It was possible to hit a case where the SAE PT had not yet been derived,
e.g., when using P2P group re-invocation. Update PT use at the time
authentication is started, if needed, to avoid this. While this is not
really ideal from the externally observable timing view point, this is
done only for the case where there is no other option available with a
dynamically changing network configuration for P2P. Similar design was
already in place for the SAE offload-from-driver (external auth) case.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Both P2P GO and client always save key_mgmt = WPA_KEY_MGMT_PSK in the
configuration when storing a persistent group. Next time, when a GO is
started as an autonomous GO on a 6 GHz channel, it will change key_mgmt
to SAE and use hash-to-element mechanism, but the P2P client doesn't
change the parameter even if the group it wants to join is operating on
a 6 GHz channel. The P2P connection will be failed due to reason 'reject
due to mismatch with WPA/WPA2'.
Enable SAE-H2E for P2P client in this case.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Commit 3a0edb2cd8 ("SAE: Enable H2E for 6 GHz BSS") started enabling
H2E automatically for SAE use on the 6 GHz band, but it did not update
these steps in verifying whether the STA has matching configuration for
a BSS that mandates use of H2E and whether to use PT for SAE in SME.
Update these to be aware of automatic H2E enabling.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
ssid->ocv is defined within CONFIG_OCV block, so the use for it needs to
match.
Fixes: dc7e330e0b ("Set OCV capability based on Association Request frame RSNE")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Currently, OCV self-capability is being set into the RSN supplicant
state machine only during the initial connection and never getting
updated. But for the driver-SME cases the driver may enable/disable OCV
in (Re)Association Request frame RSNE based on the AP chosen to roam.
This will lead to missing synchronization between wpa_supplicant and the
driver. Thus, update OCV self-capability in the wpa_supplicant RSN state
machine based on the (Re)Association Request frame RSNE indicated in the
connect response.
Signed-off-by: Aleti Nageshwar Reddy <quic_anageshw@quicinc.com>
The check for PBC overlap on a partner link should not be done unless
the current interface is actually in active PBC mode. Furthermore, the
wpa_s->wps_overlap variable needs to be cleared in additional places to
avoid leaving it set indefinitely.
This was found with the following test case sequence:
dbus_wps_pbc_overlap dbus_p2p_two_groups
Fixes: b43e19f3f3 ("WPS: Cross band overlap detection with multiple interfaces")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Commit ace0fbdb69 ("P2P: Fix segfault when PBC overlap is detected")
removed the external calls to this function, but did not mark it static.
Mark it static now to clarify expected uses through the
wpas_p2p_pbc_overlap_cb() timer handler.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
There was a race condition between the NFC handover requester and
selector role processing that ended up not sending out the alternative
proposal in some cases. Catch those at the end of
run_dpp_handover_client() processing (or immediately after returning
from that function without having sent out the alternative proposal).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
IEEE Std 802.11ax-2021, 12.12.2 requires this, so force MFPR=1 when
associating on the 6 GHz band so that ieee80211w=1 (i.e., MFPC=1 MFPR=0)
configuration can be used to get MFPC=1 behavior on other bands and
MFPR=1 on the 6 GHz band.
Signed-off-by: Jouni Malinen <j@w1.fi>
Allow specifying preferred GO band in addition to frequency. If a band
is specified, the first two scans will be limited to only non-DFS
channels to shorten scan times, and the next two will scan the entire
band.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
Now that we check in PMKSA cache code whether the entry was created for
the same local address, it is fine to leave the old entries in the cache
even if we have changed addresses. This allows a valid PMKSA cache entry
to be used when restoring the same MAC address for the same ESS.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the implementation more readable by sharing the same set of
enum values for all the parameters related to what kind of random MAC
addresses are used.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_s->last_mac_addr_change.sec might be zero in the special case of UML
testing with time travel since it would be possible to complete the test
case steps within one second of the system start.
Signed-off-by: Jouni Malinen <j@w1.fi>
When MAC address randomization settings change we should use a new MAC
address even if we are associating to the same ESS.
For example, consider this scenario:
- hardware MAC is being used,
- we disconnect from the network,
- policy/style is changed via D-Bus to turn randomization on,
- we reconnect to the same network.
In the last step a randomized MAC address should be used.
Changes to the randomization settings include both changes to the
policy/style to be used and changes to the pregenerated MAC address
value in case of mac_addr==3.
Signed-off-by: Andrzej Ostruszka <amo@semihalf.com>
If the CreateInterface command was used to create a virtual AP
interface, deleting this interface using the RemoveInterface command was
also bringing down the primary interface.
wpa_supplicant never uses hostapd style multi-BSS setup with
type=WPA_IF_AP_BSS and setup_ap=1 to if_add() when creating an AP
interface in wpa_driver_nl80211_if_add(), so it should not go through
the multi-BSS tear down procedure in wpa_driver_nl80211_if_remove(). The
virtual AP resources init and deinit are well handled in
wpa_driver_nl80211_init() and wpa_driver_nl80211_deinit().
Collapse the interface type to WPA_IF_STATION for the D-Bus interface to
skip the multi-BSS cleanup procedure. This is inline with the control
interface design. Add comments before the code to avoid confusion.
Signed-off-by: Jintao Lin <jintaolin@chromium.org>
The driver is expected to translate the link addresses to MLD addresses
when processing an Authentication frame from a MLD AP. Thus, accept
Authentication frame when the peer matches the expected MLD address.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
In case both the local driver and the AP support MLD, request an MLD
association from the driver.
When processing the association event from the driver verify that the
multi link information in the (Re)Association Response frame ML element
matches the links on which the association was expected.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
In case both the local driver and the AP support MLD, request an MLD
authentication from the driver. When processing the authentication event
from the driver verify that the MLD address in the authentication data
matches that of the requested AP.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Authentication frames include several fixed body parts (see Table 9-68
(Authentication frame body) and Table 9-69 (Presence of fields and
elements in Authentication frames) in IEEE P802.11-REVme/D2.0).
To be able to parse the IE part, these fields need to be skipped. Since
SAE logic already implements this parsing, change SAE authentication
handling functions to return the offset to the IE part. This preparation
is needed for future MLD patches that need to parse out the ML related
elements in the Authentication frames.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
In case of drivers that offload the 4-way handshake to the driver, there
was no way of updating wpa_supplicant about the transition disable
bitmap received as a part of EAPOL-Key msg 3/4.
With latest provisions in cfg80211_port_authorized(), the TD bitmap can
be sent to the upper layer. Parse that as a part of the port authorized
event and set the transition disable information accordingly.
Signed-off-by: Vinayak Yadawad <vinayak.yadawad@broadcom.com>
chromeOS uses random generated MAC address for AP interface so that the
device could remain anonymous and untrackable. Add an address parameter
for CreateInterface method to pass in OS managed MAC address.
Signed-off-by: Jintao Lin <jintaolin@chromium.org>
Fix a potential memory leak in CreateInterface method.
Fixes: 0ba266d86c ("dbus: Add virtual interface create/remove logic to be inline with ctrl_iface")
Signed-off-by: Jintao Lin <jintaolin@chromium.org>
RSNXE bits were modified, so update the relevant places accordingly.
Please note, WLAN_RSNX_CAPAB_PROT_RANGE_NEG was renamed to
WLAN_RSNX_CAPAB_URNM_MFPR and the bit position is changed to 15 instead
of 10, while BIT 10 is used for WLAN_RSNX_CAPAB_URNM_MFPR_X20 and is not
supported yet.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Check the HE membership selector and don't use the BSS
if required but not supported by HW.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add support to handle external authentication request with a different
SAE AKM suite compared to the current connection AKM suite. This is
needed to support cross AKM roaming between SAE and SAE-EXT-KEY AKM
suites.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
PASN deauthentication event is sent by the underlying driver to delete
the keys in wpa_supplicant PTKSA cache. So don't send clear secure
context command to the driver again as it is already aware of it.
Fixes: 74d894a2 ("PASN: Offload handshake for multiple peers from the driver")
Signed-off-by: Vinay Gannevaram <quic_vganneva@quicinc.com>
Though not explicitely forced by IEEE 802.11be draft yet, it makes sense
to apply the same logic for MLD as for 6 GHz BSSs. Change
wpa_supplicant_ssid_bss_match() accordingly.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
MAX_NUM_MLD_LINKS is 15, thus u8 isn't enough for the bitmap. Fix it.
While at it, clean MLO information better.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add the required ML and RNR definitions and report the information in
BSS command.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Allows informing the connection manager of additional information on CQM
events. Allows the connection manager to request the same information
on demand by using the existing "SignalPoll" method.
* Add new property "SignalChange"
* Add storage for wpa_signal_info into wpa_supplicant context
object
* Copy memory from event to context object on CQM Event
* Write a common conversion method to be used by both "SignalPoll" and
this property
Signed-off-by: David Ruth <druth@chromium.org>
Facilitate emitting more station information over D-Bus for use by the
connection manager.
* Add storage for more NL80211_STA_INFO_* fields to data structures, and
move them through the system.
* Reorder NL80211_STA_INFO_* fields in driver_nl80211.c to match the
ordering in nl80211.h.
* Convert signal field to an integer to support holding WPA_INVALID_NOISE
and avoid changing logging.
* Add fields to hostap_sta_driver_data to capture more information
* fcs_error_count
* beacon_loss_count
* expected_throughput
* rx_drop_misc
* rx_mpdus
* rx_hemcs
* tx_hemcs
* rx_he_nss
* tx_he_nss
* avg_signal
* avg_beacon_signal
* avg_ack_signal
* Add struct hostap_sta_driver_data to struct wpa_signal_info and remove
redundant fields and redundant attribute parsing
* Change logging when printing txrate to handle unsigned long
value
Signed-off-by: David Ruth <druth@chromium.org>
Since wpa_supplicant can change MAC address of the interface on its own
(with randomization enabled) it makes sense to introduce MACAddress as a
property of the interface and send notifications about its change.
