Commit graph

1960 commits

Author SHA1 Message Date
Sathishkumar Muruganandam
bda9c08596 hostapd: Fix CHAN_SWITCH command for VHT20 and VHT40
Previously, hostapd CHAN_SWITCH command did not effect VHT configuration
for the following:

When VHT is currently disabled (ieee80211ac=0),

1. hostapd_cli -p /var/run/hostapd chan_switch 10 5180 \
                sec_channel_offset=1 center_freq1=5190 bandwidth=40 ht

====> Comes up in HT40

2. hostapd_cli -p /var/run/hostapd chan_switch 10 5765 \
                sec_channel_offset=-1 center_freq1=5775 bandwidth=40 vht

====> Comes up in HT40

3. hostapd_cli -p /var/run/hostapd chan_switch 10 5200 center_freq1=5200 \
                                                  bandwidth=20 vht

====> Comes up in HT20

When VHT is currently enabled (ieee80211ac=1),

1. hostapd_cli -p /var/run/hostapd chan_switch 10 5180 \
                sec_channel_offset=1 center_freq1=5190 bandwidth=40 ht

====> Comes up in VHT40

2. hostapd_cli -p /var/run/hostapd chan_switch 10 5200 center_freq1=5200 \
                                                  bandwidth=20 ht

====> Comes up in VHT20

This is since VHT config from chan_switch is processed only for
bandwidths 80 and above (80P80, 160) and for VHT20, VHT40 cases, only
NLA chan type and chan width are updated.

There is no NL attribute for determining if it is HT or VHT for
bandwidths 20 & 40 and currently they are updated as HT20, HT40 (+ or -
depending on offset). Same is notified back via
NL80211_CMD_CH_SWITCH_NOTIFY.

Instead of adding new NL attribute for tracking HT/VHT enabled config,
we are adding new hostapd VHT config parameter to save the chan_switch
config and use only for chan_switch case of VHT20 and VHT40.

Tested with all combinations of chan_switch (noHT->20->40->80->) HT/VHT
and confirmed to be working.

Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
2018-05-16 01:16:54 +03:00
Karthikeyan Periyasamy
c4dd3afa3c ACS: Avoid invalid interference factor when survey channel time is zero
When the channel time is zero the interference factor calculation falls
under divide by zero operation which results in invalid (NaN =
not-a-number) interference factor value. This leads to wrong ideal
channel selection in ACS during the scenario described below.

Scenario:

In VHT80 mode, the channel 36 (first channel) gets the channel time as
zero which causes the interfactor factor to be an invalid number (NaN).
Any operations (like addition, mulitplication, divide, etc.) with NaN
value results in a NaN value, so that average factor for the primary
channel 36 got the invalid value (NaN). Since channel 36 is the first
channel, ideal factor is assigned as NaN in the first iteration. The
following iteration condition check (factor < ideal_factor) with a NaN
value fail for all other primary channels. This results in channel 36
being chosen as the ideal channel in ACS which holds a NaN value.

Logs:

ACS: Survey analysis for channel 36 (5180 MHz)
ACS: 1: min_nf=-103 interference_factor=nan nf=0 time=0 busy=0 rx=0
ACS: 2: min_nf=-103 interference_factor=0.615385 nf=-102 time=13 busy=8 rx=0
ACS: 3: min_nf=-103 interference_factor=2.45455 nf=0 time=22 busy=16 rx=0
ACS: 4: min_nf=-103 interference_factor=0.785714 nf=-103 time=42 busy=33 rx=0
ACS: 5: min_nf=-103 interference_factor=nan nf=0 time=0 busy=0 rx=0
ACS:  * interference factor average: nan
...
ACS:  * channel 36: total interference = nan
..
ACS:  * channel 149: total interference = 5.93174e-21
..
ACS: Ideal channel is 36 (5180 MHz) with total interference factor of nan

Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
2018-05-16 01:16:54 +03:00
Jouni Malinen
d501c27cfe EAP-TLS server: Disable TLS v1.3 by default
The current EAP peer implementation is not yet ready for the TLS v1.3
changes with EAP-TTLS, EAP-PEAP, and EAP-FAST, so disable TLS v1.3 for
this EAP method for now.

While the current EAP-TLS implementation is more or less complete for
TLS v1.3, there has been no interoperability testing with other
implementations, so disable for by default for now until there has been
chance to confirm that no significant interoperability issues show up
with TLS version update. tls_flags=[ENABLE-TLSv1.3] configuration
parameter can be used to enable TLS v1.3 (assuming the TLS library
supports it; e.g., when using OpenSSL 1.1.1).

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-05-01 22:13:38 +03:00
Jouni Malinen
4526038092 HS 2.0: Terms and Conditions testing feature in authentication server
Allow hostapd RADIUS authentication server with SQLite EAP user DB to be
used for testing Terms and Conditions functionality. This could be used
for the HO AAA part of functionality (merging HO AAA and SP AAA into a
single component to avoid separate RADIUS proxy in testing setup).

A T&C server with HTTPS processing is needed to allow this to be used
for full over-the-air testing. This commit adds sufficient functionality
to allow hwsim test cases to cover the RADIUS server part.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-04-26 17:56:22 +03:00
Jouni Malinen
f456940ef3 HS 2.0: CoA-Request processing for Terms and Conditions filtering
Extend RADIUS DAS to support CoA-Request packets for the case where the
HS 2.0 Terms And Conditions filtering VSA is used to remove filtering.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-04-25 12:57:46 +03:00
mazumdar
d239ab3962 DFS: Mark channels required DFS based on reg-domain info from the driver
Mark a channel as required DFS based on regulatory information received
from the driver/kernel rather than deciding based on hardcoded
boundaries on the frequency. Previously few channels were being marked
as requiring DFS even though they were non-DFS in a particular country.

If the driver does not provide channel list information, fall back to
the previously used frequency-based determination.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-04-24 00:35:47 +03:00
Jouni Malinen
8760b9848c HS 2.0: Send Terms and Conditions Acceptance notification
This extends hostapd Access-Accept processing to check if the RADIUS
server indicated that Terms and Conditions Acceptance is required. The
new hs20_t_c_server_url parameter is used to specify the server URL
template that the STA is requested to visit.

This commit does not enable any kind of filtering, i.e., only the part
of forwarding a request from Access-Accept to the STA using
WNM-Notification is covered.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-04-24 00:35:47 +03:00
Jouni Malinen
6cb8f4f382 HS 2.0: Terms and Conditions attributes in Access-Request messages
This extends hostapd with two new configuration parameters
(hs20_t_c_filename and hs20_t_c_timestamp) that can be used to specify
that the Terms and Conditions attributes are to be added into all
Access-Request messages for Hotspot 2.0 STAs.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-04-24 00:35:47 +03:00
Bhagavathi Perumal S
1952b626ba hostapd: Add ctrl iface indications for WDS STA interface
This allows user to get event indication when a new interface is
added/removed for 4addr WDS STA and also WDS STA ifname is informed
through the STA command.

Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
2018-04-24 00:35:47 +03:00
Tova Mussai
c4315e6620 AP: Handle AP initalization failure in async flow
When AP initialization is completed in a callback (e.g., OBSS scan),
wpa_supplicant_deinit_ap() is not called in case of failure. Fix this by
calling setup_complete_cb in case of failure, too, which in turn calls
wpa_supplicant_deinit_ap() if needed.

Signed-off-by: Tova Mussai <tova.mussai@intel.com>
2018-04-20 00:48:49 +03:00
Jouni Malinen
67cca34645 HS 2.0: Copy Roaming Consortium OI from (Re)AssocReq to Access-Request
This extends hostapd processing of (Re)Association Request frames to
store a local copy of the Consortium OI within the Roaming Consortium
Selection element, if present, and then add that in HS 2.0 Roaming
Consortium attribute into RADIUS Access-Request messages.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-04-17 16:40:47 +03:00
Jouni Malinen
0e450db285 HS 2.0: Allow configuration of operator icons
This extends hostapd Hotspot 2.0 implementation to allow operator icons
to be made available. The existing hs20_icon parameter is used to define
the icons and the new operator_icon parameter (zero or more entries) is
used to specify which of the available icons are operator icons. The
operator icons are advertised in the Operator Icon Metadata ANQP-element
while the icon data can be fetched using the same mechanism (icon
request/binary file) that was added for the OSU Providers icons.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-04-17 16:40:47 +03:00
Jouni Malinen
4d6eb9f2e2 Fix hostapd wmm_enabled setup on config reload path
If there is no explicit wmm_enabled parameter in the configuration
(i.e., conf->wmm_enabled == -1), the configuration reload path needs to
initialize conf->wmm_enabled based on iconf->ieee80211n in
hostapd_reload_bss() similarly to what is done in the initial startup
case in hostapd_setup_bss().

This fixes issues with RSN capabilities being set incorrectly when WMM
is supposed to get enabled and unexpectedly enabling WMM when it is not
supposed to be enabled (HT disabled). Either of these issues could show
up when asking hostapd to reload the configuration file (and when that
file does not set wmm_enabled explicitly).

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-04-06 23:29:11 +03:00
Michael Braun
a6509e850e FT: Add session_timeout to push/resp
This ensures a session timeout configured on R0KH either using
RADIUS-based ACL or 802.1X authentication is copied over to the new
R1KH.

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2018-04-06 19:57:53 +03:00
Michael Braun
3cb286ca49 FT: Add set/get session_timeout callback functions
These are needed to allow wpa_auth_ft.c to control session_timeout
values for STAs.

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2018-04-06 19:48:15 +03:00
Michael Braun
13f118dc59 Convert STA session_timeout to os_reltime
This is needed to allow the remaining session time to be computed for FT
(when sending PMK-R1 to another AP).

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2018-04-06 19:48:11 +03:00
Michael Braun
069b4e3048 FT: Include identity and radius_cui in pull/resp frames
This allows APs using FT to get the EAP session information from R0KH to
R1KHs.

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2018-04-06 19:09:16 +03:00
Michael Braun
9fbe292ff3 FT: Move wpa_ft_rrb_build_r0() special case to caller
Handle the special case of no PMK-R0 entry in the caller instead of
having to have wpa_ft_rrb_build_r0() aware of the possibility of pmk_r0
being NULL.

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2018-04-06 19:09:16 +03:00
Michael Braun
8c345234fd FT: Add set/get identity/radius_cui callback functions
These are needed to allow wpa_auth_ft.c to control identity/radius_cui
values for STAs.

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2018-04-06 19:01:16 +03:00
Michael Braun
17a8a9893f Fix potential memory leak with identity/radius_cui
ieee802_11_set_radius_info() might be called with a STA entry that has
already stored identity and/or radius_cui information, so make sure the
old values get freed before being replaced by the new ones.

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2018-04-06 19:01:16 +03:00
Michael Braun
17010c38d0 FT: Add IEEE VLAN support (including tagged VLANs)
This uses set_vlan()/get_vlan() callbacks to fetch and configure the
VLAN of STA. Transmission of VLAN information between APs uses new TLVs.

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2018-04-06 19:01:13 +03:00
Michael Braun
47a039b01b FT: Add set_vlan()/get_vlan() callback functions
These are needed to allow wpa_auth_ft.c to control VLAN assignment for
STAs.

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2018-04-05 22:39:21 +03:00
Michael Braun
3a3e28320b FT: Add expiration to PMK-R0 and PMK-R1 cache
IEEE Std 802.11-2016, 12.7.1.7.1 indicates that the lifetime of the
PMK-R0 (and PMK-R1) is bound to the lifetime of PSK or MSK from which
the key was derived. This is currently stored in r0_key_lifetime, but
cache entries are not actually removed.

This commit uses the r0_key_lifetime configuration parameter when
wpa_auth_derive_ptk_ft() is called. This may need to be extended to use
the MSK lifetime, if provided by an external authentication server, with
some future changes. For PSK, there is no such lifetime, but it also
matters less as FT-PSK can be achieved without inter-AP communication.

The expiration timeout is then passed from R0KH to R1KH. The R1KH verifies
that the given timeout for sanity, it may not exceed the locally configured
r1_max_key_lifetime.

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2018-04-05 13:58:20 +03:00
Michael Braun
09211c9894 FT: Use dl_list for PMK-R0/R1 cache
This makes it easier to remove expired entries from the list.

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2018-04-05 13:56:04 +03:00
Michael Braun
89dea17e13 FT: Add helper function for FILS key storing
FILS calls wpa_ft_store_pmk_r0() from wpa_auth.c. This is moved into a
new function wpa_ft_store_pmk_fils() in preparation of additional
information being needed.

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2018-04-05 13:47:43 +03:00
Michael Braun
83fe4bd3bf FT: Convert r0_key_lifetime to seconds
Add a new configuration option ft_r0_key_lifetime that deprecates
r0_key_lifetime. Though, the old configuration is still accepted for
backwards compatibility.

This simplifies testing. All other items are in seconds as well. In
addition, this makes dot11FTR0KeyLifetime comment match with what got
standardized in the end in IEEE Std 802.11r-2008.

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2018-04-05 13:47:23 +03:00
Ben Greear
c6b5b9a33b hostapd: Add more authentication error case debugging
This can help one understand better why stations are failing
to authenticate.

Signed-off-by: Ben Greear <greearb@candelatech.com>
2018-04-02 16:53:10 +03:00
Ben Greear
e2fc13d0ab hostapd: Add logging around Michael MIC related failures
This can help one understand better why stations are failing
to authentication/associate.

Signed-off-by: Ben Greear <greearb@candelatech.com>
2018-04-02 16:51:29 +03:00
Ben Greear
e7525a2954 hostapd: Add send_auth_reply() caller info in debug logging
This can help one understand better what happens during the
authentication exchange.

Signed-off-by: Ben Greear <greearb@candelatech.com>
2018-04-02 16:47:26 +03:00
Mathy Vanhoef
9f917339cc tests: Fix clearing of IGTK PN in handshake retransmit test functions
When locating the position of the IGTK PN in the key data, we also need
to skip the KDE header, in addition to the keyid field. This fixes
hostapd RESEND_M3 and RESEND_GROUP_M1 behavior when PMF is negotiated
for the association. Previously, the IGTK KDE ended up getting
practically hidden since zeroing of the PN ended up clearing the KDE OUI
and Type fields.

Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
2018-04-01 21:47:16 +03:00
Jouni Malinen
7e1d3ee963 Add hostapd.conf venue_url to set Venue URL ANQP-element
The new venue_url parameter can now be used to set the Venue URL ANQP
information instead of having to construct the data and use
anqp_elem=277:<hexdump> to set the raw value.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-03-26 16:10:47 +03:00
Jouni Malinen
2f37387812 FILS: Add more complete support for FT-FILS use cases
This extends the original IEEE Std 802.11ai-2016 functionality with the
changes added in REVmd to describe how additional keys are derived to
protect the FT protocol using keys derived through FILS authentication.

This allows key_mgmt=FT-FILS-SHA256 to be used with FT protocol since
the FTE MIC can now be calculated following the changes in REVmd. The
FT-FILS-SHA384 case is still unsupported (it needs support for variable
length MIC field in FTE).

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-03-26 12:31:04 +03:00
Jouni Malinen
4ddca8142e FT: Derive PMK-R1 locally if requested PMKR0Name is found
Derive PMK-R1 locally if the derived PMKR1Name is not found from the
local cache, but the request is for a key that was originally generated
locally (R0KH-ID matches) and the PMKR0Name is found in the local cache.
This was apparently not hit in the previously used FT sequences, but
this is useful to have available if a PMK-R1 entry is dropped from the
local cache before PMK-R0.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-03-24 18:53:14 +02:00
Jouni Malinen
1dc0945cc9 FT: Do not send PMK-R1 pull request to own R0KH address
If the requested key is not available locally, there is no point in
trying to send a pull request back to self for the key.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-03-24 18:53:14 +02:00
Jouni Malinen
9d94e4bb6b SAE: Fix PMKID in EAPOL-Key msg 1/4
Previously, the association that used SAE authentication ended up
recalculating the PMKID for EAPOL-Key msg 1/4 using incorrect
PMK-to-PMKID derivation instead of using the previously derived PMKID
from SAE. The correct PMKID was used only when going through PMKSA
caching exchange with a previously derived PMKSA from SAE.

Fix this by storing the SAE PMKID into the state machine entry for the
initial SAE authentication case when there is no explicit PMKSA entry
attached to the station.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-03-23 18:44:48 +02:00
Jouni Malinen
10949e2480 Do not disable 40 MHz based on co-ex report with matching primary channel
When processing 20/40 BSS Coexistence Management frames that do not
explicitly require 40 MHz to be disabled, check whether the reported
channels in 20/40 BSS Intolerant Channel Report element match the
current primary channel. If so, allow 40 MHz operation to continue. This
makes the during-operation updates for 20/40 Operation Permitted more
consistent with the scans during initial BSS startup.

