceptionally unlikely to ever be called as the call to
os_get_random() is unlikely to fail. The intention is to facilitate
future removal of os_random() as it uses a low quality PRNG.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Ensure that characters are represented as unsigned char when using
isblank() and isspace(). These function take in a "int c" argument, but
it needs to be unsigned for the cases where EOF is not indicated.
Signed-off-by: Roy Marples <roy@marples.name>
This is needed to get proper P2P group removal processing for some test
cases. discovery_group_client followed by nfc_p2p_client was able to hit
a case where the P2P group idle timeout survived to the next group
instance because of the FLUSH command not clearing the group and this
timeout properly.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the FLUSH command to trigger auto connect mechanism
to schedule a new scan in 100 ms. This is not desired since all the
network profiles will be removed immediately and the scan or an attempt
to reconnect would not be of any benefit here. Such a scan in 100 ms can
cause issues for cases where multiple test sequences are run back to
back, so prevent this by clearing wpa_supplicant state to DISCONNECTED
(which avoids scheduling of the 100 ms scan trigger on disconnection) if
the state was AUTHENTICATING or higher when the FLUSH command was
issued.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wps_force_{auth,encr}_types parameters can be used in test build
(CONFIG_WPS_TESTING) to force wpa_supplicant to use the specified value
in the Authentication/Encryption Type flags attribute. This can be used
to test AP behavior on various error cases for which there are
workarounds to cover deployed device behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new optional ssid=<hexdump> argument to P2P_CONNECT can be used to
make P2P Client operations during join-an-existing-group more robust by
filtering out scan results based on the SSID in addition to the P2P
Device/Interface Address. This can help if the same MAC address has been
used in multiple groups recently and the cached scan results may still
include an older BSS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
At least one of the wpas_p2p_connect() callers (NFC join case) already
had access to the Group SSID. Pass that information through
wpas_p2p_connect() to wpas_p2p_join() so that the join operation can
filter out incorrect groups more easily.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a new command based Hotspot 2.0 icon retrieval option.
In short, here is the new command sequence:
1. REQ_HS20_ICON <bssid> <file-name>
2. event: RX-HS20-ICON <bssid> <file-name> <size>
3. GET_HS20_ICON <bssid> <file-name> <offset> <size>
(if needed, repeat with larger offset values until full icon is
fetched)
5. DEL_HS20_ICON <bssid> <file-name>
REQ_HS20_ICON is a new command that is analogous to HS20_ICON_REQUEST
with the slight difference that an entry to store the icon in memory is
prepared. The RX-HS20-ICON event has been augmented with BSSID,
file-name and size, and GET_HS20_ICON is used to retrieve a chunk of up
to <size> bytes of icon data at offset <offset>. Each chunk is returned
as a base64 encoded fragment, preceded by "HS20-ICON-DATA", BSSID, and
file-name as well as the starting offset of the data.
If there is no entry prepared for the icon when the ANQP result comes
back, hs20_process_icon_binary_file falls back to legacy behavior.
Finally the DEL_HS20_ICON command deletes (all) icons associated with
BSSID and file-name (there could be several if retries are used and they
have different dialog tokens).
Signed-off-by: Jan Nordqvist <jannq@google.com>
SIGNAL_MONITOR THRESHOLD=DD HYSTERESIS=DD command will request signal
strength monitoring events based on there having been requested amount
of drop in the signal strength. The threshold value is the RSSI
threshold in dBm for the event to be sent. 0 threshold can be used to
disable monitoring. The hysteresis value is RSSI hysteresis in dB to
specify the minimum amount of change before a consecutive event is
reported.
With nl80211 driver interface, these values map to the
NL80211_CMD_SET_CQM command with NL80211_ATTR_CQM_RSSI_THOLD and
NL80211_ATTR_CQM_RSSI_HYST attributes to the driver.