This allows other applications to just use D-Bus instead of both
communicating over D-Bus with wpa_supplicant and listening to Netlink
notifications for MAC changes.
Signed-off-by: Andrzej Ostruszka <amo@semihalf.com>
Add support to consider EHT rates while calculating the estimated
throughput for scan results.
- The estimated EHT throughput uses the HE 0.8 usec GI rates from the
relevant EHT-MCS tables from IEEE P802.11be/D2.0, 36.5.
- The minimum SNR values for EHT rates (4096-QAM) are derived by adding
the existing minimum SNR values of 1024-QAM rates from HE tables and
the difference between the values of minimum sensitivity levels of
1024-QAM rates and 4096-QAM rates defined in Table 36-67 (Receiver
minimum input level sensitivity) in IEEE P802.11be/D2.0.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
There are several cases where memory allocations are not
checked for success. Add conditions and error messages, as some
analyzers complain about that.
Signed-off-by: Micha Hashkes <micha.hashkes@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Even if the use of H2E isn't strictly mandatory when using SAE on 6 GHz,
WPA3-Personal pushes it on 6 GHz, so enable H2E automatically when
connecting to a BSS on the 6 GHz band if it was not enabled in the
configuration.
Signed-off-by: Jimmy Chen <jimmycmchen@google.com>
When WPS is running simultaneously on multiple per-band radios (e.g., a
separate 2.4 GHz and 5 GHz band radios in an AP device), handle
synchronization of scan results, detect PBC session overlap, and cancel
WPS for enrollees on both interface, if the UUID of the registrars on
different bands differ.
Signed-off-by: Sai Pratyusha Magam <quic_smagam@quicinc.com>
Just like with WPA-PSK and keyids it may be desired to identify
connecting clients to provide additional network filtering.
This does:
- extend DPP_EVENT_AUTH_SUCCESS to expose public
key hash of the peer so the system can pick it
up and use for identification later
- store public key hash in PMKSA from DPP Network
Intro for later use
- extend sta mib to print out the dpp_pkhash
from PMKSA if present
- extend AP_STA_CONNECTED to include the
dpp_pkhash from PMKSA if present
Signed-off-by: Michal Kazior <michal@plume.com>
This event is generated in a couple of places. It'll be easier to extend
the event with additional metadata if it's generated in a single place.
Signed-off-by: Michal Kazior <michal@plume.com>
On NixOS[1] - a Linux distribution which allows to configure a full OS
declaratively - it's possible to configure SSIDs for `wpa_supplicant`
like this:
networking.wireless.networks = {
myssid = {
pskRaw = "<redacted>";
};
};
It's also possible to add networks "imperatively" using `wpa_gui` or
`wpa_cli`. However it's not possible to do both because if the first
option is used, NixOS creates a read-only symlink at
`/etc/wpa_supplicant.conf` and then it's not possible for
`wpa_supplicant` anymore to write to it.
This patch aims to help us changing this: while "declarative" SSID
configuration can be quite useful, it's a bad idea for e.g. sensitive
stuff like a WPA2 enterprise network.
The original idea was to use `-I`[2] for immutable configs (including
"declarative" networks) on NixOS and `-c /etc/wpa_supplicant.conf` for
anything "imperative".
However this doesn't really work out because if a wifi network from a
config file specified with `-I` is changed by e.g. `wpa_gui`, it's
silently overwritten in `/etc/wpa_supplicant.conf` (specified with
`-c`) which is IMHO unintuitive (in our case at least). This patch
basically declares each network defined in a config file passed via `-I`
to `wpa_supplicant` as "read-only" and doesn't write these "read-only"
networks to `/etc/wpa_supplicant.conf`.
A bit more context can be found on GitHub in the PR where I implemented
this[3].
[1] https://nixos.org/
[2] Added in e6304cad47
[3] https://github.com/NixOS/nixpkgs/pull/113716
Signed-off-by: Maximilian Bosch <maximilian@mbosch.me>
Add new 'mac_addr' policy (3) with which supplicant expects to also
obtain 'mac_value' with pregenerated value of MAC address to be used for
given SSID.
The main difference between this policy and policy 1 is the ability to
control persistence of the MAC address used. For example if there is
a requirement to always use the same (but random) MAC address for given
SSID (even if user removes/forgets the network) this could be handled
outside of the wpa_supplicant by using some SSID based hashing scheme to
generate MAC (or by just storing the randomly generated one) and
providing it to wpa_supplicant together with mac_addr=3 policy.
Signed-off-by: Andrzej Ostruszka <amo@semihalf.com>
IEEE Std 802.11ax-2021, 12.12 explicitly disallows use of Open System
authentication without encryption on the 6 GHz band.
Signed-off-by: Sharadanand Karanjkar <skaranjkar@datto.com>
As P2P GOs are not expected to be collocated, i.e., they are not
expected to be announced in the RNR element of other APs, they can
operate only on preferred scanning channels (PSCs).
When performing a full scan for P2P discovery, include only the 6 GHz
PSCs (if supported) to avoid scanning channels on which P2P GOs are not
expected to reside.
While at it also fix couple of places that missed including 60 GHz
channels in P2P full scan.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add a callback handler to notify details of a PMKSA cache entry when it
is added to the PMKSA cache. This can be used to provide external
components more convenient access to the PMKSA cache contents.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
For WPA2/WPA3 authentication mode, wpa_supplicant needs to notify
CurrentAuthMode property change when wpa_s->key_mgmt changes, so
NetworkManager can judge whether it needs to request a password based on
this.
Call wpas_notify_auth_changed() when starting a new connection item,
i.e., after having updated wpa_s->key_mgmt.
Signed-off-by: xinpeng wang <wangxinpeng@uniontech.com>
SSID may include unprintable characters. This change converts
unprintable characters into printable form before printing SSID in the
function wpas_send_ctrl_req(). The conversion is based on the function
wpa_ssid_txt().
Signed-off-by: Kaidong Wang <kaidong@chromium.org>
In case of drivers supporting 4-way handshake offload, mark port
authorized and state completion only if the driver advertizes authorized
state in the connect event. Otherwise there are fair chances of the
driver port authorization API getting called while 4-way handshake is in
progress at the lower layer.
In order to avoid this possible race condition always update port
authorization and supplicant state WPA_COMPLETED setting from
EVENT_PORT_AUTHORIZED context when the driver is done with the 4-way
handshake.
Signed-off-by: Vinayak Yadawad <vinayak.yadawad@broadcom.com>
Add the support of multiple domains for interworking credentials in
D-Bus API AddCred() using an array of strings.
Signed-off-by: Damien Dejean <damiendejean@chromium.org>
Fix compilation issue when using the following build parameter:
CONFIG_CTRL_IFACE=udp-remote
Fixes: 0aae045af0 ("ctrl: Print the source address of the received commands")
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Until now Hotspot 2.0 credentials were only supporting one home OI (with
roaming_consortium option) and one required home OI (with
required_roaming_consortium option). To improve the compliance with
Passpoint specification, add the support for multiple home and required
OIs.
The lists of OIs are provided using two new configuration options
home_ois and required_home_ois that expect a list of OIs formatted as
the roaming_consortiums list. It allows to keep the old options to avoid
breaking currently running configurations and better fits the vocabulary
used in the spec.
The OI match algorithm is updated to implement the behavior described in
Passpoint specification v3.2 section 9.1.2 (Home OIs nodes description
PerProviderSubscription/<X+>/HomeSP/HomeOIList/<X+>).
Signed-off-by: Damien Dejean <damiendejean@chromium.org>
There is no way to create or remove a virtual interface with
wpa_supplicant dbus methods. The platform has to use out-of-band methods
to manage the virtual interfaces.
This change adds virtual interface create/remove logic to the dbus
methods CreateInterface and RemoveInterface to achieve similar
functionalities as wpa_cli commands interface_add and interface_remove.
Signed-off-by: Jintao Lin <jintaolin@chromium.org>
Need to copy own address and peer address locally and pass them to
pasn_deauthenticate(), because this pointer data will be flushed from
the PTKSA cache before sending the Deauthentication frame and these
pointers to then-freed memory would be dereferenced.
Fixes: 24929543 ("PASN: Deauthenticate on PTKSA cache entry expiration")
Signed-off-by: Vinay Gannevaram <quic_vganneva@quicinc.com>
Map to correct control interface commands for PASN start and stop.
Fixes: ad338cfe58 ("ctrl_iface: Add support for PASN authentication")
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
wpa_supplicant used the WPS IE from a Probe Response frame, if one was
received, even if there might have been a more recent Beacon frame with
an updated WPS IE. This could result in using stale information about
active WPS registrar, e.g., when operating on the 6 GHz band.
Prefer WPS IE from a Beacon frame over the default selection of Probe
Response frame (if one has been received) in cases where the Beacon
frame is received more recently than the Probe Response frame and active
WPS Registrar information is being checked. Skip this for the case where
UUID-E is needed since that is not available in the Beacon frame.
Signed-off-by: Sai Pratyusha Magam <quic_smagam@quicinc.com>
OCV cannot be used without PMF and such a configuration were to be used
with wpa_supplicant, the AP would reject the association. hostapd is
already enabling PMF automatically whenever OCV is being enabled, so do
the same with wpa_supplicant.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
If a higher priority BSS has invalid security parameters, e.g., an
invalid SAE password, and a lower priority BSS is discovered only after
the local network profile has been temporarily disabled, the BSSID
ignoring mechanism is not sufficient to allow the lower priority BSS to
be tried and all consecutive attempts will continue to use the higher
priority BSS. This might prevent connection in some unexpected cases
with invalid network configuration.
Extend BSSID ignoring mechanism to work in this type of a case by
ignoring the BSSID that resulted in disabling the SSID temporarily
during the first connection attempt after having re-enabled the SSID.
This allows a lower priority BSS, if any is available in scan results,
to be tried next to see if it might have working security parameters.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Fix memory leak of intro.peer_key in wpas_dpp_rx_peer_disc_resp(). The
other code paths were updated to use dpp_peer_intro_deinit(), but this
non-privacy-protection version of the station implementation was missed.
