Commit graph

2474 commits

Author SHA1 Message Date
Jouni Malinen
9a1136b7f1 FILS: Fix RSN info in FD frame for no-group-addressed
The value from the initial RSN_CIPHER_SUITE_NO_GROUP_ADDRESSED check
ended up getting overridden with the following if. This was supposed to
be a single if statement to avoid that.

Fixes: 9c02a0f5a6 ("FILS: Add generation of FILS Discovery frame template")
Signed-off-by: Jouni Malinen <j@w1.fi>
2021-02-28 11:27:42 +02:00
Jouni Malinen
a826ff2d95 Ignore group-addressed SA Query frames
These frames are used for verifying that a specific SA and protected
link is in functional state between two devices. The IEEE 802.11
standard defines only a case that uses individual MAC address as the
destination. While there is no explicit rule on the receiver to ignore
other cases, it seems safer to make sure group-addressed frames do not
end up resulting in undesired behavior. As such, drop such frames
instead of interpreting them as valid SA Query Request/Response.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2021-02-27 20:27:00 +02:00
Ben Greear
827b43b3ca RADIUS client: Support SO_BINDTODEVICE
Allow the RADIUS client socket to be bound to a specific netdev. This
helps hostapd work better in VRF and other fancy network environments.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Andreas Tobler <andreas.tobler at onway.ch>
2021-02-27 10:51:15 +02:00
Sunil Dutt
3a05f89edc Android: Add DRIVER command support on hostapd and hostapd_cli
Add DRIVER command support on hostapd and hostapd_cli on Android
similarly to the way this previously enabled in wpa_supplicant and
wpa_cli.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2021-02-26 20:22:41 +02:00
Jouni Malinen
dc72854fe2 Fix handle_auth_cb() message length check regression
Reordering of code in handle_auth_cb() when adding support for full
station state messaged up frame length checks. The length was originally
tested before looking at the payload of the frame and that is obviously
the correct location for that check. The location after those full state
state changes was after having read six octets of the payload which did
not help at all since there was no addition accesses to the payload
after that check.

Move the payload length check to appropriate place to get this extra
level of protection behaving in the expected manner. Since this is a TX
status callback handler, the frame payload is from a locally generated
Authentication frame and as such, it will be long enough to include
these fields in production use cases. Anyway, better keep this check in
working condition.

Fixes: bb598c3bdd ("AP: Add support for full station state")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2021-02-23 00:30:09 +02:00
Ilan Peer
6c7b0a9657 PASN: Correctly set RSNXE bits from AP
The capability bit index should not be shifted here as the shifting is
handled later below when building the RSNXE octets.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2021-02-20 00:26:21 +02:00
Veerendranath Jakkam
6f92f81dac AP: Check driver's capability to enable OCV when driver SME is used
When the driver SME is used, offloaded handshakes which need Operating
Channel Validation (OCV) such as SA Query procedure, etc. would fail if
hostapd enables OCV based on configuration but the driver doesn't
support OCV. To avoid this when driver SME is used, enable OCV from
hostapd only when the driver indicates support for OCV.

This commit also adds a capability flag to indicate whether driver SME
is used in AP mode.

Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
2021-02-16 00:47:43 +02:00
Veerendranath Jakkam
d36d4209fd Enable beacon protection only when driver indicates support
Enabling beacon protection will cause STA connection/AP setup failures
if the driver doesn't support beacon protection. To avoid this, check
the driver capability before enabling beacon protection.

This commit also adds a capability flag to indicate beacon protection
support in client mode only.

Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
2021-02-16 00:47:43 +02:00
Jouni Malinen
b1c23d3f25 HE: Fall back to 20 MHz on 2.4 GHz if 40 MHz is not supported
At least the ACS case of an attempt to pick a 40 MHz channel on the 2.4
GHz band could fail if HE was enabled and the driver did not include
support for 40 MHz channel bandwidth on the 2.4 GHz band in HE
capabilities. This resulted in "40 MHz channel width is not supported in
2.4 GHz" message when trying to configure the channel and failure to
start the AP.

Avoid this by automatically falling back to using 20 MHz bandwidth as
part of channel parameter determination at the end of the ACS procedure.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2021-02-15 18:27:10 +02:00
Aloka Dixit
f1c6c9d3eb ACS: Allow downgrading to 20 MHz based on OBSS results
When auto channel selection (ACS) is used for HE 40 MHz in the 2.4 GHz
band, AP sets center frequency after finding a 40 MHz channel and then
runs a scan for overlapping BSSes in neighboring channels. Upon OBSS
detection, AP should downgrade to 20 MHz bandwidth.

