Provide AKM, key length, and information about needed subelements to the
parser function so that the variable length MIC field cases can be
recognized for FT-SAE-EXT-KEY. Knowledge about R0KH-ID/R1KH-ID being
needed is required to be able to iterate over possible MIC field lengths
for the case where the AP does not yet know the correct key length at
the beginning of FT protocol.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Provide AKM to the helper function so that the new SHA256 and SHA512
options can be covered for FT-SAE-EXT-KEY.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Provide key length instead of SHA384/SHA256 selection to the helper
function so that the new SHA512 option can be covered for
FT-SAE-EXT-KEY.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Provide enough information to allow the FTE to be built using the
correct MIC field length based on the used AKM and key length.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Move from this type of constructions:
switch (val) {
case 1:
something;
break;
}
default-action;
into following:
switch (val) {
case 1:
something;
break;
default:
default-action;
break
}
for cases where the switch statement is not expected to contain a full
set of enum values and as such, does not lose value from not having the
default target.
This makes the intent of default behavior clearer for static analyzers like
gcc with -Wswitch-default.
Signed-off-by: Chaoli Zhou <quic_zchaoli@quicinc.com>
Do not include 6 GHz channels in the ACS possible channel list if
neither HE (ieee80211ax=1) nor EHT (ieee80211be=1) is enabled since
those channels cannot be used in such combination.
Signed-off-by: Vishal Miskin <quic_vmiskin@quicinc.com>
hostapd based automatic channel selection doesn't update the hardware
mode after the channel is selected. This change specifically helps
channel 14 which can operate only in IEEE 802.11b mode.
Signed-off-by: Sunil Ravi <sunilravi@google.com>
bss->conf->bssid may be kept unset and will cause an empty BSSID field
in RNR. Fix this to use own_addr instead.
Signed-off-by: Shay Bar <shay.bar@celeno.com>
Signed-off-by: moran.daori <moran.daori@celeno.com>
The ACS info messages frequently appear for multiple channels. Without
the actual frequency in the messages, they are not very informative.
Add the frequency to them to improve this.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Don't select channels designated for exclusive indoor use when the
country string is set for outdoor operation (country3=0x4f, i.e., the
third character of the country string is 'O').
Signed-off-by: David Bauer <mail@david-bauer.net>
Support updating the RRM IEs to the driver for Probe Response and
(Re)Association response frames in the AP mode when the SME is
implemented in the driver.
Signed-off-by: Chaoli Zhou <quic_zchaoli@quicinc.com>
Set TWT responder configurator in the driver parameters only when the AP
is configured with HE enabled. This was already done for the extended
capability bit generation in commit 8de0ff0fa1 ("HE: Add TWT responder
extended capabilities field"), but this parameter for the driver command
to start the AP in _ieee802_11_set_beacon() missed the condition.
Move the ieee80211ax check into the common helper function to cover both
cases. In addition, add a check for disable_11ax to cover the case where
HE is disabled for a specific BSS.
Fixes: ab8c55358e ("HE: Dynamically turn on TWT responder support")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
After the secure association and PTK derivation are completed, if the
device supports LTF keyseed, generate the LTF keyseed using KDK and set
the ranging context to the driver by using the command
QCA_NL80211_VENDOR_SUBCMD_SECURE_RANGING_CONTEXT.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
AP as a responder, on successful completion of PASN authentication
configures the required keys by using the command
QCA_NL80211_VENDOR_SUBCMD_SECURE_RANGING_CONTEXT to the driver.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add an option for an alternative processing of PTKSA life time expiry.
Register a callback in wpa_supplicant to handle the life time expiry of
the keys in PTKSA cache. Send PASN deauthentication when a PTKSA cache
entry expires.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
On successful PASN handshake or 4-way handshake with a peer, PTK is
derived using the local and peer MAC addresses as input. Store the own
MAC address that is used for key derivation in PTKSA cache to maintain
that state over potential MAC addresses changes.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Use separate capabilities for AP and STA modes for P802.11az security
parameters secure LTF support, secure RTT measurement exchange support,
and protection of range negotiation and measurement management frames
support.
P802.11az security parameters are considered to be supported for both
station and AP modes if the driver sets NL80211_EXT_FEATURE_SECURE_LTF,
NL80211_EXT_FEATURE_SECURE_RTT, and
NL80211_EXT_FEATURE_PROT_RANGE_NEGO_AND_MEASURE flags. The driver can
advertize capabilities specific to each mode using
QCA_WLAN_VENDOR_FEATURE_SECURE_LTF*,
QCA_WLAN_VENDOR_FEATURE_SECURE_RTT*, and
QCA_WLAN_VENDOR_FEATURE_PROT_RANGE_NEGO_AND_MEASURE* flags.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Reorder PKEX initiation function to send out the PKEX Exchange Request
frame at the end after all possible error cases have been checked. This
prevents Enrollee from seeing a PKEX frame when the session is about to
fail.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
hostapd_dpp_add_controller() ended up trying to parse the IP address
without nul terminating it. This might work with some C libraries, but
not all. And anyway, this was already supposed to nul terminate the
string since a temporary copy is created of the constant string. Fix
this by adding the missed replacement of the space with nul.
Fixes: bfe3cfc382 ("DPP: Allow Relay connections to Controllers to be added and removed")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This can be helpful for upper layers to be able to determine whether the
configuration was rejected.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The new SAE AKM suites are defined to use H2E, so ignore the sae_pwe
value when these AKM suites are used similarly to the way H2E gets
enabled when SAE Password Identifiers are used.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Define new WPA_KEY_MGMT_* values for the new SAE AKM suite selectors
with variable length keys. This includes updates to various mapping and
checking of the SAE key_mgmt values.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The new DPP-RELAY-NEEDS-CONTROLLER control interface event can be used
to trigger mDNS discovery of a Controller to see if such a connection
can be established automatically at the time an Enrollee is trying to
initiate an operation.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The new control interface commands "DPP_RELAY_ADD_CONTROLLER <IP addr>
<PK hash>" and "DPP_RELAY_REMOVE_CONTROLLER <IP addr>" can now be used
to dynamically add and remove connections to Controllers for the cases
where the connection is initialized through a DPP Public Action frame
(i.e., Controller as the Responder).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Instead of requiring explicit configuration through
dpp_configurator_connectivity=1, advertise Configurator connectivity
automatically if a Relay is configured with a Controller that can
operate as a Responder.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Accept an incoming TCP connection from a Controller in a Relay that is
configured with dpp_relay_port even if that Controller is not configured
with a dpp_controller parameter. This allows more dynamic Controller
initiated operations, e.g., when using mDNS to discover a Relay.
This type of a dynamic Controller entry will not be used for exchanges
that are initiated by an Enrollee (i.e., based on a DPP Public Action
frame received by the Relay).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Verify that the peer does not change its bootstrapping key between the
PKEX exchange and the authentication exchange.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
When PKEX was started through the push button mechanism, the own
bootstrapping key was not bound correctly to the Authentication phase
information and that ended up in incorrectly generating a new
bootstrapping key for the Authentication exchange. Fix this by added the
needed own=<id> parameter into the cached parameters when using push
button.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The peer=<id> information about the specific boostrapping key provided
through PKEX was added for Public Action frame cases, but the TCP
variant did not do same. Add the same information there to maintain
knowledge of the specific peer bootstrapping key from PKEX to
Authentication exchange.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Extend DPP push button support in wpa_supplicant to allow the role of
the Configurator to be used. This provides similar functionality to the
way the DPP_PUSH_BUTTON command in hostapd worked when providing the
configuration parameters with that command (instead of building the
config object based on current AP configuration).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
It is possible for a Controller to receive a copy of its own PKEX
Exchange Request in the case where the Controller is initiating a PKEX
exchange through a Relay. The Configurator role in the device would have
a matching PKEX code in that case and the device might reply as a PKEX
responder which would result in going through the exchange with the
Controller device itself. That is clearly not desired, so recognize this
special case by checking whether the Encrypted Key attribute value
matches a pending locally generated one when processing a received PKEX
Exchange Request.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
We are not supposed to reuse these without being explicitly requested to
perform PKEX again. There is not a strong use case for being able to
provision an Enrollee multiple times with PKEX, so this should have no
issues on the Enrollee. For a Configurator, there might be some use
cases that would benefit from being able to use the same code with
multiple Enrollee devices, e.g., for guess access with a laptop and a
smart phone. That case will now require a new DPP_PKEX_ADD command on
the Configurator after each completion of the provisioning exchange.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a privacy protecting variant of the peer introduction protocol to
allow the station device to hide its Connector from 3rd parties. The new
wpa_supplicant network profile parameter dpp_connector_privacy=1 can be
used to select this alternative mechanism to the peer introduction
protocol added in the initial release of DPP.
It should be noted that the new variant does not work with older DPP APs
(i.e., requires support for release 3). As such, this new variant is
disabled by default.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This allows the DPP Configuration Request Object from an Enrollee to be
extended with 3rd party information. The new dpp_extra_conf_req_name and
dpp_extra_conf_req_value configuration parameters specify the name of
the added JSON node and its contents. For example:
dpp_extra_conf_req_name=org.example
dpp_extra_conf_req_value={"a":1,"b":"test"}
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This extends Relay functionality to allow a Controller to intitiate a
new DPP exchange in addition to the previously supported case where the
exchange was initiated through a DPP Public Action frame.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
While the most likely production use case for DPP push button is to
provision the AP's current configuration, there might be some use cases
for providing different configuration. Add possibility for doing this by
extending the DPP_PUSH_BUTTON command to accept an optional set of
parameters similarly to the other DPP commands for the Configurator.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add support to use a push button -based bootstrap mechanism with DPP.