Fixes: 148de3e0dc ("DPP3: Private Peer Introduction protocol")
Signed-off-by: Glenn Strauss <gstrauss@gluelogic.com>
This is needed to avoid trying the subsequent connections with the old
PMKID that the AP claims not to hold and continues connection failures.
This was already handled for the SME-in-the-driver case in commit commit
50b77f50e8 ("DPP: Flush PMKSA if an assoc reject without timeout is
received"), but the wpa_supplicant SME case did not have matching
processing.
Add the needed check to avoid recover from cases where the AP has
dropped its PMKSA cache entry. Do this only based on the specific status
code value (53 = invalid PMKID) and only for the PMKSA entry that
triggered this failure to minimize actions taken based on an unprotected
(Re)Association Response frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
This prevents attempts of trying to use PMKSA caching when the existing
entry was created using a different MAC address than the one that is
currently being used. This avoids exposing the longer term PMKID value
when using random MAC addresses for connections.
In practice, similar restriction was already done by flushing the PMKSA
cache entries whenever wpas_update_random_addr() changed the local
address or when the interface was marked down (e.g., for an external
operation to change the MAC address).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is needed to be able to determine whether a PMKSA cache entry is
valid when using changing MAC addresses. This could also be used to
implement a mechanism to restore a previously used MAC address instead
of a new random MAC address.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Using separate variables for BSSID and peer address is needed to support
Wi-Fi Aware (NAN) use cases where the group address is used as the BSSID
and that could be different from any other peer address. The
infrastructure BSS cases will continue to use the AP's BSSID as both the
peer address and BSSID for the PASN exchanges.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Rename struct pasn_data::bssid to peer_addr to be better aligned with
different use cases of PASN and its extensions. This is a step towards
having option to use different peer address and BSSID values for NAN use
cases.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
wpa_supplicant has support for only a single FT key hierarchy and as
such, cannot use more than a single mobility domain at a time. Do not
allow FT protocol to be started if there is a request to reassociate to
a different BSS within the same ESS if that BSS is in a different
mobility domain. This results in the initial mobility domain association
being used whenever moving to another mobility domain.
While it would be possible to add support for multiple FT key hierachies
and multiple mobility domains in theory, there does not yet seem to be
sufficient justification to add the complexity needed for that due to
limited, if any, deployment of such networks. As such, it is simplest to
just prevent these attempts for now and start with a clean initial
mobility domain association.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
During cross SSID roaming wpa_supplicant ended up using the default
RSNE/RSNXE in EAPOL-Key msg 2/4 though the driver indicated
(Re)Association Request frame elements without RSNE/RSNXE. This causes
RSNE/RSNXE mismatch between (Re)Association Request frame and EAPOL-Key
msg 2/4.
To avoid this skip copying the default RSNE/RSNXE if the driver
indicates the actually used (Re)Association Request frame elements in
the association event.
Signed-off-by: Utkarsh Soni <quic_usoni@quicinc.com>
Passphrases/PSKs from external password databases were ignored if 4-way
handshake offloading was supported by the driver. Split the PSK loading
functionality into a separate function and calls if to get the PSK for
handshake offloading.
I tested connecting to a WPA2-PSK network with both inline and external
passphrases, using the iwlwifi and brcmfmac drivers.
Signed-off-by: Ben Wolsieffer <benwolsieffer@gmail.com>
In a system with multiple interfaces, the boot messages as well as the
status information provided by `systemctl` can be confusing without
an immediate way to differentiate between the different interfaces.
Fix this by adding the interface name to the unit description.
Signed-off-by: Gioele Barabucci <gioele@svario.it>
The received frame buffer was already verified to be long enough to
include the Advertisement Protocol element and that element was verified
to have a valid length value, but use of adv_proto[1] in another
function may have been too difficult to figure out for analyzers.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add support to specify a Link ID for set key operation for MLO
connection. This does not change the existing uses and only provides the
mechanism for extension in following commits.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Update the following MLO connection information to wpa_sm:
- AP MLD address and link ID of the (re)association link.
- Bitmap of requested links and accepted links
- Own link address for each requested link
- AP link address, RSNE and RSNXE for each requested link
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Currently, PMK parameters in the WPA state machine are set from
configuration only when the interface is initialized. If those
parameters are changed later via D-Bus, the new values don't have any
effect.
Call wpa_sm_set_param() when PMK-related D-Bus properties are changed
to immediately apply the new value; the control interface also does
something similar.
Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
Add the `sae_check_mfp` global option to limit SAE when PMF will
not be selected for the connection.
With this option SAE is avoided when the hardware is not capable
of PMF due to missing ciphers.
With this option SAE is avoided on capable hardware when the AP
does not enable PMF.
Allows falling back to PSK on drivers with the
WPA_DRIVER_FLAGS_SAE capability but do not support the BIP cipher
necessary for PMF. This enables configurations that can fall back
to WPA-PSK and avoid problems associating with APs configured
with `sae_require_mfp=1`.
Useful when `pmf=1` and `sae_check_mfp=1` are enabled and networks
are configured with ieee80211w=3 (default) and key_mgmt="WPA-PSK SAE".
In this configuration if the device is unable to use PMF due to
lacking BIP group ciphers it will avoid SAE and fallback to
WPA-PSK for that connection.
Signed-off-by: Jeffery Miller <jefferymiller@google.com>
Stop listen mode if there is not sufficient time remaining to complete
the Authentication exchange within the current remain-on-channel
operation. This speeds up the operation and avoids some timeouts that
could prevent the provisioning step from completing. This addresses an
issue that was found in the following test case sequence:
dpp_controller_relay_discover dpp_chirp_ap_5g
Similar mechanism was already used for Reconfig Announcement frames, so
reuse that for this case with Presence Announcement frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
When scanning for a new connection, we currently optimize by scanning
all frequencies only when our MCC capabilities will allow an additional
operating frequency, and scan only the existing operating frequencies
otherwise. This is problematic when there the current operating
frequency singularly accounts for one of the shared radio frequencies
because we should be able to switch operating frequencies without adding
to the channel count. Fix this.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
Connection attempt could have been intermittently drop when reconnecting
to the same ESS due the current BSS entry getting removed immediately
after the disconnection for the purpose of reconnecting to the same ESS.
Avoid this by not removing a BSS entry for the same ESS when in this
special state of trying to reconnect to the same ESS.
Signed-off-by : WooYong Kim <wykim@newratek.com>
Scans are allowed on the current interface for group formation only when
in the P2P_SEARCH, P2P_IDLE, or P2P_PROVISIONING state. But Extended
Listen timeout being enabled moves to the P2P_LISTEN_ONLY state. Due to
this P2P connection fails if the GO is not found with scans triggerred
before Extended Listen timeout. To avoid this skip Extended Listen
timeout to allow scans during group formation on the current interface.
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
Clone sae_pwe configuration value when creating a new P2P group
interface. This is needed to avoid P2P connection failure at the P2P
Client side due to SAE H2E being disabled in the 6 GHz band operation
when a new group interface is created for the connection.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
For the 6 GHz opclass 132, ch for loop only allows non-PSC channels { 1,
9, 17, 25, 33, 41, 49,... } to be used. This does not match the IEEE Std
802.11ax-2021 expectation of a 6 GHz-only AP "should set up the BSS with
a primary 20 MHz channel that coincides with a preferred scanning
channel".
Increase ch by 4 to allow PSC channel to be used for 6 GHz BW40.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
struct wpas_pasn is common to both initiator and responder, so rename it
to pasn_data to avoid the "wpas_" prefix that could be seen as a
reference to wpa_supplicant (PASN initiator).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The wpa_s and hapd context are isolated from the PASN initiator and
responder code and this functionality is now in the separate src/pasn
directory. Add option to build libpasn.so with this functionality. This
library can be used by a Wi-Fi Aware component to support NAN pairing
with other devices.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
PASN responder validates auth 1 frame and sends auth 2 frame to the
initiator. It analyses the auth 3 frame and verifies successful
authentication. Wi-Fi Aware modules can reuse this functionality through
a shared library libpasn.so generated from this code. Move the PASN
functionality that is now decoupled from the hapd context into a
separate file in a common directory to make it easier to build such a
library.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
PASN initiator functionality builds auth 1 and auth 3 frames, and
processes auth 2 frame received from the responder. Wi-Fi Aware modules
can reuse this functionality through a shared library libpasn.so
generated from this code. Move the PASN functionality that is now
decoupled from the wpa_s context into a separate file in a common
directory to make it easier to build such a library.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is helpful in being able to get the functionality needed for SAE
into a separate library (libpasn.so) without needing all of the
ieee802_11.c functionality.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Wi-Fi Aware R4 specification defines Beacon RSNE/RSNXE to be same as
RSNE/RSNXE present in Auth2 frame. So, MIC validation should be done
with the RSNE and RSNXE received in Auth2 frame.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Wi-Fi Aware R4 specification introduces a custom PMKID derived from
Nonce and TAG. This custom PMKID is included in PASN Authentication
frames during pairing verification. So, allow use of a custom PMKID in
PASN frames and validate it using a function handler. Wi-Fi Aware
component that uses libpasn.so should take care of validating the custom
PMKID.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
PTK is stored in the PTKSA cache following a successful PASN handshake,
however AKMP is removed upon a WPA PASN reset. The PASN handshake is
used in the Wi-Fi Aware R4 specification to define the pairing setup
process. KDK is used to generate a new set of keys, while AKMP is
required for key derivation for pairing. So, keep AKMP in the PTKSA
cache.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This makes hostapd use the struct defines from pasn_common.h so that the
same struct is shared with wpa_supplicant.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is a step towards decoupling the PASN initiator and responder
implemenentation is decoupled from the wpa_s and hapd contexts and
moving to a common folder for better abstraction. Move the struct
wpas_pasn definition to a common file for initiator and responder. The
idea is to provide a library libpasn.so from PASN common code. Include
C++ compatibilty wrapper to extend libpasn.so support for modules using
cpp code base.