The received 20/40 BSS Intolerant Channel Report channels are to be used
in the OT set in the during-operation determination and the P == OT_i
exception was ignored in the previous implementation which could result
in the AP first starting with 40 MHz and then dropping to 20 MHz on
first received 20/40 BSS Coexistence Management frame even though there
was no change in the neighboring BSSs.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-03-21 16:58:05 +02:00
Jouni Malinen
8cbd9c3ed4 Support multiple 20/40 BSS Intolerant Channel Report elements
This extends 20/40 BSS Coexistence Management frame processing to
iterate over all the included 20/40 BSS Intolerant Channel Report
elements instead of using only the first one.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-03-21 16:53:50 +02:00
Jouni Malinen
8127a0ac02 Ignore intra-BSS 20/40 BSS Coexistence Management from not-associated STA
The 20 MHz BSS Width Request field is set to 1 only for intra-BSS
reports. As such, ignore the frame if such a claim is made by a
transmitter that is not currently associated with the AP.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-03-21 16:35:15 +02:00
Jouni Malinen
8aa599d45a Add more debug prints for 20/40 BSS Coexistence Management frame Rx
This makes it easier to understand what kind of information a STA is
reporting about 20/40 MHz coexistence requirements.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-03-21 16:32:35 +02:00
Rajkumar Manoharan
d58c3bd8b7 hostapd: Ignore LOW_ACK event for co-operative steering clients
Ignore hostapd_event_sta_low_ack for a station which has agreed to
steering by checking the agreed_to_steer flag. This flag will be set
whenever a station accepts the BSS transition request from the AP.
Without this ignoring of the LOW_ACK event, the steering in-progress
might be affected due to disassociation. In this way AP will allow some
time (two seconds) for the station to move away and reset the flag after
the timeout.

Co-Developed-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
2018-03-19 20:16:32 +02:00
Tamizh chelvam
ec2b5173ce Make STA opmode change event available to upper layers
Add an event callback for EVENT_STATION_OPMODE_CHANGED to allow
user/application to get the notification whenever there is a change in a
station's HT/VHT op mode.

The new events:
STA-OPMODE-MAX-BW-CHANGED <addr> <20(no-HT)|20|40|80|80+80|160>
STA-OPMODE-SMPS-MODE-CHANGED <addr> <automatic|off|dynamic|static>
STA-OPMODE-N_SS-CHANGED <addr> <N_SS>

Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
2018-03-19 20:07:22 +02:00
Bhagavathi Perumal S
72123a84cb hostapd: Add last_ack_rssi into ctrl iface cmd STA
This allows external application to get last ACK signal strength of the
last transmitted frame if the driver makes this information
(NL80211_STA_INFO_ACK_SIGNAL) available.

Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
2018-03-19 19:23:26 +02:00
Ashok Ponnaiah
f5701cc66e OWE: Clean up pointer check in a testing code path
Check wpa_auth_write_assoc_resp_owe() return value to keep static
analyzers happier. The code path where this could happen is not really
reachable due to the separate hapd->conf->own_ie_override check and
wpa_auth_write_assoc_resp_owe() returning NULL only in an error case in
the override path. Furthermore, clean up the pointer return value to use
a proper pointer (NULL vs. 0).

Signed-off-by: Ashok Ponnaiah <aponnaia@codeaurora.org>
2018-03-19 19:08:34 +02:00
Purushottam Kushwaha
8179ae3a2a DPP: Support retrieving of configurator's private key
To retain configurator information across hostapd/wpa_supplicant
restart, private key need to be maintained to generate a valid pair of
authentication keys (connector, netaccess_key, csign) for new enrollees
in the network.

Add a DPP_CONFIGURATOR_GET_KEY control interface API through which the
private key of an existing configurator can be fetched.

Command format:
DPP_CONFIGURATOR_GET_KEY <configurator_id>

The output from this command can then be used with
"DPP_CONFIGURATOR_ADD key=<hexdump>" to create the same key again.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-03-16 20:55:32 +02:00
Jouni Malinen
4bc801ab42 SAE: Fix EAPOL-Key integrity and key-wrap algorithm selection
The SAE AKM 00-0F-AC:8 is supposed to use EAPOL-Key Key Descriptor
Version 0 (AKM-defined) with AES-128-CMAC and NIST AES Key Wrap.
However, the previous implementation ended up using Key Descriptor
Version 2 (HMAC-SHA-1-128 and NIST AES Key Wrap). Fix this by using the
appropriate Key Descriptor Version and integrity algorithm. Use helper
functions to keep the selection clearer and more consistent between
wpa_supplicant and hostapd uses.

Note: This change is not backwards compatible. Both the AP and station
side implementations will need to be updated at the same time to
maintain functionality.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-03-16 13:36:42 +02:00
Srinivas Dasari
d74963d411 DPP: Extend dpp_test 89 functionality to transmit side
This extends dpp_test functionality to allow DPP exchanges to be stopped
after authentication is completed on the Initiator, i.e., after sending
out the Authentication Confirm message. Previously, dpp_test=89 was used
only on the Responder side to stop after receiving the Authentication
Confirm message. The main use case for this extended functionality is to
be able to stop the protocol exchange on a device that acts as
authentication Initiator and Enrollee.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-03-13 01:03:37 +02:00
Purushottam Kushwaha
f8bfc9cbde Use correct WPA_ALG_* values to compare for enum wpa_alg
enum wpa_alg was being compared with WPA_CIPHER_* values. That does not
work here and strict compilers will report this as an error. Fix the
comparision to use proper WPA_ALG_* values. This fixes testing
capability for resetting IPN for BIP.

Fixes: 16579769ff ("Add testing functionality for resetting PN/IPN for configured keys")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-03-13 00:32:43 +02:00
Tamizh chelvam
92eb00aec2 Extend ACL check for Probe Request frames
Extend ACL check to deny Probe Request frames for the client which does
not pass ACL check. Skip this check for the case where RADIUS ACL is
used to avoid excessive load on the RADIUS authentication server due to
Probe Request frames. This patch add wpa_msg event for auth and assoc
rejection due to acl reject.

Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
2018-03-03 00:42:16 +02:00
Jeffin Mammen
c05f96a386 FILS: Check kde more consistently to avoid static analyzer warnings
For FILS, __wpa_send_eapol() is called only with the kde != NULL, but a
static analyzer might not understand that. Add an explicit check kde !=
NULL similarly to the other cases going through the kde parameter to
silence such bogus warnings.

Signed-off-by: Jeffin Mammen <jmammen@codeaurora.org>
2018-03-02 21:27:30 +02:00
Jouni Malinen
f5e0a3324b SAE: Fix potential infinite loop in mismatching PMK case on AP
Commit e61fea6b46 ('SAE: Fix PMKSA caching
behavior in AP mode') modified the PSK fetching loop to not override PMK
in case of SAE with PMKSA caching. However, that commit missed the error
path cases where there is need to break from the loop with exact
negative of the check in the beginning of the loop. This could result in
hitting an infinite loop in hostapd if a station derived a different PMK
value from otherwise successfully completed SAE authentication or if a
STA used a different PMK with a PMKSA caching attempt after a previously
completed successful authentication.

Fix this by adding the matching break condition on SAE AKM within the
loops.

Fixes: e61fea6b46 ("SAE: Fix PMKSA caching behavior in AP mode")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-03-02 21:27:18 +02:00
Ashok Ponnaiah
a22e235fd0 OWE: Add testing RSNE for OWE assoc response with driver SME/MLME
Allow RSNE to be overwritten for testing purposes also in the
driver-based SME/MLME case.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-02-12 21:31:04 +02:00
Jouni Malinen
659ac96d7f ieee802_11_mgmt: Handle frame info more consistently
Check for the fi parameter to be non-NULL before trying to fetch the
ssi_signal information similarly to how the fi->freq was already
handled. While the meta information is supposed to be available, it
looks like there is at least one corner case where fi == NULL could be
used (Authentication frame reprocessing after RADIUS-based ACL).

Signed-off-by: Jouni Malinen <j@w1.fi>
2018-02-07 12:34:41 +02:00
Ashok Ponnaiah
458d8984de SAE: Reject request with mismatching PMKID (no PMKSA cache entry)
Reject SAE association request when PMKID is included in the RSNE, but
the corresponding PMKSA is not available in the AP.

Signed-off-by: Ashok Ponnaiah <aponnaia@codeaurora.org>
2018-02-07 12:24:36 +02:00
Ashok Ponnaiah
79ce2d519b OWE: Rename function to match use (driver-SME/MLME)
This function is used to process a (Re)Association Request frame, so
rename it appropriately to mention assoc_req instead of auth_req.

Signed-off-by: Ashok Ponnaiah <aponnaia@codeaurora.org>
2018-02-06 20:27:41 +02:00
Ashok Ponnaiah
759da93a89 OWE: Check for ECDH availability before use (driver-SME/MLME)
Verify that the STA has ECDH data available before trying to use this
data to add the OWE DH Params element.

Signed-off-by: Ashok Ponnaiah <aponnaia@codeaurora.org>
2018-02-06 20:25:41 +02:00
Ashok Ponnaiah
af65ef28f4 OWE: Add RSNE when not using PMKSA caching (driver-SME/MLME)
RSNE needs to be added both with and without use of PMKSA caching.

Signed-off-by: Ashok Ponnaiah <aponnaia@codeaurora.org>
2018-02-06 20:22:53 +02:00
Ashok Ponnaiah
5850cba384 OWE: Support DH groups 20 and 21 with driver-SME/MLME
This was already the case with the hostapd-based SME/MLME
implementation, but the OWE DH Param element construction for the
driver-based SME/MLME needed a matching change to set the group
properly.

Signed-off-by: Ashok Ponnaiah <aponnaia@codeaurora.org>
2018-02-06 20:20:22 +02:00
Michal Kazior
f9854c183d hostapd: Fix wpa_psk_file support for FT-PSK
For FT-PSK sm->xxkey was populated with only the first password on the
linked list (i.e., last matching password in the wpa_psk_file) in
INITPSK. This caused only that password to be recognized and accepted.
All other passwords were not verified properly and subsequently
prevented clients from connecting.

Hostapd would report:

 Jan 30 12:55:44 hostapd: ap0: STA xx:xx:xx:xx:xx:xx WPA: sending 1/4 msg of 4-Way Handshake
 Jan 30 12:55:44 hostapd: ap0: STA xx:xx:xx:xx:xx:xx WPA: received EAPOL-Key frame (2/4 Pairwise)
 Jan 30 12:55:44 hostapd: ap0: STA xx:xx:xx:xx:xx:xx WPA: invalid MIC in msg 2/4 of 4-Way Handshake
 Jan 30 12:55:45 hostapd: ap0: STA xx:xx:xx:xx:xx:xx WPA: EAPOL-Key timeout

Signed-off-by: Michal Kazior <michal@plumewifi.com>
2018-02-04 12:39:23 +02:00
David Messer
82424732af Fix compiler issue with CONFIG_TESTING_OPTIONS
Use the preprocessor conditional "ifdef" instead of "if" before
CONFIG_TESTING_OPTIONS to prevent an issue on build systems that treat
undefined preprocessor identifiers as an error.

Signed-off-by: David Messer <david.messer@garmin.com>
2018-02-03 12:41:09 +02:00
Ashok Ponnaiah
cd483be252 OWE: Use PMKSA caching if available with driver AP MLME
If a matching PMKSA cache entry is present for an OWE client, use it and
do not go through DH while processing Association Rquest frame.
Association Response frame will identify the PMKID in such a case and DH
parameters won't be present.

Signed-off-by: Ashok Ponnaiah <aponnaia@codeaurora.org>
2018-02-01 23:58:46 +02:00
Ashok Ponnaiah
a4668c6812 OWE: Handle unsupported finite cyclic group with driver MLME
Handle OWE unsupported finite cyclic group in (Re)Association Request
frame when not using the hostapd SME/MLME.

Signed-off-by: Ashok Ponnaiah <aponnaia@codeaurora.org>
2018-02-01 23:51:19 +02:00
Ashok Ponnaiah
18e3e9c6e0 OWE: Transition mode with non-AP-MLME
Add OWE Transition IE in build_ap_extra() ies to support drivers that do
not use hostapd MLME.

Signed-off-by: Ashok Ponnaiah <aponnaia@codeaurora.org>
2018-01-29 19:01:43 +02:00
Ashok Ponnaiah
92b6e0c582 hostapd: Send broadcast Public Action frame with wildcard BSSID address
Send Public Action frames with wildcard BSSID when destination was
broadcast address. This is required for DPP PKEX where the recipients
may drop the frames received with different BSSID than the wildcard
address or the current BSSID.

Signed-off-by: Ashok Ponnaiah <aponnaia@codeaurora.org>
2018-01-29 18:11:03 +02:00
Jouni Malinen
703470bfa1 FILS: Fix extended capability bit setting for FILS in AP mode
FILS capability bit setting could have ended up setting boths biths 72
(correct) and 64 (incorrect; part of Max Number of MSDUs In A-MSDU). Fix
this by adding the missing break to the switch statement.

Fixed: f55acd909e ("FILS: Set FILS Capability bit in management frames from AP")
Signed-off-by: Jouni Malinen <j@w1.fi>
2018-01-22 00:07:44 +02:00
Jouni Malinen
b6b5e3554a DPP: Get rid of compiler warnings on signed/unsigned comparison
Signed-off-by: Jouni Malinen <j@w1.fi>
2018-01-21 11:24:33 +02:00
Jouni Malinen
5d5ee699a5 Copy WLAN-Reason-Code value from Access-Reject to Deauthentication
This makes hostapd use the WLAN-Reason-Code value from Access-Reject
when disconnecting a station due to IEEE 802.1X authentication failure.
If the RADIUS server does not include this attribute, the default value
23 (IEEE 802.1X authentication failed) is used. That value was the
previously hardcoded reason code.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-01-12 20:55:33 +02:00
Jouni Malinen
feba5848be Replace RSNE group key management mismatch status/reason codes
Use "cipher out of policy" value instead of invalid group cipher (which
is for the group data frame cipher) and management frame policy
violation (which is used for MFPC/MFPR mismatch).

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-01-12 01:12:00 +02:00
Jouni Malinen
fd92095491 DPP: Report reception of Config Request to upper layers
This is mainly for protocol testing purposes.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-01-12 00:50:45 +02:00
Jouni Malinen
80f71b71d5 DPP: Authentication exchange retries and channel iteration in hostapd
This extends hostapd with previoiusly implemented wpa_supplicant
functionality to retry DPP Authentication Request/Response and to
iterate over possible negotiation channels.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-01-08 05:19:05 +02:00
Jouni Malinen
c5cc7a59ac Report offchannel RX frame frequency to hostapd
Not all code paths for management frame RX reporting delivered the
correct frequency for offchannel RX cases. This is needed mainly for
Public Action frame processing in some special cases where AP is
operating, but an exchange is done on a non-operational channel. For
example, DPP Initiator role may need to do this.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-01-08 03:37:48 +02:00
Jouni Malinen
02b38d0ad5 Fix MFP-enabled test for disallowed TKIP
The test against use of TKIP was done only in MFP-required
(ieee80211w=2) configuration. Fix this to check the pairwise cipher for
MFP-enabled (ieee80211w=1) case as well.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-12-27 18:38:12 +02:00
Jouni Malinen
ba3d435fe4 SAE: Add option to require MFP for SAE associations
The new hostapd.conf parameter sae_require_pmf=<0/1> can now be used to
enforce negotiation of MFP for all associations that negotiate use of
SAE. This is used in cases where SAE-capable devices are known to be
MFP-capable and the BSS is configured with optional MFP (ieee80211w=1)
for legacy support. The non-SAE stations can connect without MFP while
SAE stations are required to negotiate MFP if sae_require_mfp=1.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-12-27 18:27:58 +02:00
Jouni Malinen
c4fc7e31c7 SAE: Set special Sc value when moving to Accepted state
Set Sc to 2^16-1 when moving to Accepted state per IEEE Std 802.11-2016,
12.4.8.6.5 (Protocol instance behavior - Confirmed state). This allows
the peer in Accepted state to silently ignore unnecessary
retransmissions of the Confirm message.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-12-27 12:19:08 +02:00
Jouni Malinen
abcbd0604c SAE: Add Rc variable and peer send-confirm validation
This implements the behavior described in IEEE Std 802.11-2016,
12.4.8.6.6 (Protocol instance behavior - Accepted state) to silently
discard received Confirm message in the Accepted state if the new
message does not use an incremented send-confirm value or if the special
2^16-1 value is used. This avoids unnecessary processing of
retransmitted Confirm messages.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-12-27 12:19:08 +02:00
Jouni Malinen
9249afc8e1 SAE: Print state changes in debug log
This makes it easier to follow state changes in SAE protocol instances.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-12-27 00:07:42 +02:00
Jouni Malinen
d8b841eba8 SAE: Make dot11RSNASAESync configurable
The new hostapd.conf parameter sae_sync (default: 5) can now be used to
configure the dot11RSNASAESync value to specify the maximum number of
synchronization errors that are allowed to happen prior to
disassociation of the offending SAE peer.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-12-26 12:46:22 +02:00
Bhagavathi Perumal S
af832aa998 hostapd: Add average channel utilization in STATUS
This allows external programs to get the average channel utilization.
The average channel utilization is calculated and reported through
STATUS command. Users need to configure chan_util_avg_period and
bss_load_update_period in hostapd config to get the average channel
utilization.