The new DPP_PUSH_BUTTON control interface command enables this mode on
the AP/hostapd and station/wpa_supplicant. This goes through the
following sequence of events: a suitable peer in active push button mode
is discovered with session overlap detection, PKEX is executed with
bootstrap key hash validation, DPP authentication and configuration
exchanges are performed.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Move most of CHANWIDTH_* definitions from ieee80211_defs.h to defs.h as
the definitions are getting used mostly for internal purpose only. Also
change prefix of the definitions to CONF_OPER_CHWIDTH_* and update in
all the files accordingly.
Leave the couple of VHT-specific exceptions to use the old defines (the
reason why they were originally added as VHT values), to avoid use of
clearly marked configuration values in information elements. In
addition, use the defines instead of magic values where appropriate.
Signed-off-by: Aleti Nageshwar Reddy <quic_anageshw@quicinc.com>
Skip the x_snoop_deinit() operations if hostapd did not actually
configure the parameters in the first place. While clearing these
specific parameters is unlikely to change how they were set outside the
scope of hostapd, it is better to leave them as-is to avoid surprises if
hostapd was not configured to use ProxyARP.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
tcp_addr=from-uri can now be used as a special case for initiating
DPP-over-TCP to the destination indicated in the peer bootstrapping URI.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Only use the bandwidth bits that are applicable for the current
operating band. This avoids use of reserved bits when determining the
length of the Support EHT-MCS And NSS Set field length.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
IEEE Std 802.11-2020 is ambiguous on how the Secure bit is set in
EAPOL-Key msg 1/4 and 2/4 in the case where 4-way handshake is use to
rekey the PTK. 12.7.2 describes this with "set to 1 once the initial key
exchange is complete" while 12.7.6 shows EAPOL-Key msg 1/4 and 2/4 using
Secure=0 without any consideration on whether the handshake is for
rekeying.
TGme seems to be moving towards clarifying this to use Secure=1 based on
there being a shared PTKSA between the Authenticator and the Supplicant.
In other words, this would use Secure=1 in EAPOL-Key msg 1/4 and 2/4 in
the case of rekeying. Change implementation to match that. This bit was
already practically ignored on the reception side, so this should not
have impact on actual functionality beyond this one bit changing its
value in the frame.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Avoid the somewhat confusing mechanism of determining the bitfield index
from the assigned IP address to make this easier for static analyzers.
Signed-off-by: Jouni Malinen <j@w1.fi>
Limit the GAS comeback delay to 60000 TUs, i.e., about 60 seconds. This
is mostly to silence static analyzers that complain about unbounded
value from external sources even though this is clearly bounded by being
a 16-bit value.
Signed-off-by: Jouni Malinen <j@w1.fi>
BIT(r) is not sufficient here since it does not cover 64 bit values.
Write this out with 1ULL to be large enough for the shift operation.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like fst_wpa_obj::get_hw_modes would have been left
uninitialized in hostapd. It is not obviously clear why this would not
have caused issues earlier, but in any case, better make this set
properly to allow unexpected behavior should that function pointer ever
be used.
Signed-off-by: Jouni Malinen <j@w1.fi>
Without this, hostapd generates Probe Response frames with the null
destination address when hostapd enables unsolicited Probe Response
frame transmission. Fix this to use the broadcast address instead.
Fixes: 024b4b2a29 ("AP: Unsolicited broadcast Probe Response configuration")
Signed-off-by: MeiChia Chiu <meichia.chiu@mediatek.com>
RSN design is supposed to encrypt all Data frames, including EAPOL
frames, once the TK has been configured. However, there are deployed
implementations that do not really follow this design and there are
various examples from the older uses of EAPOL frame where those frames
were not encrypted. As such, strict filtering of unencrypted EAPOL
frames might results in undesired interoperation issues.
However, some of the most important cases of missing EAPOL frame
encryption should be possible to handle without causing too significant
issues. These are for cases where an attacker could potentially cause an
existing association to be dropped when PMF is used. EAPOL-Start and
EAPOL-Logoff are potential candidate for such attacks since those frames
could be used to terminate an authentication or initiate a new EAP
authentication. Such an attack could result in the station ending up
disconnecting or at minimum, getting into somewhat mismatching state
with the AP.
Drop EAPOL-Start/Logoff/EAP frames on the AP/Authenticator when it is
known that it was not encrypted but should have been and when PMF is
enabled. While it would be correct to drop this even without PMF, that
does not provide any significant benefit since it is trivial to force
disconnection in no-PMF cases. It should also be noted that not all
drivers provide information about the encryption status of the EAPOL
frames and this change has no impact with drivers that do not indicate
whether the frame was encrypted.
Signed-off-by: Jouni Malinen <j@w1.fi>
This information was already available from the nl80211 control port RX
path, but it was not provided to upper layers within wpa_supplicant and
hostapd. It can be helpful, so parse the information from the driver
event.
Signed-off-by: Jouni Malinen <j@w1.fi>
sm->pairwise_set needs to be set whenever the TK has been configured to
the driver to request following EAPOL frames to be encrypted (or more
specifically, not to request them to not be encrypted). The FILS case
missed this setting and that could result in rekeying or
reauthentication in an associated started with FILS not working
correctly.
Fixes: da24c5aa1c ("FILS: Set TK after association (AP)")
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_validate_wpa_ie() might update sm->* values, so it should not be
allowed for an existing STA entry if that STA has negotiated MFP to be
used for the association. Fix this by first checking whether an SA Query
procedure needs to be initiated. In particular, this prevents a
potential bypass of the disconnection protection.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The driver can consider EHT specific parameters such as the puncture
pattern for ACS when this flag attribute is indicated by userspace.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Do not consider optional octets maximum lengths when validating EHT
fixed fields length. Furthermore, do not use the first two octets of the
PPE Thresholds field without explicitly confirming that these octets
were included in the element and fix PPE Thresholds field length
calculation.
Fixes: a6d1b4c46c ("EHT: Process (Re)Association Request frame capabilities")
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
enum macaddr_acl is forward declared in wpa_supplicant/ap.h.
c++ compiler doesn't allow forward declaration. So to fix the
compilation error, moved the enum macaddr_acl declaration out
of struct hostapd_bss_config.
Signed-off-by: Sunil Ravi <sunilravi@google.com>
Add a notification message to indicate reason for TLS handshake failure
due to the server not supporting safe renegotiation (RFC 5746).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
pbkdf2_sha1() may return errors and this should be checked in calls.
This is especially an issue with FIPS builds because the FIPS
requirement is that the password must be at least 14 characters.
Signed-off-by: Juliusz Sosinowicz <juliusz@wolfssl.com>
Add support for IMSI privacy in the EAP-SIM/AKA server implementation.
If the new hostapd configuration parameter imsi_privacy_key is used to
specify an RSA private key, that key will be used to decrypt encrypted
permanent identity.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Modify hostapd_set_freq_params() to include EHT parameters and update
the calling functions to match.
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Set bit 21 in the neighbor report for an EHT AP as described in IEEE
P802.11be/D1.5, 9.4.2.36. Also move the check for HE outside the check
for HT as neither HT nor VHT are enabled in the 6 GHz band.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Add support for EHT capabilities in the addition of a new station entry
to the driver.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Parse EHT capabilities sent by a non-AP STA in (Re)Association Request
frames. Validate the length of the element, matching MCS rates between
AP TX and STA RX. Store the capabilities in the station info structure.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Add EHT Operation element in Beacon, Probe Response, and (Re)Association
Response frames using the format described in IEEE P802.11be/D1.5,
9.4.2.311.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Add new configuration options to configure EHT operating channel
width and center frequency.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Add compilation support for IEEE 802.11be along with options to enable
EHT support per radio and disable per interface.
Enabling HE is mandatory to enable EHT mode.
Tested-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Allow hostapd configuration to specify use of the 6 GHz band with the
specific op_class values without having to set the hw_mode=a parameter
explicitly.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This feature does not work on all radios that advertise this feature
with the current driver implementation, and possibly some users don't
want to use it even if it works fine, so disable it by default for now,
but let users enable it as desired with enable_background_radar=1.
Signed-off-by: Ben Greear <greearb@candelatech.com>
The acs_exclude_dfs parameter is documented as a way to exclude DFS
channels when performing ACS without disabling DFS altogether. The
problem is this parameter is only enforced when ACS is offloaded to the
driver (WPA_DRIVER_FLAGS_ACS_OFFLOAD). So from now on, lets also check
acs_exclude_dfs in the internal ACS implementation to exclude channels
marked with radar detection.
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
This commit activates the functionality of the previous commits by
handling the actual events that will trigger the CCA process.
Tested-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
While we are doing CCA the BSS Color Disabled field inside the HE
Operation Parameters field needs to be set.
Tested-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
This information element is similar to the CSA one. It contains a
counter and the target color. Once the counter expired, the change to
the new color happens.
Just note the current implementation is based on CCA counter attributes
that only take Beacon and Probe Response framesinto account.
(Re)Association Response frames do not currently have kernel APIs to
decrement the CCA counter since mediatek mcu firmware does not support
it yet and it will be added in future firmware release.
Tested-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Add the core code for handling BSS color collision events and triggering
CCA inside the kernel. The caller of hostapd_switch_color() will be
added in the following commits.