This library can be used in applications implementing protocols based on
the PASN handshake.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Introduce a function handler to transmit PASN Authentication frames to
the driver. This removes the wpa_s dependency from PASN functionality
for sending the frames.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Get ssid and derive required information for SAE and FILS tunneled PASN
authentication to remove struct wpa_ssid dependency for PASN initiator.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Before invoking wpas_pasn_start(), derive KDK and secure LTF flags.
Instead of using network id for pasn_start(), use a pointer to the
struct wpa_ssid.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Obtain RSNXE capabilities from the driver flags as well and save them in
the wpas_pasn structure.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Remove wpa_s dependency for processing PASN M2 frame and preparing M3
frame. To hold the context of wpa_s when transmitting M3 frame, add cb
ctx.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is a step towards allowing the PASN implementation to be used
outside the context of wpa_supplicant.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Store PMKSA cache entry in wpas_pasn and remove wpa_sm dependency to add
an entry to PMKSA cache. This is a step towards allowing the PASN
implementation to be used outside the context of wpa_supplicant.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Use struct wpas_pasn (i.e., &wpa_s->pasn) as the function argument for
the SAE functionality that does not need the full struct wpa_supplicant
context. This is a step towards allowing PASN to be used outside the
context of wpa_supplicant.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Split wpas_pasn_reset() so that the main reset steps can be used without
an instance of struct wpa_supplicant. This is needed to allow PASN
implementation to be used for additional purposes outside the context of
wpa_supplicant.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
For wpa_supplicant_get_new_bss(), wpa_s->current_ssid can be NULL in
some cases. Add a NULL check before accessing it to avoid NULL pointer
dereference errors.
Fixes: 7784964cbe ("MLD STA: Fetch MLO connection info into core wpa_supplicant")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The initial wpa_drv_get_mlo_info() implementation cleared only the
valid_links information within struct driver_sta_mlo_info before trying
to fetch the information from the driver. While this is likely going to
work fine in practice, this can result in static analyzer warnings on
use of uninitialized memory (e.g., mlo.assoc_link_id could have been
read if wpa_s->valid_links was set to a nonzero value). In any case, it
is better to avoid such unnecessary warnings by clearing the full data
structure before using it.
Fixes: 7784964cbe ("MLD STA: Fetch MLO connection info into core wpa_supplicant")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The Linux kernel expects to use the AP MLD address as destination and
BSSID addresses for non-Public Action frames when the current
association is MLO capable. Use the MLD addresses to support this.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
EAPOL-Key msg 1/4 indication can be received before association
indication from the driver. For MLO connection, the source address check
of such frames should be against the AP MLD address instead of the
associated link BSSID.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Fetch the MLO association Link ID info from the driver to the
wpa_supplicant instance of the corresponding MLD STA interface. This
info is needed when setting the MLO connection info to wpa_sm.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Use a full list of AKM suite selectors that can use SAE authentication
when checking for authentication trigger from the driver.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This allows the P2P client to fast associate if the GO is already in the
scan cache without doing a full scan.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
AKM suite selector check was initially implemented with incorrect byte
swapping of the value from the driver (nl80211). Fix this and leave a
workaround option for any potentially deployed device where the driver
might be using the swapped byte order.
Fixes: 5ff39c1380 ("SAE: Support external authentication offload for driver-SME cases")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This can be helpful in trying to figure out unexpected behavior even
though we do not currently really do anything with the inner method
type.
Signed-off-by: Chaoli Zhou <quic_zchaoli@quicinc.com>
Move from this type of constructions:
switch (val) {
case 1:
something;
break;
}
default-action;
into following:
switch (val) {
case 1:
something;
break;
default:
default-action;
break
}
for cases where the switch statement is not expected to contain a full
set of enum values and as such, does not lose value from not having the
default target.
This makes the intent of default behavior clearer for static analyzers like
gcc with -Wswitch-default.
Signed-off-by: Chaoli Zhou <quic_zchaoli@quicinc.com>
Since NetworkManager doesn't support setting ieee80211w to
wpa_supplicant and only support pmf, so override ieee80211w from pmf for
AP mode if ieee80211w not configurated. Do not change behavior for the
P2P GO cases.
Signed-off-by: Chaoli Zhou <quic_zchaoli@quicinc.com>
While the IEEE 802.11 standard does not require MFPR=1, WPA3-Personal
requires PMF to be used with SAE. Use the stronger MFPR=1 configuration
for SAE-without-PSK case, i.e., interpret that as "WPA3-Personal only"
configuration.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Do not try to use variables that are not defined without
CONFIG_IEEE80211R=y and add the forgotten "inline" for the function
wrapper.
Fixes: 5c65ad6c0b ("PASN: Support PASN with FT key derivation")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Compiler throws a warning for using bitwise operation in
wpa_s_setup_sae_pt() function instead of logical AND operation on two
boolean values.
Fixes: e81ec0962d ("SAE: Use H2E unconditionally with the new AKM suites")
Signed-off-by: Sunil Ravi <sunilravi@google.com>
IEEE Std 802.11-2020, 11.8.8 (Selecting and advertising a new channel)
doesn't restrict switching to a channel which is not in the same band as
the current band. But at the same time, there are some issues in
switching between the 2.4/5 GHz bands and the 6 GHz band. So limit the
check to consider the critical use case of switching from a 5 GHz channel
to a 2.4 GHz channel.
Signed-off-by: Sunil Ravi <sunilravi@google.com>
While setting up the P2P GO interface, wpa_supplicant sets the operating
channel width to CHANWIDTH_USE_HT in cases where it fails to set 80 MHz
bandwidth. In the same flow, update the operating class, too, according
to the channel width. This is to avoid setting up the operational
channel width back to 80 MHz from hostapd interface setup.
Signed-off-by: Sunil <sunilravi@google.com>
wpas_p2p_optimize_listen_channel() checks for the state and current ssid
of the interface calling this function. This check prevents the function
from setting the optimized listen channel. Since the listen channel is
stored in global P2P configuration data, do not check the state and
current interface of the caller.
Signed-off-by: Sunil Ravi <sunilravi@google.com>
If wpa_supplicant was build without CONFIG_IEEE80211R, the
exposed key-management capabilities should not include one of the
FT protocols. If someone would use a FT protocol in such situation,
it would fail anyway.
Signed-off-by: Clemens Famulla-Conrad <cfamullaconrad@suse.de>
It is possible to specify -t or -K multiple times. With this the
value isn't boolean anymore and we hit a assert in libdbus
function `dbus_message_iter_append_basic()`, which expect 0 or 1
for DBUS_TYPE_BOOLEAN.
Signed-off-by: Clemens Famulla-Conrad <cfamullaconrad@suse.de>
Parse link id info from channel switch events and indicate the info to
control interface using new per link channel switch events. If channel
switch happens on the link which used during association both legacy
and new per-link channel switch events will be reported.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add support to fetch and indicate per-link MLO signal poll information
via a new control interface command MLO_SIGNAL_POLL.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Append the AP MLD address to CTRL-EVENT-CONNECTED when the current
connection uses MLO.
Signed-off-by: Aleti Nageshwar Reddy <quic_anageshw@quicinc.com>
Parse Multi-Link element received in scan result to get AP MLD address
and cache it in the wpa_bss structure.
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add a helper function to get Multi-Link element of a specified type from
scan result Probe Response frame or Beacon frame elements.
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
Add support to fetch MLO connection info from the driver to the
wpa_supplicant instance of corresponding MLD STA interface. In addition,
return true for BSSs associated with MLO links from wpa_bss_in_use() to
avoid getting them cleared from scan results.
Co-authored-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
P2P connections in the 6 GHz band should be limited to preferred
scanning channels since AP/GO discovery cannot depend on 2.4/5 GHz
discovery.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Previously, wpa_supplicant was using the current SSID for building the
SAE authentication commit frame for retries during external
authentication. But the external authentication SSID can be different
from the current SSID. Fix this by using the correct SSID profile.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
The driver's SME may choose a BSS of a different ESS (SSID) compared to
the current SSID and trigger external authentication. If the chosen SSID
is not associated/selected before by wpa_supplicant it won't have the
H2E PT derived. Make sure to derive PT for SSID indicated in the
external authentication request.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Commit e3bd6e9dc0 ("P2P: Use another interface operating channel as
listen channel") allows P2P listen channel to be selected based on
another interface operating channel if it is one of social channels
(i.e., 2.4 GHz 1, 6, 11).
This optimization is disabled by default due to the technical
specification expectations, but since this can be quite helpful for
optimized behavior, enable it by adding p2p_optimize_listen_chan=1 to
the default Android configuration template.
After the secure association and PTK derivation are completed, if the
device supports LTF keyseed, generate the LTF keyseed using KDK and set
the ranging context to the driver by using the command
QCA_NL80211_VENDOR_SUBCMD_SECURE_RANGING_CONTEXT.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Set secure ranging context to the driver for a valid PTKSA entry in the
PTKSA cache, if available. When the driver requests for PASN keys,
wpa_supplicant configures the keys from its cache if the keys for the
peer derived with the same own MAC address are available in the cache
instead of doing the full PASN handshake again.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add an option for an alternative processing of PTKSA life time expiry.
Register a callback in wpa_supplicant to handle the life time expiry of
the keys in PTKSA cache. Send PASN deauthentication when a PTKSA cache
entry expires.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This brings in the functionality to hold multiple peers and perform PASN
authentication with each peer at a time and send the PASN response to
the driver. PASN parameters such as AKMP and cipher suite are obtained
from the BSS information of the cached scan results. Also add
functionality to trigger deauthentication to the peer for which PASN
request with action PASN_ACTION_DELETE_SECURE_RANGING_CONTEXT is
received.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The driver requests PASN authentication for a peer with a specified
source (own) MAC address. Use the specified own MAC address for PASN
operations. This is needed to allow random MAC addresses to be used.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
On successful PASN handshake or 4-way handshake with a peer, PTK is
derived using the local and peer MAC addresses as input. Store the own
MAC address that is used for key derivation in PTKSA cache to maintain
that state over potential MAC addresses changes.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Use separate capabilities for AP and STA modes for P802.11az security
parameters secure LTF support, secure RTT measurement exchange support,
and protection of range negotiation and measurement management frames
support.