This was broken because allowed_ht40_channel_pair() returns true in this
case and the steps to reset center frequency are not executed causing
failure to bring interface up.

Fix the condition to allow rollback to 20 MHz.

Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
2021-02-15 18:16:33 +02:00
Aloka Dixit
024b4b2a29 AP: Unsolicited broadcast Probe Response configuration
Add hostapd configuration options for unsolicited broadcast
Probe Response transmission for in-band discovery in 6 GHz.
Maximum allowed packet interval is 20 TUs (IEEE P802.11ax/D8.0
26.17.2.3.2, AP behavior for fast passive scanning).
Setting value to 0 disables the transmission.

Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
2021-02-14 23:04:26 +02:00
Jouni Malinen
6b59e63f0e Include secondary channel config in no-hw-channel-found message
This makes the error message easier to understand if the AP mode setup
failure is caused by invalid secondary channel configuration while the
primary channel is valid.

Signed-off-by: Jouni Malinen <j@w1.fi>
2021-02-14 19:31:14 +02:00
Aloka Dixit
9c02a0f5a6 FILS: Add generation of FILS Discovery frame template
Add hostapd configuration parameters for FILS Discovery frame
transmission interval and prepare a template for FILS Discovery frame
for the driver interface. The actual driver interface changes are not
included in this commit.

Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
2021-02-14 18:03:49 +02:00
Jouni Malinen
c4c529e9cb Add a helper function for determining RSN capabilities field value
This information is needed in more than one place, so add a helper
function to avoid need to duplicate this code.

Signed-off-by: Jouni Malinen <j@w1.fi>
2021-02-14 18:03:38 +02:00
Jouni Malinen
3eb5f7128e Do not include VHT elements in Beacon frames on the 6 GHz band
A similar change was previously done for Probe Response frames, but the
Beacon frame case was missed. Fix this to remove the VHT elements also
from Beacon frames on the 6 GHz since the relevant information is
included only in the HE elements on that band.

Fixes: 49e95ee1ee ("AP: Publish only HE capabilities and operation IEs on 6 GHz band")
Signed-off-by: Jouni Malinen <j@w1.fi>
2021-02-14 00:33:08 +02:00
Shay Bar
2c2b6d265b Add Transmit Power Envelope also for 6 GHz HE AP
According to IEEE P802.11ax/D8.0, add Transmit Power Envelope element
into Beacon and Probe Response frames when operating HE AP on the 6 GHz
band.

Signed-off-by: Shay Bar <shay.bar@celeno.com>
2021-02-14 00:29:31 +02:00
Shay Bar
6c2b729de0 Use hostapd_get_oper_chwidth() when build Transmit Power Envelope element
hostapd_get_oper_chwidth(iconf) instead of direct access to
iface->conf->vht_oper_chwidth is needed here to be able to use this with
HE in cases where VHT is not enabled.

Signed-off-by: Shay Bar <shay.bar@celeno.com>
2021-02-14 00:24:53 +02:00
Shay Bar
5d3c4496fb Make VHT Transmit Power Envelope element helper more generic
According to latest IEEE 802.11 standard, Transmit Power Envelope
element is also relevant to IEEE 802.11ax and is no longer called VHT
Transmit Power Envelope. Remove the VHT naming from the element and move
hostapd_eid_txpower_envelope() from ieee802_11_vht.c to ieee802_11.c in
preparation of using it with HE.

Signed-off-by: Shay Bar <shay.bar@celeno.com>
2021-02-14 00:22:52 +02:00
Jouni Malinen
ad59639ed8 DPP2: Fix Authentication Request destination in the chirping case
The Authentication Request frames triggered by the reception of a
Presence Announcement frame were sent to the broadcast address. This is
not correct behavior since the source MAC address of the Presence
Announcement frame was supposed to override the Responder MAC address.
Fix this by using that source MAC address to avoid unnecessary use of
broadcast frames.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2021-02-09 20:41:08 +02:00
Aloka Dixit
598f671321 SAE: Avoid driver STA entry removal unnecessarily when using H2E/PK
The new status code values for SAE H2E and PK resulted in the
sta->added_unassoc cases incorrectly removing the STA entry after
successful SAE commit messages. Fix this by using sae_status_success()
instead of direct check for WLAN_STATUS_SUCCESS when processing SAE
commit messages before removing station entry.

Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
2021-02-08 23:56:59 +02:00
Ilan Peer
99cd453720 hw_feature: Correctly select mode in case of the 6 GHz band
There are 2 HW modes with IEEE80211_MODE_A: one for the 5 GHz channels
and one for 6 GHz channels. Since hw_get_chan() checks all the
compatible hw modes, eventually, an incorrect hw mode is selected.

To fix this, add a function that checks if a specific mode supports
the requested frequency and if so use it as the current mode.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2021-02-08 00:54:10 +02:00
Rajkumar Manoharan
f728c867e3 AP: Extend Spatial Reuse Parameter Set
Extend SPR element to support following fields and pass all
information to kernel for driver use.
 * Non-SRG OBSS PD Max Offset
 * SRG BSS Color Bitmap
 * SRG Partial BSSID Bitmap

Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
2021-02-08 00:41:52 +02:00
Rajkumar Manoharan
c3d557b4df hostapd: Add HE 6 GHz band capability configuration
Enable user to configure Maximum MPDU Length, Maximum A-MPDU Length
Exponent, Rx Antenna Pattern Consistency, and Tx Antenna Pattern
Consistency of 6 GHz capability through config file.

Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
2021-02-08 00:09:45 +02:00
Janusz Dziedzic
ef26fc19fa DFS: Allow switch to an available channel
For EU, where preCAC is allowed, we should allow switch to DFS available
channels, instead of restarting BSS.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
2021-02-07 10:30:09 +02:00
Raphaël Mélotte
f95ccc102a WPS: Reconfigure credentials on hostapd config reload
When new credentials are configured and hostapd is reconfigured using
SIGHUP (or RELOAD on the ctrl_iface), also update the WPS credentials.

Before these changes, when WPS is triggered the Registar always serves
the credentials that were configured when hostapd started.

Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
2021-02-06 17:15:31 +02:00
Raphaël Mélotte
2fd90eb095 WPS: Use helper variables to clean up code
This is in preparation of larger changes in hostapd_update_wps() to keep
the commits more readable.

Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
2021-02-06 17:12:24 +02:00
Michal Kazior
3a00a86bb9 hostapd: Fix dpp_listen in DPP responder scenario
Some time ago it was found some drivers are setting their hw/ucode RX
filters restrictively enough to prevent broadcast DPP Action frames from
being received at upper layers in the stack.

A set of patches was introduced to the kernel and
ath9k driver as well as wpa_supplicant, e.g.,

  a39e9af90 ("nl80211: DPP listen mode callback")
  4d2ec436e ("DPP: Add driver operation for enabling/disabling listen mode")

However, the hostapd code itself was not calling the new multicast
registration. As such the AP side of things wasn't working as expected
in some scenarios. I've found this while trying to get ath9k working as
an AP Responder/Configurator.

The problem wasn't seen on, e.g., mac80211 hwsim driver.

Extend the wpa_supplicant mechanism to work with hostapd as well.

Signed-off-by: Michal Kazior <michal@plume.com>
2021-02-06 16:06:15 +02:00
Raphaël Mélotte
4a7e0ac268 hostapd: Add an option to notify management frames on ctrl_iface
In some contexts (e.g., Multi-AP) it can be useful to have access to
some of the management frames in upper layers (e.g., to be able to
process the content of association requests externally).

Add 'notify_mgmt_frames'. When enabled, it will notify the ctrl_iface
when a management frame arrives using the AP-MGMT-FRAME-RECEIVED event
message.

Note that to avoid completely flooding the ctrl_iface, not all
management frames are included (e.g., Beacon and Probe Request frames
are excluded).

Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
2021-02-06 13:56:18 +02:00
Andrei Otcheretianski
fa859ebb19 RSN+WPA: Fix RSNE removing in EAPOL-Key msg 3/4 when RSNXE is included
When the AP advertised RSNE, RSNXE, and WPA IE, hostapd incorrectly
removed the RSNE in the EAPOL-Key msg 3/4 if the STA associates with
WPA, leaving only RSNXE instead of WPA IE. WPA STA fails to connect to
such AP as the WPA IE is missing.

Since RSNXE is not really used in non-RSN connection, just remove it
here with RSNE.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2021-02-06 12:09:30 +02:00
Shay Bar
a287c20789 Disable HE capabilities when using unacceptable security config
Add HE configuration check similar to HT/VHT.