Tested-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Use vendor specific RADIUS attributes for sending ANonce and EAPOL-Key
msg 2/4 for the wpa_psk_radius=3 case. The vendor specific attributes
for this are defined in FreeRADIUS as follows:
BEGIN-VENDOR FreeRADIUS format=Extended-Vendor-Specific-5
ATTRIBUTE FreeRADIUS-802.1X-Anonce 1 octets[32]
ATTRIBUTE FreeRADIUS-802.1X-EAPoL-Key-Msg 2 octets
END-VENDOR FreeRADIUS
Signed-off-by: Jouni Malinen <j@w1.fi>
Add Transmit Power Envelope element for 6 GHz per IEEE Std
802.11ax-2021.
Currently, this uses hard coded EIRP/PSD limits which are applicable to
6 GHz operation in United states, Japan, and Korea. Support to extract
power limits from kernel data will be added after complete regulatory
support is added for the 6 GHz band.
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Add new field definitions for the 6 GHz Operation Information field in
the HE Operation element per IEEE Std 802.11ax-2021, 9.4.2.249. These
will be used for TPC operation in the 6 GHz band.
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
IEEE Std 802.11ax-2021 introduces Regulatory Info subfield to specify
the 6 GHz access point type per regulatory. Add a user config option for
specifying this.
When not specified, Indoor AP type is selected for the 6 GHz AP by
default.
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Add support for the Country element for the 6 GHz band per IEEE Std
802.11ax-2021, 9.4.2.8 (Country element).
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
force_kdk_derivation is defined within CONFIG_TESTING_OPTIONS, so need
to use matching condition when accessing it.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
It could have been possible to get into an endless loop of retried EAP
authentication followed by failing or not completed 4-way handshake if
there was a different interpretation of EAP authentication result
(success on AP, failure on STA). Avoid this by limiting the number of
consecutive EAPOL reauth attempts without completing the following 4-way
handshake.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Unsolicited broadcast Probe Response frame configuration did not work in
hostapd due fils_discovery_min_int being used by mistake where
fils_discovery_max_int should have been used in checking for conflicting
configuration. The latter is the one used to decide whether FILS
discovery is enabled or not.
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
This is a workaround for mac80211 behavior of retransmitting the
Association Request frames multiple times if the link layer retries
(i.e., seq# remains same) fail. The mac80211 initiated retransmission
will use a different seq# and as such, will go through duplicate
detection. If we were to change our DH key for that attempt, there would
be two different DH shared secrets and the STA would likely select the
wrong one.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add an alternative sequence for performing the RADIUS ACL check and PSK
fetch. The previously used (macaddr_acl=2, wpa_psk_radius=2) combination
does this during IEEE 802.11 Authentication frame exchange while the new
option (wpa_psk_radius=3) does this during the 4-way handshake. This
allows some more information to be provided to the RADIUS authentication
server.
Signed-off-by: Jouni Malinen <j@w1.fi>
The check for PSK/passphrase not being present was considering only the
WPA-PSK AKM, but the same check should be applied for all other AKMs
that can use a PSK.
Signed-off-by: Jouni Malinen <j@w1.fi>
While these do not return error code within the current hostapd
implementation, matching functions in wpa_supplicant AP functionality
will have an error case and using consistent return type will make the
control interface code more consistent.
In addition, export hostapd_set_acl() in preparation for the
wpa_supplicant control interface implementation extension.
Signed-off-by: Chaoli Zhou <quic_zchaoli@quicinc.com>
This allows upper layers to learn about associated stations requesting
BSS transition management from the AP.
Signed-off-by: Chaoli Zhou <quic_zchaoli@quicinc.com>
Only the SME-in-hostapd case updated sta->ext_capability while the
SME-in-the-driver case updated sta->qos_map_enabled, but not other items
related to the extended capabilities. This resulted in reduced
information being available through the control interface.
Use the shared helper function for both cases to get matching
information available regardless of the SME architecture.
Signed-off-by: Chaoli Zhou <quic_zchaoli@quicinc.com>
On radar detection on the main chain switch to the channel monitored
by the background chain if we have already performed the CAC there.
If a radar pattern is reported on the background chain, just select a
new random channel according to the regulations for monitoring.
Tested-by: Owen Peng <owen.peng@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Rely on hostapd_dfs_request_channel_switch() to enable CSA for
background radar detection switching back to the selected channel.
Tested-by: Owen Peng <owen.peng@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
This is a preliminary patch to add Channel Switch Announcement for
background radar detection.
Tested-by: Owen Peng <owen.peng@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Introduce the capability to perform radar/CAC detection on an offchannel
radar chain available on some hardware (e.g., mt7915). This feature
allows to avoid CAC downtime switching on a different channel during CAC
detection on the selected radar channel.
Tested-by: Owen Peng <owen.peng@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Add the capability to specify all 3 channel type possibilities in
dfs_downgrade_bandwidth(). This is a preliminary change to introduce
radar/CAC background detection support.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
There can be some discrepancy between the theorical dfs cac end (as
computed with the cac duration and cac start) and the actual cac end as
reported by the driver. During that window, the value of remaining time
outputed by the status command on the socket control interface will
display an overflowed, invalid value.
To mitigate this lets compute the remaining time as signed and display
it only when positive, otherwise defaulting it to 0.
Status command shows something like that when polling every seconds:
state=DFS
cac_time_seconds=60
cac_time_left_seconds=1
...
state=DFS
cac_time_seconds=60
cac_time_left_seconds=0
...
state=DFS
cac_time_seconds=60
cac_time_left_seconds=4294967294
...
state=DFS
cac_time_seconds=60
cac_time_left_seconds=4294967293
...
state=DFS
cac_time_seconds=60
cac_time_left_seconds=4294967292
...
state=ENABLED
cac_time_seconds=60
cac_time_left_seconds=N/A
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
Allow the Configurator to be configured to use a specific curve for the
netAccessKey so that it can request the Enrollee to generate a new key
during the configuration exchange to allow a compatible Connector to be
generated when the network uses a different curve than the protocol keys
used during the authentication exchange.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Allow PKEX v1-only or v2-only behavior to be specific for the Responder
role. This is mainly for testing purposes.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Allow the first Tunnel-Password RADIUS entry to be used for SAE in
addition to the sae_password entries and wpa_passphrase parameters from
the static configuration file.
Signed-off-by: Mario Hros <git@reversity.org>
Introduce type parameter to dfs_get_valid_channel() routine to allow
selection of a radar-only channel where the CAC detection has not been
performed yet. This is a preliminary patch to enable background
radar/CAC detection.
Tested-by: Owen Peng <owen.peng@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
This is a preliminary change to introduce radar/CAC background detection
support.
Tested-by: Owen Peng <owen.peng@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Do not use the first octet of the PPE Thresholds field without
explicitly confirming that that octet was included in the element.
Furthermore, allow the received element to have additional octets in the
end since IEEE Std 802.11ax-2021 defines this to be an extensible
element and new fields could be added to the end of it in the future.
Fixes: 0497e41481 ("HE: Fix HE Capabilities element size")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The previously used calculation was not correct for the cases where the
extra padding field was needed. Fix this by properly calculating the
number of full octets in the field.
Fixes: 0497e41481 ("HE: Fix HE Capabilities element size")
Signed-off-by: Shiva Sankar Gajula <quic_sgajula@quicinc.com>
Couple of the WPS/P2P/RADIUS-PSK cases were freeing heap memory
allocations without explicitly clearing the PSK value. Add such clearing
for these to avoid leaving the PSK in memory after it is not needed
anymore.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Unlike the other keys that were cleared here, the PMK is available
without FT support built into hostapd and as such, should be cleared in
all cases.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This makes it easier to scan process memory for key information that is
not supposed to remain there after the last use.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Allow macsec_csindex to be configured and select the cipher suite when
the participant acts as a key server.
Signed-off-by: leiwei <quic_leiwei@quicinc.com>
Check driver support for SA Query offload in AP mode and skip starting
SA Query timer on CSA for OCV enabled STAs when the driver indicates
support for offloading SA Query procedures.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The TCP code path did not handle the postponed connection attempt on TX
status and the following result message from the Enrollee to the
Configurator. Fix this by adding TCP-versions of these operations to
match the way wpa_supplicant implemented this for the Public Action
frames.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This extends dpp_test functionality to allow DPP Network Introduction
exchanges to use an incorrect value in the Protocol Version attribute.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Use a separate ver=<1|2> parameter to DPP_PKEX_ADD instead of
overloading init=1 with version indication. This allows additional
options for forcing v1-only and v2-only in addition to automatic mode
(start with v2 and fall back to v1, if needed).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This extends hostapd with the design used in wpa_supplicant for PKEX
initiator retries and automatic version fallback from v2 to v1 (the
latter is enabled only with CONFIG_DPP3=y).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Report TX status for DPP messages even if the destination address was
broadcast. This is needed to get appropriate trigger for PKEX retries.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The rx_freq of Public Action frame was not maintained by the GO and the
GO always sent the response on the operating channel. This causes
provision discovery failure when a P2P Device is sending a PD Request on
a 2.4 GHz social channel and the GO is responding on a 5 GHz operating
channel.
Save the rx_freq and use it for GO to sent the response. This extends
commit c5cc7a59ac ("Report offchannel RX frame frequency to hostapd")
to cover additional frame types.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
hostapd should update Supported Channel Width Set of HT Capability
Information field after channel switching done. Otherwise, it would
continue to use the old setting.