This command cannot be used when bgscan module is in use since that
depends on being able to control the connection monitoring parameters.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
The new wpa_supplicant control interface command "TEST_ASSOC_IE
<hexdump>" can now be used to override the WPA/RSN IE for Association
Request frame and following 4-way handshake to allow protocol testing of
AP side processing of WPA/RSN IE.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new methods are
1. VendorElemAdd "i" "ay" i=integer ay=array of bytes
2. VendorElemGet "i" i=integer (output array of bytes)
3. VendorElemRem "i" "ay" i=integer ay=array of bytes
These provide functionality similar to the control interface commands
VENDOR_ELEM_ADD, VENDOR_ELEM_GET, and VENDOR_ELEM_REMOVE.
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
Signed-off-by: Purushottam Kushwaha <p.kushwaha@samsung.com>
Signed-off-by: Kyeong-Chae Lim <kcya.lim@samsung.com>
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
Signed-off-by: Dilshad Ahmad <dilshad.a@samsung.com>
[VendorElemGet to return array of bytes instead of string; cleanup]
Signed-off-by: Jouni Malinen <j@w1.fi>
This may speed up some hwsim test case sequencies by avoiding a wait for
a scan at the end of a test case to complete.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new max_oper_chwidth and freq2 arguments to P2P_CONNECT, P2P_INVITE,
and P2P_GROUP_ADD control interface commands can be used to request
larger VHT operating channel bandwidth to be used than the previously
used maximum 80 MHz.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Some drivers do not support having two station interfaces, so the fact
that wpa_supplicant always creates a new interface in station mode, even
if it will be used as another type of interface, may prevent
wpa_supplicant from creating new interfaces. Allow setting the interface
type when a new interface is created so that interfaces of supported
types can be created.
Currently supported types are station ("sta") and AP ("ap"). If the
interface type is not specified, a station interface will be created.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
The AP is not expected to send out a WNM-Sleep Mode Response frame
without the STA trying to use WNM-Sleep Mode. Drop such unexpected
responses to reduce unnecessary processing of the frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
Vendor specific IEs added to frame type P2P_ASSOC_RESP are saved in
the interface context, but as they are added as part of the P2P IEs,
they need to be saved in the global P2P context.
Fix this by directing vendor specific IEs added to P2P_ASSOC_RESP
frame type to the P2P context.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
On successful P2P PD, report the chosen frequency in case the local
device is going to be the P2P GO, so in can later be used to instantiate
the new P2P GO, etc.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This allows wpa_supplicant to expose internally unknown ANQP-elements in
the BSS command. For example, "ANQP_GET <BSSID> 265" can be used to
fetch the AP Geospatial Location ANQP-element and if the AP has this
information, the "BSS <BSSID>" command will include the response as
"anqp[265]=<hexdump>".
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commands like BSS and GET_NETWORK are used in some cases very frequently
and those can increase the amount of debug information from
wpa_supplicant without significant benefit. These were logged at the
DEBUG level (-d). Move logging of such read-only commands (i.e., no new
wpa_supplicant operation is started based on it) to EXCESSIVE level
(-ddd) which was already used for the PING command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the BSS command returned an error if the WSC IE(s) in scan
results could not be parsed. This may be not ideal for all cases, to
instead of rejecting the command completely, return all other
information apart from the WPS information in such a case.
Signed-off-by: Jouni Malinen <j@w1.fi>
The P2P group is not yet operating when going through invitation
exchange for re-invocation. Previously, an old cached scan result could
be used to skip the scan immediately after the invitation exchange.
While this may result in the fastest possible connection, it does have
some issues with cases where the GO takes some time to start up. It
would also be at least theoretically possible for some of the BSS
parameters to be different, so having a fresh scan result from the new
GO instance may be desired in any case.
Add a mechanism to skip scan results that have been last updated before
a specific point in time and as the first user for this mechanism,
require chan results to be more recent than the invitation message
exchange for the P2P Client role in persistent group re-invocation case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When P2PS PD with default P2PS method is done, the peer that becomes GO
should authorize the client. However, P2PS specification doesn't require
the client to include its intended interface address in PD
Request/Response. As a result, the P2P Client's interface address may not
be known and any address may need to be authorized.