P802.11az security parameters are considered to be supported for both
station and AP modes if the driver sets NL80211_EXT_FEATURE_SECURE_LTF,
NL80211_EXT_FEATURE_SECURE_RTT, and
NL80211_EXT_FEATURE_PROT_RANGE_NEGO_AND_MEASURE flags. The driver can
advertize capabilities specific to each mode using
QCA_WLAN_VENDOR_FEATURE_SECURE_LTF*,
QCA_WLAN_VENDOR_FEATURE_SECURE_RTT*, and
QCA_WLAN_VENDOR_FEATURE_PROT_RANGE_NEGO_AND_MEASURE* flags.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
With introduction of newer AKMs, there is a need to update the PMK
length plumbed for the driver based 4-way handshake. To support this,
the current update the PMK length to 48, if the key management type uses
SHA-384. This is needed, e.g., for SUITE-B-192.
Signed-off-by: Vinayak Yadawad <vinayak.yadawad@broadcom.com>
If 6 GHz is supported by the device but 6 GHz P2P is disabled, P2P
invitation would fail if the GO select an operating channel which is not
the preferred channel. The root cause is that the 5 GHz and 6 GHz bands
are both HOSTAPD_MODE_IEEE80211A so the 5 GHz channels would be added
twice for the P2P Client's following scanning frequency list. This will
cause scanning to fail with -EINVAL. Fix this by adding the 5 GHz
channels only once.
Signed-off-by: Hector Jiang <jianghaitao@zeku.com>
According to the OCE specification, the STA shall select the AKM in
priority order from the list below.
1. FT Authentication over FILS (SHA-384) 00-0F-AC:17
2. FILS (SHA-384) 00-0F-AC:15
3. FT Authentication over FILS (SHA-256) 00-0F-AC:16
4. FILS (SHA-256) 00-0F-AC:14
5. FT Authentication using IEEE Std 802.1X (SHA-256) 00-0F-AC:3
6. Authentication using IEEE Std 802.1X (SHA-256) 00-0F-AC:5
7. Authentication using IEEE Std 802.1X 00-0F-AC:1
Move the FT-FILS-SHA256 check to be after the FILS-SHA384 one to match
this.
Signed-off-by: Seongsu Choi <seongsu.choi@samsung.com>
Add support to configure SAE, PSK, and PSK-SHA256 AKMs in connect
request when driver's SME in use. This is needed for implementing
WPA3-Personal transition mode correctly with any driver that handles
roaming internally.
Send additional AKMs configured in network block to driver based on
the maximum number of AKMs allowed by driver in connect request. Keep
first AKM in the list AKMs in the connect request as AKM selected by
wpa_supplicant to maintain backwards compatibility.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Use the recently added attribute to determine whether the kernel
supports a larger number of AKM suites in various commands.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
4-way handshake was failing after the driver roam from SAE to WPA-PSK
due to wpa_sm having an old PMK which was generated during previous SAE
connection.
To fix this update PSK to wpa_sm when AKM changes from SAE to WPA-PSK
for the target AP to have a correct PMK for 4-way handshake. Also,
update PSK to the driver when key management offload is enabled.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
This design was changed in the draft specification, so update
implementation to match the new design. Instead of including all
supported 2.4 and 5 GHz channels, generate the channel list using the
same mechanism that was already used for chirping.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This procedure will be used for PB discovery as well, so move the
frequency array generation into a helper function.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
dpp_discard_public_action=1 was not supposed to prevent network
introduction, i.e., it was only for frames that could go through the
DPP-over-TCP path. Fix this not to prevent network introduction when
using DPP-over-TCP to configure a DPP AKM profile.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
For now, do not include 6 GHz channels since finding a Configurator from
a large number of channels would take excessive amount of time.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This can be helpful for upper layers to be able to determine whether the
configuration was rejected.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
ipv4_params/ip6_params in type4_params maintains separate classifier
mask while type4_params already has a common classifier_mask. Lets
use the common classifier mask for both ipv4/ipv6 params and remove
the redundant params_mask in ipv4_params/ip6_params.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
The DPP_CONTROLLER_START control interface command can be used without
any arguments, so do not force at least a single argument to be included
in wpa_cli and hostapd_cli.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
CRYPTO_RSA_OAEP_SHA256 is not sufficient here since ssid->eap does not
exist without IEEE8021X_EAPOL.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The new SAE AKM suites are defined to use H2E, so ignore the sae_pwe
value when these AKM suites are used similarly to the way H2E gets
enabled when SAE Password Identifiers are used.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Define new WPA_KEY_MGMT_* values for the new SAE AKM suite selectors
with variable length keys. This includes updates to various mapping and
checking of the SAE key_mgmt values.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Use the existing helper function instead of maintaining multiple copies
of lists of SAE key management suites.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This was already done in hostapd and same is needed for wpa_supplicant
to avoid testing issues due to session overlap detection from previous
test cases.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Verify that the peer does not change its bootstrapping key between the
PKEX exchange and the authentication exchange.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
When PKEX was started through the push button mechanism, the own
bootstrapping key was not bound correctly to the Authentication phase
information and that ended up in incorrectly generating a new
bootstrapping key for the Authentication exchange. Fix this by added the
needed own=<id> parameter into the cached parameters when using push
button.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The peer=<id> information about the specific boostrapping key provided
through PKEX was added for Public Action frame cases, but the TCP
variant did not do same. Add the same information there to maintain
knowledge of the specific peer bootstrapping key from PKEX to
Authentication exchange.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Extend DPP push button support in wpa_supplicant to allow the role of
the Configurator to be used. This provides similar functionality to the
way the DPP_PUSH_BUTTON command in hostapd worked when providing the
configuration parameters with that command (instead of building the
config object based on current AP configuration).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
It is possible for a Controller to receive a copy of its own PKEX
Exchange Request in the case where the Controller is initiating a PKEX
exchange through a Relay. The Configurator role in the device would have
a matching PKEX code in that case and the device might reply as a PKEX
responder which would result in going through the exchange with the
Controller device itself. That is clearly not desired, so recognize this
special case by checking whether the Encrypted Key attribute value
matches a pending locally generated one when processing a received PKEX
Exchange Request.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
We are not supposed to reuse these without being explicitly requested to
perform PKEX again. There is not a strong use case for being able to
provision an Enrollee multiple times with PKEX, so this should have no
issues on the Enrollee. For a Configurator, there might be some use
cases that would benefit from being able to use the same code with
multiple Enrollee devices, e.g., for guess access with a laptop and a
smart phone. That case will now require a new DPP_PKEX_ADD command on
the Configurator after each completion of the provisioning exchange.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The new global configuration parameter
dpp_connector_privacy_default=<0/1> can now be used to set the default
value for the dpp_connector_privacy parameter for all new networks
provisioned using DPP.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a privacy protecting variant of the peer introduction protocol to
allow the station device to hide its Connector from 3rd parties. The new
wpa_supplicant network profile parameter dpp_connector_privacy=1 can be
used to select this alternative mechanism to the peer introduction
protocol added in the initial release of DPP.
It should be noted that the new variant does not work with older DPP APs
(i.e., requires support for release 3). As such, this new variant is
disabled by default.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This allows the DPP Configuration Request Object from an Enrollee to be
extended with 3rd party information. The new dpp_extra_conf_req_name and
dpp_extra_conf_req_value configuration parameters specify the name of
the added JSON node and its contents. For example:
dpp_extra_conf_req_name=org.example
dpp_extra_conf_req_value={"a":1,"b":"test"}
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Allow the Responder/Initiator hash values to be corrupted in Push Button
Presence Announcement messages for testing purposes.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add support to use a push button -based bootstrap mechanism with DPP.
The new DPP_PUSH_BUTTON control interface command enables this mode on
the AP/hostapd and station/wpa_supplicant. This goes through the
following sequence of events: a suitable peer in active push button mode
is discovered with session overlap detection, PKEX is executed with
bootstrap key hash validation, DPP authentication and configuration
exchanges are performed.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Move most of CHANWIDTH_* definitions from ieee80211_defs.h to defs.h as
the definitions are getting used mostly for internal purpose only. Also
change prefix of the definitions to CONF_OPER_CHWIDTH_* and update in
all the files accordingly.
Leave the couple of VHT-specific exceptions to use the old defines (the
reason why they were originally added as VHT values), to avoid use of
clearly marked configuration values in information elements. In
addition, use the defines instead of magic values where appropriate.
Signed-off-by: Aleti Nageshwar Reddy <quic_anageshw@quicinc.com>
For hidden GBK encoding of a Chinese SSID, both the UTF-8 and GBK
encoding profiles are added into wpa_supplicant to make sure the
connection succeeds. In this situation, wpa_supplicant_select_network()
will not be called so current_ssid is NULL when association begins.
Android monitors the WPA_EVENT_STATE_CHANGE event to get the SSID and
BSSID. When connecting to a Chinese SSID, in case of association
rejection happens, Android will report null SSID to OEM APP because
current_ssid is updated after wpa_supplicant_set_state(wpa_s,
WPA_ASSOCIATING), which may cause confusion.
Fix this by setting the current_ssid before changing state to
ASSOCIATING.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Previously, the driver could optionally (using QCA vendor command)
provide a preferred channel list to wpa_supplicant for channel selection
during the GO negotiation. Channel selection process can be more
efficient with the information of weights and flags of the preferred
channel list that can be provided by the driver. Use a weighted
preferred channel list provided by the driver for channel selection
during GO negotiation if such a list is available.