Signed-off-by: Shay Bar <shay.bar@celeno.com>
2021-02-06 11:41:09 +02:00
Muna Sinada
2acfd15a2a hostapd: Generalize channel switch methods to incorperated HE mode
Remove the VHT specific naming on methods that are utilized in both VHT
and HE modes.

Signed-off-by: Muna Sinada <msinada@codeaurora.org>
2021-02-06 11:41:09 +02:00
Muna Sinada
2908dc91c1 hostapd: Enable HE for channel switch commmand
Add HE as an accepted option ("he") in the CHAN_SWITCH command similarly
to the way VHT is addressed.

Signed-off-by: Muna Sinada <msinada@codeaurora.org>
2021-02-06 11:41:09 +02:00
Aloka Dixit
630b1fdba8 AP: Add 6 GHz security constraints
Add security constraints for the 6 GHz band as given in IEEE
P802.11ax/D8.0, 12.12.2.

Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
2021-02-02 23:39:31 +02:00
Ilan Peer
24f0507af4 WPA: Support deriving KDK based on capabilities (Authenticator)
Derive the KDK as part of PMK to PTK derivation if forced by
configuration or in case both the local AP and the peer station declare
support for secure LTF.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2021-01-26 23:09:39 +02:00
Ilan Peer
9e7b980d65 PASN: Include RSNXE in the PASN negotiation
IEEE P802.11az/D2.6 added definitions to include RSNXE in the PASN
negotiation. Implement the new functionality in both wpa_supplicant and
hostapd.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2021-01-26 23:09:36 +02:00
Ilan Peer
d8cd20e37b RSN: Add RSNXE new definitions
IEEE P802.11az/D2.6 defines the following additional capabilities to
RSNXE:

- Secure LTF support
- Secure RTT support
- Protection of range negotiation and measurement management frames.

Add support for advertising the new capabilities.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2021-01-26 23:08:27 +02:00
Ilan Peer
2eb2fb8bd4 AP: Support PASN with FT key derivation
Note that the implementation is not complete as it is missing support
for the FT wrapped data which is optional for the station, but must be
supported by the AP in case the station included it.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2021-01-26 17:49:00 +02:00
Ilan Peer
62edb79a0c AP: Support PASN with FILS key derivation
As the PASN FILS authentication is only defined for FILS SK without PFS,
and to support PASN authentication with FILS, implement the PASN with
FILS processing as part of the PASN handling and not as part of the WPA
Authenticator state machine.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2021-01-25 20:28:33 +02:00
Ilan Peer
da35e1214d AP: Support PASN with SAE key derivation
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2021-01-25 20:27:14 +02:00
Ilan Peer
3040c8a2da AP: Add support for PASN processing to the SME
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2021-01-25 20:27:12 +02:00
Ilan Peer
f2f8e4f458 Add PTKSA cache to hostapd
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2021-01-25 19:15:47 +02:00
Ilan Peer
2c963a117a AP: Add support for configuring PASN
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2021-01-25 19:15:47 +02:00
Ilan Peer
d87f4aea11 FILS: Extend the fils_pmk_to_ptk() function to also derive KDK
Extend the fils_pmk_to_ptk() to also derive Key Derivation
Key (KDK) which can later be used for secure LTF measurements.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2021-01-25 18:36:40 +02:00
Ilan Peer
6e834db74e FT: Extend the wpa_pmk_r1_to_ptk() function to also derive KDK
Extend the wpa_pmk_r1_to_ptk() to also derive Key Derivation
Key (KDK), which can later be used for secure LTF measurements.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2021-01-25 18:36:40 +02:00
Ilan Peer
46c232eb76 WPA: Extend the wpa_pmk_to_ptk() function to also derive KDK
Extend the wpa_pmk_to_ptk() to also derive Key Derivation
Key (KDK), which can later be used for secure LTF measurements.

Update the wpa_supplicant and hostapd configuration and the
corresponding WPA and WPA Auth state machine, to allow enabling of KDK
derivation. For now, use a testing parameter to control whether KDK is
derived.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2021-01-25 18:36:40 +02:00
Sreeramya Soratkal
833cdbe97d Add support for new 5 GHz channels 173 and 177
Add support for new channels 173 and 177 in the operating classes 125 to
130 as defined in draft IEEE P802.11ax/D8.0.

Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
2021-01-22 19:18:10 +02:00
Purushottam Kushwaha
959af4f576 DPP: Abort authentication if no Auth Confirm is received within a second
After sending DPP Auth Response, the Responder might not receive the
Auth Confirm either due to the Initiator not sending it or the reception
of the frame failing for some reason (e.g., Responder having already
left the negotiation channel). If this happens, following initiation
attempts would fail since the consecutive Auth Request would get
discarded since the previous authentication is still in progress.

Terminate DPP authentication on Responder, if no Auth Confirm is
received within one second of successfully sending Auth Response. This
allows the Responder to accept start of a new exchange.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2021-01-22 19:18:10 +02:00
Veerendranath Jakkam
7131fede34 Extend the setband support for 6 GHz and band combinations
Support possible band combinations of 2.4 GHz, 5 GHz, and 6 GHz with
QCA_WLAN_VENDOR_ATTR_SETBAND_MASK attribute. Ensure backwards
compatibility with old drivers that are using
QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE attribute and supporting only 2.4 GHz
and 5 GHz bands.

Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
2020-12-11 19:56:14 +02:00
John Crispin
d83eaa351e Add option to ignore Probe Request frames when RSSI is too low
Add a new hostapd configuration parameters rssi_ignore_probe_request to
ignore Probe Request frames received with too low RSSI.

Signed-off-by: John Crispin <john@phrozen.org>
2020-12-02 17:14:39 +02:00
David Bauer
4683b72183 DFS: Enter DFS state if no available channel is found
Previously hostapd would not stop transmitting when a DFS event was
detected and no available channel to switch to was available.

Disable and re-enable the interface to enter DFS state. This way, TX
does not happen until the kernel notifies hostapd about the NOP
expiring.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-12-02 16:49:29 +02:00
Shay Bar
eee0d242bb hostapd: Add ability to disable HT/VHT/HE per BSS
Add the ability to disable HT/VHT/HE for specific BSS from hostapd.conf.

- Add disable_11ax boolean to hostapd_bss_config.
- Change disable_11n and disable_11ac to bool in hostapd_bss_config.
- Add configuration option to set these disable_11* parameters
  (which were previously used only automatically based on incompatible
  security parameters to disable HT/VHT).

Signed-off-by: Shay Bar <shay.bar@celeno.com>
2020-12-02 13:41:18 +02:00
Markus Theil
7c2cad969a mesh: Fix DFS deinit/init
The hostapd DFS code deinitializes and initializes the AP interface, if
a clean channel switch is not possible. In this case the AP code paths
would deinit the driver, for example nl80211, without wpa_supplicant
code paths getting notice of this.

Therefore add callbacks for wpa_supplicant mesh methods, which are
called on init/deinit of the AP BSS. These callbacks are then used to
handle the reset in the mesh code.

Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
2020-12-01 00:31:56 +02:00
Peter Oh
f1df4fbfc7 mesh: Use setup completion callback to complete mesh join
Mesh join function is the last function to be called during mesh join
process, but it's been called a bit earlier than it's supposed to be, so
that some mesh parameter values such as VHT capabilities were not
applied correct when mesh join is in process. Moreover, the current
design of mesh join that is called directly after mesh initialization
isn't suitable for DFS channels to use, since mesh join process should
be paused until DFS CAC is done and resumed after it's done.

The callback will be called by hostapd_setup_interface_complete_sync().
There is a possibility that completing mesh init fails, so add error
handling codes for that.

Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
2020-11-30 11:57:37 +02:00
Rohan Dutta
fdf114641f nl80211: Send the sae_pwe value to the driver
Use NL80211_ATTR_SAE_PWE attribute to indicate the sae_pwe value
to the driver during the NL80211_CMD_START_AP and NL80211_CMD_CONNECT
in WPA3-Personal networks which are using SAE authentication.

Signed-off-by: Rohan Dutta <drohan@codeaurora.org>
2020-11-16 15:50:44 +02:00
Vinita S. Maloo
c2c4686228 Set NLA_F_NESTED flag with NL80211_ATTR_VENDOR_DATA conditionally
The newer kernel versions enforce strict netlink attribute policy
validation and will cause cfg80211 to reject vendor commands with
NL80211_ATTR_VENDOR_DATA if NLA_F_NESTED attribute is not set but
if the vendor command is expecting nested data within
NL80211_ATTR_VENDOR_DATA attribute.