Previously, client's P2P Device Address was used for authorization,
which is not correct when a dedicated interface is used for P2P Client.
This is not resulting in a connection failure, however it causes a
significant delay (until WPS_PIN_TIME_IGNORE_SEL_REG elapses). Fix this
by authorizing the intended interface address, if known; or any address,
if not known.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Change P2PS P2P-PROV-SHOW-PIN/P2P-PROV-ENTER-PIN event notifications
on PD Request/Response handling to meet required P2PS behavior.
The new implemented scheme:
1. For a legacy P2P provision discovery the event behavior remains
without changes
2. P2PS PD, advertiser method: DISPLAY, autoaccept: TRUE:
Advertiser: SHOW-PIN on PD request replied with a status SUCCESS
Seeker: ENTER-PIN on PD response received with a status SUCCESS
3. P2PS PD, advertiser method: DISPLAY, autoaccept: FALSE:
Advertiser: SHOW-PIN on PD request replied with a status
INFO_CURRENTLY_UNAVAILABLE
Seeker: ENTER-PIN on Follow-on PD request with a status
SUCCESS_DEFERRED
4. P2PS PD, advertiser method: KEYPAD, autoaccept: TRUE/FALSE:
Advertiser: ENTER-PIN on PD request replied with a status
INFO_CURRENTLY_UNAVAILABLE
Seeker: SHOW-PIN on PD response received with a status
INFO_CURRENTLY_UNAVAILABLE
This change in behavior breaks the existing test cases
p2ps_connect_keypad_method_nonautoaccept and
p2ps_connect_display_method_nonautoaccept. Those will be fixed in a
followup commit.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
P2P_FLUSH command did not cleanly clear the p2p_go_avoid_freq data
structure, and left it in an inconsistent state, where the range field
was NULL but the num field was not 0. This would have resulted in an
invalid memory access in freq_range_list_includes().
Fix this.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
A P2P GO channel switch should not be triggered in all cases that
require channel list update. Specifically, a P2P GO CS should not
be triggered in case that the P2P GO state changed or in case that
that the P2P GO has just completed a CS.
To fix this, add reason code to wpas_p2p_channel_list_update() and
trigger CS flow only for the relevant cases.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This makes it possible to use these helper functions from hostapd as
well as the current use in wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend the QCA vendor specific nl80211 interface to query the preferred
frequency list from driver and add a new wpa_cli command to query this
information.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add vendor command to pass SET setband command to the driver and read
the updated channel list from driver when this notification succeeds.
This allows the driver to update its internal channel lists based on
setband configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a parameter allowing to specify a value of Coordination
Protocol Transport to P2PS_PROVISION and P2PS_PROVISION_RESP commands.
Extend the p2ps_provision structure to contain cpt_priority and
cpt_mask properties and initialize them on a P2PS PD request command.
The format of the parameter:
cpt=<cpt>[:cpt]
where <cpt> is CPT name e.g. UDP or MAC. The CPT names are listed
according to their preferences to be used for a specific P2PS session.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Add Coordination Transport Protocol parameter to P2P_SERVICE_ADD
asp command.
Extend p2ps_advertisement structure to contain CPT priorities
and a supported CPT bitmask.
The format of the new parameter:
cpt=<cpt>[:<cpt>]
where <cpt> is a name of the Coordination Protocol Transport.
This implementation supports two CPT names: UDP and MAC.
The order of specified CPTs defines their priorities where
the first one has the highest priority.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Do not allow wpa_s->fst to be replaced when processing FST-ATTACH
command for an interface that has already been attached.