Signed-off-by: peterhuang <peterhuang@realtek.com>
Because ieee80211ac and ieee80211ax were not updated before channel
switch is done, hostapd didn't build the Channel Switch Wrapper element
when it switched from HT to bandwidth more than 40 MHz of VHT/HE. fix
this by allowing hostapd_eid_wb_chsw_wrapper() to determine internally
when the element needs to be added based on the new channel instead of
the old configuration.
Signed-off-by: peterhuang <peterhuang@realtek.com>
hostapd will build wrong beacon_after in hostapd_fill_csa_settings() if
it doesn't update ieee80211ac when channel switching.
Signed-off-by: peterhuang <peterhuang@realtek.com>
Allow mesh_fwding (dot11MeshForwarding) to be specified in a mesh BSS
config, pass that to the driver (only nl80211 implemented for now) and
announce forwarding capability accordingly.
Signed-off-by: José Pekkarinen <jose.pekkarinen@unikie.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
If min_tx_power is specified (default 0 dBm, i.e., no constraint), ACS
and DFS will not consider channels whose available max_tx_power is less
than the configured value.
This may be useful to exclude SRD (Short Range Device) channels which
may be limited to 13.9 dBm (25 mW) in some regulatory domains.
Signed-off-by: Alan Young <consult.awy@gmail.com>
Add support for PKEXv2 core protocol. This defines a new PKEX Exchange
Request message type with protocol negotiation and different rules for
key derivation with PKEXv2 or newer is used.
This does not change existing behavior for PKEX, i.e., the PKEXv1
variant will still be used by default.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Allow the dpp_test parameter to be used to request the Protocol Version
attributed to be omitted from the Peer Discovery Request/Response
message.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Verify that the Protocol Version attribute is used appropriate in Peer
Discovery Request/Response messages in cases where the signed Connector
includes the version information.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Generate Peer Discovery Request/Response messages using the protected
version from the Connector, if present, instead of the currently
supported protocol version which might be higher than the one that got
included into the signed Connector during provisioning earlier.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Reduced neighbor report has a field to indicate whether unsolicited
Probe Response transmission is active. Add a check to return failure if
both FILS discovery and unsolicited Probe Response are enabled at the
same time to ensure that RNR includes valid data.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
When a Probe Request frame from a station includes an SSID matching that
of a co-located 6 GHz AP, AP should respond with a Probe Response frame
that includes Reduced Neighbor Report element containing information
regarding the requested BSS.
Signed-off-by: Muna Sinada <msinada@codeaurora.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Update 2.4/5 GHz Beacon frames every time Beacon frames for co-located 6
GHz AP(s) are set. This is required for 6 GHz out-of-band discovery so
that lower band Beacon frames will include RNR element with 6 GHz AP
information irrespective of the AP bring-up order. Similarly, RNR is
included in FILS Discovery frames by default in 6 GHz-only mode,
updating the Beacon frames will remove it when co-located 2.4/5 GHz
interfaces are brought up.
This change also ensures that the changes in 6 GHz AP configuration such
as new channel and bandwidth get reflected in the lower bands Beacon
frames.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Add Reduced Neighbor Report element in Beacon, Probe Response, and FILS
Discovery frames.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Include Reduced Neighbor Report element in Beacon and Probe Response
frames by default if the reporting AP is 2.4/5 GHz and it is co-located
with a 6 GHz AP. Similarly, include RNR by default in FILS Discovery
frames if the AP is a standalone 6 GHz AP.
Signed-off-by: John Crispin <john@phrozen.org>
Co-developed-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Calculate the length and include data for the BSSes active on the same
radio as the reporting BSS in the Reduced Neighbor Report element. This
element is included in Beacon and Probe Response frames.
Signed-off-by: John Crispin <john@phrozen.org>
Co-developed-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Co-developed-by: Muna Sinada <msinada@codeaurora.org>
Signed-off-by: Muna Sinada <msinada@codeaurora.org>
Co-developed-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Include data from the existing neighbor database in the Reduced Neighbor
Report element in Beacon frames if the configuration option 'rnr' is
enabled for the BSS.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Muna Sinada <msinada@codeaurora.org>
Co-developed-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Adds configuration option 'rnr' to enable the reduced neighbor report
elements in Beacon and Probe Response frames.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Add a new field to include BSS Parameter subfield in the neighbor
database as described in IEEE Std 802.11ax-2021, Figure 9-632a (BSS
Parameters subfield format). This field holds information related to
multiple BSSID, access point co-location, and 20 TU probe response
active/inactive state.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Calculate and store short SSID in hostapd_data context during config
load time and in neighbor report.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Adds the ability to specify the dialog token of a WNM BSS Transition
Management Request frame via the hostapd control interface.
For this, the new 'dialog_token' option can be used with the BSS_TM_REQ
command. It accepts values as an 8 bit unsigned integer. If not
specified, the dialog token is set to 1 like before.
Signed-off-by: David Bauer <mail@david-bauer.net>
Stop the DPP Controller instance, if one is started, when the hostapd
interface that was used to start that Controller is removed. This is
needed to remove the control pointers that point to the soon-to-be-freed
hostapd structures. This fixes an issue where a Controller operation
with multiple interfaces could have resulted in references to freed
memory if an interface is removed without explicitly stopping the DPP
Controller.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The disable_dgaf config field is only available in case hostapd is
compiled with Hotspot 2.0 support (CONFIG_HS20=y), however Proxy-ARP
(CONFIG_PROXYARP=y) does not depend on Hotspot 2.0.
Only add the code related to this config field when Hotspot 2.0 is
enabled to fix compilation with the aformentioned preconditions.
Signed-off-by: David Bauer <mail@david-bauer.net>
Replaced the word "sanity" with the inclusive word "validity". The
comment in acs_survey_interference_factor() was referring a function
that does not exist, so remove it instead of trying rename the function.
Signed-off-by: Arowa Suliman <arowa@chromium.org>
Commit 0cb39f4fd5 ("HE: Extend BSS color support") sets the BSS Color
default value to 1 as "Interoperability testing showed that stations
will require a BSS color to be set even if the feature is disabled."
A new interop issue was observed with hardcoded BSS color value of 1:
- REF device using one interface (e.g., wlan0) to connect to an HE
AP, whose BSS color is enabled and value is 1.
- REF device using another interface (e.g., p2p0) to connect to a
P2P GO using BSS color default settings.
(i.e., BSS color disabled and value is 1).
- REF device checks both AP's and P2P GO's BSS Color values even though
GO's BSS color is disabled. This causes collision of the BSS
color somehow causing RX problems.
For DUT as a P2P GO, its firmware uses default BSS color value 1 from
wpa_supplicant, then triggers a timer (e.g., 120 s) to update its BSS
color values based on its neighboring BSSes. To reduce the likelihood of
BSS color collision with REF device before that, use a random BSS Color
if not defined in the config file.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Channel 100 is a valid channel to choose for 80 MHz operation. However,
it was converted to 5500 MHz, not 5550 MHz, for the 80 MHz case while
the conversion to other bandwidths was done correctly. In fact, there is
no channel assigned to this frequency 5550 MHz.
Fix this obvious typo to allow ACS to select channel 100 for 80 MHz
operation again.
Fixes: bef5eee4f7 ("Convert channel to frequency based selection for AP mode ACS")
Signed-off-by: David Bauer <mail@david-bauer.net>
For the function hostapd_get_sta_tx_rx(), the name
hostapd_get_sta_info() is more appropriate as it is also responsible for
getting many other STA specific params like RSSI, inactive milliseconds
along with TX and RX bytes.
Signed-off-by: Gokul Sivakumar <gokulkumar792@gmail.com>
When a Mesh interface is managed by wpa_supplicant, include the peer
link connected time (secs) in the output of "sta <addr>", "all_sta"
wpa_cli cmds for each peer. This will be helpful to find when the peer
link connection got established. The NL80211_STA_INFO_CONNECTED_TIME
netlink attribute data is used for this purpose if available.
$ wpa_cli -i mesh0 all_sta
02:00:00:00:02:00
flags=[ASSOC][WMM][HT]
aid=1
capability=0x0
listen_interval=0
supported_rates=82 84 8b 96 8c 12 98 24 b0 48 60 6c
timeout_next=NULLFUNC POLL
rx_packets=77
tx_packets=3
rx_bytes=8510
tx_bytes=284
inactive_msec=104
signal=-30
rx_rate_info=65 mcs 0
tx_rate_info=65 mcs 0
ht_mcs_bitmask=ffff0000000000000000
connected_time=24
ht_caps_info=0x103c
The connected_time field in the output of "hostapd_cli -i ap0 all_sta"
cmd is not affected and it will continue to show the connected time
maintained by hostapd for each STA.
Signed-off-by: Gokul Sivakumar <gokulkumar792@gmail.com>
../src/ap/ieee802_11.c: In function ‘pasn_wd_handle_sae_commit’:
../src/ap/ieee802_11.c:2401:60: warning: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 3 has type ‘size_t’ {aka ‘unsigned int’} [-Wformat=]
wpa_printf(MSG_DEBUG, "PASN: SAE buffer too short. len=%lu",
~~^
%u
buf_len);
~~~~~~~
../src/ap/ieee802_11.c: In function ‘pasn_wd_handle_sae_confirm’:
../src/ap/ieee802_11.c:2477:60: warning: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 3 has type ‘size_t’ {aka ‘unsigned int’} [-Wformat=]
wpa_printf(MSG_DEBUG, "PASN: SAE buffer too short. len=%lu",
~~^
%u
buf_len);
~~~~~~~
../src/ap/ieee802_11.c: In function ‘pasn_wd_handle_fils’:
../src/ap/ieee802_11.c:2707:62: warning: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 3 has type ‘size_t’ {aka ‘unsigned int’} [-Wformat=]
wpa_printf(MSG_DEBUG, "PASN: FILS: Buffer too short. len=%lu",
~~^
%u
buf_len);
~~~~~~~
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
When the driver provides a list of supported modes, hostapd ended up
adding channel 6 even if the 2.4 GHz mode was not included. This
resulted in incorrect behavior of trying to transmit on a not supported
channel in case of 5 GHz only radios.