Signed-off-by: Bhagavathi Perumal S <bperumal@qti.qualcomm.com>
2017-12-12 00:48:27 +02:00
Bhagavathi Perumal S
802c0fd0c3 hostapd: Update BSS load update period dynamically
Recalculate the timeout value for each event instead of calculating this
once and then not allowing the timeout configuration to be changed
without fully stopping and restarting the interface.

This allows the bss_load_update_period configuration parameter to be
modified while a BSS continues operating.

Signed-off-by: Bhagavathi Perumal S <bperumal@qti.qualcomm.com>
2017-12-12 00:48:25 +02:00
Jouni Malinen
778d87054e Fix error handling in bss_load_update_period parser
Do not update the configuration parameter before having verified the
value to be in the valid range.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-12-12 00:46:21 +02:00
Jouni Malinen
04ded82efa OWE: Fix error case handling with drivers that implement AP SME
owe_auth_req_process() can return NULL in error cases, but the caller
was not prepared for this. The p pointer cannot be overridden in such
cases since that would result in buffer length (p - buf) overflows. Fix
this by using a temporary variable to check the return value before
overriding p so that the hostapd_sta_assoc() ends up using correct
length for the IE buffer.

Fixes: 33c8bbd8ca ("OWE: Add AP mode handling of OWE with drivers that implement SME")
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-12-11 13:41:10 +02:00
Jouni Malinen
e5c7c2f28e Fix ap-mgmt-fuzzer build
Add src/ap/eth_p_oui.o into libap.a to be able to link ap-mgmt-fuzzer.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-12-09 18:41:55 +02:00
Jouni Malinen
402c8e00b7 WPS: Map GCMP-256 and CCMP-256 to AES encryption type
This is needed to allow a credential to be built for GCMP-256/CCMP-256
networks that do not enable GCMP-128/CCMP-128.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-12-02 12:00:45 +02:00
Shiva Sankar Gajula
a2660890a5 WPS: Allow WPS to be enabled in CCMP-256 and GCMP-256 only cases
Extend the check against WPA/TKIP only configuration by adding CCMP-256
and GCMP-256 to the list of allowed ciphers. This is needed to allow WPS
to be enabled in AP configurations where neither CCMP-128 nor GCMP-128
are enabled.

Signed-off-by: Shiva Sankar Gajula <sgajula@qti.qualcomm.com>
2017-12-02 12:00:44 +02:00
Jouni Malinen
ed62d40116 DPP: Deinit PKEX instance on DPP_STOP_LISTEN
Previously this stopped only the DPP Authentication instance, but it is
better to clear both PKEX and Authentication.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-29 12:24:01 +02:00
Jouni Malinen
634a130a52 DPP: Clear authentication instance on configuration completion in AP
wpa_supplicant was already doing this and hostapd needs to clear
hapd->dpp_auth when completing the exchange in Configurator (GAS server)
role.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-27 20:33:43 +02:00
Jouni Malinen
d3cb7ebe1b DPP: Do not process dpp_auth_ok_on_ack multiple times
An additional TX status callback could result in processing the DPP
authentication completion another time at least with hostapd. Fix this
by clearing the dpp_auth_ok_on_ack when processing it.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-27 20:20:26 +02:00
Jouni Malinen
a2588be82c DPP: Add DPP_CONFIGURATOR_SIGN support to hostapd
Configurator signing its own Connector was previously supported only in
wpa_supplicant. This commit extends that to hostapd to allow an AP
acting as a Configurator to self-configure itself.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-27 13:24:20 +02:00
Jouni Malinen
7eb6bfb45d DPP: Move hostapd Configurator/bootstrap data into global context
This moves the Configurator and Bootstrapping Information data from
struct hostapd_data (per-BSS) to struct hapd_interfaces (per-hostapd
process). This allows the information to be maintained over interface
restarts and shared between interfaces.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-27 13:24:20 +02:00
Bhagavathi Perumal S
0bd7f104c1 hostapd: Add supported rate information into STATUS and STA
These allow external programs to determine supported legacy, HT, and VHT
rates of an interface or a STA.

Signed-off-by: Bhagavathi Perumal S <bperumal@qti.qualcomm.com>
2017-11-25 13:25:09 +02:00
Jouni Malinen
1489fcf87d FILS: Do not leave error value in left counter
If fils_decrypt_assoc() were to fail on the AP side, the previous
implementation could have continued through the response generation
using left = -1. That could have resulted in unexpected processing if
this value were to be used as the length of the remaining (unencrypted)
IEs. Fix this by not updating left in the failure case.

Fixes: 78815f3dde ("FILS: Decrypt Association Request elements and check Key-Auth (AP)")
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-24 12:26:38 +02:00
Jouni Malinen
beae255a72 WPA: Check wpa_eapol_key_mic() result on TX
Verify that nothing unexpected happened with EAPOL-Key Key MIC
calculation when transmitting EAPOL-Key frames from the Authenticator.
This should not be able to happen in practice, but if if it does, there
is no point in sending out the frame without the correct Key MIC value.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-24 12:13:26 +02:00
Jouni Malinen
af4103e5e9 DPP: Provide peer_mac to PKEX Initiator through function argument
Avoid unnecessary direct write to a struct dpp_pkex member from outside
dpp.c.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-23 23:32:33 +02:00
Jouni Malinen
3ca4be1eaa DPP: Remove compiler warnings about signed/unsigned comparisons
These timestamp comparisons did not use matching signedness.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-23 20:31:12 +02:00
Hu Wang
63dc0f9c4d hostapd: Disassoc STA without WPA/RSN IE if AP proto is WPA/RSN
With the AP proto configured being WPA/RSN and SME in the
driver, the previous implementation in hostapd is to not
process hostapd_notif_assoc() due to "No WPA/RSN IE from STA",
if the (Re)Association Request frame is without the WPA/RSN IEs.

Enhance that to disassociate such station provided the AP is not using
WPS.

Signed-off-by: Hu Wang <huw@codeaurora.org>
2017-11-23 20:12:34 +02:00
bhagavathi perumal s
cc79e06f00 hostapd: Add wpa_msg_ctrl() to report Probe Request frames from STA
This allows external applications to get event indication for Probe
Request frames. Extend ctrl iface cmd "ATTACH" to enable this event on
per-request basis. For example, user has to send ctrl iface cmd "ATTACH
probe_rx_events=1" to enable the Probe Request frame events.

Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
2017-11-23 20:12:34 +02:00
Jouni Malinen
e3a5882b3e DPP: Add SAE credential support to Configurator
The new conf={sta,ap}-{sae,psk-sae} parameter values can now be used to
specify that the legacy configuration object is for SAE.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-22 21:24:08 +02:00
Jouni Malinen
5dd745b738 DPP: Add akm=sae and akm=psk+sae support in Enrollee role
This allows DPP to be used for enrolling credentials for SAE networks in
addition to the legacy PSK (WPA-PSK) case. In addition, enable FT-PSK
and FT-SAE cases automatically.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-22 21:23:51 +02:00
Jouni Malinen
4b8de0c929 DPP: Protocol testing for invalid Peer Discovery Req/Resp values
Extend dpp_test to allow more invalid attribute values to be written
into Peer Discovery Request/Response frames.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-19 17:15:02 +02:00
Jouni Malinen
c6eb3e34b6 Stronger GTK derivation routine
If the build include SHA384, use that to derive GTK from GMK. In
addition, add more random bytes bytes to the PRF-X() context data for
longer GTK to reduce dependency on the randomness of the GMK.

GMK is 256 bits of random data and it was used with SHA256, so the
previous design was likely sufficient for all needs even with 128 bits
of additional randomness in GTK derivation. Anyway, adding up to 256
bits of new randomness and using SHA384 can be helpful extra protection
particularly for the cases using GCMP-256 or CCMP-256 as the group
cipher.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-11-18 17:50:09 +02:00
Jouni Malinen
27781c0ab5 Allow group cipher selection to be overridden
The new hostapd configuration parameter group_cipher can now be used to
override the automatic cipher selection based on enabled pairwise
ciphers. It should be noted that selecting an unexpected group cipher
can result in interoperability issues and this new capability is mainly
for testing purposes.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-17 12:31:41 +02:00
Jouni Malinen
c1d3773967 DPP: Stop authentication exchange of DPP_STOP_LISTEN
Previously, this command stopped listen operation immediately, but if
there was an ongoing authentication exchange, a new listen operation was
started. This is not really expected behavior, so stop the
authentication exchange first with this command to avoid restarting
listen operation.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-13 12:35:26 +02:00
Jouni Malinen
d1f082644c DPP: Allowed initiator to indicate either role
The new role=either parameter can now be used with DPP_AUTH_INIT to
indicate that the initiator can take either the Configurator or Enrollee
role.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-13 11:45:05 +02:00
Jouni Malinen
f97ace34cb DPP: Support multiple channels for initiating DPP Authentication
This extends wpa_supplicant to iterate over all available channels from
the intersection of what the peer indicates and the local device
supports when initiating DPP Authentication. In addition, retry DPP
Authentication Request frame up to five times if no response is
received.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-13 11:45:05 +02:00
Jouni Malinen
a306ed5a58 DPP: Protocol testing to allow missing attributes in peer discovery
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-06 12:40:18 +02:00
Jouni Malinen
1fafdf1124 DPP: Add DPP_LISTEN and DPP_STOP_LISTEN to hostapd
This is an initial step in allowing non-operating channel operations
with DPP when hostapd is the Responder. For now, this is only used for
specifying role=configurator/enrollee and qr=mutual cases similarly to
the wpa_supplicant configuration for in Responder role. Request to use a
non-operating channel will be rejected.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-04 12:33:03 +02:00
Jouni Malinen
29ab69e4b0 DPP: PKEX counter t
Add limit on number of failed attempts that could have used PKEX code.
If the limit (5) is reached, drop the PKEX state (including the code)
and report this on the control interface to indicate that a new code
needs to be entered due to possible attack.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-03 19:59:46 +02:00
Jouni Malinen
039b8e7369 DPP: Terminate PKEX exchange on detection of a mismatching code
Clean up the pending PKEX exchange if Commit-Reveal Request processing
indicates a mismatch in the PKEX code. Previously, the this case was
silently ignored and the session was left in pending state that
prevented new PKEX exchanges from getting initated. Now, a new attempt
is allowed to be initiated.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-03 19:59:46 +02:00
Jouni Malinen
e0247e7983 DPP: PKEX and STATUS_BAD_GROUP
Report mismatching finite cyclic group with PKEX Exchange Response using
STATUS_BAD_GROUP and provide more detailed error report over the control
interface on the peer device when this happens.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-03 19:59:46 +02:00
Jouni Malinen
fe12ae777f Fix Status Code in TKIP countermeasures case
The previously used WLAN_REASON_MICHAEL_MIC_FAILURE (14) value as a
response to Authentication frame or (Re)Association Request frame is not
correct since the resp value is encoded in the Status Code (not Reason
Code) field. Status Code 14 is WLAN_STATUS_UNKNOWN_AUTH_TRANSACTION
which is really what this value would have meant in the response frames.

There is no Michael MIC failure status code, so have to use the generic
"Unspecified failure" (1) reason code for these cases.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-03 19:59:46 +02:00
Jouni Malinen
06f2df0693 DPP: Fix hostapd control interface events for initiator case
Incorrect msg_ctx was registered for the wpa_msg() calls from the DPP
module.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-02 12:25:35 +02:00
Jouni Malinen
219d4c9fcb DPP: Report possible PKEX code mismatch in control interface
Indicate to upper layers if PKEX Commit-Reveal Request frame AES-SIV
decryption fails. That is a likely sign of the PKEX code mismatch
between the devices.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-02 12:25:35 +02:00
Lior David
0c3bc1be09 Fix test build breakage when not compiling with ieee80211w support
Build breakage was introduced by commit
d8afdb210e ('Allow EAPOL-Key messages 1/4
and 3/4 to be retransmitted for testing') for some
CONFIG_TESTING_OPTIONS=y builds without CONFIG_IEEE80211W=y.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2017-11-01 12:50:20 +02:00
bhagavathi perumal s
ea4ace9c76 hostapd: Add max_txpower into STATUS command
Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
2017-10-31 11:49:41 +02:00
bhagavathi perumal s
bf6c65afce hostapd: Add Beacon interval and DTIM period into STATUS command
Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
2017-10-31 11:45:29 +02:00
bhagavathi perumal s
c7ae2b3104 hostapd: Add HT/VHT capability info into STATUS command
Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
2017-10-31 11:41:38 +02:00
bhagavathi perumal s
1f91a8bdea hostapd: Add HT/VHT capability info into STA command
Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
2017-10-31 11:37:20 +02:00
bhagavathi perumal s
65f9db6bc2 hostapd: Add extended capabilities into STA command
Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
2017-10-31 00:31:31 +02:00
bhagavathi perumal s
d1f3a81446 hostapd: Add [HT] flag into STA command
Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
2017-10-31 00:28:46 +02:00
bhagavathi perumal s
ba72b4b126 hostapd: Add Min/Max Transmit Power Capability into STA command
This provides access to the Minimum/Maximum Transmit Power Capabilitie
fileds (the nominal minimum/maximum transmit power with which the STA
is capable of transmitting in the current channel; signed integer in
units of decibels relative to 1 mW).

Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
2017-10-31 00:22:58 +02:00
Ashok Kumar Ponnaiah
33c8bbd8ca OWE: Add AP mode handling of OWE with drivers that implement SME
Handle OWE DH exchange and key setup when processing the association
event from a driver that implements AP SME.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-30 23:24:42 +02:00
Ashok Kumar Ponnaiah
28d1264131 Check hostapd current_mode before dereferencing it in additional places
While most places using this should be for cases where the hw_features
functionality is required, there seem to be some paths that are getting
exposed in new OWE related operations where that might not be the case.
Add explicit NULL pointer checks to avoid dereferencing the pointer if
it is not set when operating with driver wrappers that do not provide
sufficient information.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-30 23:20:25 +02:00
Jouni Malinen
348c93847a AP-side workaround for WNM-Sleep Mode GTK/IGTK reinstallation issues
Normally, WNM-Sleep Mode exit with management frame protection
negotiated would result in the current GTK/IGTK getting added into the
WNM-Sleep Mode Response frame. Some station implementations may have a
vulnerability that results in GTK/IGTK reinstallation based on this
frame being replayed. Add a new hostapd configuration parameter that can
be used to disable that behavior and use EAPOL-Key frames for GTK/IGTK
update instead. This would likely be only used with
wpa_disable_eapol_key_retries=1 that enables a workaround for similar
issues with EAPOL-Key. This is related to station side vulnerabilities
CVE-2017-13087 and CVE-2017-13088. To enable this AP-side workaround,
set wnm_sleep_mode_no_keys=1.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-10-29 17:13:54 +02:00
Johannes Berg
3f5a1860a8 wpa_auth: Deplete group rekey eloop handler for strict rekeying
When strict group rekeying is in effect, every station that leaves will
cause a rekeying to happen 0.5 s after leaving. However, if a lot of
stations join/leave, the previous code could postpone this rekeying
forever, since it always re-registers the handling with a 0.5 s timeout.