Signed-off-by: Jouni Malinen <j@w1.fi>
This header file is needed to get struct fst_iface_cfg and struct
fst_wpa_obj defined. While it does currently get pulled in through
ap/hostapd.h and ap/ap_config.h, a more explicit inclusion may be a
cleaner option for future.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This command allows network variables to be copied from one network to
another when the networks belong to different radios. This is similar to
the per-interface DUP_NETWORK command. On the global control interface,
the command syntax is as follows:
DUP_NETWORK <src ifname> <dst ifname> <src network id> <dst network id> <variable name>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The IPv4 header after the Ethernet header is not 32-bit aligned and the
previous version ended up accessing 32-bit members at misaligned
addresses.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new TEST_FAIL and GET_FAIL control interface commands can be used
similarly to the earlier TEST_ALLOC_FAIL/GET_ALLOC_FAIL design. The new
version is more generic framework allowing any function to be annotated
for failure testing with the TEST_FAIL() macro. This mechanism is only
available in builds with CONFIG_WPA_TRACE_BFD=y and
CONFIG_TESTING_OPTIONS=y. For other builds, the TEST_FAIL() macro is
defined to return 0 to allow the compiler to remove the test code from
normal production builds.
As the first test site, allow os_get_random() to be marked for failing
based on call backtrace.
Signed-off-by: Jouni Malinen <j@w1.fi>
In p2p_find command line processing a loop searching for multiple
'seek=' parameters modifies cmd buffer adding '\0' terminators.
The 'freq=' parameter is handled after that and can be
lost if a 'freq=' follows 'seek=' in a command line.
Fix it by moving a handling of 'freq=' parameter to be processed
before 'seek=' handling loop.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
p2p_ctrl_group_add() takes care of various configuration options (such
as ht/vht) before calling wpas_p2p_group_add(), so use it (just like
when P2P_GROUP_ADD is called with additional params).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Parse each parameter individually and combine all the function calls.
This will allow further patch to call it with no parameters (currently
this might result in failure).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Only the first seek=<service name> parameter was accepted from the
P2P_FIND command. Fix this to go through all seek parameters to
construct the list of service hash values to seek.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This fixes some issues where a disconnection event may get ignored if an
earlier operation to remove or disable a network resulted in an attempt
to disconnect event though no connection was in place.
wpa_s->current_ssid != NULL alone is not sufficient to determine that
there will be a driver event notifying completion of such disconnection
request. Set own_disconnect_req to 1 only if wpa_s->wpa_state is also
indicating that there is a connection or an attempt to complete one.
This showed up in a failure, e.g., when running the hwsim test case
scan_int followed by ap_vlan_wpa2_psk_radius_required where the latter
ended up not processing a connection failure event and getting stuck not
trying to run a new scan and connection attempt.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Support a request to scan specific SSIDs given by user with the SCAN
command. The SSID list can be suffixed to the scan command as follows.
For example, if SSIDs "ABC" and "abc123" need to be specifically
scanned, the command should be "SCAN ssid 414243 ssid 616263313233". The
value of the SSID is passed in hexadecimal representation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add the TDLS_LINK_STATUS command to the control interface. This command
shows what is the status of our current TDLS connection with the given
peer. Also, add the TDLS_LINK_STATUS command to wpa_cli.
Signed-off-by: Oren Givon <oren.givon@intel.com>
By analysing objdump output some read only structures were found in
.data section. To help compiler further optimize code declare these
as const.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
This makes source code more consistent. The use within Android driver
interface is left as-is to avoid changes in the old PNO interface
definition.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This fixes a regression caused by commit
efa232f915 ('Add support for virtual
interface creation/deletion') for the case where an empty extra argument
is included.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Extend interface_add and interface_remove commands via an optional
argument to allow wpa_supplicant to create/delete a new virtual
interface.
Signed-off-by: Jithu Jance <jithu@broadcom.com>
Old code defaulted to WEP for an AP advertising OSEN. Show as OSEN
instead. Re-use most of the RSN parsing logic since all but the header
is the same.