Fix this by adding the channel 6 by default only if the driver does not
provide a list of supported modes. Whenever the supported modes are
available, only add this channel if it is explicitly listed as an
enabled channel.
This is similar to an earlier wpa_supplicant change in commit
8e5739c3ac ("DPP2: Check channel 6 validity before adding it to chirp
channel list").
Signed-off-by: Disha Das <dishad@codeaurora.org>
IEEE Std 802.11-2016, 12.4.7.6 specifies:
An SAE Commit message with a status code not equal to SUCCESS shall
indicate that a peer rejects a previously sent SAE Commit message.
An SAE Confirm message, with a status code not equal to SUCCESS, shall
indicate that a peer rejects a previously sent SAE Confirm message.
Thus when SAE authentication failure happens, authentication transaction
sequence number should not be incremented.
Signed-off-by: Jia Ding <jiad@codeaurora.org>
Some of the reconfiguration cases (e.g., with WPS reconfiguration
enabling WPA/WPA2) might end up calling hostapd_setup_wpa() twice
without calling hostapd_deinit_wpa() in the middle. This would have
resulted in a memory leak since the PTKSA cache was being reinitialized
without freeing previous memory allocation.
Fix this by making PTKSA cachine initialization independent of
hapd->wpa_auth so that reinitialization does not happen in a manner that
would have overridden the old hapd->ptksa pointer without freeing the
referenced resources.
Fixes: f2f8e4f458 ("Add PTKSA cache to hostapd")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use WPA3-Personal (SAE+PMF) for P2P connections in the 6 GHz band to
enable the Wi-Fi Display use case on the 6 GHz band without having to
use WPA2-Personal (PSK) on that new band.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
hostapd_handle_dfs_offload() is the DFS handler for the offloaded case,
in which ieee80211_is_dfs() is used to check if the configured frequency
requires DFS or not.
When the configured channel width is not 20 (e.g., 160),
ieee80211_is_dfs() will not checked adjacent freqs, so it possibly makes
wrong conclusion for whether DFS is required.
hostapd_is_dfs_required() does similar thing with ieee80211_is_dfs()
except it supports checking whether the configured frequency and its
adjacent frequencies require DFS. So hostapd_is_dfs_required() is a more
robust and better option than ieee80211_is_dfs() to check DFS.
The issue is hostapd_is_dfs_required() is for non-offload case due to
the check of the configuration parameter ieee80211h. Add a check for
WPA_DRIVER_FLAGS_DFS_OFFLOAD to make it support the DFS offload case
(i.e., ieee80211h=0) as well.
For example, configuring the AP to start at freq=5240 with channel width
160:
- Existing hostapd checks freq=5240 is non-DFS, hence skip DFS CAC and
transition to AP-Enabled which volatiles DFS-RADAR detection.
LOG: "hostapd : hostapd_handle_dfs_offload: freq 5240 MHz does not
require DFS. Continue channel/AP setup"
- This commit checks freq=5240 and its adjacent freqs are DFS required,
hence remains in DFS state until DFS CAC completed.
LOG: "hostapd : hostapd_handle_dfs_offload: freq 5240 MHz requires
DFS for 4 chans"
Signed-off-by: Hu Wang <huw@codeaurora.org>
When regulatory rules are configured not to support 40 MHz channels on
the 2.4 GHz band, hostapd_is_usable_chans() still allowed 40 MHz
channels (i.e., 1-9) to be used with ht_capab=[HT40+][HT40-].
Looking into hostapd_is_usable_chans():
1) Validate primary channel using hostapd_is_usable_chan()
2) Try to pick a default secondary channel if hostapd_is_usable_chan()
3) Try to pick a valid secondary channel if both HT40+/HT40- set, and
further validate primary channel's allowed bandwidth mask.
4) Return channel not usable.
For example, for the 2.4 GHz channel 9 in Japan, its default secondary
channel is 13, which is valid per hostapd_is_usable_chan(), so step (2)
returns channel usable.
Add a more strict check to step (2) to clearly reject 40 MHz channel
configuration if regulatory rules do not allow the 40 MHz bandwidth,
which is similarly done in commit ce6d9ce15b ("hostapd: Add supported
channel bandwidth checking infrastructure").
Signed-off-by: Hu Wang <huw@codeaurora.org>
Add user configuration he_twt_responder for enabling/disabling TWT
responder role, in addition to checking the driver's capability. The
default configuration is to enable TWT responder role when the driver
supports this.
Signed-off-by: Mohammad Asaad Akram <asadkrm@codeaurora.org>
FILS authentication derives PMK differently from the EAP cases. The PMK
value does not bind in the MAC addresses of the STAs. As such, the same
PMKID is used with different BSSIDs. Fix both the hostapd and
wpa_supplicant to use the previous PMKID as is for OKC instead of
deriving a new PMKID using an incorrect derivation method when using an
FILS AKM.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
This makes it easier for test scripts to track completion of 4-way
handshake from hostapd, e.g., when going through PTK rekeying.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This makes it convenient for an external test script to use
ext_eapol_frame_io=1 to delay and/or modify transmission of EAPOL-Key
msg 1/4 without having to use separate frame injection mechanisms.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
"REKEY_PTK <STA MAC address>" can now be used to force rekeying of the
PTK for the specified associated STA.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do not start yet another rekeying of GTK when receiving an EAPOL-Key
request frame at the point when the GTK is already being rekeyed. This
fixes issues where the AP might end up configuring a different GTK than
the one it sends to the associated stations.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Determine bandwidth from op_class parameter when set in config. When not
configured, use he_oper_chwidth for determining 80 MHz or 160 MHz. When
both are not set, fall back to 20 MHz by default. This helps in removing
the dependency on op_class parameter in 6 GHz ACS.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Add support for the 6 GHz frequencies using 40, 80, and 160 MHz
bandwidths in the AP mode ACS.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Convert channel based selection to frequency based selection for AP mode
ACS to accommodate for the 6 GHz band needs.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Previously, the secondary channel was set only in presence of HT
capabilities based on HT40+ or HT40-. As HT capabilities and
secondary_channel are not present for the 6 GHz bamd, this causes
incorrect operating class indication in the Supported Operating Classes
element.
Fix this by assigning the secondary channel for bandwidths greater than
20 MHz in the 6 GHz band.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
In the 6 GHz Operation Information field, the Channel Center Frequency
Segment 0 field indicates the channel center frequency index for
the 20 MHz, 40 MHz, 80 MHz, or 80+80 MHz channel on which the
BSS operates in the 6 GHz band. If the BSS channel width is 160 MHz
then the Channel Center Frequency Segment 0 field indicates the
channel center frequency index of the primary 80 MHz.
The Channel Center Frequency Segment 1 field indicates the channel
center frequency index of the 160 MHz channel on which the BSS operates
in the 6 GHz band or the channel center frequency of the secondary 80
MHz for the 80+80 MHz channel.
Since Channel Center Frequency Segment 1 was 0 for 160 MHz, 6 GHz STA
associated using 80 MHz. Update seg0 and seg1 fields per standard (IEEE
P802.11ax/D8.0: 9.4.2.249 HE Operation element).
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
When WMM is disabled, HT/VHT/HE capabilities should not be used for any
STA. If any STA advertises these capabilities, hostapd AP disables HT
capabilities in STA flags during STA assoc, but VHT/HE was not handled
similarly. This could allow a STA to associate in VHT/HE mode even in
WMM disable case.
To avoid this, disable VHT/HE capabilities similarly to HT during STA
association, if WMM is not enabled by the STA.
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
The hostapd process crashed when the UPDATE_BEACON control interface
command was issue after the interface was disabled. Check for this case
and return an error if the interface is disabled.
Signed-off-by: Kani M <kanisumi@codeaurora.org>
Get the DPP Relay Controller context from the list of configured
Controllers based on the correct hostapd callback context. This is
needed to pick the correct hostapd interface for sending out the
response over air, e.g., when the same hostapd process controls a 2.4
GHz only and a 5 GHz only interface.
Signed-off-by: Disha Das <dishad@codeaurora.org>
Simplify the implementation by using shared functions for parsing the
capabilities instead of using various similar but not exactly identical
checks throughout the implementation.
Signed-off-by: Jouni Malinen <j@w1.fi>
IEEE Std 802.11-2020 mandates H2E to be used whenever an SAE password
identifier is used. While this was already covered in the
implementation, the sae_prepare_commit() function still included an
argument for specifying the password identifier since that was used in
an old test vector. Now that that test vector has been updated, there is
no more need for this argument anymore. Simplify the older non-H2E case
to not pass through a pointer to the (not really used) password
identifier.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do so for both wpa_supplicant and hostapd. While this was not explicitly
required in IEEE P802.11az/D3.0, likely direction for the draft is to
start requiring use of H2E for all cases where SAE is used with PASN.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When a PTK derivation is done as part of PASN authentication flow, a KDK
derivation should be done if and only if the higher layer protocol is
supported by both parties.