Signed-off-by: Sreeramya Soratkal <quic_ssramya@quicinc.com>
Extend IMSI privacy functionality to allow an attribute (in name=value
format) to be added using the new imsi_privacy_attr parameter.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This can be used to make sure wpa_supplicant does not process DPP
messages sent in Public Action frames when a test setup is targeting
DPP-over-TCP.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Use imsi_privacy_cert as the name of the configuration parameter for the
X.509v3 certificate that contains the RSA public key needed for IMSI
privacy. The only allowed format for this information is a PEM-encoded
X.509 certificate, so the previous name was somewhat confusing.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Disable a network profile that has set the imsi_privacy_key if a valid
key cannot be read from the specified file. Previously, this check was
done only after having associated, but there is no point in associating
just to see EAP authentication fail in such a case. This is needed for
avoiding connection attempts if the X.509 certificate for IMSI privacy
has expired.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
tcp_addr=from-uri can now be used as a special case for initiating
DPP-over-TCP to the destination indicated in the peer bootstrapping URI.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Limit the GAS comeback delay to 60000 TUs, i.e., about 60 seconds. This
is mostly to silence static analyzers that complain about unbounded
value from external sources even though this is clearly bounded by being
a 16-bit value.
Signed-off-by: Jouni Malinen <j@w1.fi>
The length of the URL, i.e., pos[0], is verified here to be within the
bounds of the recieved message, but that seemed to be done in a manner
that might bee too complex for static analyzers to understand.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like fst_wpa_obj::get_hw_modes would have been left
uninitialized in hostapd. It is not obviously clear why this would not
have caused issues earlier, but in any case, better make this set
properly to allow unexpected behavior should that function pointer ever
be used.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a parameter (non_coloc_6ghz=1) to the manual scan command to disable
6 GHz collocated scanning.
This option can be used to disable 6 GHz collocated scan logic. Note
that due to limitations on Probe Request frame transmissions on the 6
GHz band mandated in IEEE Std 802.11ax-2021 it is very likely that
non-PSC channels would be scanned passively and this can take a
significant amount of time.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Set NL80211_SCAN_FLAG_COLOCATED_6GHZ in the scan parameters to enable
scanning for co-located APs discovered based on neighbor reports from
the 2.4/5 GHz bands when not scanning passively. Do so only when
collocated scanning is not disabled by higher layer logic.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
RSN design is supposed to encrypt all Data frames, including EAPOL
frames, once the TK has been configured. However, there are deployed
implementations that do not really follow this design and there are
various examples from the older uses of EAPOL frame where those frames
were not encrypted. As such, strict filtering of unencrypted EAPOL
frames might results in undesired interoperation issues.
However, some of the most important cases of missing EAPOL frame
encryption should be possible to handle without causing too significant
issues. These are for cases where an attacker could potentially cause an
existing association to be dropped when PMF is used. EAP-Request is one
potential candidate for such attacks since that frame could be used to
initiate a new EAP authentication and the AP/Authenticator might not
allow that to complete or a large number of EAP-Request frames could be
injected to exceed the maximum number of EAP frames. Such an attack
could result in the station ending up disconnecting or at minimum,
getting into somewhat mismatching state with the AP.
Drop EAPOL-EAP frames when it is known that it was not encrypted but
should have been and when PMF is enabled. While it would be correct to
drop this even without PMF, that does not provide any significant
benefit since it is trivial to force disconnection in no-PMF cases. It
should also be noted that not all drivers provide information about the
encryption status of the EAPOL frames and this change has no impact with
drivers that do not indicate whether the frame was encrypted.
Signed-off-by: Jouni Malinen <j@w1.fi>
This information was already available from the nl80211 control port RX
path, but it was not provided to upper layers within wpa_supplicant and
hostapd. It can be helpful, so parse the information from the driver
event.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds wifi_generation=7 line to the STATUS output if the driver
reports (Re)Association Request frame and (Re)Association Response frame
information elements in the association or connection event with EHT
capability IEs.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Send the status code from the AP authentication response instead of
sending the hardcoded WLAN_STATUS_UNSPECIFIED_FAILURE when the external
SAE authentication failure is due to an explicit rejection by the AP.
This will allow the driver to indicate the correct status in connect
response.
For example, an AP can send WLAN_STATUS_AP_UNABLE_TO_HANDLE_NEW_STA in
SAE authentication response. With this change the driver gets the real
status for the SAE authentication failure and it can fill the correct
status in the connect response event.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
The TLS protocol design for renegotiation was identified to have a
significant security flaw in 2009 and an extension to secure this design
was published in 2010 (RFC 5746). However, some old RADIUS
authentication servers without support for this are still used commonly.
This is obviously not good from the security view point, but since there
are cases where the user of a network service has no realistic means for
getting the authentication server upgraded, TLS handshake may still need
to be allowed to be able to use the network.
OpenSSL 3.0 disabled the client side workaround by default and this
resulted in issues connection to some networks with insecure
authentication servers. With OpenSSL 3.0, the client is now enforcing
security by refusing to authenticate with such servers. The pre-3.0
behavior of ignoring this issue and leaving security to the server can
now be enabled with a new phase1 parameter allow_unsafe_renegotiation=1.
This should be used only when having to connect to a network that has an
insecure authentication server that cannot be upgraded.
The old (pre-2010) TLS renegotiation mechanism might open security
vulnerabilities if the authentication server were to allow TLS
renegotiation to be initiated. While this is unlikely to cause real
issues with EAP-TLS, there might be cases where use of PEAP or TTLS with
an authentication server that does not support RFC 5746 might result in
a security vulnerability.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
pbkdf2_sha1() may return errors and this should be checked in calls.
This is especially an issue with FIPS builds because the FIPS
requirement is that the password must be at least 14 characters.
Signed-off-by: Juliusz Sosinowicz <juliusz@wolfssl.com>
Add support for IMSI privacy in the EAP-SIM/AKA peer implementation. If
the new wpa_supplicant network configuration parameter imsi_privacy_key
is used to specify an RSA public key in a form of a PEM encoded X.509v3
certificate, that key will be used to encrypt the permanent identity
(IMSI) in the transmitted EAP messages.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add new crypto wrappers for performing RSA-OAEP-SHA-256 encryption and
decryption. These are needed for IMSI privacy.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Modify hostapd_set_freq_params() to include EHT parameters and update
the calling functions to match.
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Add compilation support for IEEE 802.11be along with options to enable
EHT support per radio and disable per interface.
Enabling HE is mandatory to enable EHT mode.
Tested-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
The comment about the IEEE 802.11ax functionality being experimental and
based on a not yet finalized standard is not accurate anymore since IEEE
Std 802.11ax-2021 has already been published. Remove that comment and
add the entry for wpa_supplicant as well.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
When a station receives either a Beacon frame or a Probe Response frame
from an AP that contains an MBO element with the Association Disallowed
attribute, the station should prevent association to that AP. When using
passive scanning, it is possible for the scan results to contain the
latest information in the Beacon frame elements instead of the Probe
Response frame elements. That could result in using old information and
not noticing the AP having changed its state to disallowing new
associations.
Make it more likely to follow the AP's change to disallow associations
by checking the Beacon frame elements instead of Probe Response frame
elements if the scan results are known to contain newer information for
the Beacon frame.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
It can be helpful to know whether the information elements from the
Beacon frame or the Probe Response frame are newer when using BSS table
entries, so make this information known, if available. This allows the
Beacon frame elements to be preferred over the Probe Response frame
elements when desired.
Signed-off-by: Jouni Malinen <j@w1.fi>
As part of fixing CONFIG_NO_WPA_PASSPHRASE, whilst wpa_passphrase gets
built, its not installed during `make install`.
Fixes: cb41c214b7 ("build: Re-enable options for libwpa_client.so and wpa_passphrase")
Signed-off-by: Alex Kiernan <alexk@zuma.ai>
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Sometimes there is a program error to send a large number of commands to
wpa_supplicant, and the source address can help quickly find the program
that sends commands.
Signed-off-by: xinpeng wang <wangxinpeng@uniontech.com>
eapol_test.c contains variants of couple of functions from the hostapd
implementation. Those had not been updated for a while and this commit
brings in the main changes to keep the implementations closer to
each other.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is needed to allow wpa_supplicant to be built with EAP-pwd, but
without any other EAP method that pulled in MS_FUNCS.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible to miss the HMAC functions if some other build
configuration parameters ended up setting NEED_SHA384/512=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous mechanism of unloaded the providers from tls_deinit() did
not work correctly for some cases. In particular, it was possible for
hostapd to end up unloading both providers and not being able to recover
from this if TLS server was not enabled.
Address this more cleanly by introducing a new crypto_unload() function
that will be called when the process is exiting.
Fixes: 097ca6bf0b ("OpenSSL: Unload providers on deinit")
Signed-off-by: Jouni Malinen <j@w1.fi>
The DH file parameters are applicable only for the TLS server, so this
parameter did not really have any impact to functionality. Remove it to
get rid of useless code and confusing documentation for the network
block configuration.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 0b5e98557e ("FIPS: Use OpenSSL CMAC implementation instead of
aes-omac1.c") added this implementation initially only for the FIPS
builds. However, there does not seem to be any remaining need to avoid
depending on the OpenSSL library implementation for builds, so move to
that implementation unconditionally to reduce the binary size a bit.
Signed-off-by: Jouni Malinen <j@w1.fi>
When receiving a beacon report request with the mode set to active,
channels that are marked as NO_IR were not added to the scan request.
However, active mode just mean that active scan is allowed, but not
that it is a must, so these channels should not be omitted.
Include channels that are marked as NO_IR in the scan request even
if the mode is set to active.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
The id and cred_id variables are reset to 0 every time the
wpa_config_read() function is called, which is fine as long as it is
only called once. However, this is not the case when using both the -c
and -I options to specify two config files.
This is a problem because the GUI, since commit eadfeb0e93 ("wpa_gui:
Show entire list of networks"), relies on the network IDs being unique
(and increasing), and might get into an infinite loop otherwise.
This is solved by simply making the variables static.