Example output:
[root@ath9k-f lanforge]# ./local/bin/wpa_cli -i sta0 scan_results
bssid / frequency / signal level / flags / ssid
00:0e:8e:6f:40:49 2462 -23 [OSEN-OSEN-CCMP][ESS] ben-138
Signed-off-by: Ben Greear <greearb@candelatech.com>
If all networks are temporarily disabled, delay AP selection until at
least one network is enabled. Running AP selection when all networks are
disabled is useless as wpa_supplicant will not try to connect. In
addition, it will result in needless scan iterations that may delay the
connection when it is needed.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Extend p2p_service_del asp command to support 'all' parameter to delete
all ASP service advertisements.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reject external scan request while either ANQP fetch or Interworking
select is in progress. Not doing so could lead to a situation in which
Interworking automatic network selection does not get triggered because
of a new scan result event forcing the ANQP fetch cycle to be disrupted
and restarted all over again. Interworking automatic network selection
is only triggered when AQNP fetch cycle, that is, ANQP exchange with
every Interworking capable BSS in the current BSS list, is completed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant_deinit_iface() ends up removing all P2P groups if the
removed interface is the parent interface. This is correct behavior in
general, but this resulted in issues in the new group interface
initialization error path since wpa_s->parent was not assigned before
hitting this check. Fix this by assigning wpa_s->parent as part of
wpa_supplicant_add_iface().
Signed-off-by: Jouni Malinen <j@w1.fi>
There are number of cases where wpa_supplicant requests the current
connection to be disconnected before starting a new operation. Such
cases do not really indicate that there was an error in connecting or a
disconnection initiated by the AP, so do not add a temporary blacklist
entry in such sequences.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible for the P2P_CONNECT control interface command to be
issued on an incorrect interface. While the upper layer component should
really use global control interface for this, make this work by
redirecting the command to the correct context if needed.
Signed-off-by: Jouni Malinen <j@w1.fi>
The optional freq=<MHz> can now be used with the P2P_FIND command to
specify a single channel to scan during the first round of P2P search.
For example, this can be used to replace the full initial scan with a
single channel scan of a known operation channel.
Signed-off-by: Daichi Ueura <daichi.ueura@sonymobile.com>
These values were previously used only for sorting the scan results, but
it may be useful to provide access to the used values through the BSS
entries.
Signed-off-by: Jouni Malinen <j@w1.fi>
In addition, add support for returning the capability list through
the BSS control interface command.
Signed-off-by: ASHUTOSH NARAYAN <ashutoshx.narayan@intel.com>
In addition, add support for returning the capability list through the
BSS control interface command.
Signed-off-by: ASHUTOSH NARAYAN <ashutoshx.narayan@intel.com>
The new "DUMP" and "SET <variable>" control interface commands can be
used to fetch global wpa_supplicant configuration parameters.
Signed-off-by: Ola Olsson <ola.olsson@sonymobile.com>
This can be used to provide more control to upper layers on network
blocks generated as part of Interworking network selection.
INTERWORKING_ADD_NETWORK behaves otherwise identically to
INTERWORKING_CONNECT, but it does not request a new connection after
having added the network block and it returns the network id of the
added network.
INTERWORKING_ADD_NETWORK followed by REASSOCIATE would behave more or
less identically to INTERWORKING_CONNECT, but this allows the created
network profile to be modified, if desired, and/or stored externally.
SELECT_NETWORK can also be used with the network id returned from
INTERWORKING_ADD_NETWORK to enforce that specific network profile to be
used for the next connection (though, it should be noted that this
behavior may not meet all Hotspot 2.0 requirements if there were other
enabled networks that could have higher priority).