Fix the code accordingly, so KDK would be derived if and only if both
sides support Secure LTF.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
If WMM is not set explicitly in the configuration, it can be set based
on HT/HE config. As HE can be used without HT/VHT (which was introduced
as a special behavior for the 6 GHz band), add a similar automatic
enabling of WMM for HE without HT.
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Previous debug print used IGTK instead of BIGTK, so fix that to use the
correct key. Actual generation of the BIGTK subelement itself was using
the correct key, though, so this is only needed to fix the debug print.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd configuration parameters ext_capa_mask and ext_capa can
now be used to mask out or add extended capability bits. While this is
not without CONFIG_TESTING_OPTIONS, the main use case for this is for
testing purposes.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to determine the exact length of the element before
filling in the octets since this function is already capable of
truncated the fields based on what the actual values are.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reuse the SAE anti-clogging token implementation to support similar
design with the PASN comeback cookie.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The GAS client processing of the response callback for DPP did not
properly check for GAS query success. This could result in trying to
check the Advertisement Protocol information in failure cases where that
information is not available and that would have resulted in
dereferencing a NULL pointer. Fix this by checking the GAS query result
before processing with processing of the response.
This is similar to the earlier wpa_supplicant fix in commit 931f7ff656
("DPP: Fix GAS client error case handling").
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible to receive the Configuration Request frame before having
seen TX status for the Authentication Confirm. In that sequence, the
DPP-AUTH-SUCCESS event would not be indicated before processing the
configuration step and that could confuse upper layers that follow the
details of the DPP exchange. As a workaround, indicate DPP-AUTH-SUCCESS
when receiving the Configuration Request since the Enrollee/Responser
has clearly receive the Authentication Confirm even if the TX status for
it has not been received.
This was already done in wpa_supplicant in commit 422e73d623 ("DPP:
Indicate authentication success on ConfReqRX if needed") and matching
changes are now added to hostapd.
Signed-off-by: Jouni Malinen <j@w1.fi>
The waiting_conn_status_result flag was not set which made hostapd
discard the Connection Status Result. Fix this to match the
wpa_supplicant implementation.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a new testing parameter to allow airtime policy implementation to be
tested for more coverage even without kernel driver support.
Signed-off-by: Jouni Malinen <j@w1.fi>
When a Deauthentication frame is received, clear the corresponding PTKSA
cache entry for the given station, to invalidate previous PTK
information.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The anti-clogging code was under CONFIG_SAE. Change this so it can be
used both with CONFIG_SAE and CONFIG_PASN.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
PASN authentication mandates support for comeback flow, which
among others can be used for anti-clogging purposes.
As the SAE support for anti clogging can also be used for PASN,
start modifying the source code so the anti clogging support
can be used for both SAE and PASN.
As a start, rename some variables/functions etc. so that they would not
be SAE specific. The configuration variable is also renamed, but the old
version remains available for backwards compatibility.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
For testing purposes, add support for corrupting the MIC in PASN
Authentication frames for both wpa_supplicant and hostapd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When a public key is included in the PASN Parameters element, it should
be encoded using the RFC 5480 conventions, and thus the first octet of
the Ephemeral Public Key field should indicate whether the public key is
compressed and the actual key part starts from the second octet.
Fix the implementation to properly adhere to the convention
requirements for both wpa_supplicant and hostapd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
As defined in IEEE P802.11az/D3.0, 12.12.3.2 for the second PASN frame.
This was previously covered only for the case when the explicit PMKSA
was provided to the helper function. Extend that to cover the PMKID from
SAE/FILS authentication cases.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This function can get called with hapd->wpa_auth == NULL from the
control interface handler, so explicitly check for that.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is needed to be able to move from 80 MHz or lower bandwidth to 160
or 80+80 MHz bandwidth (and back) properly without leaving the Beacon
frame VHT elements showing incorrect information.
Signed-off-by: Jouni Malinen <j@w1.fi>
While it does not look like the stale pointer could have been
dereferenced in practice, it is better not to leave the stale pointer to
freed memory in place to avoid accidental uses.
Signed-off-by: Jouni Malinen <j@w1.fi>
hapd->tmp_eap_user needs to be cleared on interface deinit to avoid
leaving stale pointers to freed memory.
Fixes: ee431d77a5 ("Add preliminary support for using SQLite for eap_user database")
Signed-off-by: Jouni Malinen <j@w1.fi>
When an interface is disabled, e.g. due to radar detected,
hapd->time_adv is freed by hostapd_free_hapd_data(), but later
used by ieee802_11_build_ap_params() calling hostapd_eid_time_adv().
Thus hapd->time_adv needs to be cleared as well.
Fixes: 39b97072b2 ("Add support for Time Advertisement")
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Commit f1df4fbfc7 ("mesh: Use setup completion callback to complete
mesh join") added a check for iface->conf being NULL into a debug print.
However, it is not clear how that could be NULL here. In any case,
setup_interface() could end up dereferencing iface->conf in the call to
hostapd_validate_bssid_configuration(), so better be consistent with the
checks and not get warnings from static analyzers regardless of whether
this can happen in practice.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no point in trying to build in rest of this function if in the
middle of it the CONFIG_NO_RADIUS case would unconditionally fail.
Simply make all of this be conditional on that build parameter not being
set to make things easier for static analyzers.
Signed-off-by: Jouni Malinen <j@w1.fi>
The value from the initial RSN_CIPHER_SUITE_NO_GROUP_ADDRESSED check
ended up getting overridden with the following if. This was supposed to
be a single if statement to avoid that.
Fixes: 9c02a0f5a6 ("FILS: Add generation of FILS Discovery frame template")
Signed-off-by: Jouni Malinen <j@w1.fi>
These frames are used for verifying that a specific SA and protected
link is in functional state between two devices. The IEEE 802.11
standard defines only a case that uses individual MAC address as the
destination. While there is no explicit rule on the receiver to ignore
other cases, it seems safer to make sure group-addressed frames do not
end up resulting in undesired behavior. As such, drop such frames
instead of interpreting them as valid SA Query Request/Response.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Allow the RADIUS client socket to be bound to a specific netdev. This
helps hostapd work better in VRF and other fancy network environments.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Andreas Tobler <andreas.tobler at onway.ch>
Add DRIVER command support on hostapd and hostapd_cli on Android
similarly to the way this previously enabled in wpa_supplicant and
wpa_cli.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Reordering of code in handle_auth_cb() when adding support for full
station state messaged up frame length checks. The length was originally
tested before looking at the payload of the frame and that is obviously
the correct location for that check. The location after those full state
state changes was after having read six octets of the payload which did
not help at all since there was no addition accesses to the payload
after that check.
Move the payload length check to appropriate place to get this extra
level of protection behaving in the expected manner. Since this is a TX
status callback handler, the frame payload is from a locally generated
Authentication frame and as such, it will be long enough to include
these fields in production use cases. Anyway, better keep this check in
working condition.
Fixes: bb598c3bdd ("AP: Add support for full station state")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The capability bit index should not be shifted here as the shifting is
handled later below when building the RSNXE octets.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
When the driver SME is used, offloaded handshakes which need Operating
Channel Validation (OCV) such as SA Query procedure, etc. would fail if
hostapd enables OCV based on configuration but the driver doesn't
support OCV. To avoid this when driver SME is used, enable OCV from
hostapd only when the driver indicates support for OCV.
This commit also adds a capability flag to indicate whether driver SME
is used in AP mode.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Enabling beacon protection will cause STA connection/AP setup failures
if the driver doesn't support beacon protection. To avoid this, check
the driver capability before enabling beacon protection.
This commit also adds a capability flag to indicate beacon protection
support in client mode only.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
At least the ACS case of an attempt to pick a 40 MHz channel on the 2.4
GHz band could fail if HE was enabled and the driver did not include
support for 40 MHz channel bandwidth on the 2.4 GHz band in HE
capabilities. This resulted in "40 MHz channel width is not supported in
2.4 GHz" message when trying to configure the channel and failure to
start the AP.
Avoid this by automatically falling back to using 20 MHz bandwidth as
part of channel parameter determination at the end of the ACS procedure.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When auto channel selection (ACS) is used for HE 40 MHz in the 2.4 GHz
band, AP sets center frequency after finding a 40 MHz channel and then
runs a scan for overlapping BSSes in neighboring channels. Upon OBSS
detection, AP should downgrade to 20 MHz bandwidth.
This was broken because allowed_ht40_channel_pair() returns true in this
case and the steps to reset center frequency are not executed causing
failure to bring interface up.
Fix the condition to allow rollback to 20 MHz.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Add hostapd configuration options for unsolicited broadcast
Probe Response transmission for in-band discovery in 6 GHz.
Maximum allowed packet interval is 20 TUs (IEEE P802.11ax/D8.0
26.17.2.3.2, AP behavior for fast passive scanning).
Setting value to 0 disables the transmission.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
This makes the error message easier to understand if the AP mode setup
failure is caused by invalid secondary channel configuration while the
primary channel is valid.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add hostapd configuration parameters for FILS Discovery frame
transmission interval and prepare a template for FILS Discovery frame
for the driver interface. The actual driver interface changes are not
included in this commit.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
This information is needed in more than one place, so add a helper
function to avoid need to duplicate this code.