Use eloop_deplete_timeout() to address that, only registering the
timeout from scratch if it wasn't pending.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-10-29 17:04:14 +02:00
Johannes Berg
92662fb281 Allow forcing group rekeying for testing purposes
In order to test the WoWLAN GTK rekeying KRACK mitigation, add a
REKEY_GTK hostapd control interface command that can be used at certain
points of the test.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-10-29 16:58:55 +02:00
Jouni Malinen
d270920692 DPP: Negotiation channel change request from Initiator
Allow the Initiator to request a different channel to be used for DPP
Authentication and DPP Configuration exchanges. This commit adds support
for this in wpa_supplicant with the optional neg_freq=<freq in MHz>
parameter in DPP_AUTH_INIT.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-29 16:08:02 +02:00
Jouni Malinen
e85b660129 DPP: Add DPP Status attribute into Peer Discovery Response
This was added in DPP tech spec v0.2.7 to allow result of network
introduction to be reported.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-29 12:16:15 +02:00
Jouni Malinen
26806abe85 DPP: Report invalid messages and failure conditions in control interface
This is useful for protocol testing purposes and UI needs to display
more detailed information about DPP exchanges.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-22 22:45:17 +03:00
Jouni Malinen
af48810ba3 DPP: Report transmitted messages as control interface events
This is helpful for testing purposes and also for upper layer components
that may want to show more detailed progress through a DPP exchange.
Both the DPP-TX and DPP-TX-STATUS events are provided.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-22 17:21:57 +03:00
Jouni Malinen
a707393494 DPP: Report received messages as control interface events
This is helpful for testing purposes and also for upper layer components
that may want to show more detailed progress through a DPP exchange.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-22 17:21:57 +03:00
Jouni Malinen
27fefbbb76 DPP: Remove unnecessary Wrapped Data checks from callers
Now that dpp_check_attrs() takes care of verifying that no attributes
are after the Wrapped Data attribute, the duplicated checks in hostapd
and wpa_supplicant side of the implementation can be removed.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-22 17:21:57 +03:00
Ben Greear
74e55b6585 Fix test build breakage when not compiling with mesh support
Build breakage was introduced by commit
16579769ff ('Add testing functionality for
resetting PN/IPN for configured keys') for some CONFIG_TESTING_OPTIONS=y
builds.

Signed-off-by: Ben Greear <greearb@candelatech.com>
2017-10-21 10:59:15 +03:00
Jouni Malinen
3d0fb95583 WNM: Ignore BSS Transition Management frames in bss_transition=0 case
The hostapd bss_transition parameter was previously used to control
advertisement of BSS Transition Management support, but it was not used
when processing BSS Transition Management Query/Response frames. Add an
explicit check during frame processing as well so that any misbehaving
station is ignored. In addition to bss_transition=1, allow mbo=1 to be
used to mark the functionality enabled.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-20 20:32:36 +03:00
Jouni Malinen
114f2830d2 WNM: Ignore WNM-Sleep Mode Request in wnm_sleep_mode=0 case
The hostapd wnm_sleep_mode parameter was previously used to control
advertisement of WNM-Sleep Mode support, but it was not used when
processing a request to use WNM-Sleep Mode. Add an explicit check during
request processing as well so that any misbehaving station is ignored.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-20 17:39:42 +03:00
Jouni Malinen
3d6953288b Extend RESEND_* test commands to allow forcing plaintext TX
This allows hostapd testing functionality to be forced to send out a
plaintext EAPOL-Key frame with the RESEND_* command. That can be useful
in seeing how the station behaves if an unencrypted EAPOL frame is
received when TK is already configured.

This is not really perfect since there is no convenient way of sending
out a single unencrypted frame in the current nl80211 design. The
monitor interface could likely still do this, but that's not really
supposed to be used anymore. For now, clear and restore TK during this
operation. The restore part is not really working correctly, though,
since it ends up clearing the TSC value on the AP side and that shows up
as replay protection issues on the station. Anyway, this is sufficient
to generate sniffer captures to analyze station behavior.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-19 18:32:16 +03:00
Jouni Malinen
4be5bc98a8 DPP: Update AES-SIV AD for PKEX frames
The protocol design was updated to protect the six octets in the header
before the attributes.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-19 18:32:16 +03:00
Jouni Malinen
dc4d271c6d DPP: Update AES-SIV AD for DPP Authentication frames
The protocol design was updated to protect the six octets in the header
before the attributes.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-18 22:51:30 +03:00
Jouni Malinen
6f234c1e2e Optional AP side workaround for key reinstallation attacks
This adds a new hostapd configuration parameter
wpa_disable_eapol_key_retries=1 that can be used to disable
retransmission of EAPOL-Key frames that are used to install
keys (EAPOL-Key message 3/4 and group message 1/2). This is
similar to setting wpa_group_update_count=1 and
wpa_pairwise_update_count=1, but with no impact to message 1/4
retries and with extended timeout for messages 4/4 and group
message 2/2 to avoid causing issues with stations that may use
aggressive power saving have very long time in replying to the
EAPOL-Key messages.

This option can be used to work around key reinstallation attacks
on the station (supplicant) side in cases those station devices
cannot be updated for some reason. By removing the
retransmissions the attacker cannot cause key reinstallation with
a delayed frame transmission. This is related to the station side
vulnerabilities CVE-2017-13077, CVE-2017-13078, CVE-2017-13079,
CVE-2017-13080, and CVE-2017-13081.

This workaround might cause interoperability issues and reduced
robustness of key negotiation especially in environments with
heavy traffic load due to the number of attempts to perform the
key exchange is reduced significantly. As such, this workaround
is disabled by default (unless overridden in build
configuration). To enable this, set the parameter to 1.

It is also possible to enable this in the build by default by
adding the following to the build configuration:

CFLAGS += -DDEFAULT_WPA_DISABLE_EAPOL_KEY_RETRIES=1

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-10-17 00:06:26 +03:00
Jouni Malinen
d8afdb210e Allow EAPOL-Key messages 1/4 and 3/4 to be retransmitted for testing
The new hostapd control interface commands "RESEND_M1 <addr>" and
"RESEND_M3 <addr>" can be used to request a retransmission of the 4-Way
Handshake messages 1/4 and 3/4 witht he same or modified ANonce (in M1).

This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-10-16 17:47:24 +03:00
Jouni Malinen
6bc2f00f44 Allow group key handshake message 1/2 to be retransmitted for testing
The new hostapd control interface command "RESEND_GROUP_M1 <addr>" can
be used to request a retransmission of the Group Key Handshake message
1/2 for the current GTK.

This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-10-16 17:47:24 +03:00
Jouni Malinen
16579769ff Add testing functionality for resetting PN/IPN for configured keys
This can be used to test replay protection. The "RESET_PN" command in
wpa_supplicant and "RESET_PN <addr>" command in hostapd resets the local
counters to zero for the last configured key. For hostapd, the address
parameter specifies which STA this operation is for or selects GTK
("ff:ff:ff:ff:ff:ff") or IGTK ("ff:ff:ff:ff:ff:ff IGTK").

This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-10-16 17:43:10 +03:00
Jouni Malinen
a0bf1b68c0 Remove all PeerKey functionality
This was originally added to allow the IEEE 802.11 protocol to be
tested, but there are no known fully functional implementations based on
this nor any known deployments of PeerKey functionality. Furthermore,
PeerKey design in the IEEE Std 802.11-2016 standard has already been
marked as obsolete for DLS and it is being considered for complete
removal in REVmd.

This implementation did not really work, so it could not have been used
in practice. For example, key configuration was using incorrect
algorithm values (WPA_CIPHER_* instead of WPA_ALG_*) which resulted in
mapping to an invalid WPA_ALG_* value for the actual driver operation.
As such, the derived key could not have been successfully set for the
link.

Since there are bugs in this implementation and there does not seem to
be any future for the PeerKey design with DLS (TDLS being the future for
DLS), the best approach is to simply delete all this code to simplify
the EAPOL-Key handling design and to get rid of any potential issues if
these code paths were accidentially reachable.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-10-16 02:03:47 +03:00
Jouni Malinen
2f1357fb62 FILS: Accept another (Re)Association Request frame during an association
The previous implementation ended up starting a new EAPOL-Key 4-way
handshake if the STA were to attempt to perform another association.
This resulted in immediate disconnection since the PTK was not ready for
configuring FILS TK at the point when EAPOL-Key msg 1/4 is sent out.
This is better than alloing the association to continue with the same TK
reconfigured, but not really ideal.

Address this potential sequence by not starting a new 4-way handshake on
the additional association attempt. Instead, allow the association to
complete, but do so without reconfiguring the TK to avoid potential
issues with PN reuse with the same TK.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-10-16 02:03:47 +03:00
Jouni Malinen
df94906201 Add MGMT_TX_STATUS_PROCESS command for testing purposes
This allows ext_mgmt_frame_handling=1 cases with hostapd to process TX
status events based on external processing. This is useful for increased
test coverage of management frame processing.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-10-16 02:03:47 +03:00
Jouni Malinen
0adc9b28b3 Fix PTK rekeying to generate a new ANonce
The Authenticator state machine path for PTK rekeying ended up bypassing
the AUTHENTICATION2 state where a new ANonce is generated when going
directly to the PTKSTART state since there is no need to try to
determine the PMK again in such a case. This is far from ideal since the
new PTK would depend on a new nonce only from the supplicant.

Fix this by generating a new ANonce when moving to the PTKSTART state
for the purpose of starting new 4-way handshake to rekey PTK.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-10-16 02:03:47 +03:00
Mathy Vanhoef
0e3bd7ac68 hostapd: Avoid key reinstallation in FT handshake
Do not reinstall TK to the driver during Reassociation Response frame
processing if the first attempt of setting the TK succeeded. This avoids
issues related to clearing the TX/RX PN that could result in reusing
same PN values for transmitted frames (e.g., due to CCM nonce reuse and
also hitting replay protection on the receiver) and accepting replayed
frames on RX side.

This issue was introduced by the commit
0e84c25434 ('FT: Fix PTK configuration in
authenticator') which allowed wpa_ft_install_ptk() to be called multiple
times with the same PTK. While the second configuration attempt is
needed with some drivers, it must be done only if the first attempt
failed.

Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
2017-10-16 02:03:47 +03:00
Jouni Malinen
c53eb94616 OWE: Remove forgotten developer debug prints
These were used during initial implementation testing and were not
supposed to get committed.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-11 23:43:59 +03:00
Jouni Malinen
2377c1caef SAE: Allow SAE password to be configured separately (AP)
The new sae_password hostapd configuration parameter can now be used to
set the SAE password instead of the previously used wpa_passphrase
parameter. This allows shorter than 8 characters and longer than 63
characters long passwords to be used. In addition, this makes it
possible to configure a BSS with both WPA-PSK and SAE enabled to use
different passphrase/password based on which AKM is selected.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-11 23:10:19 +03:00
Jouni Malinen
91cc34bf32 OWE: Allow set of enabled DH groups to be limited on AP
The new hostapd configuration parameter owe_groups can be used to
specify a subset of the allowed DH groups as a space separated list of
group identifiers.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-10 21:03:57 +03:00
Jouni Malinen
8c19ea3f21 DPP: Add the crypto suite field to the frames
This additional field was added to DPP Public Action frames in DPP tech
spec v0.2.3 to support cryptographic agility in the future.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-10 01:30:08 +03:00
Jouni Malinen
c77e2ff096 DPP: Remove C-sign-key expiry
This was removed in DPP tech spec v0.2.3.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-10 01:17:33 +03:00
Jouni Malinen
a891388184 OWE: Transition mode information based on BSS ifname
The owe_transition_bssid and owe_transition_ssid parameters can now be
replace with owe_transition_ifname to clone the BSSID/SSID information
automatically in case the same hostapd process manages both the OWE and
open BSS for transition mode.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-09 13:39:23 +03:00
Jouni Malinen
d90f10fa41 OWE: PMKSA caching in AP mode
This extends OWE support in hostapd to allow PMKSA caching to be used.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-09 12:12:54 +03:00
Jouni Malinen
7a12edd163 OWE: Support DH groups 20 (NIST P-384) and 21 (NIST P-521) in AP mode
This extends OWE support in hostapd to allow DH groups 20 and 21 to be
used in addition to the mandatory group 19 (NIST P-256).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-08 17:12:35 +03:00
Jouni Malinen
d8c8d85753 OWE: Include RSNE in (Re)Association Response frame
This is not normally done in RSN, but RFC 8110 seems to imply that AP
has to include OWE AKM in the RSNE within these frames. So, add the RSNE
to (Re)Association Response frames when OWE is being negotiated.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-08 17:12:35 +03:00
Jouni Malinen
ea079153f4 OWE: Add AP support for transition mode
The new owe_transition_bssid and owe_transition_ssid parameters can be
used to configure hostapd to advertise the OWE Transition Mode element.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-08 17:12:35 +03:00
Peng Xu
4a37463416 hostapd: Update HE capabilities and HE operation definition
Replace vendor-specific elements for HE capabilities and HE operation
elements with the P802.11ax defined element values. This version is
based on P802.11ax/D1.4.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-05 15:09:43 +03:00
bhagavathi perumal s
3567641ebb Add TX/RX rate info and signal strength into STA output
These allow external programs to fetch the TX and RX rate information
and signal strength for a specific STA through the hostapd control
interface command "STA <addr>". The values of these attributes are
filled in the response of nl80211 command NL80211_CMD_GET_STATION.

Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
2017-10-05 12:12:24 +03:00
Ilan Peer
fd35ed5bba AP: Remove unneeded check for 'added_unassociated'
In fils_hlp_finish_assoc() the station is already added to the
driver so it is not needed to check the 'added_unassociated'
flag.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2017-09-25 21:21:22 +03:00
Peng Xu
3de1566db8 FILS: Check req_ies for NULL pointer in hostapd_notif_assoc()
Add checking for NULL req_ies when FILS processing a driver ASSOC event
in hostapd_notif_assoc(). This was already done in number of old code
paths, but the newer FILS path did not handle this. Though, it is
unlikely that this code path would be reachable in practice since this
is all within sta->auth_alg == WLAN_AUTH_FILS_* check.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-19 15:28:58 +03:00
Jouni Malinen
6418400db9 Add hostapd tls_flags parameter
This can be used to set the TLS flags for authentication server.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-18 12:12:48 +03:00
Jouni Malinen
5030d7d9fd DPP: Allow raw hex PSK to be used for legacy configuration
The new psk=<hexdump> can be used as an alternative to pass=<passphrase>
when configuring the DPP Configurator with a legacy network parameters.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-15 17:54:31 +03:00
Jouni Malinen
039ab15fdf DPP: Add DPP-CONFOBJ-PASS/PSK events for hostapd legacy configuration
These control interface event messages can be used to allow hostapd AP
to be configured for legacy WPA2-Personal configuration with DPP.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-15 17:45:06 +03:00
Jouni Malinen
9824de57a4 Fix EAPOL-Key version check for a corner case with Suite B AKM
While the Suite B AKM is not really going to be used with CCMP-128 or
GCMP-128 cipher, this corner case could be fixed if it is useful for
some testing purposes. Allow that special case to skip the HMAC-SHA1
check based on CCMP/GCMP cipher and use the following AKM-defined check
instead.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-15 00:36:25 +03:00
Jouni Malinen
4cada9dcc1 FILS: Add DHss into FILS-Key-Data derivation when using FILS SK+PFS
This part is missing from IEEE Std 802.11ai-2016, but the lack of DHss
here means there would not be proper PFS for the case where PMKSA
caching is used with FILS SK+PFS authentication. This was not really the
intent of the FILS design and that issue was fixed during REVmd work
with the changes proposed in
https://mentor.ieee.org/802.11/dcn/17/11-17-0906-04-000m-fils-fixes.docx
that add DHss into FILS-Key-Data (and PTK, in practice) derivation for
the PMKSA caching case so that a unique ICK, KEK, and TK are derived
even when using the same PMK.

Note: This is not backwards compatible, i.e., this breaks PMKSA caching
with FILS SK+PFS if only STA or AP side implementation is updated.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-13 22:17:58 +03:00
Jouni Malinen
41b8191485 FILS: Update PMKID derivation rules for ERP key hierarchy establishment
IEEE Std 802.11ai-2016 had missed a change in the Pairwise key hierarchy
clause (12.7.1.3 in IEEE Std 802.11-2016) and due to that, the previous
implementation ended up using HMAC-SHA-1 -based PMKID derivation. This
was not really the intent of the FILS design and that issue was fixed
during REVmd work with the changes proposed in
https://mentor.ieee.org/802.11/dcn/17/11-17-0906-04-000m-fils-fixes.docx
that change FILS cases to use HMAC-SHA-256 and HMAC-SHA-384 based on the
negotiated AKM.

Update the implementation to match the new design. This changes the
rsn_pmkid() function to take in the more generic AKMP identifier instead
of a boolean identifying whether SHA256 is used.