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit b31be3a0fd ('P2P: Add automatic GO
Negotiation vs. join-a-group selection') added this P2P_CONNECT 'auto'
parameter, but did not update any documentation on it.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 07cb45ccb2 ('mesh: Add no_auto_peer
config option') added a new struct wpa_ssid argument and added an
unnecessary parsing and setting of the value in
wpa_supplicant_ctrl_iface_update_network(). This is not needed since
wpa_config_set() takes care of parsing the parameters.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible for a network profile to change its type from P2P
persistent group to a normal network and back. The D-Bus interface uses
different types of objects for those, so the object needs to
re-registered in case of type change. This fixes issues in leaving
behind an incorrect type of object and leaking memory when freeing such
a network block that has had its disabled parameter changed.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is needed to allow P2PS related new control interface commands to
be redirected for proper context processing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This introduces a P2P module callback function that will be used to
create the pending P2PS group after sending PD Response and receiving
ACK status for it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds new wpa_supplicant control interface commands
P2P_ASP_PROVISION and P2P_ASP_PROVISION_RESP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends wpas_p2p_prov_disc() implementation to accept P2PS
parameters. None of the callers are yet using this functionality; the
following commit introduces a user.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the P2P_SERV_DISC_REQ control interface command with a new
"asp" service type. This takes service id, service string, and optional
service info as arguments.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In addition, add a new P2P_SERVICE_REP command that can be used to
replace existing ASP advertisements.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This provides additional WPS definitions and rules for negotiating use
of P2PS default PIN configuration method.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
P2PS seek strings can now be specified in the P2P_FIND control interface
command with one or more optional "seek=<str>" parameters.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends GET_CAPABILITY command to allow the supported group
management frame cipher suites to be listed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
A control interface call to flush the current state used the
current wpa_s to clear the P2P state even though it might not
be the interface controlling the P2P state.
Fix it by using the correct interface to flush the P2P state.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The length should be 14 and not 10.
The current situation causes failure during parsing of the command.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
For CONFIG_TESTING_OPTIONS=y builds, add a new test parameter than can
be used to trigger various error cases within wpa_supplicant operations
to make it easier to test error path processing. "SET test_failure
<val>" is used to set which operation fails. For now, 0 = no failures
and 1 = scan trigger fails with EBUSY. More operations can be added in
the future to extend coverage.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Move the wpa_bss_flush() call to the end of the function to allow any
pending user of a BSS entry to be cleared before removing the unused
entries. There were number of cases where BSS entries could have been
left in the list and this resulted in some hwsim test failures.
Signed-off-by: Jouni Malinen <j@w1.fi>
For Interworking connection to work, the SSID of the selected BSS needs
to be known to be able to associate with the AP. It was possible for the
scan results to include two BSS entries matching the BSSID when an
earlier scan with that AP has shown a hidden SSID configuration (e.g.,
when running hwsim test cases, but at least in theory, this could happen
with real use cases as well). When that happened, the incorrect BSS
entry may not have included RSN configuration and as such, it would get
rejected for Interworking connection.
Fix this by confirming that the selected BSS entry has a real SSID. If
not, try to find another BSS entry matching the same BSSID and use that,
if found with an SSID.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier for upper layer programs to figure out whether the
wpa_supplicant and and the driver supports mesh.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it easier for upper layer programs to figure out whether the
wpa_supplicant and and the driver supports SAE.
Signed-off-by: Jouni Malinen <j@w1.fi>
This new wpa_supplicant and hostapd control interface command can be
used to determine which TLS library is used in the build and what is the
version of that library.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new control interface command TEST_ALLOC_FAIL and GET_ALLOC_FAIL can
now be used to trigger memory allocation failures for testing purposes.
TEST_ALLOC_FAIL sets a failure conditions with
<count>:func[;func][;func]... string and GET_ALLOC_FAIL returns the
current state using the same format. Whenever an allocation is made with
a matching backtrace of calling functions, the count is decremented by
one and once zero is reached, the allocation is forced to fail.
Function names can be prefixed with either '=' or '?' to get different
matching behavior. '=' requires this specific function to be the next
one in the backtrace (i.e., do not skip any other functions in the list
which is the default behavior). '?' allows the function to be optionally
present in the backtrace.