Signed-off-by: Jouni Malinen <j@w1.fi>
A similar change was previously done for Probe Response frames, but the
Beacon frame case was missed. Fix this to remove the VHT elements also
from Beacon frames on the 6 GHz since the relevant information is
included only in the HE elements on that band.
Fixes: 49e95ee1ee ("AP: Publish only HE capabilities and operation IEs on 6 GHz band")
Signed-off-by: Jouni Malinen <j@w1.fi>
According to IEEE P802.11ax/D8.0, add Transmit Power Envelope element
into Beacon and Probe Response frames when operating HE AP on the 6 GHz
band.
Signed-off-by: Shay Bar <shay.bar@celeno.com>
hostapd_get_oper_chwidth(iconf) instead of direct access to
iface->conf->vht_oper_chwidth is needed here to be able to use this with
HE in cases where VHT is not enabled.
Signed-off-by: Shay Bar <shay.bar@celeno.com>
According to latest IEEE 802.11 standard, Transmit Power Envelope
element is also relevant to IEEE 802.11ax and is no longer called VHT
Transmit Power Envelope. Remove the VHT naming from the element and move
hostapd_eid_txpower_envelope() from ieee802_11_vht.c to ieee802_11.c in
preparation of using it with HE.
Signed-off-by: Shay Bar <shay.bar@celeno.com>
The Authentication Request frames triggered by the reception of a
Presence Announcement frame were sent to the broadcast address. This is
not correct behavior since the source MAC address of the Presence
Announcement frame was supposed to override the Responder MAC address.
Fix this by using that source MAC address to avoid unnecessary use of
broadcast frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new status code values for SAE H2E and PK resulted in the
sta->added_unassoc cases incorrectly removing the STA entry after
successful SAE commit messages. Fix this by using sae_status_success()
instead of direct check for WLAN_STATUS_SUCCESS when processing SAE
commit messages before removing station entry.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
There are 2 HW modes with IEEE80211_MODE_A: one for the 5 GHz channels
and one for 6 GHz channels. Since hw_get_chan() checks all the
compatible hw modes, eventually, an incorrect hw mode is selected.
To fix this, add a function that checks if a specific mode supports
the requested frequency and if so use it as the current mode.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Extend SPR element to support following fields and pass all
information to kernel for driver use.
* Non-SRG OBSS PD Max Offset
* SRG BSS Color Bitmap
* SRG Partial BSSID Bitmap
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Enable user to configure Maximum MPDU Length, Maximum A-MPDU Length
Exponent, Rx Antenna Pattern Consistency, and Tx Antenna Pattern
Consistency of 6 GHz capability through config file.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
For EU, where preCAC is allowed, we should allow switch to DFS available
channels, instead of restarting BSS.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
When new credentials are configured and hostapd is reconfigured using
SIGHUP (or RELOAD on the ctrl_iface), also update the WPS credentials.
Before these changes, when WPS is triggered the Registar always serves
the credentials that were configured when hostapd started.
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
This is in preparation of larger changes in hostapd_update_wps() to keep
the commits more readable.
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
Some time ago it was found some drivers are setting their hw/ucode RX
filters restrictively enough to prevent broadcast DPP Action frames from
being received at upper layers in the stack.
A set of patches was introduced to the kernel and
ath9k driver as well as wpa_supplicant, e.g.,
a39e9af90 ("nl80211: DPP listen mode callback")
4d2ec436e ("DPP: Add driver operation for enabling/disabling listen mode")
However, the hostapd code itself was not calling the new multicast
registration. As such the AP side of things wasn't working as expected
in some scenarios. I've found this while trying to get ath9k working as
an AP Responder/Configurator.
The problem wasn't seen on, e.g., mac80211 hwsim driver.
Extend the wpa_supplicant mechanism to work with hostapd as well.
Signed-off-by: Michal Kazior <michal@plume.com>
In some contexts (e.g., Multi-AP) it can be useful to have access to
some of the management frames in upper layers (e.g., to be able to
process the content of association requests externally).
Add 'notify_mgmt_frames'. When enabled, it will notify the ctrl_iface
when a management frame arrives using the AP-MGMT-FRAME-RECEIVED event
message.
Note that to avoid completely flooding the ctrl_iface, not all
management frames are included (e.g., Beacon and Probe Request frames
are excluded).
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
When the AP advertised RSNE, RSNXE, and WPA IE, hostapd incorrectly
removed the RSNE in the EAPOL-Key msg 3/4 if the STA associates with
WPA, leaving only RSNXE instead of WPA IE. WPA STA fails to connect to
such AP as the WPA IE is missing.
Since RSNXE is not really used in non-RSN connection, just remove it
here with RSNE.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add HE as an accepted option ("he") in the CHAN_SWITCH command similarly
to the way VHT is addressed.
Signed-off-by: Muna Sinada <msinada@codeaurora.org>
Derive the KDK as part of PMK to PTK derivation if forced by
configuration or in case both the local AP and the peer station declare
support for secure LTF.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
IEEE P802.11az/D2.6 added definitions to include RSNXE in the PASN
negotiation. Implement the new functionality in both wpa_supplicant and
hostapd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
IEEE P802.11az/D2.6 defines the following additional capabilities to
RSNXE:
- Secure LTF support
- Secure RTT support
- Protection of range negotiation and measurement management frames.
Add support for advertising the new capabilities.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Note that the implementation is not complete as it is missing support
for the FT wrapped data which is optional for the station, but must be
supported by the AP in case the station included it.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
As the PASN FILS authentication is only defined for FILS SK without PFS,
and to support PASN authentication with FILS, implement the PASN with
FILS processing as part of the PASN handling and not as part of the WPA
Authenticator state machine.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Extend the fils_pmk_to_ptk() to also derive Key Derivation
Key (KDK) which can later be used for secure LTF measurements.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Extend the wpa_pmk_r1_to_ptk() to also derive Key Derivation
Key (KDK), which can later be used for secure LTF measurements.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Extend the wpa_pmk_to_ptk() to also derive Key Derivation
Key (KDK), which can later be used for secure LTF measurements.
Update the wpa_supplicant and hostapd configuration and the
corresponding WPA and WPA Auth state machine, to allow enabling of KDK
derivation. For now, use a testing parameter to control whether KDK is
derived.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add support for new channels 173 and 177 in the operating classes 125 to
130 as defined in draft IEEE P802.11ax/D8.0.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
After sending DPP Auth Response, the Responder might not receive the
Auth Confirm either due to the Initiator not sending it or the reception
of the frame failing for some reason (e.g., Responder having already
left the negotiation channel). If this happens, following initiation
attempts would fail since the consecutive Auth Request would get
discarded since the previous authentication is still in progress.
Terminate DPP authentication on Responder, if no Auth Confirm is
received within one second of successfully sending Auth Response. This
allows the Responder to accept start of a new exchange.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Support possible band combinations of 2.4 GHz, 5 GHz, and 6 GHz with
QCA_WLAN_VENDOR_ATTR_SETBAND_MASK attribute. Ensure backwards
compatibility with old drivers that are using
QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE attribute and supporting only 2.4 GHz
and 5 GHz bands.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Add a new hostapd configuration parameters rssi_ignore_probe_request to
ignore Probe Request frames received with too low RSSI.
Signed-off-by: John Crispin <john@phrozen.org>
Previously hostapd would not stop transmitting when a DFS event was
detected and no available channel to switch to was available.
Disable and re-enable the interface to enter DFS state. This way, TX
does not happen until the kernel notifies hostapd about the NOP
expiring.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add the ability to disable HT/VHT/HE for specific BSS from hostapd.conf.
- Add disable_11ax boolean to hostapd_bss_config.
- Change disable_11n and disable_11ac to bool in hostapd_bss_config.
- Add configuration option to set these disable_11* parameters
(which were previously used only automatically based on incompatible
security parameters to disable HT/VHT).
Signed-off-by: Shay Bar <shay.bar@celeno.com>
The hostapd DFS code deinitializes and initializes the AP interface, if
a clean channel switch is not possible. In this case the AP code paths
would deinit the driver, for example nl80211, without wpa_supplicant
code paths getting notice of this.
Therefore add callbacks for wpa_supplicant mesh methods, which are
called on init/deinit of the AP BSS. These callbacks are then used to
handle the reset in the mesh code.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Mesh join function is the last function to be called during mesh join
process, but it's been called a bit earlier than it's supposed to be, so
that some mesh parameter values such as VHT capabilities were not
applied correct when mesh join is in process. Moreover, the current
design of mesh join that is called directly after mesh initialization
isn't suitable for DFS channels to use, since mesh join process should
be paused until DFS CAC is done and resumed after it's done.
The callback will be called by hostapd_setup_interface_complete_sync().
There is a possibility that completing mesh init fails, so add error
handling codes for that.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
Use NL80211_ATTR_SAE_PWE attribute to indicate the sae_pwe value
to the driver during the NL80211_CMD_START_AP and NL80211_CMD_CONNECT
in WPA3-Personal networks which are using SAE authentication.
Signed-off-by: Rohan Dutta <drohan@codeaurora.org>
The newer kernel versions enforce strict netlink attribute policy
validation and will cause cfg80211 to reject vendor commands with
NL80211_ATTR_VENDOR_DATA if NLA_F_NESTED attribute is not set but
if the vendor command is expecting nested data within
NL80211_ATTR_VENDOR_DATA attribute.
Most of the earlier instances were addressed by adding NLA_F_NESTED
flag in nla_nest_start(). This commit addresses the remaining
instance in which NL80211_ATTR_VENDOR_DATA is populated using data
set by user through the control interface.
