Add support for overriding EHT Operation element puncturing mask
for testing purposes.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
STA EHT MCS and NSS set field size shouldn't depend on AP HE operation
channel width. Fix it.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reorder the Element ID List to fill in the values in increasing order to
match the way the Element ID List is defined.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Currently while deciding to create a new Multiple BSSID element based on
the condition when the length reaches 255, the length value being used
is the total element length (including the length of the Element ID and
Length fields as well). However, the value in the length field denotes
the number of octets following it and excluding itself. Hence including
the total length is wrong. This leads to incorrect count of Multiple
BSSID elements.
And while filling the data, the length is considered porperly as it
should be hence we are filling more data in a single go and all data is
filled in MBSSID count which is less than originally calculated. This
ultimately leads to incorrect length calculation during nla_put() and
setting the beacon to the driver fails while putting the Multiple BSSID
element data into the netlink socket buffer.
Fix this issue by considering the length excluding the Element ID and
Length field sizes.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Share VLAN info in RRB when the driver advertises support for VLAN
offload (WPA_DRIVER_FLAGS_VLAN_OFFLOAD). sta->vlan_desc is unused in
this case, only sta->vlan_id is used. Skip the checks that are based on
sta->vlan_desc.
Signed-off-by: Sai Pratyusha Magam <quic_smagam@quicinc.com>
Instead of rejecting the Multi-Link element, skip unknown subelements to
be less likely to cause interop issues for future. IEEE P802.11be/D5.0
allows other optional subelements to be included here.
Signed-off-by: Jouni Malinen <j@w1.fi>
This function is both updating the hostapd-internal sta->flags value and
sending out the AP-STA-CONNECTED control interface message. When
authorizing a STA, the call to this function is followed by a driver
command to update the flags of the STA entry in the driver. That has a
race condition at least for UML time-travel since the AP-STA-CONNECTED
event is used as a message to wait for before running a connectivity
test or some other operation that depends on the data connection being
in working condition.
Split the function into two steps so that the driver STA entry update
can be done between those two steps for the cases where it matters for
the race condition. In other words, send the AP-STA-CONNECTED message
only after having authorized the STA in the driver.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify that sta is not NULL before calling
hostapd_process_assoc_ml_info() that references this parameter. In
theory, sta might be NULL here if addition of the STA entry failed in
the 60 GHz case.
Signed-off-by: Jouni Malinen <j@w1.fi>
This line seemed to trigger SIGSEGV in some code coverage testing cases.
It is not exactly clear how that was possible, but just in case, check
that iface->current_mode is set before using it here.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the BSS TM Request for imminent BSS temoval is for a non-AP MLD that
has multiple affiliated links, do not schedule full disconnection since
other links remain associated.
Signed-off-by: Jouni Malinen <j@w1.fi>
Allow link removal imminent indication to be added with the new
link_removal_imminent=1 parameter to BSS_TM_REQ.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When the AP MLD sends an Action frame to a non-AP MLD, use the AP MLD
MAC address instead of the local AP address (BSSID).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When the AP is configured to operate as an AP MLD, use the AP MLD MAC
address when needed for transmission of WNM Action frames.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Remove a spurious \tab char in hostapd_eid_rnr() between arguments to a
function.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
In case the TBTT information is reporting about an AP in the same AP MLD
as the current AP, the AP MLD ID in the MLD Parameters subfield should
be set to 0.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Link ID needs to be specified for MLD case when doing channel switch.
Add it to the driver command.
Signed-off-by: Chenming Huang <quic_chenhuan@quicinc.com>
There are different CHAN_SWITCH flows for DFS and non-DFS channels.
Non-DFS one saves previous BW value in iface->conf, but DFS flow
replaces it with a new user requested value. Setting a non-DFS channel
after a DFS one with BW = 160 would have resulted in a mismatch between
the saved BW and vht_capab (if VHT160 was not included by default). This
would have led to a check fail in the hostapd_set_freq_params()
function.
Signed-off-by: Dmitrijs Martinovs <dmartinovs@maxlinear.com>
All the station flags other than WPA_STA_SHORT_PREAMBLE are relevant
only for the MLD station and not to the link stations (as these flags
are related to the MLD state and not the link state).
As for the WPA_STA_SHORT_PREAMBLE, since the station is an EHT
station, it must have short preamble.
Thus, do not propagate the flags change for link stations to the driver.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add additional check for 6 GHz operating class. Otherwise this results
in setting incorrect segment 0 index for 5 GHz 40 MHz channel 157-161,
which has the same center segment 0 index 159 as 6 GHz 320 MHz expected
channel.
Fixes: 085a3fc76e ("EHT: Add 320 channel width support")
Signed-off-by: Mikelis Vuls <mvuls@maxlinear.com>
Removing radio measurements and supported operating class indication
might be needed to reduce binary size for a memory constrained system
that does not need more advanced features. However, removing these is
not recommended since they can help the AP manage the network and STA
steering.