Note: This is not backwards compatible, i.e., this breaks PMKSA caching
based on the initial ERP key hierarchy setup if only STA or AP side
implementation is updated. PMKSA caching based on FILS authentication
exchange is not impacted by this, though.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-13 22:17:58 +03:00
Jouni Malinen
49e6a55537 FILS: Add a space before MAC address to a HLP debug message
The "FILS: No pending HLP DHCP exchange with hw_addr" debug message was
missing a space before the following MAC address, so add that there to
make the message more readable.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-07 13:33:40 +03:00
Jouni Malinen
3648d8a185 SAE: Allow commit fields to be overridden for testing purposes
The new sae_commit_override=<hexdump> parameter can be used to force
hostapd to override SAE commit message fields for testing purposes. This
is included only in CONFIG_TESTING_OPTIONS=y builds.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-04 13:32:03 +03:00
Jouni Malinen
e75335384a SAE: Add testing code for reflection attack
Allow hostapd to be configured to perform SAE reflection attack for SAE
testing purposes with sae_reflection_attack=1 configuration parameter.
This is included only in CONFIG_TESTING_OPTIONS=y builds.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-04 13:32:03 +03:00
Jouni Malinen
e61fea6b46 SAE: Fix PMKSA caching behavior in AP mode
Add PMKID into EAPOL-Key 1/4 when using SAE and fix the PMK-from-PMKSA
selection in some cases where PSK (from passphrase) could have been
used.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-04 13:32:03 +03:00
Jouni Malinen
7475e80f14 FILS: Fix wpa_supplicant AP build without CONFIG_IEEE80211W
CONFIG_FILS was missed as one of items requiring the p pointer in
hostapd_notif_assoc().

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-08-24 17:33:03 +03:00
Jouni Malinen
85fd8263a5 DPP: Use Transaction ID in Peer Discovery Request/Response frames
DPP tech spec changed the contents of these frames by replacing the
public key hash attributes with a Transaction ID attribute that gets
copied from the request to the response to identify the transaction in a
simpler manner.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-08-23 12:51:41 +03:00
Jouni Malinen
a4bf007877 DPP: Remove devices object from the connector
This was removed from the draft DPP tech spec, so remove it from the
implementation as well.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-08-22 23:46:27 +03:00
Avraham Stern
b5bf84ba39 WNM: Differentiate between WNM for station and for AP in build
Previously, CONFIG_WNM enabled build that supports WNM for both
station mode and AP mode. However, in most wpa_supplicant cases only
station mode WNM is required and there is no need for AP mode WNM.

Add support to differentiate between station mode WNM and AP mode
WNM in wpa_supplicant builds by adding CONFIG_WNM_AP that should be
used when AP mode WNM support is required in addition to station mode
WNM. This allows binary size to be reduced for builds that require
only the station side WNM functionality.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-07-18 13:28:09 +03:00
Ashwini Patil
65833d71a5 OCE: Add hostapd mode OCE capability indication if enabled
Add OCE IE in Beacon, Probe Response, and (Re)Association Response
frames if OCE is enabled in the configuration.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-14 21:27:00 +03:00
Naftali Goldstein
3f8e3a5486 ap: Fix invalid HT40 channel pair fallback
In case of incorrect HT40 configuration as part of an attempt to create
a 80 MHz AP, iface->conf->vht_oper_centr_freq_seg0_idx and
iface->conf->vht_oper_centr_freq_seg1_idx are zero'ed, but
iface->conf->vht_oper_chwidth remains VHT_CHANWIDTH_80MHZ. This causes
the logic in dfs_get_start_chan_idx to fail.

Fix this by setting iface->conf->vht_oper_chwidth to
VHT_CHANWIDTH_USE_HT when zero'ing the center frequency parameters.

Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
2017-07-08 16:06:38 +03:00
Ilan Peer
6d3e24d3e3 ap: Fix return value in hostapd_drv_switch_channel()
The documentation in driver.h state that in case of an error
-1 is returned.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2017-07-08 16:06:38 +03:00
Andrei Otcheretianski
bfbc41eace DPP: Fix compilation without openssl
dpp.h file requires openssl in order to compile, which breaks
compilation on systems without it.
Move DPP_OUI_TYPE to ieee802_11_defs.h and don't include dpp.h when
not really needed.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2017-07-07 23:37:45 +03:00
Jeffin Mammen
8b5ddda5fb FILS: Add HLP support with driver-based AP SME
This allows HLP processing to postpone association processing in
hostapd_notify_assoc().

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-06 15:24:42 +03:00
Jeffin Mammen
31ec556cef FILS: Fix the IP header protocol field in HLP DHCP response
The IP header should indicate that UDP is used in the message.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-06 14:00:30 +03:00
Jouni Malinen
b3e567c890 FILS: ERP-based PMKSA cache addition on AP
hostapd did not add a new PMKSA cache entry when FILS shared key
authentication was used, i.e., only the initial full authentication
resulted in a PMKSA cache entry being created. Derive the PMKID for the
ERP case as well and add a PMKSA cache entry if the ERP exchange
succeeds.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-05 17:52:23 +03:00
Jouni Malinen
bfe448331f FILS: Fix a frame name in a debug print
The EAP message included in FILS Wrapped Data from the non-AP STA to the
AP is EAP-Initiate/Re-auth.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-05 17:29:44 +03:00
Jouni Malinen
a86fb43ca3 DPP: DPP_BOOTSTRAP_INFO for hostapd
This extends the hostapd control interface to support the
DPP_BOOTSTRAP_INFO command that was recently added for wpa_supplicant.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-04 15:56:38 +03:00
Jouni Malinen
90f837b0bf Update default wpa_group_rekey to once-per-day when using CCMP/GCMP
The default value for GTK rekeying period was previously hardcoded to
600 seconds for all cases. Leave that short value only for TKIP as group
cipher while moving to the IEEE 802.11 default value of 86400 seconds
(once-per-day) for CCMP/GCMP.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-03 13:42:55 +03:00
Jouni Malinen
787615b381 DPP: Set PMKSA expiration based on peer connector
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-03 13:29:59 +03:00
Jouni Malinen
6b140f0fa2 DPP: Update hostapd configurator parameters to match wpa_supplicant
This updates the previously copied implementation to be up-to-date with
the more recent wpa_supplicant changes.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-03 13:15:12 +03:00
Jouni Malinen
2605405aa4 DPP: Configurator in hostapd
This integrates DPP configuration request processing into hostapd GAS
server implementation.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-03 13:03:35 +03:00
Jouni Malinen
efeada91a4 DPP: PKEX in hostapd
Allow hostapd to initiate and respond with PKEX bootstrapping similarly
to how this was implemented in wpa_supplicant.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-03 13:03:34 +03:00
Jouni Malinen
4ff89c2ebd DPP: Network Introduction protocol for hostapd
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:13:59 +03:00
Jouni Malinen
56c7549587 DPP: AP parameters for DPP AKM
Extend hostapd configuration to include parameters needed for the DPP
AKM: dpp_connector, dpp_netaccesskey, dpp_netaccesskey_expiry,
dpp_csign, dpp_csign_expiry.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:13:17 +03:00
Jouni Malinen
0c52953b0f DPP: Allow PMKSA cache entries to be added through hostapd ctrl_iface
This allows external programs to generate and add PMKSA cache entries
into hostapd. The main use for this is to run external DPP processing
(network introduction) and testing.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:13:17 +03:00
Jouni Malinen
567da5bbd0 DPP: Add new AKM
This new AKM is used with DPP when using the signed Connector to derive
a PMK. Since the KCK, KEK, and MIC lengths are variable within a single
AKM, this needs number of additional changes to get the PMK length
delivered to places that need to figure out the lengths of the PTK
components.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:13:17 +03:00
Jouni Malinen
9c2b8204e6 DPP: Integration for hostapd
This adds DPP bootstrapping, authentication, and configuration into
hostapd similarly to how the design was integrated in wpa_supplicant.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:13:17 +03:00
Vidyullatha Kanchanapally
115d5e2221 hostapd: Fix handling a 20/40 BSS Coexistence Management frame
hostapd processes a received 20/40 BSS Coexistence management frame, but
if no separate callbacks are registered for handling Public Action
frames it eventually sends a reply with MSB of category code set to 1
thinking that the received frame is an invalid frame. This could happen
based on whether hostapd was built and enabled with functionality using
the callback functions.

Fix this by explicitly returning 1 from the function when the 20/40 BSS
Coexistence Management frame is processed.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-05 08:04:44 +03:00
Sunil Dutt
2d18ab4082 Add a config parameter to exclude DFS channels from ACS
The new acs_exclude_dfs=1 parameter can be used to request hostapd to
exclude all DFS channels from ACS consideration. This is mainly of use
for cases where the driver supports DFS channels, but for some reason a
non-DFS channel is desired when using automatic channel selection.
Previously, the chanlist parameter could have been used for this, but
that required listing all the acceptable channels. The new parameter
allows this to be done without such a list.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-05-27 11:50:21 +03:00
Vasanthakumar Thiagarajan
04f667fcdd DFS: Allow switch to DFS channel after radar detection in ETSI
This is to comply with uniform spreading requirement for ETSI domain
(section 4.7.2.7 in EN 301 893 - V1.8.1). ETSI uniform spreading
requires equal probability for the usable channels. The previous channel
selection logic after a radar detection did not fully comply with the
uniform spreading requirement for the domain by ignoring DFS channels.
Consider DFS channels also during channel selection when the current DFS
domain is ETSI.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
2017-05-13 20:01:44 +03:00
Vasanthakumar Thiagarajan
aa56e36d66 driver: Make DFS domain information available to core
Current DFS domain information of the driver can be used in ap/dfs
to comply with DFS domain specific requirements like uniform spreading
for ETSI domain.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
2017-05-13 20:01:44 +03:00
Jouni Malinen
8fed47e013 FILS: Derive FT key hierarchy on authenticator side for FILS+FT
Derive PMK-R0 and the relevant key names when using FILS authentication
for initial FT mobility domain association.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-05-07 22:08:43 +03:00
Jouni Malinen
215eaa748b FILS: Implement FILS-FT derivation
This extends fils_pmk_to_ptk() to allow FILS-FT to be derived. The
callers do not yet use that capability; i.e., actual use will be added
in separate commits.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-05-07 17:04:29 +03:00
Jouni Malinen
80ddf5d995 FILS: Fix Key-Auth derivation for SK+PFS for authenticator side
The conditional gSTA and gAP (DH public keys) were not previously
included in Key-Auth derivation, but they are needed for the PFS case.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-05-07 17:04:29 +03:00
Michael Braun
3a46cf93d0 FT: Add support for wildcard R0KH/R1KH
Enable use of FT RRB without configuring each other AP locally. Instead,
broadcast messages are exchanged to discover APs within the local
network.

When an R0KH or R1KH is discovered, it is cached for one day.

When a station uses an invalid or offline r0kh_id, requests are always
broadcast. In order to avoid this, if r0kh does not reply, a temporary
blacklist entry is added to r0kh_list.

To avoid blocking a valid r0kh when a non-existing pmk_r0_name is
requested, r0kh is required to always reply using a NAK. Resend requests
a few times to ensure blacklisting does not happen due to small packet
loss.

To free newly created stations later, the r*kh_list start pointer in
conf needs to be updateable from wpa_auth_ft.c, where only wconf is
accessed.

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2017-05-03 22:16:14 +03:00
Michael Braun
eefe863015 FT RRB: Add msg replay and msg delay protection
This adds a counter and adds sequence numbering to FT RRB packets. The
sequence number is checked against r0kh/r1kh sequence number cache.

Special attention is needed in case the remote AP reboots and thus loses
its state. I prefer it to recover automatically even without synchronized
clocks. Therefore an identifier called dom is generated randomly along the
initial sequence number. If the dom transmitted does not match or the
sequence number is not in the range currently expected, the sender is asked
for a fresh confirmation of its currently used sequence numbers. The packet
that triggered this is cached and processed again later.

Additionally, in order to ensure freshness, the remote AP includes an
timestamp with its messages. It is then verified that the received
messages are indeed fresh by comparing it to the older timestamps
received and the time elapsed since then. Therefore FT_RRB_TIMESTAMP is
no longer needed.

This assigns new OUI 00:13:74 vendor-specific subtype 0x0001 subtypes:
4 (SEQ_REQ) and 5 (SEQ_RESP).

This breaks backward compatibility, i.e., hostapd needs to be updated
on all APs at the same time to allow FT to remain functional.

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2017-05-03 22:16:14 +03:00
Michael Braun
245fc96e5f FT: New RRB message format
Convert FT RRB into a new TLV based format. Use AES-SIV as AEAD cipher
to protect the messages.

This needs at least 32 byte long keys. These can be provided either
by a config file change or letting a KDF derive the 32 byte key used
from the 16 byte key given.

This breaks backward compatibility, i.e., hostapd needs to be updated on
all APs at the same time to allow FT to remain functional.

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2017-05-03 21:55:29 +03:00
Michael Braun
50bd8e0a90 FT: Replace inter-AP protocol with use of OUI Extended Ethertype
Replace the previously used extension of IEEE 802.11 managed Ethertype
89-0d (originally added for Remote Request/Response in IEEE 802.11r)
with Ethertype 88-b7 (OUI Extended EtherType) for FT inter-AP
communication. The new design uses a more properly assigned identifier
for the messages.

This assigns the OUI 00:13:74 vendor-specific subtype 0x0001 for the new
hostapd AP-to-AP communication purposes. Subtypes 1 (PULL), 2 (RESP),
and 3 (PUSH) are also assigned in this commit for the R0KH-R1KH
protocol.

This breaks backward compatibility, i.e., hostapd needs to be updated on
all APs at the same time to allow FT to remain functional.

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2017-05-03 18:30:31 +03:00
Jouni Malinen
f541148257 Fix GAS server ifdef block use
Commit 941caed980 ('MBO: Add MBO
ANQP-element processing on AP') changed the design by using the
rx_anqp_vendor_specific() function to process all ANQP vendor specific
elements. However, the caller for this was within ifdef CONFIG_HS20
block. Fix this by calling the function even in CONFIG_HS20=y is not
included in the build. This fixes CONFIG_MBO=y builds without
CONFIG_HS20=y.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-05-01 17:39:14 +03:00
Peng Xu
ec27b04e60 hostapd: Select a valid secondary channel if both enabled
When starting AP in HT40 mode and both HT40+ and HT40- options are
specified in hostapd.conf, select a valid secondary channel for the AP
automatically.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-29 16:35:23 +03:00
Jeffin Mammen
fa61bff6ae FILS: Handle authentication/association in partial driver AP SME
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-24 01:07:39 +03:00
Jeffin Mammen
5cee22ca47 FILS: Make handle_auth_fils() re-usable for driver-based AP SME
Allow this function to be called from outside ieee802_11.c and with the
final steps replaced through a callback function.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-24 01:07:39 +03:00
Jeffin Mammen
5e5f8c816b FILS: Move authentication response handling into a helper function
This can be reused when splitting handle_auth_fils() to support the
driver-based AP SME case.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-24 01:07:36 +03:00
Jeffin Mammen
b8a3453aca FILS: Pass only IE area to handle_auth_fils()
This function does not need the frame header, so pass in only the IE
area to make it easier to share this for driver-based AP SME handling.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-23 18:24:38 +03:00
Jeffin Mammen
9392859d7b FILS: Move AssocResp construction to a helper function
This can be reused from driver-based AP SME callback.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-23 18:20:00 +03:00
Jeffin Mammen
bd59935323 FILS: Move Key Confirm element validation to a helper function
This can be reused from driver-based AP SME callback.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-23 17:55:35 +03:00
Jeffin Mammen
087631b985 FILS: Move Session element validation to a helper function
This can be reused from driver-based AP SME callback.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-23 17:47:15 +03:00
Jeffin Mammen
cc20edc9f1 FILS: Add FILS auth_alg to driver-based AP SME association handling
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-23 17:47:15 +03:00
Jeffin Mammen
957bff83c4 FILS: Add driver-AP SME callback to set TK after association
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-23 17:47:15 +03:00
Jeffin Mammen
8acbf85fa2 FILS: Add FILS AEAD parameters for sta_auth() calls
This is used with partial AP SME in driver cases to enable FILS
association (AES-SIV) processing.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-23 17:47:15 +03:00
Jeffin Mammen
6b128fb2af driver: Move sta_auth() arguments to a struct
This makes it easier to add more parameters without having to change the
callback function prototype.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-23 17:47:12 +03:00
Jeffin Mammen
d5444aac4c FILS: Add FILS Indication element into Beacon/Probe Response template
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-21 18:44:59 +03:00
Jouni Malinen
5db997e343 FILS: Add FTE into FILS Authentication frame from AP when using FILS+FT
MDE was already added with RSNE, but FTE needed to be added to the FILS
Authentication frame for the FT initial mobility domain association
using FILS authentication case.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-04-02 22:38:48 +03:00
Jouni Malinen
5aa08153af FT: Add selection of FT+FILS AKMs
This is needed to enable use of FILS for the FT initial mobility domain
association.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-04-02 12:57:32 +03:00
Michael Braun
c5fee1604b FT: Schedule wpa_ft_rrb_rx() through eloop in intra-process communication
With AP-AP communication, when hapd0 sends a packet, hapd1 can receive
it immediately and send a response. But hapd0 will only read and process
the response after it has returned from the sending context, that is
entered eloop again. So one does not need to consider the RX function of
the reply to run for the request sending hapd before the send calling
function has returned.