Enhance the control interface VENDOR command to indicate whether the
vendor subcommand uses nested attributes within NL80211_ATTR_VENDOR_DATA
attribute or not.
Set NLA_F_NESTED flag for existing QCA vendor commands which use nested
attributes within the NL80211_ATTR_VENDOR_DATA attributes so that the
old frameworks implementations for already existing commands work
without any issues.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When SAE is used, the local pointer pmk may point to sm->PMK. Skip the
memcpy operation in such a case since it is not really needed and use of
overlapping memory buffers is undefined behavior for memcpy().
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Make sae_status_success() more explicit by rejecting SAE-PK status code
when the AP is not configured with PK.
Fixes: 20ccf97b3d ("SAE-PK: AP functionality")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is needed to cover the HE-specific conf->he_oper_chwidth value in
addition to conf->vht_oper_chwidth.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Some places in the code base were not using the wrappers like
hostapd_set_oper_centr_freq_seg0_idx and friends. This could lead to
errors, for example when joining 80 MHz mesh networks. Fix this, by
enforcing usage of these wrappers.
wpa_supplicant_conf_ap_ht() now checks for HE capability before dealing
with VHT in order for these wrappers to work, as they first check HE
support in the config.
While doing these changes, I've noticed that the extra channel setup
code for mesh networks in wpa_supplicant/mesh.c should not be necessary
anymore and dropped it. wpa_supplicant_conf_ap_ht() should handle this
setup already.
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
We don't really need to duplicate more of this, so just
move the lib.rules include to the end and do more of the
stuff that's common anyway there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Derive the library name from the directory name, and let each
library Makefile only declare the objects that are needed.
This reduces duplicate code for the ar call. While at it, also
pretty-print that call.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is something I hadn't previously done, but there are
cases where it's needed, e.g., building 'wlantest' and then
one of the tests/fuzzing/*/ projects, they use a different
configuration (fuzzing vs. not fuzzing).
Perhaps more importantly, this gets rid of the last thing
that was dumped into the source directories, apart from
the binaries themselves.
Note that due to the use of thin archives, this required
building with absolute paths.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of building in the source tree, put most object
files into the build/ folder at the root, and put each
thing that's being built into a separate folder.
This then allows us to build hostapd and wpa_supplicant
(or other combinations) without "make clean" inbetween.
For the tests keep the objects in place for now (and to
do that, add the build rule) so that we don't have to
rewrite all of that with $(call BUILDOBJS,...) which is
just noise there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When testing SAE reflection, the incoming commit may have the H2E status
code (126) or SAE-PK (127), but the test code in the AP was always
sending back status code 0. The STA would then reject the commit
response due to expecting H2E/SAE-PK status code.
Just reflect the incoming status code so the commit can be rejected
based on the SAE contents regardless of which variant of SAE was used.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Some legacy stations copy previously reserved RSN capability bits,
including OCVC, in (Re)Association Request frames from the AP's RSNE but
do not indicate MFP capability and/or do not send OCI in RSN handshakes.
This is causing connection failures with such erroneous STAs.
To improve interoperability with such legacy STAs allow a workaround OCV
mode to be enabled to ignore OCVC=1 from the STA if it does not follow
OCV requirements in the first protected exchange. This covers cases
where a STA claims to have OCV capability, but it does not negotiate use
of management frame protection or does not include OCI in EAPOL Key msg
2/4, FT Reassociation Request frame, or FILS (Re)Association Reqest.
The previous behavior with ocv=1 is maintained, i.e., misbehaving STAs
are not allowed to connect. When the new workaround mode is enabled with
ocv=2, the AP considers STA as OCV capable on below criteria
- STA indicates both OCV and MFP capability
- STA sends OCI during connection attempt in a protected frame
Enabling this workaround mode reduced OCV protection to some extend
since it allows misbehavior to go through. As such, this should be
enabled only if interoperability with misbehaving STAs is needed.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Modify status code in FT Reassociation Response frame from
WLAN_STATUS_UNSPECIFIED_FAILURE to WLAN_STATUS_INVALID_FTE when replying
to an invalid OCI channel info (subelement of FTE) in FT Reassociation
Request frame.
Signed-off-by: Shaakir Mohamed <smohamed@codeaurora.org>
Generate a control interface event upon receipt of DPP Presence
Announcement frames. This allows external programs to instrument hostapd
with bootstrapping information on-demand.
Signed-off-by: Andrew Beltrano <anbeltra@microsoft.com>
When a Presence Announcement frame is received, a check is done to
ensure an ongoing auth is not in progress (!hapd->dpp_auth). A new DPP
auth is then initialized, however, when setting global configurator
params for it, the hapd->dpp_auth pointer is used which was earlier
confirmed as NULL, causing a crash in dpp_set_configurator params when
the pointer is dereferenced.
This only occurs when there are global DPP configurator params to be set
and the peer has no overriding configurator params. If no global DPP
configurator params exist, the call to dpp_set_configurator exits early
and the problem is not observed.
Fix by using the newly init'ed DPP auth structure for setting global
DPP configurator params.
Signed-off-by: Andrew Beltrano <anbeltra@microsoft.com>
The Query Response Length field was missing from GAS Initial Response
and GAS Comeback Response frames in the DPP specific code path from
hostaps GAS server. This resulted in invalid frames being used when the
DPP Config Response needed fragmentation. Fix this by adding the Query
Response Length fields into these frames.
Signed-off-by: Disha Das <dishad@codeaurora.org>
Initiate SA Query for a WPS+MFP AP. STA flag checks for MFP added for
Association Request frames that use WPS IE without RSNE. This is needed
to avoid giving an opportunity to skip the protection against
disconnections when WPS is enabled.
Signed-off-by: Disha Das <dishad@codeaurora.org>
Resolved the below warning
../src/ap/ieee802_11.c:4535:25: warning: 'reply_res' may be used
uninitialized in this function [-Wmaybe-uninitialized]
if (sta && ((reply_res != WLAN_STATUS_SUCCESS &&
^
Since reply_res is been assigned inside an if condition and so
compiler treats reply_res as uninitalized variable
Initialize reply_res with WLAN_STATUS_UNSPECIFIED_FAILURE.
Fixes: 5344af7d22 ("FT: Discard ReassocReq with mismatching RSNXE Used value")
Signed-off-by: Karthikeyan Kathirvel <kathirve@codeaurora.org>
The AP mode condition for initiating the SA Query procedure when
receiving a new (Re)Association Request frame used only association
state and MFP negotiation result without checking that the key exchange
has been completed. This can give rise to a corner case where the SA
Query procedure may get started after open association but before the
4-way handshake has been completed, resulting in open SA query frames
over the air.
Fix this by adding station authorized check in hostapd_notif_assoc() and
check_assoc_ies().
Signed-off-by: Rohan <drohan@codeaurora.org>
Add support to skip sae_pk password check under compile flag
CONFIG_TESTING_OPTIONS which allows AP to be configured with
sae_pk enabled but a password that is invalid for sae_pk.
Signed-off-by: Shaakir Mohamed <smohamed@codeaurora.org>
Skip check to mandate MFP capability for OCV enabled STA when OCV is
disabled in AP. This is to improve interoperability with STAs in which
OCV capability is advertised incorrectly without advertising MFP when
OCV is disabled in AP.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Enhance the return values of ocv_verify_tx_params with enum to indicate
different OCI verification failures to caller.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Extend DPP authentication session search for the DPP_QR_CODE command to
cover the ongoing exchanges in Controller/Responder. This was previously
done for wpa_supplicant, but not for hostapd, so complete this support
on the hostapd side.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Extend hostapd support for DPP Controller to cover the DPP_CONTROLLER_*
cases that were previously implemented only in wpa_supplicant. This
allows hostapd/AP to be provisioned using DPP over TCP.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
As per RFC 8110 (Opportunistic Wireless Encryption), if the AP has the
PMK identified by the PMKID and wishes to perform PMK caching, it will
include the PMKID in the Association Response frame RSNE but does not
include the Diffie-Hellman Parameter element.
This was already addressed for most cases with owe_process_assoc_req()
not setting sta->owe_ecdh in case PMKSA caching is used. However, it was
possible to an old STA entry to maintain the initial sta->owe_ecdh value
if reassociation back to the same AP was used to initiate the PMKSA
caching attempt. Cover that case by adding an explicit check for the
time when the Association Response frame is being generated.
Signed-off-by: Chittur Subramanian Raman <craman@maxlinear.com>
The function hostapd_event_ch_switch() derived the seg0_idx and seg1_idx
values only for the 5 GHz and 2.4 GHz bands and the 6 GHz case ended up
using incorrect calculation based on the 5 GHz channel definitions.
Fix this by adding support for 6 GHz frequencies.
Signed-off-by: Rohan <drohan@codeaurora.org>
Add an encrypted Enrollee identifier into Reconfig Announcement frames
and decrypt that on the Configurator side. The actual E-id value is
currently not used for anything, but it can be used in the future to
provide better control over reconfiguration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This was added to the protocol design to support cases where the
C-sign-key uses a different group than the netAccessKey. The Enrollee
now indicates its netAccessKey group in Reconfig Announcement and the
Configurator builds it own reconfig Connector using that group instead
of the group used for the C-sign-key.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This prevents use of a SAE-PK style password as the WPA-PSK passphrase
only if the same password is not also enabled through sae_password for
use with SAE-PK.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