By default this functionality is enabled.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
The length of the PMK ended up getting lost when a PMKSA cache entry was
added based on externally managed information. Set the PMK length in SAE
context to get the correct length stored into the actual PMKSA cache
entry that gets created in this path.
Signed-off-by: Jouni Malinen <j@w1.fi>
USe the link ID information to determine the specific affiliated link
when processing channel switch events on an AP MLD.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Do include group MLO KDEs for links for which the information is
missing.
In addition, set the KDE buffer length based on the added data.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When processing a (Re)Association Request frame and no corresponding
station is found, try to find the station using the station MLD MAC
address from the Basic ML element, as it is possible that the station
is trying to re-associate but with a different link address (in such
a case the underlying driver would not perform address translations).
When sending the (Re)Association Response frame, use the addresses from
the (Re)Association Request frame and not the AP MLD MAC address, again,
to avoid the address translation done in the driver.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
IEEE P802.11be/D4.0, 9.4.2.312.2.3 states that the AP MLD ID should only
be included in some ML probe responses. Beacon frames shouldn't include
AP MLD ID.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This responds by simply embedding most of the IEs from the other links
into the ML element. This is not correct really, as inheritance rules
should be applied and an inheritance element may need to be added.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add a simple for_each_mld_link helper that sets first variable to the
hapd data for every link. It takes the interfaces and MLD ID as
arguments and two extra integers as scratch variables (for the interface
and bss offsets).
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
This adds the parsing of ML probe requests. Handling will be added by a
later commit.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
To support ML probe request we will need to include IEs from the other
hapd instances in the response. Split the function to allow just
generating the per-instance IEs separately.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This effectively moves setting the csa/ecsa/cca position to happen
only when a Probe Response template for offloading is generated.
One could probably avoid the global variable altogether, as the
value is immediately consumed into struct {csa,cca}_settings.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
When the TX link rejects the association, return a status code for all
requested links. For simplicity, just return "TX link not accepted" so
that clients may try to connect to other links. This could be improved
to explicitly reject each link if directly associating to the link will
not work either.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add support for testing ML link removal to hostapd. While such support
should inherently be integrated with the underlining driver, simulate
the inclusion of the ML reconfiguration element in hostapd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Three functions were provided for defragmentation. First
ieee802_11_defrag(), ieee802_11_defrag_mle() and then
ieee802_11_defrag_data() which would do the actual job. With
ieee802_11_defrag() picking the member in the elements struct for an
EID. The problem with this is, that for the Multi-Link element, there
are multiple entries in the elems struct depending on its type. As such,
remove the intermediate function and simply pass the correct members
directly.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Enable support for ACS in the IEEE 802.11be/320 MHz case. To do so we
just:
- add channel definitions for the 320 MHz blocks of the 6 GHz band
- handle CONF_OPER_CHWIDTH_320MHZ in the different cases
- restrict 320 MHz to ieee80211be=1 only
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
Fix for the HE Channel Center Freq Seg0/Seg1 within the HE 6GHz
Operation Information field. As downgrade of bandwidths for VHT and HE
when using puncturing is TODO for 320 MHz and/or if puncturing is
disabled and bandwidth is 320 MHz, the same rules as for 160 MHz should
be applied for Channel Center Freq Seg0/Seg1 within 6 GHz Operation
Information field.
Signed-off-by: Jurijs Soloveckis <jsoloveckis@maxlinear.com>
Include EHT Operation Information field only if the operating bandwidth
is 320 MHz or there is at least one punctured 20 MHz subchannel. This
behavior is defined in IEEE P802.11be/D4.0, 35.15.1 (Basic EHT BSS
operation).
Signed-off-by: Jurijs Soloveckis <jsoloveckis@maxlinear.com>
MBSSID shares a single Beacon frame with multiple BSSs. This implies
that the key used for beacon protection (BIGTK) needs to be shared. The
nontransmitted BSSs managed their own BIGTK previously and that resulted
in providing incorrect value to the stations associated with those BSSs.
Use the BIGTK from the transmitted BSS to fix this.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Fix references to the appropriate driver capability drv_flags2. The
initial version used the incorrect drv_flags value and by doing so,
ended up using incorrect driver capabilities (DEAUTH_TX_STATUS,
BSS_SELECT, TDLS_SUPPORT) which could result in incorrect OWE
functionality for both AP and STA cases.
Fixes: d984c7b298 ("hostapd: Add support for OWE offload for STA/AP interface")
Fixes: da364180fb ("hostapd: Support 4-way handshake offload for AP/P2P GO")
Signed-off-by: Vinayak Yadawad <vinayak.yadawad@broadcom.com>