Signed-off-by: Naïm Favier <n@monade.li>
force_kdk_derivation is defined within CONFIG_TESTING_OPTIONS, so need
to use matching condition when accessing it.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
On the 6 GHz band the following is not allowed (see IEEE Std
802.11ax-2021, 12.12.2), so do not allow association with an AP using
these configurations:
- WEP/TKIP pairwise or group ciphers
- WPA PSK AKMs
- SAE AKM without H2E
In addition, do not allow association if the AP does not advertise a
matching RSNE or does not declare that it is MFP capable.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
So far, this option was only present in the Makefiles. Document it as
being available for configuration since the WFA program has already been
launched.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
The default behavior in wpa_supplicant is to disable use of TLSv1.3 in
EAP-TLS unless explicitly enabled in network configuration. The new
CONFIG_EAP_TLSV1_3=y build parameter can be used to change this to
enable TLSv1.3 by default (if supported by the TLS library).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
It would have been possible for the authentication attemps to go into a
loop if the AP/Authenticator/authentication server were to believe EAP
authentication succeeded when the local conclusion in Supplicant was
failure. Avoid this by timing out authentication immediately on the
second consecutive EAP authentication failure.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
To support the STA testbed role, the STA has to disable transmitting
EAPOL-Key group msg 2/2 of Group Key Handshake. Add test parameter to
disable sending EAPOL-Key group msg 2/2 of Group Key Handshake.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
STA needs to check AP's information after receive reassociation
response. STA uses connected AP's Beacon/Probe Response frame to compare
with Reassociation Response frame of the target AP currently. However,
if one AP supports OCV and the other AP doesn't support OCV, STA will
fail to verify RSN capability, then disconnect. Update current_bss to
the target AP before check, so that STA can compare correct AP's RSN
information in Reassociation Response frame.
Signed-off-by: Xin Deng <quic_deng@quicinc.com>
Add AP mode commands for ACL and BTM into wpa_cli similarly to the way
these were already available in hostapd_cli.
Signed-off-by: Chaoli Zhou <quic_zchaoli@quicinc.com>
Support installing the updated allow/deny list to the driver if it
supports ACL offload. Previously, only the not-offloaded cases were
updated dynamically.
Signed-off-by: Chaoli Zhou <quic_zchaoli@quicinc.com>
Extend AP mode ACL control interface commands to work from
wpa_supplicant in addition to the previously supported hostapd case.
Signed-off-by: Chaoli Zhou <quic_zchaoli@quicinc.com>
Extend AP mode BTM control interface commands to work from
wpa_supplicant in additiona to the previously support hostapd case.
Signed-off-by: Chaoli Zhou <quic_zchaoli@quicinc.com>
Enable BTM capability for AP mode only and do not affect P2P GO mode.
This can be used for AP band steering when using wpa_supplicant to
control AP mode operations.
Signed-off-by: Chaoli Zhou <quic_zchaoli@quicinc.com>
dpp_configurator_params changes were taken into use in the
non-TCP/Controller case immediately on change, but that was not the case
for the Controller where this was updated only when explicitly starting
it. Change this to update dpp_configurator_params for the Controller as
well even if it is already running.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Since commit 200c7693c9 ('Make WEP functionality an optional build
parameter'), WEP support is optional and, indeed, off by default.
The distributions are now catching up and disabling WEP in their builds.
Unfortunately, there's no indication prior to an attempt to connect to a
WEP network that it's not going to work. Add a capability to communicate
that.
Unlike other capabilities, this one is negative. That is, it indicates
lack of a WEP support as opposed to its presence. This is necessary
because historically there has been no capability to indicate presence
of WEP support and therefore NetworkManager (and probably others) just
assumes it's there.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Davide Caratti <davide.caratti@gmail.com>
CurrentAuthMode should be set as a real auth type when authentication is
in progress. wpa_supplicant has a property "State" which indicates the
authentication stage already. I think setting auth mode as "INACTIVE" in
all auth progress stages is not a good idea, because sometimes we need
to handle this connection according to the auth type even when
authentication is not complete. For example, NetworkManager may recall
ask-password-dialog when auth mode is "wpa-psk" and "sae", try next
access point when auth mode is "EAP-xx" when password is incorrect.
Since "CurrentAuthMode" is set as "INACTIVE" in all not fully completed
situations, we do not know how to handle it.
Signed-off-by: Aris Aachen <chenyunxiong@unionitech.com>
Signed-off-by: ArisAachen <chenyunxiong@uniontech.com>
This is mainly for testing purposes to allow a Configurator to the curve
between provisioning cases. This would not work for real deployement
cases unless every Enrollee were reconfigured.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Allow the Configurator to be configured to use a specific curve for the
netAccessKey so that it can request the Enrollee to generate a new key
during the configuration exchange to allow a compatible Connector to be
generated when the network uses a different curve than the protocol keys
used during the authentication exchange.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Allow PKEX v1-only or v2-only behavior to be specific for the Responder
role. This is mainly for testing purposes.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Commit a41a29192e ("build: Pull common fragments into a build.rules
file") introduced a regression into wpa_supplicant build process. The
build target libwpa_client.so is not built regardless of whether the
option CONFIG_BUILD_WPA_CLIENT_SO is set or not. This happens because
this config option is used before it is imported from the configuration
file. Moving its use after including build.rules does not help: the
variable ALL is processed by build.rules and further changes are not
applied. Similarly, option CONFIG_NO_WPA_PASSPHRASE also does not work
as expected: wpa_passphrase is always built regardless of whether the
option is set or not.
Re-enable these options by adding both build targets to _all
dependencies.
Fixes: a41a29192e ("build: Pull common fragments into a build.rules file")
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Couple of the WPS/P2P/RADIUS-PSK cases were freeing heap memory
allocations without explicitly clearing the PSK value. Add such clearing
for these to avoid leaving the PSK in memory after it is not needed
anymore.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is needed to avoid leaving wpa_state to SCANNING if network
introduction fails and a new association is not started.
This was found with the following test case sequence:
dpp_conn_status_connector_mismatch scan_trigger_failure
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
A previously set netrole (e.g., from DPP_LISTEN or DPP_AUTH_INIT) could
have been used in a following DPP_CHIRP or DPP_RECONFIG operation. This
could result in trying to request incorrect configuration and likely
rejection from the Configurator. Fix this by clearing the netrole when
starting these operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for at least the wpa_s->last_ssid to be left pointing to
a removed network which could result in processing the following
association as a reassociation-within-an-ESS even when it was moving to
a different ESS. This could result in unexpected behavior. This was
found with the following test case sequence:
sigma_dut_ap_psk_sae_ft sae_h2e_password_id ap_wps_pk_oom sigma_dut_client_privacy
Move clearing of wpa_s->last_ssid and wpa_s->current_ssid into
wpas_notify_network_removed() to catch all cases similarily to the way
wpa_s->next_ssid was already cleared.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The offchannel frame TX wait was stopped whenever processing
DPP_STOP_LISTEN in most cases. However, there was a corner case on the
Responder side where this operation was skipped after PKEX was completed
successful and the Authentication Request frame had not yet been
received from the Initiator.
While this does not normally cause any significant issue, this could
result in unexpected behavior especially in test cases that run multiple
DPP PKEX operations in a row since the start of a new TX operation might
get delayed while waiting for the previous TX-wait to complete.
This was found with the following test case sequence:
dpp_reconfig_retries dpp_pkex_alloc_fail
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Allow macsec_csindex to be configured and select the cipher suite when
the participant acts as a key server.
Signed-off-by: leiwei <quic_leiwei@quicinc.com>
There is no need to maintain the DPP authentication state if config
request processing fails, so clear state also in the GAS server request
handler similarly to the other failure cases.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The hwsim test cases are trying to clear this parameter between test
cases, but that was not really done correctly for many of the sigma_dut
test cases. Instead of fixing the text scripts to do this more
carefully, it seems to be simpler to just force the FLUSH command to
clear this.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is needed since the gas_query_req() operation could remain waiting
indefinitely for the response if the Configurator keeps sending out
comeback responses with additional delay. The DPP technical
specification expects the Enrollee to continue sending out new Config
Requests for 60 seconds, so this gives an extra 60 second time after the
last expected new Config Request for the Configurator to determine what
kind of configuration to provide.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Instead of depending on the TX-wait-response-time to be sufficient to
cover the full GAS exchange, start an ongoing listen operation on the
negotiation channel (if no such listen operation is already in place) to
allow the configuration exchange to take longer amount of time. This is
needed for cases where the conf=query is used to request Configurator
parameters from upper layers and that upper layer processing (e.g., user
interaction) takes significant amount of time.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Once the GO/AP interface initialization is completed, check if the
operating frequency set in the wpa_supplicant group interface structure
is different than the one set in the hostapd interface structure
associated with the group interface. If yes, update the frequency in the
wpa_supplicant group interface and network configuration to the
frequency set in the hostapd interface structure.
The frequency set in the hostapd interface is the correct/final
frequency wpa_supplicant configured in the kernel/driver. This is done
because wpa_supplicant may switch the initially requested primary and
secondary frequencies to get a secondary frequency with no beacons (to
avoid interference or 20/40 MHz coex logic). And the updated frequency
is informed by the driver only after the interface setup is completed
through the channel switch event - EVENT_CH_SWITCH. But wpa_supplicant
updates the frequency to applications through the P2P_GROUP_STARTED
event which is triggered before the EVENT_CH_SWITCH event. To send the
correct frequency to applications the frequency must be updated before
sending the P2P_GROUP_STARTED event.
Bug: 191272346
Test: Manual - Verified that GO frequency is updated and reported
correctly to Nearby application.
Signed-off-by: Sunil Ravi <sunilravi@google.com>
This provides an alternative mechanism for upper layer components to
control configuration parameters to be used by the local Configurator.