Previously, with intra-process communication, the packet is not
scheduled through eloop. Thus the RX handler of the reply might be run
while the sending context of the original request has not returned.
This might become problematic, e.g., when deferring a management frame
processing until an RRB response is received and then have the request
restarted and finished before the original request handling has been
stopped.

I'm not aware of any concrete bug this is currently triggering but came
across it while thinking of FT RRB AP-AP sequence numbering.

I think the non-eloop scheduling approach might be error-prone and thus
propose to model it more closely to the way the message would be
received from a socket. Additionally, this ensures that the tests model
AP-AP communication more closely to real world.

Solution: queue these packets through eloop.

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2017-04-01 12:51:05 +03:00
Mohammed Shafi Shajakhan
775e986d5f hostapd: Fix crash on consecutive channel switch failures
With multiple interface like AP and station which is already
associated to some other AP, when we try to do channel switch
for the AP mode (different from the operation channel support of
station) and if the AP channel switch fails continously (including
the fallback channel switch), results in a crash due to NULL pointer
dereference. This is because hostapd_deinit_driver() assigns the
driver context (drv_priv) to NULL as we are not able to bring up
the interface with a new channel

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
2017-03-29 15:03:16 +03:00
Vidyullatha Kanchanapally
4cc6574d00 FILS: Fix fils_cache_id check
This fixes the following compiler warning:
wpa_auth.c:4249:34: error: address of array 'a->conf.fils_cache_id'
 will always evaluate to 'true' [-Werror,-Wpointer-bool-conversion]

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-03-26 21:13:21 +03:00
Jouni Malinen
1764559eef FILS: Add FILS SK auth PFS support in AP mode
This adds an option to configure hostapd to enable use of perfect
forward secrecy option in FILS shared key authentication. A new build
option CONFIG_FILS_SK_PFS=y can be used to include this functionality. A
new runtime configuration parameter fils_dh_group is used to enable this
by specifying which DH group to use. For example, fils_dh_group=19 would
allow FILS SK PFS to be used with a 256-bit random ECP group.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-03-12 23:20:32 +02:00
Jouni Malinen
07a5fe823e OWE: Use AKM 00-0F-AC:11 style parameters for EAPOL-Key frames
draft-harkins-owe-07.txt does not specify these parameters, so need to
pick something sensible to use for the experimental implementation. The
Suite B 128-bit level AKM 00-0F-AC:11 has reasonable parameters for the
DH group 19 case (i.e., SHA256 hash), so use it for now. This can be
updated if the OWE RFC becomes clearer on the appropriate parameters
(KEK/KCK/MIC length, PRF/KDF algorithm, and key-wrap algorithm).

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-03-12 20:43:06 +02:00
Jouni Malinen
ef9627cbc7 Print the algorithms used for EAPOL-Key professing in log
This makes it easier to debug crypto algorithm selection for 4-way
handshake related functions.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-03-12 20:43:06 +02:00
Jouni Malinen
09368515d1 OWE: Process Diffie-Hellman Parameter element in AP mode
This adds AP side processing for OWE Diffie-Hellman Parameter element in
(Re)Association Request frame and adding it in (Re)Association Response
frame.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-03-12 19:24:11 +02:00
Jouni Malinen
a1ea1b4522 OWE: Define and parse OWE AKM selector
This adds a new RSN AKM "OWE".

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-03-12 19:24:11 +02:00
Jouni Malinen
941caed980 MBO: Add MBO ANQP-element processing on AP
This extends the GAS server to process MBO ANQP-elements and reply to a
query for the Cellular Data Connection Preference (if configured). The
new configuration parameter mbo_cell_data_conn_pref can be used to set
the value (0, 1, or 255) for the preference to indicate.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-03-10 18:33:51 +02:00
Vasanthakumar Thiagarajan
7cbb5f1a44 DFS: Handle pre-CAC expired event
As FCC DFS requirement does not explicitly mention about the validity of
the (pre-)CAC when channel is switched, it is safe to assume that the
pre-CAC result will not be valid once the CAC completed channel is
switched or radar detection is not active on the (CAC completed) channel
within a time period which is allowed (10 seconds - channel switch time)
as per FCC DFS requirement.

Use the new driver event to allow the driver to notify expiry of the CAC
result on a channel. Move the DFS state of the channel to 'usable' when
processing pre-CAC expired event.  This means any future operation on
that channel will require a new CAC to be completed. This event is
applicable only when DFS is not offloaded to the kernel driver.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
2017-03-09 17:01:50 +02:00
Vasanthakumar Thiagarajan
3dcd735c1e DFS: Handle CAC completion event from other radio
When DFS channel state is shared across multiple radios on the system it
is possible that a CAC completion event is propagated from other radio
to us. When in enabled state, do not proceed with setup completion upon
processing CAC completion event with devices where DFS is not offloaded,
when in state other than enabled make sure the configured DFS channel is
in available state before start the AP.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
2017-03-09 16:46:30 +02:00
Johannes Berg
a1f11e34c4 Use os_memdup()
This leads to cleaner code overall, and also reduces the size
of the hostapd and wpa_supplicant binaries (in hwsim test build
on x86_64) by about 2.5 and 3.5KiB respectively.

The mechanical conversions all over the code were done with
the following spatch:

    @@
    expression SIZE, SRC;
    expression a;
    @@
    -a = os_malloc(SIZE);
    +a = os_memdup(SRC, SIZE);
    <...
    if (!a) {...}
    ...>
    -os_memcpy(a, SRC, SIZE);

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-07 13:19:10 +02:00
Jouni Malinen
4c803dfcd7 ACS: Fix memory leak if interface is disabled during scan
The survey data was not freed if hostapd interface got disabled during
an ACS scan.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-03-04 17:30:15 +02:00
Jouni Malinen
29be2c090e ACS: Simplify code paths
This removes some unnecessarily duplicated return paths and simplifies
code paths.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-03-04 17:30:10 +02:00
Jouni Malinen
d4359923e1 Fix DHCP/NDISC snoop deinit followed by failing re-init
It was possible to hit a double-free on the l2_packet socket if
initialization of DHCP/NDISC snoop failed on a hostapd interface that
had previously had those enabled successfully. Fix this by clearing the
l2_packet pointers during deinit.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-03-04 11:42:15 +02:00
Jouni Malinen
ff936bc753 Make the third octet of Country String configurable
The new hostapd.conf parameter country3 can now be used to configure the
third octet of the Country String that was previously hardcoded to ' '
(= 0x20).

For example:

All environments of the current frequency band and country (default)
country3=0x20

Outdoor environment only
country3=0x4f

Indoor environment only
country3=0x49

Noncountry entity (country_code=XX)
country3=0x58

IEEE 802.11 standard Annex E table indication: 0x01 .. 0x1f
Annex E, Table E-4 (Global operating classes)
country3=0x04

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-03-01 10:58:15 +02:00
Peng Xu
5b9f46df0e hostapd: Get channel number from frequency based on other modes as well
When getting the channel number from a frequency, all supported modes
should be checked rather than just the current mode. This is needed when
hostapd switches to a channel in different band.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-26 12:24:03 +02:00
Jouni Malinen
4c8836f139 FILS: Fix fils_hlp.c build with older netinet/udp.h definitions
The __FAVOR_BSD macro was previously used in netinet/udp.h to select
between two different names of the variables in struct udphdr. Define
that to force the versions with the uh_ prefix. In addition, use the
same style consistently within fils_hlp.c.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-26 12:18:29 +02:00
Jouni Malinen
57a2aacabf Add option to disable broadcast deauth in hostapd on AP start/stop
The new broadcast_deauth parameter can be used to disable sending of the
Deauthentication frame whenever AP is started or stopped. The default
behavior remains identical to the past behavior (broadcast_deauth=1).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-26 12:05:40 +02:00
Jouni Malinen
21ed24f5ad hostapd: Fix potential mesh-related change from impacting non-mesh cases
Commit 01e2231fdc ('hostapd: Skip some
configuration steps for mesh cases') removed some operations based on
hapd->iface->mconf being NULL. This was within #ifdef CONFIG_MESH, so it
should not impact hostapd, but it can impact AP mode with
wpa_supplicant. That does not sound intentional, so make these
conditional on hapd->conf->mesh being enabled.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-26 12:05:40 +02:00
Jouni Malinen
7eace3787c FILS: Find PMKSA cache entries on AP based on FILS Cache Identifier
This allows PMKSA cache entries to be shared between all the BSSs
operated by the same hostapd process when those BSSs use the same FILS
Cache Identifier value.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-21 12:18:58 +02:00
Peng Xu
d512f406fc hostapd: Add IEEE 802.11ax HE IEs into Beacon/Probe Response frames
IEEE 802.11ax HE changes to include HE IEs in Beacon and Probe Response
frames. These elements are using vendor specific forms for now since the
IEEE 802.11ax draft is not yet finalized and the element contents is
subject to change.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-19 17:37:55 +02:00
Peng Xu
94380cb40a hostapd: Initial IEEE 802.11ax (HE) definitions
Add IEEE 802.11ax definitions for config, IEEE structures, and
constants. These are still subject to change in the IEEE process.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-19 17:37:52 +02:00
Masashi Honma
5972dc73c1 mesh: Use correct rate in VHT and HT mixed environment
Let mesh STA A be a STA which has config disable_ht=0 and disable_vht=1.
Let mesh STA B be a STA which has config disable_ht=0 and disable_vht=0.
The mesh STA A and B was connected.

Previously, the mesh STA A sent frame with VHT rate even though its VHT
was disabled. This commit fixes the issue by checking the local BSS VHT
configuration.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2017-02-19 16:01:17 +02:00
Masashi Honma
84ea61cffe mesh: Use correct rate in HT and legacy mixed environment
Let mesh STA A be a STA which has config disable_ht=1.
Let mesh STA B be a STA which has config disable_ht=0.
The mesh STA A and B was connected.

Previously, the mesh STA A sent frame with HT rate even though its HT
was disabled. This commit fixes the issue by checking the local BSS HT
configuration.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2017-02-19 16:01:17 +02:00
Masashi Honma
a7a638c2c4 hw_features: Move VHT capabilities checks to common
This allows the previous AP-specific functions to be use for IBSS/mesh
setup in wpa_supplicant.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2017-02-19 15:53:05 +02:00
Jouni Malinen
a8e25deeb8 FT: Merge similar error paths to use common steps
Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-19 12:23:21 +02:00
Jouni Malinen
834c5d6816 FILS: Fix PMK length for initial connection with FILS SHA384 AKM
While the FILS authentication cases were already using the proper PMK
length (48 octets instead of the old hardcoded 32 octet), the initial
association case had not yet been updated to cover the new FILS SHA384
AKM and ended up using only a 32-octet PMK. Fix that to use 48-octet PMK
when using FILS SHA384 AKM.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-16 22:15:29 +02:00
Jouni Malinen
364c064a41 FT: Check key derivation results explicitly in AP operations
Previously, any potential (even if very unlikely) local operation error
was ignored. Now these will result in aborting the negotiation.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-14 16:33:01 +02:00
Jouni Malinen
885bbd4de3 WNM: Remove unused code from BSS TM Req generation
The url argument to ieee802_11_send_bss_trans_mgmt_request() was
hardcoded to NULL in the only caller, so this code cannot be reached.
wnm_send_bss_tm_req() construct the same frame with more generic
parameters, including option for including the URL, so
ieee802_11_send_bss_trans_mgmt_request() can be simplified.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-12 17:44:56 +02:00
Jouni Malinen
e7ddd86a98 WNM: Use a common error path in ieee802_11_send_wnmsleep_resp()
Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-12 17:44:56 +02:00
Jouni Malinen
d6d5970e23 WNM: Fix WNM-Sleep Mode Request parsing for WNM-Sleep element
The length of the WNM-Sleep element was not verified before using it.
This could result in reading the subfields in this element (total of
four octets) beyond the end of the buffer. Fix this by ignoring the
element if it is not long enough to contain all the subfields.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-12 17:44:56 +02:00
Jouni Malinen
8492cc79c0 PeerKey: Remove dead code related to STSL negotiation state
The struct wpa_stsl_negotiation seemed to have been for some kind of
tracking of state of PeerKey negotiations within hostapd. However,
nothing is actually adding any entries to wpa_auth->stsl_negotiations or
using this state. Since PeerKey does not look like something that would
be deployed in practice, there is no justification to spend time on
making this any more complete. Remove the dead code now instead of
trying to figure out what it might be used for.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-12 11:15:49 +02:00
Jouni Malinen
0d60567030 WMM: Fix estimated medium time calculation for some corner cases
It was possible for the int medium_time variable to overflow, so use a
64-bit unsigned integer to get a large enough value for the
multiplication.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-11 12:12:28 +02:00
Jouni Malinen
ae26d30213 Fix "IEEE 802.11: Ignored Action frame" debug message
The arguments to printf were in incorrect order which resulted in
incorrect STA address in the debug message.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-11 12:08:12 +02:00
Jouni Malinen
4ead4c7ecd WMM: Remove obsolete TODO comments
These are more about kernel behavior than anything that hostapd would
implement.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-11 10:29:18 +02:00
Jouni Malinen
401243b73e RRM: Fix range request overriding
This was supposed to cancel the existing eloop timeout instead of
registering another one.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-09 13:26:06 +02:00
Jouni Malinen
fb81c0a3d1 RRM: Merge similar error returns to a single one
There is no need to maintain different return paths for STA being
completely not present and not authorized, so merge these into a single
case.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-09 13:26:06 +02:00
Jouni Malinen
13b30052d9 RRM: Fix Range Request max age parsing
This 16-bit field uses little endian encoding and it must be read with
WPA_GET_LE16() instead of assuming host byte order is little endian. In
addition, this could be misaligned, so using a u16 pointer here was not
appropriate.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-09 13:26:06 +02:00
Jouni Malinen
bd6ec7f7ca Fix MAC ACL query freeing on deinit
hapd->acl_cache and hapd->acl_queries were not reset back to NULL in
hostapd_acl_deinit() when cached results and pending ACL queries were
freed. This left stale pointers to freed memory in hapd. While this was
normally followed by freeing of the hapd data, it is possible to re-use
that hapd when disabling and re-enabling an interface. That sequence
could result in use of freed memory if done while there were cached
results or pending ACL operations with a RADIUS server (especially, if
that server did not reply).

Fix this by setting hapd->acl_queries to NULL when the pending entries
are freed.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-08 23:48:19 +02:00
Jouni Malinen
0d6dc6830c FILS: Clean up HLP resize check
The "!wpabuf_resize(...) == 0" condition does not make any sense. It
happens to work, but this is really supposed to simple check with
wpabuf_resize() returns non-zero and "wpabuf_resize(...)" is the
cleanest way of doing so.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-07 20:50:33 +02:00
Jouni Malinen
65ab7eb1fa GAS: Fix OSU Providers List response with invalid configuration
If the OSU Providers configuration was invalid (included osu_server_uri
but not osu_method_list), it was possible for the GAS response
generation to hit a NULL dereference. Fix this by checking for the
invalid configuration before trying to fill in the OSU methods.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-07 17:47:58 +02:00
Günther Kelleter
4bb9b674c8 Add a log message when GTK rekeying failed
It can happen if the station is unreachable or sleeping longer than
the actual total GTK rekey timeout. To fix the latter case
wpa_group_update_count may be increased.

Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
2017-02-07 00:25:36 +02:00
Günther Kelleter
41f140d386 Add hostapd options wpa_group_update_count and wpa_pairwise_update_count
wpa_group_update_count and wpa_pairwise_update_count can now be used to
set the GTK and PTK rekey retry limits (dot11RSNAConfigGroupUpdateCount
and dot11RSNAConfigPairwiseUpdateCount). Defaults set to current
hardcoded value (4).