Signed-off-by: Jouni Malinen <j@w1.fi>
The supplicant code does not try to control the actual channel of the
radio at any point. It simply passes the target peer and channel
parameters to the driver. It's the driver's responsibility to
periodically initiate TDLS channel-switch operations when TDLS
channel-switching is enabled.
Allow enable/disable operations to be invoked via the control interface.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
It was possible for old scan state to remain from a previous test case
when an operation like WNM neighbor scan or another-BSS-in-ESS was
started, but stopped at the end of a test case. This could result in
failures, e.g., when running wnm_bss_tm_req followed by scan_setband.
Signed-off-by: Jouni Malinen <j@w1.fi>
This helps hwsim test cases by avoiding undesired state from previously
executed test cases affecting following tests.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit faf9a8585d added mechanism for
selecting 2.4 or 5 GHz band for scan operation. However, no mechanism
for setting the setband value was added at that time. This commit adds a
new SET ctrl_iface parameter to allow the setband functionality to be
used. "SET setband <AUTO/5G/2G>" can be used to select all bands, 5 GHz
band only, or 2.4 GHz band only.
Signed-off-by: Jouni Malinen <j@w1.fi>
FAIL-BUSY was already returned for the case where a scan had been
started, but with the radio work design, it would have been possible to
schedule multiple scan requests if a non-scan radio work was in
progress. Multiple back-to-back scans are not usually very helpful, so
reject this type of cases where the SCAN command would be used to build
such a sequence.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The mesh gate is used to bridge (or route) between mesh network and
another network. For example, mesh gate acts as router between mesh
network and IEEE 802.11 BSS network.
This command makes a virtual mesh interface to be used for mesh gate.
This command expects to be used like this.
wpa_cli -i wlan0 MESH_INTERFACE_ADD ifname=mesh0
wpa_cli -i mesh0 add_network
wpa_cli -i mesh0 set_network 0 ssid '"commell_2X_mmm"'
wpa_cli -i mesh0 set_network 0 mode 5
wpa_cli -i mesh0 set_network 0 frequency 2412
wpa_cli -i mesh0 set_network 0 key_mgmt SAE
wpa_cli -i mesh0 set_network 0 psk '"01234567"'
wpa_cli -i mesh0 mesh_group_add 0
wpa_cli -i wlan0 mesh_group_remove mesh0
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This function could not fail and it can be replaced with a single
line variable update that takes less code than the function call.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_bss_flush*() cannot fail and as such, there is no need for
wpa_supplicant_ctrl_iface_bss_flush() to return a value either.
Signed-off-by: Jouni Malinen <j@w1.fi>
This function cannot return negative value, so no need to check for
that. If there is not enough room in the buffer or if something
unexpected happens, 0 is returned.
Signed-off-by: Jouni Malinen <j@w1.fi>
Update the scan parameters in wpa_s only in case the scan command is
going to be executed. In other words, do not change the parameters for
an ongoing scan (the SCAN command is rejected with FAIL-BUSY) or if any
of the parameters is invalid.
Signed-off-by: Jouni Malinen <j@w1.fi>
The space following the BSSID was not skipped properly if the following
parameter started with the "hs20:" prefix. For other cases, atoi() ended
up ignoring the space, but it is cleaner to skip it anyway for all
cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is needed to get into more consistent state after the FLUSH
command. DISCONNECT followed by FLUSH could result in
wpa_s->disconnected being left to 1 and this resulted in a test failure,
e.g., when running wpas_ctrl_dup_network followed by
wpas_ctrl_enable_disable_network where the latter was expecting
ENABLE_NETWORK on a disabled network to connect automatically and that
does not happen if wpa_s->disconnected == 1.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While these are using practically large enoungh buffer sizes, it is
better to be more consistent with checking os_snprintf() return value.
Signed-off-by: Jouni Malinen <j@w1.fi>
This converts os_snprintf() result validation cases to use
os_snprintf_error() for cases that were note covered by spatch and
semantic patches.