Instead of the previously used design where the Configurator parameters
had to be provided before initiating the DPP Authentication exchange,
the new alternative approach allows the DPP Authentication exchange to
be started before any Configurator parameters have been determined and
wpa_supplicant will then request the parameters once the DPP
Configuration Request has been received from the Enrollee. This allows
the Config Request information to be used at upper layers to determine
how the Enrollee should be configured.
For example for an Initiator:
CTRL: DPP_QR_CODE <URI from Responder/Enrollee>
CTRL: DPP_AUTH_INIT peer=1 conf=query
<3>DPP-CONF-NEEDED peer=1 src=02:00:00:00:00:00 net_role=sta name="Test" opclass=81,82,83,84,115,116,117,118,119,120,121,122,123,124,125,126,127,128,129,130 mud_url=N/A
(upper layer processing; potentially including user interaction)
CTRL: DPP_CONF_SET peer=1 conf=sta-sae ssid=736165 pass=70617373776f7264
<3>DPP-CONF-SENT
For example for a Responder:
CTRL: SET dpp_configurator_params conf=query
CTRL: DPP_LISTEN 2412 role=configurator
<3>DPP-CONF-NEEDED peer=2 src=02:00:00:00:01:00 net_role=sta name="Test" opclass=81,82,83,84,115,116,117,118,119,120,121,122,123,124,125,126,127,128,129,130 mud_url=N/A
(upper layer processing; potentially including user interaction)
CTRL: DPP_CONF_SET peer=2 conf=sta-sae ssid=736165 pass=70617373776f7264
<3>DPP-CONF-SENT
For example for an Initiator that can act both as a Configurator and an
Enrollee in a case where the Initiator becomes the Enrollee:
CTRL: DPP_AUTH_INIT peer=1 role=either conf=query
<3>DPP-CONF-RECEIVED
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Extend the GAS server functionality to allow a request handler to return
the initial comeback delay with a later callback instead of having to
indicate the comeback delay when returning from the handler function.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The TCP code path did not handle the postponed connection attempt on TX
status and the following result message from the Enrollee to the
Configurator. Fix this by adding TCP-versions of these operations to
match the way wpa_supplicant implemented this for the Public Action
frames.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This extends dpp_test functionality to allow DPP Network Introduction
exchanges to use an incorrect value in the Protocol Version attribute.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Use a separate ver=<1|2> parameter to DPP_PKEX_ADD instead of
overloading init=1 with version indication. This allows additional
options for forcing v1-only and v2-only in addition to automatic mode
(start with v2 and fall back to v1, if needed).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Use automatic PKEX version negotiation as the initiator by starting with
PKEXv2 and if no response is received, trying again with PKEXv1. For
now, this is enabled only in wpa_supplicant CONFIG_DPP3=y builds.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The rx_freq of Public Action frame was not maintained by the GO and the
GO always sent the response on the operating channel. This causes
provision discovery failure when a P2P Device is sending a PD Request on
a 2.4 GHz social channel and the GO is responding on a 5 GHz operating
channel.
Save the rx_freq and use it for GO to sent the response. This extends
commit c5cc7a59ac ("Report offchannel RX frame frequency to hostapd")
to cover additional frame types.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Update the version number for the build and also add the ChangeLog
entries for both hostapd and wpa_supplicant to describe main changes
between v2.9 and v2.10.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like the recently added roam_in_progress and
bss_trans_mgmt_in_progress flags could end up getting set, but not
cleared, in some cases. Make sure these get cleared on explicit
disconnection request and also in case the SME-in-driver path is used
(while that path does not really use these flags yet, it is better to
not allow them to be forgotten to be set should it be extended to cover
similar functionality).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
After receiving a BSS Transition Management request,
wpa_supplicant_connect() will abort ongoing scans, which will cause scan
results to be reported. Since the reassociate bit is set, this will
trigger a connection attempt based on the aborted scan's scan results
and cancel the initial connection request. This often causes
wpa_supplicant to reassociate to the same AP it is currently associated
to instead of the AP it was asked to transition to.
Add a bss_trans_mgmt_in_progress flag to indicate that we're currently
transitioning to a different AP so that we don't initiate another
connection attempt based on the possibly received scan results from a
scan that was in progress at the time the BSS Transition Management
request was received.
This is the equivalent of commit 5ac977758d ("Reject authentication
start during explicit roam requests") for the roaming scenario.
Signed-off-by: Nicolas Norvez <norvez@chromium.org>
Make wpas_dbus_handler_interworking_select() conditional on
CONFIG_INTERWORKING to avoid compilation issues.
Fixes: c8e4283f90 ("D-Bus: Interworking network selection")
Signed-off-by: Alex Kiernan <alexk@zuma.ai>
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
The radio work starting may be delayed. If the DPP listen operation is
stopped before the radio work starts, the pending dpp-listen radio work
won't get cleaned up, which might lead to failing to start the next DPP
listen operation.
Issue scenario: DPP start -> dpp-listen radio work added but not started
-> DPP stop, pending radio work not cleaned up -> radio work start ->
trying to start DPP but failing because a dpp-listen work already
exists.
This commit removes the potential pending dpp-listen radio
work when DPP stops.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
wpa_supplicant may use wrong SAE authentication method if it doesn't
have the scan result for the target BSS since RSNXE information is not
available.
For example, STA might use the hunting-and-pecking loop method for SAE
authentication even though AP supports SAE H2E and STA is configured
with sae_pwe=2.
This is possible in cases like EXTERNAL_AUTH triggered by the driver
during roaming. To avoid this update scan results to fetch the target
BSS scan result from the driver.
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
Allow mesh_fwding (dot11MeshForwarding) to be specified in a mesh BSS
config, pass that to the driver (only nl80211 implemented for now) and
announce forwarding capability accordingly.
Signed-off-by: José Pekkarinen <jose.pekkarinen@unikie.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add the "InterworkingSelect" method to the DBus API to trigger an
Interworking scan with ANQP fetches. When a BSS that matches a
configured credential is found, the result is emitted using the signal
"InterworkingAPAdded". Completion of the full InterworkingSelect
operation is indicated with the "InterworkingSelectDone" signal.
Signed-off-by: Damien Dejean <damiendejean@chromium.org>
Add "AddCred", "RemoveCred", and "RemoveAllCreds" methods to the D-Bus
API of the network interface to allow the caller to manipulate a set of
Interworking credentials similarly to the way this was enabled through
the control interface.
Signed-off-by: Damien Dejean <damiendejean@chromium.org>
This allows the same functions to be used for both the control interface
and the D-Bus interface.
Signed-off-by: Damien Dejean <damiendejean@chromium.org>
Add the support of engine, engine_id, ca_cert_id, cert_id, and key_id
parameters to credential blocks for Hotspot 2.0.
Signed-off-by: Damien Dejean <damiendejean@chromium.org>
The P2P DBus interface was using the wrong interface name when calling
wpas_p2p_invite_group(). Capture the group interface name before calling
the method to fix this.
Signed-off-by: Hicham Hassoubi <Hicham_hassoubi@bose.com>
This reverts commit 3204795d7a.
The commit adds an additional check that checks for overlapping BSSs in
addition to the existing 40 MHz intolerance subfield checks. The commit
cites IEEE Std 802.11-2016, 11.16.12, which defines the proper behavior
for a 20/40 MHz HT STA and AP, but the standard actually doesn't say
anything about overlapping BSSs. Specifically, the standard states that
the only BSSs that belong in the Intolerant channel report are those
that satisfy trigger event A, defined as channels with BSSs that don't
contain the HT capabilities element (which wpa_supplicant already did
before). Note that we also include channels with BSSs that have the 40
MHz intolerance bit set in the Intolerant channel report.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
Add support for PKEXv2 core protocol. This defines a new PKEX Exchange
Request message type with protocol negotiation and different rules for
key derivation with PKEXv2 or newer is used.
This does not change existing behavior for PKEX, i.e., the PKEXv1
variant will still be used by default.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Allow the dpp_test parameter to be used to request the Protocol Version
attributed to be omitted from the Peer Discovery Request/Response
message.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Verify that the Protocol Version attribute is used appropriate in Peer
Discovery Request/Response messages in cases where the signed Connector
includes the version information.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Generate Peer Discovery Request/Response messages using the protected
version from the Connector, if present, instead of the currently
supported protocol version which might be higher than the one that got
included into the signed Connector during provisioning earlier.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
CONFIG_DPP3=y can now be used to configure hostapd and wpa_supplicant
builds to include DPP version 3 functionality. This functionality is
still under design and the implementation is experimental and not
suitable to be enabled in production uses before the specification has
been finalized.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Align the process logic for ap_vendor_elements and ap_assocresp_elements
parsing by using the wpabuf_parse_bin() helper function in both.
Signed-off-by: Chaoli Zhou <zchaoli@codeaurora.org>
wpa_add_scan_freqs_list() was updated to use bool for the is_6ghz
argument, but these callers were missed when updating the values from
0/1 to false/true.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The channels included for the scan to connect to a P2P GO are optimized
such that the P2P GO preferred channel and the common channels are
included for the first few scans followed by a full scan in which all
the channels supported by the local device are included. This results in
P2P client including the 6 GHz channels for the full scan after GO
Negotiation even when 6 GHz channels are not used for the P2P
connection.
Exclude the 6 GHz channels from the full scan if 6 GHz channels are
supported but are not used for P2P connection.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
After roaming to a new AP using driver-based SME and roaming trigger,
update proto type, AKMP suite, and pairwise cipher suite based on the
(Re)Association Request frame. Update PMF, group cipher, and group mgmt
cipher based on the AP's RSNE into wpa_sm. group_mgmt_cipher needs to be
updated based on PMF capabilities of STA and roamed AP.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Since the 6 GHz band has no DFS channels, enable 6 GHz 160 MHz bandwidth
as the default configuration for IEEE 802.11s mesh.
example:
network={
ssid="6gmesh160"
key_mgmt=SAE
mode=5
frequency=6275
psk="1234567890"
}
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
IEEE Std 802.11ax-2021 mandates 6 GHz STA to use Management Frame
Protection (MFP) when RSN is enabled.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