Some stations may suffer from frequent deauthentications due to GTK
rekey failures: EAPOL 1/2 frame is not answered during the total timeout
period of currently ~3.5 seconds. For example, a Galaxy S6 with Android
6.0.1 appears to go into power save mode for up to 5 seconds. Increasing
wpa_group_update_count to 6 fixed this issue.

Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
2017-02-07 00:25:36 +02:00
Eduardo Abinader
276e936548 hw_features: Clean center freq for falling back HT40 channels
Some channels fail to be set, when falling back to 20 MHz, due to
remaining VHT info of center freq. As we are going to 20 MHz, reset the
VHT center frequency segment information as well.

Signed-off-by: Eduardo Abinader <eduardoabinader@gmail.com>
2017-02-06 19:26:07 +02:00
Jouni Malinen
84bb12aa6d FILS: Fix send_assoc_resp() HLP extension to cover sta == NULL
Commit 91d91abf6f ('FILS: DHCP relay for
HLP requests') added steps that are conditional on sta->fils_hlp_resp
being non-NULL. One of these cases within send_assoc_resp() was properly
protected from sta == NULL error case (that is now possible after a
recent DMG change), but the first one was not. A DMG error case in a
CONFIG_FILS=y build could have hit a NULL pointer dereference here. Fix
this by verifying sta != NULL more consistently.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-05 16:40:15 +02:00
Jouni Malinen
caab23f192 Set EAPOL-Key Key Length field to 0 for group message 1/2 in RSN
P802.11i/D3.0 described the Key Length as having value 16 for the group
key handshake. However, this was changed to 0 in the published IEEE Std
802.11i-2004 amendment (and still remains 0 in the current standard IEEE
Std 802.11-2016). We need to maintain the non-zero value for WPA (v1)
cases, but the RSN case can be changed to 0 to be closer to the current
standard.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-05 13:52:43 +02:00
Jouni Malinen
b0fb2be77a Do not send GNonce in EAPOL-Key group message 1/2
While the IEEE Std 802.11-2016 is still indicating that GNonce would be
exchanged in EAPOL-Key messages (see, e.g., Figure 12-52 showing the
Send EAPOL-Key operation in the REKEYNEGOTIATING state or the sample
group key handshake in Figure 12-47), there are also examples of
describing this field as having value zero (e.g., 12.7.7.2 Group key
handshake message 1).

GNonce is used only with the Authenticator and the Supplicant does not
have any use for it, so it is better not to expose that internal value.
Hardcode the Key Nonce field to 0 in EAPOL-Key group message 1/2.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-05 13:39:57 +02:00
Jouni Malinen
3bbc470502 Fix EAPOL-Key Install bit in Group Key 1/2 with FT and FILS auth
sm->Pair needs to be initialized to TRUE since unicast cipher is
supported and this is an ESS. However, the normal place for setting this
(WPA_PTK::INITIALIZE) is skipped with using FT protocol or FILS
authentication, so need to do that separately when forcing PTKINITDONE.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-05 13:28:42 +02:00
Jouni Malinen
db5e53cb06 mesh: Fix struct hostapd_data initialization
The local custom version of allocating and initializing struct
hostapd_data within wpa_supplicant_mesh_init() is problematic. This has
already missed couple of initialization steps that are required. Instead
of trying to remember to keep this up to date, use
hostapd_alloc_bss_data() so that there is only one place for this
initialization.

This is fixing a recent issue where FILS HLP started using
hapd->dhcp_server and expected that to be initialized to -1. For the
mesh case, that did not happen and when removing the interface, the FILS
HLP implementation ended up unregistering eloop socket for
hapd->dhcp_server (= 0). This could result in missing socket callbacks
for an arbitrary socket.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-04 22:17:54 +02:00
Jouni Malinen
d77f330418 FILS: Fix AES-SIV AAD for (Re)Association Request frame decryption
The hostapd processing of the AES-SIV AAD was incorrect. The design for
the AAD changed between P802.11ai/D7.0 and D8.0 from a single vector
with concatenated data to separate vectors. The change in the
implementation had missed the change in the aes_siv_decrypt() call for
the num_elem parameter. This happened to work with the mac80211
implementation due to a similar error there.

Fix this by using the correct numbers of vectors in the SIV AAD so that
all the vectors get checked. The last vector was also 14 octets too long
due to incorrect starting pointer, so fix that as well. The changes here
are not backwards compatible, i.e., a similar fix in the Linux mac80211
is needed to make things interoperate again.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-04 13:09:52 +02:00
Jouni Malinen
91d91abf6f FILS: DHCP relay for HLP requests
The new dhcp_server configuration parameter can now be used to configure
hostapd to act as a DHCP relay for DHCPDISCOVER messages received as
FILS HLP requests. The dhcp_rapid_commit_proxy=1 parameter can be used
to configure hostapd to convert 4 message DHCP exchange into a 2 message
exchange in case the DHCP server does not support DHCP rapid commit
option.

The fils_hlp_wait_time parameter can be used to set the time hostapd
waits for an HLP response. This matches the dot11HLPWaitTime in IEEE Std
802.11ai-2016.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-01 18:17:39 +02:00
Jouni Malinen
54b04d6f39 FILS: Move HLP request handling into a separate file
This is independent functionality from the core IEEE 802.11 management
handling and will increase significantly in size, so it is cleaner to
maintain this in a separate source code file.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-01-31 17:46:13 +02:00
Jouni Malinen
5a9d504938 ProxyARP: Use more robust DHCP option parsing
Do not depend on undefined behavior with pointer arithmetic when
checking whether there is sufficient room for an option.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-01-31 17:46:13 +02:00
Jouni Malinen
e64c13febb Move DHCP definitions into a common file
These can be reused for other purposes than just the DHCP snoofing for
Proxy ARP. In addition, use more complete definition of the parameters
based on the current IANA registry.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-01-31 17:46:11 +02:00
Dedy Lansky
53d171440f AP: Check ACL upon association request for 802.11ad
With device_ap_sme disabled, ACL was checked upon authentication
request. In 802.11ad there is no authentication phase so need to check
ACL upon association.

Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
2017-01-30 22:22:40 +02:00
Daniel Kim
4cc61c3866 GAS: Set temporary session timeout bigger than gas_comeback_delay
Previously, the temporary STA session timeout was set to 5 seconds. If
gas_comeback_delay is configured to be longer than 5 seconds, GAS
Comeback Response frame can't include queried information as all pending
data has already been cleared due to session timeout. This commit
resolves the issue by setting session timeout to be larger than
gas_comeback_delay.

Signed-off-by: Daniel Kim <kimdan@qca.qualcomm.com>
2017-01-30 13:25:48 +02:00
Johannes Berg
cef8fac04b wpa_auth: Make struct wpa_auth_callbacks const
Instead of copying the struct wpa_auth_callbacks, just keep a pointer to
it, keep the context pointer separate, and let the user just provide a
static const structure. This reduces the attack surface of heap
overwrites, since the function pointers move elsewhere.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-01-29 18:41:26 +02:00
Johannes Berg
30eddf3529 Fix or supress various sparse warnings
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-01-29 18:33:10 +02:00
Jouni Malinen
5208160b4b FILS: Parse received FILS HLP requests
This adds parsing of received FILS HLP requests from (Re)Association
Request frames. The reassembled requests are verified to be in valid
format and are printed in debug output. However, actual processing or
forwarding of the packets is not yet implemented, i.e., the vendor
specific frame filtering logic is for now practically dropping all HLP
requests.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-01-29 14:32:17 +02:00
Masashi Honma
4d77d80edd mesh: Add MESH_PMKSA_GET/ADD commands
These commnds are mesh version of PMKSA_GET/ADD commands. So the usage
and security risk is similar to them. Refer to
commit 3459381dd2 ('External persistent
storage for PMKSA cache entries') also.

The MESH_PMKSA_GET command requires peer MAC address or "any" as an
argument and outputs appropriate stored PMKSA cache. And the
MESH_PMKSA_ADD command receives an output of MESH_PMKSA_GET and re-store
the PMKSA cache into wpa_supplicant. By using re-stored PMKSA cache,
wpa_supplicant can skip commit message creation which can use
significant CPU resources.

The output of the MESH_PMKSA_GET command uses the following format:
<BSSID> <PMKID> <PMK> <expiration in seconds>

The example of MESH_PMKSA_ADD command is this.
MESH_PMKSA_ADD 02:00:00:00:03:00 231dc1c9fa2eed0354ea49e8ff2cc2dc cb0f6c9cab358a8146488566ca155421ab4f3ea4a6de2120050c149b797018fe 42930
MESH_PMKSA_ADD 02:00:00:00:04:00 d7e595916611640d3e4e8eac02909c3c eb414a33c74831275f25c2357b3c12e3d8bd2f2aab6cf781d6ade706be71321a 43180

This functionality is disabled by default and can be enabled with
CONFIG_PMKSA_CACHE_EXTERNAL=y build configuration option.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2017-01-14 18:07:46 +02:00
Jouni Malinen
fa67debf4c Fix duplicate Reassociation Request frame dropping
Relational operators (==) have higher precedence than the ternary
conditional in C. The last_subtype check for association/reassociation
was broken due to incorrect assumption about the precedence. Fix this by
adding parenthesis around the ternary conditional.

The previous implementation worked for Association Request frames by
accident since WLAN_FC_STYPE_ASSOC_REQ happens to have value 0 and when
the last receive frame was an Association Request frame, the
sta->last_subtype == reassoc check was true and non-zero
WLAN_FC_STYPE_REASSOC_REQ was interpreted as true. However, this was
broken for Reassociation Request frame. reassoc == 1 in that case could
have matched received Association Response frame (subtype == 1), but
those are not received in AP mode and as such, this did not break other
behavior apart from not being able to drop duplicated Reassociation
Request frames.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-01-14 01:04:31 +02:00
Jouni Malinen
fcd3d6ce32 FILS: Fix PMK and PMKID derivation from ERP
This adds helper functions for deriving PMK and PMKID from ERP exchange
in FILS shared key authentication as defined in IEEE Std 802.11ai-2016,
12.12.2.5.2 (PMKSA key derivation with FILS authentication). These
functions is used to fix PMK and PMKID derivation which were previously
using the rMSK directly as PMK instead of following the FILS protocol to
derive PMK with HMAC from nonces and rMSK.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-01-13 21:07:40 +02:00
Jouni Malinen
167f78a5e8 Send BEACON-REQ-TX-STATUS event only for beacon reports
Check the action TX status callback contents more thoroughly and report
the BEACON-REQ-TX-STATUS event only if the Measurement Type indicates
beacon report.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-07 22:23:13 +02:00
Dedy Lansky
05e5e615e6 AP: Skip authentication/deauthentication phase for DMG/IEEE 802.11ad
Authentication and Deauthentication frames are not used in DMG/IEEE
802.11ad networks. For DMG/IEEE 802.11ad the following was implemented:
Upon receiving association request, allocate the sta object and
initialize it as if authentication took place. Upon receiving
disassociation, deallocate the sta object.
ap_sta_disassociate/ap_sta_deauthenticate/ap_sta_disconnect all use
disassociation instead of deauthentication. In driver_nl80211,
i802_sta_deauth() is routed to i802_sta_disassoc().

Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
2017-01-05 17:28:23 +02:00
Dedy Lansky
0c4b9025c1 AP: Do not look for supported rates in DMG/IEEE 802.11ad
Supported Rates element is not present in DMG/IEEE 802.11ad frames. Make
copy_supp_rates() immediately return with success if hardware mode is
IEEE 802.11ad.

Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
2017-01-05 17:05:00 +02:00
Jouni Malinen
ec45927b8a Report received beacon report with BEACON-RESP-RX event
The new hostapd control interface event "BEACON-RESP-RX <STA address>
<dialog token> <report mode> <beacon report>" is now used to report
received beacon reports as a reponse to the REQ_BEACON operation.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-03 16:02:58 +02:00
Jouni Malinen
f3383366aa Report beacon request TX status as control interface event
The new BEACON-REQ-TX-STATUS control interface event is now used to
report whether a beacon request (from REQ_BEACON command) was delivered
successfully. This event has the following parameters: <STA address>
<dialog token> <ack=0/1>.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-03 16:02:58 +02:00
Jouni Malinen
90d9d7c32a Beacon request through hostapd control interface
The new control interface command "REQ_BEACON <STA addr>
[req_mode=<mode>] <beacon request>" can now be used to request hostapd
to transmit a measurement request to request a beacon report from an
associated STA. This command returns the assigned dialog token (1-255)
or FAIL on failure.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-03 16:02:58 +02:00
Jouni Malinen
f56877414c Do not add own BSS in neighbor report with invalid op_class/channel
Verify that ieee80211_freq_to_channel_ext() succeeds before adding the
own BSS in the neighbor report.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-03 15:18:30 +02:00
Jouni Malinen
aeff0645d2 FILS: Fix FILS Realm Information ANQP-element construction
The loop to add hash values was supposed to be limited to at most 10000
values, but the count variable was not being decremented in the loop.
Fix this by decrementing counting for each iteration. This fixes
ANQP-element format in the unlikely case of there being more than 10000
configuration realms.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-03 15:18:30 +02:00
Jouni Malinen
2977f5193a GAS: Remove unnecessarily duplicate gas_frag_limit configuration
The actual BSS configuration parameter can be updated with the SET
control interface command, so there is no need to maintain a separate
per-BSS parameter and a separate control interface handling for this.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-30 00:23:10 +02:00
Jouni Malinen
1940559ea4 FT: Drop FT Action frames if ft_over_ds=0
Previously, the hostapd ft_over_ds parameter was used to only advertise
whether FT-over-DS is enabled in MDE and leave it to the stations to
follow that advertisement. This commit extends this to explicitly reject
(silently drop) FT Action frames if a station does not follow the
advertised capabilities.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-29 01:13:59 +02:00
Jouni Malinen
78022c8366 Fix memory leak on hostapd eap_user_file parsing error paths
Need to free all the pending completed EAP users if a parsing error
prevents the file from being used.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-28 14:47:00 +02:00
Jouni Malinen
95de34a10a Remove trailing whitespace
Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-28 14:31:42 +02:00
Jouni Malinen
9266d00bf9 hostapd: Reject invalid macaddr_acl value
Previously, this was noted in error log, but the invalid value was
stored in the configuration without rejecting it.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-27 11:43:13 +02:00
Jouni Malinen
1dfd25a68a Fix hostapd SIGHUP processing before interface is enabled
It was possible to try to do driver operations before the driver
interface had been initialized when processing a SIGHUP signal. This
would result in NULL pointer dereference. Fix this by skipping the steps
when SIGHUP is issued before the interface is enabled.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-27 11:16:51 +02:00
Jouni Malinen
34e29dfd4b Remove unnecessary NULL check from hostapd_config_read_wpa_psk() call
This function is already checking the fname argument against NULL, so
use that check on its own instead of duplicating the check in the only
caller.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-26 17:42:41 +02:00
Jouni Malinen
1f0fdaf0e4 Fix race condition between AssocResp callback and 4addr event
It is apparently possible for the NL80211_CMD_UNEXPECTED_4ADDR_FRAME
event to be delivered to hostapd before the NL80211_CMD_FRAME_TX_STATUS
event for (Re)Association Response frame. This resulted in the 4-address
WDS mode not getting enabled for a STA. This could occur in particular
when operating under heavy load and the STA is reconnecting to the same
AP in a sequence where Deauthentication frame is followed immediately by
Authentication frame and the driver event processing gets delayed due to
removal of the previous netdev taking time in the middle of this
sequence.

Fix this by recording a pending item for 4-address WDS enabling if the
NL80211_CMD_UNEXPECTED_4ADDR_FRAME event would have been dropped due to
incompleted association and then process this pending item if the TX
status for the (Re)Association Response frame is received and it shows
that the frame was acknowledged.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-12-20 01:30:09 +02:00
Jouni Malinen
8183aee6cc FILS: Add support for building FILS Realm Information ANQP-element
This allows full list of hashed realm names to be fetched from hostapd.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-18 11:41:59 +02:00
Jouni Malinen
26bf70e3d2 FILS: Separate FILS realm configuration from ERP domain
The new hostapd configuration parameter fils_realm=<realm> can now be
used to configure one or more FILS realms to advertise for ERP domains
when using FILS. This replaces the use of erp_domain=<domain> parameter
for the FILS use case.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-17 22:08:23 +02:00
Jouni Malinen
42b847ac1e FILS: Fix hashed realm name derivation
P802.11ai/D7.0 changed from CRC32 to SHA256 as the hash algorithm for
the FILS realm name. Update the implementation to match that change.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-17 22:07:57 +02:00
Jouni Malinen
cebda0e3e5 Make debug print clearer for AP/mesh mode secondary channel issues
If the secondary channel was not found at all, no debug print was shown
to indicate that the channel was rejected due to that problem. Print a
clearer message indicating which channel was behind the reason to reject
channel configuration as unsuitable for AP mode.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-12-13 15:09:15 +02:00
Daisuke Niwa
655dc4a432 Send "TERMINATING" event from hostapd
hostapd didn't send "TERMINATING" event when stopped by
SIGTERM. Android handles this event to stop monitor thread.