Signed-off-by: Jouni Malinen <j@w1.fi>
This converts os_snprintf() result validation cases to use
os_snprintf_error() in cases where success condition was used to execute
a step. These changes were done automatically with spatch using the
following semantic patch:
@@
expression E1,E2,E3;
statement S1;
@@
E1 = os_snprintf(E2, E3, ...);
- if (\( E1 >= 0 \| E1 > 0 \) && \( (size_t) E1 < E3 \| E1 < (int) E3 \| E1 < E3 \))
+ if (!os_snprintf_error(E3, E1))
S1
Signed-off-by: Jouni Malinen <j@w1.fi>
This pointer cannot be NULL sicne it is called only from this file and
with a valid pointer to the received command.
Signed-off-by: Jouni Malinen <j@w1.fi>
Derive rRK and rIK on EAP peer if ERP is enabled. The new wpa_supplicant
network configuration parameter erp=1 can now be used to configure the
EAP peer to derive EMSK, rRK, and rIK at the successful completion of an
EAP authentication method. This functionality is not included in the
default build and can be enabled with CONFIG_ERP=y.
If EAP authenticator indicates support for re-authentication protocol,
initiate this with EAP-Initiate/Re-auth and complete protocol when
receiving EAP-Finish/Re-auth.
Signed-off-by: Jouni Malinen <j@w1.fi>
This change creates 'LIST_NETWORK LAST_ID=x' form to allow
retrieval of all networks saved in the system. Without this form,
only first few (whatever fills in first 4096 bytes) can be
retrieved.
Signed-off-by: Vinit Deshpande <vinitd@google.com>
Externally triggered scan could result in a new radio work item getting
started even when external radio work was in progress. Delay such start
until the external work is completed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_supplicant control interface command can be used in
automated testing to verify how AP processes Data frames with arbitrary
contents. This is enabled only in builds with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need for this state to maintained when the wpa_supplicant
FLUSH ctrl_iface command is used to request flushing of all state.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow supplying an SSID for the SSID IE. If not supplied, no SSID IE is
sent, and the request implies the current SSID.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Add NEIGHBOR_REP_REQUEST command to the wpa_supplicant ctrl_iface.
This command triggers the sending of a Neighbor Report Request to the
associated AP.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
This wmm_ac_status command will show the current status for WMM AC.
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Android 4.4 uses "BSS" command instead of "SCAN_RESULT" command.
So this patch add the mesh scan result for BSS command.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Parse MESH_GROUP_ADD/REMOVE commands on ctrl interface and call
wpa_supplicant routines. These commands are used to start or
join and leave a mesh network.
The mesh id is given in the configuration file, therefore there is
no need to scan before joining a mesh network. We reuse the
connect_without_scan construct used by P2P for that same purpose.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Javier Lopez <jlopex@gmail.com>
This adds definitions for the 128-bit level Suite B AKM 00-0F-AC:11. The
functionality itself is not yet complete, i.e., this commit only
includes parts to negotiate the new AKM.
Signed-off-by: Jouni Malinen <j@w1.fi>
If p2p_stop_find is issued after the p2p_scan request is triggered to
the host driver, the obtained scan results are also considered to update
the P2P peer entries. This is not always desired behavior, i.e., it can
be clearer if no P2P-DEVICE-FOUND events are generated based of that
final pending scan.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use the 'no_ir' notation instead of the 'passive scan' and
'no_ibss' notations to match the earlier change in nl80211.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The extra_roc_dur parameter can now be used in CONFIG_TESTING_OPTIONS=y
builds to simulate driver behavior where the ROC duration gets increased
without user space request.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add no_auto_peer parameter, which controls wheter a station will
automatically initiate peering to another mesh peer that comes into
range.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
These key management options were missing from the previous set of
parsed information in scan results.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Abele <jason.abele@gmail.com>