This commit adds "TERMINATING" event same as with wpa_supplicant.

Signed-off-by: Tomoharu Hatano <tomoharu.hatano@sonymobile.com>
2016-12-12 20:32:28 +02:00
Jouni Malinen
0f5eb69f85 Use eloop timeout for post-EAP-Failure wait before disconnection
Previously, os_sleep() was used to block the hostapd (or wpa_supplicant
AP/P2P GO mode) processing between sending out EAP-Failure and
disconnecting the STA. This is not ideal for couple of reasons: it
blocks all other parallel operations in the process and it leaves a
window during which the station might deauthenticate and the AP would
have no option for reacting to that before forcing out its own
Deauthentication frame which could go out after the STA has already
started new connection attempt.

Improve this design by scheduling an eloop timeout of 10 ms instead of
the os_sleep() call and perform the delayed operations from the eloop
callback function. This eloop timeout is cancelled if the STA
disconnects or initiates a new connection attempt before the 10 ms time
is reached. This gets rid of the confusing extra Deauthentication frame
in cases where the STA reacts to EAP-Failure by an immediate
deauthentication.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-08 18:56:02 +02:00
Michael Braun
34f7c699a6 Add multicast to unicast support
This adds support for nl80211 NL80211_CMD_SET_MULTICAST_TO_UNICAST
command.

By setting the new hostapd configuration option multicast_to_unicast=1,
hostapd configures this AP to perform multicast to unicast conversion.

When enabled, all multicast packets with ethertype ARP, IPv4, or IPv6
(possibly within an 802.1Q header) will be sent out to each station once
with the destination (multicast) MAC address replaced by the station's
MAC address. Note that this may break certain expectations of the
receiver, e.g., the ability to drop unicast IP packets encapsulated in
multicast L2 frames, or the ability to not send destination unreachable
messages in such cases.

This also does not implement Directed Multicast Service (DMS).

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2016-12-04 21:00:06 +02:00
Sam Tannous
08032c7418 Remove inactivity timeout for wired interfaces
We should unconditionally remove inactivity timers for wired network
cases. This commit checks for this after a new station association:

   hapd->iface->drv_flags & WPA_DRIVER_FLAGS_WIRED

and then cancels the timeout and does not register a new one.

It prints out a debug message like this:

1476740180.276286: IEEE 802.1X: 00:02:00:00:00:07 CTRL_DIR entering
state FORCE_BOTH
1476740180.276295: hostapd_new_assoc_sta: canceled wired ap_handle_timer
timeout for 00:02:00:00:00:07

This was tested on a debian jessie amd64 system with a configured 120
second inactivity timer and the session did not timeout.

Signed-off-by: Sam Tannous <stannous@cumulusnetworks.com>
2016-12-04 20:38:45 +02:00
Jouni Malinen
cb2b666670 Fix 4addr reassociation-without-deauthentication on AP
Data connection was lost if a station reassociated without the STA entry
being cleaned up on the AP side. Fix this by moving reconfiguration of
the STA WDS parameters in association response callback to happen only
after the STA flags have been updated to associated stated.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-12-02 12:51:16 +02:00
Jouni Malinen
2ab09656ae AP: Do not drop STA entry if PMF is used with full AP client state
This fixes a regression from commit
bb598c3bdd ('AP: Add support for full
station state'). That commit added code to remove and re-add the kernel
STA entry when processing Authentication frames with a driver that
advertises support for full AP client state. That resulted in bypassing
PMF protections for unprotected Authentication frames with such drivers
since the TK was lost in this operation.

It is simplest to skip the STA entry clearing in this type of case
completely to leave the TK in place and to process the new
authentication exchange otherwise normally. This matches the behavior
used with the drivers that do not implement full AP client state.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-11-29 16:26:00 +02:00
Will Glynn
209dad066e FT: Explicitly check for MDE not present in non-FT association
IEEE Std 802.11-2012, 12.4.2 states that if an MDE is present in an
(Re)Association Request frame but the RSNE uses a non-FT AKM suite, the
AP shall reject the association using status code 43 ("Invalid AKMP").

wpa_validate_wpa_ie() now explicitly checks for this condition to meet
this requirement instead of simply ignoring the MDE based on non-FT AKM.

Signed-off-by: Will Glynn <will@willglynn.com>
2016-11-26 11:39:44 +02:00
Purushottam Kushwaha
29483a5678 Add support for user configurable Beacon frame data rate for AP mode
Allow configuration of Beacon frame TX rate from hostapd.conf with
"beacon_rate=xx" option. The following format is used to set
legacy/HT/VHT beacon rates:

Legacy (CCK/OFDM rates):
	beacon_rate=<legacy rate in 100 kbps>
HT:
	beacon_rate=ht:<HT MCS>
VHT:
	beacon_rate=vht:<VHT MCS>

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-11-25 23:12:30 +02:00
Jouni Malinen
4051dd8667 GAS: Add Capability List ANQP-element support for Info ID 270, 280..299
This extends the anqp_elem configuration parameter support for new Info
IDs (270 (TDLS Capability) was previously missed from the list of
defined values, 280 has already been assigned in REVmc/D8.0; 281..299
are yet to be assigned). No additional source code changes are needed to
allow hostapd to advertise support for these if the ANQP-element value
is set with the anqp_elem parameter.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-11-17 16:00:25 +02:00
Jouni Malinen
d50f518e95 Fix libap.a build
Add the new defines and files to allow src/ap/libap.a to be build with
all the needed functions.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-11-16 13:26:23 +02:00
Ilan Peer
4ec1fd8e42 FT: Differentiate between FT for station and for AP in build
Previously, CONFIG_IEEE80211R enabled build that supports FT for both
station mode and AP mode. However, in most wpa_supplicant cases only
station mode FT is required and there is no need for AP mode FT.

Add support to differentiate between station mode FT and AP mode FT in
wpa_supplicant builds by adding CONFIG_IEEE80211R_AP that should be used
when AP mode FT support is required in addition to station mode FT. This
allows binary size to be reduced for builds that require only the
station side FT functionality.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2016-10-29 22:14:54 +03:00
Beni Lev
f0259c3f68 hostapd: Fix own wide bandwidth subelement generation (neighbor report)
The Channel Center Frequency Segment subfields use the channel index
instead of frequency in MHz.

Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
2016-10-29 22:03:43 +03:00
Ilan Peer
0a63635ed0 AP: Use valid status code in wpa_ft_send_rrb_auth_resp()
The return value from this function may be used in an outgoing message,
so use a valid status code instead of -1.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2016-10-29 22:02:14 +03:00
David Spinadel
451a27b1ad hostapd: Add a configuration to set an AP as stationary
Add a configuration option in hostapd.conf and in neighbor report that
sets an AP as stationary. To enable this option on the current AP set
the config option stationary_ap to 1. To set a neighbor entry to be
marked as stationary add the word stat to the SET_NEIGHBOR command. This
option tells hostapd to send LCI data even if it is older than requested
by max age subelement in RRM request.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2016-10-29 19:16:47 +03:00
Ilan Peer
f5ec346902 hostapd: Fix adding neighbor entry
It is possible that a LCI or location civic configuration buffer
is valid but contains no data. In such a case do not add the LCI
and location civic information to the entry in the neighbor
data base.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2016-10-29 19:10:17 +03:00
Filip Matusiak
59d7cff7e3 AP: Disable VHT in TKIP-only configuration
This has already been done for WEP, but there's same constraint for not
allowing VTH rates in case of TKIP.

Signed-off-by: Filip Matusiak <filip.matusiak@tieto.com>
2016-10-29 00:55:49 +03:00
Kevin Mahoney
a818425d1c hostapd: Added signal level to STA tracking
Add signal level information to the station tracking information. Also
make it available via the "TRACK_STA_LIST" control command.

Signed-off-by: Kevin Mahoney <k.mahoney@cablelabs.com>
2016-10-29 00:55:49 +03:00
Nishant Chaprana
5f99d96287 Removed redundant NULL check for sta in hostapd_event_sta_low_ack()
Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
2016-10-28 19:06:20 +03:00
Jouni Malinen
2a0b86d319 Note set_key(WPA_ALG_NONE) failure in debug log
This makes wpa_remove_ptk() call to wpa_auth_set_key() more consistent
with all the other calls that verify the return value to keep static
analyzers happier.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-26 00:41:04 +03:00
Jouni Malinen
ff338fab92 FILS: Setup EAPOL state machines properly after FILS association (AP)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-26 00:41:04 +03:00
Jouni Malinen
da24c5aa1c FILS: Set TK after association (AP)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-26 00:41:04 +03:00
Jouni Malinen
07e0117d21 FILS: Mark connection fully authorized after FILS Association (AP)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-26 00:20:04 +03:00
Jouni Malinen
e73ffa0925 FILS: Add Association Response frame elements and encrypt them (AP)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-25 20:42:52 +03:00
Jouni Malinen
78815f3dde FILS: Decrypt Association Request elements and check Key-Auth (AP)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-25 20:42:52 +03:00
Jouni Malinen
c4fd6d8aa8 FILS: Process FILS Authentication frame (AP)
This implements processing of FILS Authentication frame for FILS shared
key authentication with ERP and PMKSA caching.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-22 23:27:01 +03:00
Jouni Malinen
ffb62f2272 FILS: Add a helper function for status code conversion
This will allow the existing code to be reused for FILS needs.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-22 23:27:01 +03:00
Jouni Malinen
c1bd4bac5f FILS: Extend wpa_auth_pmksa_get() to support PMKID matching
This is needed for FILS processing to enable PMKSA caching.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-22 23:13:17 +03:00
Jouni Malinen
c30bd28b14 FILS: Export IEEE 802.1X helper functions
ieee802_1x_encapsulate_radius() and ieee802_1x_alloc_eapol_sm() need to
be called from FILS processing.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-22 23:13:17 +03:00
Jouni Malinen
a6228b8ed6 ERP: Update client identity based on EAP-Initiate/Re-auth
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-22 23:13:17 +03:00
Jouni Malinen
2aa1e48a45 FILS: Do not clear PTK on FILS Auth/Assoc (AP)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-22 18:11:14 +03:00
Jouni Malinen
2449791b8e FILS: Update EAPOL-Key Descriptor Version RX rules (AP)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-10 21:11:47 +03:00
Jouni Malinen
75c8563e05 FILS: Perform AEAD processing after PTK has been confirmed
This covers EAPOL-Key frames other than 2/4 that needed special handling
to confirm PTK.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-10 21:11:47 +03:00
Jouni Malinen
b729fd8df9 FILS: Use AEAD cipher to protect EAPOL-Key frames (AP)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-10 21:11:47 +03:00
Jouni Malinen
3b5b7aa8fb FILS: Use AEAD cipher to check received EAPOL-Key frames (AP)
This changes 4-way handshake authenticator processing to decrypt the
EAPOL-Key frames using an AEAD cipher (AES-SIV with FILS AKMs) before
processing the Key Data field. This replaces Key MIC validation for the
cases where AEAD cipher is used. This needs to move the EAPOL-Key msg
2/4 RSN element processing to happen only after the PTK has been derived
and validated. That is done for all AKMs to avoid extra complexity with
having to maintain two code paths for this.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-10 21:11:47 +03:00
Jouni Malinen
b986648389 FILS: Update EAPOL-Key RX rules for FILS (AP)
Key Descriptor Version 0 is used with FILS and Key Info MIC field is set
to 0 with AEAD ciphers.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-10 21:11:47 +03:00
Jouni Malinen
36a50fd4e8 FILS: Set EAPOL-Key Key Descriptor Version to 0 with FILS AKMs (AP)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-10 21:11:46 +03:00
Jouni Malinen
dc5bad48af RSN authenticator: Add more debug print details on EAPOL-Key RX
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-10 21:11:46 +03:00
Jouni Malinen
6d014ffc6e Make struct wpa_eapol_key easier to use with variable length MIC
Suite B 192-bit addition from IEEE Std 802.11ac-2013 replaced the
previous fixed length Key MIC field with a variable length field. That
change was addressed with an addition of a new struct defined for the
second MIC length. This is not really scalable and with FILS coming up
with a zero-length MIC case for AEAD, a more thorough change to support
variable length MIC is needed.

Remove the Key MIC and Key Data Length fields from the struct
wpa_eapol_key and find their location based on the MIC length
information (which is determined by the AKMP). This change allows the
separate struct wpa_eapol_key_192 to be removed since struct
wpa_eapol_key will now include only the fixed length fields that are
shared with all EAPOL-Key cases in IEEE Std 802.11.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-10 21:11:46 +03:00
Jouni Malinen
94f66e8a26 FILS: Advertise ERP domain in FILS Indication element
Calculate the hashed realm from hostapd erp_domain configuration
parameter and add this to the FILS Indication element when ERP is
enabled.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-10 21:11:46 +03:00
Jouni Malinen
c30ed45f45 FILS: Allow hostapd to select FILS AKM for connection
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-10 21:11:46 +03:00
Jouni Malinen
f55acd909e FILS: Set FILS Capability bit in management frames from AP
If FILS is enabled, indicate that in Beacon, Probe Response, and
(Re)Association Response frames in the Extended Capabilities element.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-10 21:11:46 +03:00
Jouni Malinen
198a942c83 FILS: Add FILS Indication element to Beacon and Probe Response frames
If FILS is enabled, indicate that in AP Beacon/Probe Response frames.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-10 21:11:46 +03:00
Jouni Malinen
903ecbe8da FILS: Add hostapd configuration options
This adds CONFIG_FILS=y build configuration option and new key
management options for FILS authentication.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-10 21:11:27 +03:00
Jouni Malinen
94318a0d30 FILS: Add AKM definitions
This adds definitions for the new AKM suite values from P802.11ai/D11.0.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-10 20:46:36 +03:00
Michael Braun
96590564d6 FT: Allow PMK-R0 and PMK-R1 for FT-PSK to be generated locally
Station should be able to connect initially without ft_pmk_cache filled,
so the target AP has the PSK available and thus the same information as
the origin AP. Therefore neither caching nor communication between the
APs with respect to PMK-R0 or PMK-R1 or VLANs is required if the target
AP derives the required PMKs locally.

This patch introduces the generation of the required PMKs locally for
FT-PSK. Additionally, PMK-R0 is not stored (and thus pushed) for FT-PSK.

So for FT-PSK networks, no configuration of inter-AP communication is
needed anymore when using ft_psk_generate_local=1 configuration. The
default behavior (ft_psk_generate_local=0) remains to use the pull/push
protocol.

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2016-10-09 11:57:56 +03:00
Nishant Chaprana
746e5c2565 Fix spelling mistakes in number of comments
Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
2016-09-30 22:45:03 +03:00
vamsi krishna
64c92c0757 MBO: Do not parse reason_detail in non_pref_chan attr (AP)
The reason detail field was removed from non_pref_chan attr in MBO
v0.0_r25 draft. Don't parse for this element to be compliant with the
latest drafr.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-09-25 17:31:26 +03:00
Denton Gentry
442819406c taxonomy: Store Probe Request frames in hostapd_sta_info
A weakness in the initial client taxonomy mechanism is from storing both
the Probe and Associate in struct sta_info. struct sta_info is created
after a client associates (or starts authentication frame exchange),
which means that any Probe Request frames sent prior to association are
not retained. The Associate Request frame has to be seen, and then
another Probe Request frame after association, before we have a
signature for the client.

Most clients send lots of Probe Request frames (lots and lots and lots
of Probes, actually), but a few do not. ChromeOS is notably sparing in
sending Probe Request frames, it can take a long time before a signature
for a ChromeOS device is available.

Store the most recent Probe Request frame in struct hostapd_sta_info
tracking list. When a struct sta_info is created, move the Probe Request
frame information from struct hostapd_sta_info to struct sta_info.

Signed-off-by: dgentry@google.com (Denton Gentry)
Signed-off-by: denny@geekhold.com (Denton Gentry)
Signed-off-by: rofrankel@google.com (Richard Frankel)
Signed-off-by: richard@frankel.tv (Richard Frankel)
2016-09-22 00:45:24 +03:00