Most of the earlier instances were addressed by adding NLA_F_NESTED
flag in nla_nest_start(). This commit addresses the remaining
instance in which NL80211_ATTR_VENDOR_DATA is populated using data
set by user through the control interface.

Enhance the control interface VENDOR command to indicate whether the
vendor subcommand uses nested attributes within NL80211_ATTR_VENDOR_DATA
attribute or not.

Set NLA_F_NESTED flag for existing QCA vendor commands which use nested
attributes within the NL80211_ATTR_VENDOR_DATA attributes so that the
old frameworks implementations for already existing commands work
without any issues.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-11-10 23:48:00 +02:00
Jouni Malinen
a9fed5f5b5 Avoid undefined behavior with memcpy PMK/PSK update
When SAE is used, the local pointer pmk may point to sm->PMK. Skip the
memcpy operation in such a case since it is not really needed and use of
overlapping memory buffers is undefined behavior for memcpy().

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-11-02 18:46:35 +02:00
Jouni Malinen
183e72ae13 SAE-PK: Do not accept SAE-PK status code when no PK is configured
Make sae_status_success() more explicit by rejecting SAE-PK status code
when the AP is not configured with PK.

Fixes: 20ccf97b3d ("SAE-PK: AP functionality")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-10-20 00:37:01 +03:00
Markus Theil
c3f37c35f0 DFS: Use helper functions for VHT/HE parameters
This is needed to cover the HE-specific conf->he_oper_chwidth value in
addition to conf->vht_oper_chwidth.

Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
2020-10-14 13:05:11 +03:00
Markus Theil
7f8ac02e85 HE/VHT: Fix frequency setup with HE enabled
Some places in the code base were not using the wrappers like
hostapd_set_oper_centr_freq_seg0_idx and friends. This could lead to
errors, for example when joining 80 MHz mesh networks. Fix this, by
enforcing usage of these wrappers.

wpa_supplicant_conf_ap_ht() now checks for HE capability before dealing
with VHT in order for these wrappers to work, as they first check HE
support in the config.

While doing these changes, I've noticed that the extra channel setup
code for mesh networks in wpa_supplicant/mesh.c should not be necessary
anymore and dropped it. wpa_supplicant_conf_ap_ht() should handle this
setup already.

Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
2020-10-14 12:44:09 +03:00
Johannes Berg
1d0d8888af build: Make more library things common
We don't really need to duplicate more of this, so just
move the lib.rules include to the end and do more of the
stuff that's common anyway there.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-10-12 20:20:35 +03:00
Johannes Berg
f4b3d14e97 build: Make a common library build
Derive the library name from the directory name, and let each
library Makefile only declare the objects that are needed.

This reduces duplicate code for the ar call. While at it, also
pretty-print that call.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-10-12 20:20:20 +03:00
Johannes Berg
87098d3324 build: Put archive files into build/ folder too
This is something I hadn't previously done, but there are
cases where it's needed, e.g., building 'wlantest' and then
one of the tests/fuzzing/*/ projects, they use a different
configuration (fuzzing vs. not fuzzing).

Perhaps more importantly, this gets rid of the last thing
that was dumped into the source directories, apart from
the binaries themselves.

Note that due to the use of thin archives, this required
building with absolute paths.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-10-11 11:16:00 +03:00
Johannes Berg
722138cd25 build: Put object files into build/ folder
Instead of building in the source tree, put most object
files into the build/ folder at the root, and put each
thing that's being built into a separate folder.

This then allows us to build hostapd and wpa_supplicant
(or other combinations) without "make clean" inbetween.

For the tests keep the objects in place for now (and to
do that, add the build rule) so that we don't have to
rewrite all of that with $(call BUILDOBJS,...) which is
just noise there.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-10-10 12:51:39 +03:00
Johannes Berg
06a6adb54e build: Use build.rules in lib.rules
Use the new build.rules in lib.rules and also unify the
clean targets to lib.rules.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-10-10 12:47:41 +03:00
Thomas Pedersen
a28d127b1a AP: Reflect status code in SAE reflection attack test
When testing SAE reflection, the incoming commit may have the H2E status
code (126) or SAE-PK (127), but the test code in the AP was always
sending back status code 0. The STA would then reject the commit
response due to expecting H2E/SAE-PK status code.

Just reflect the incoming status code so the commit can be rejected
based on the SAE contents regardless of which variant of SAE was used.

Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
2020-10-09 16:50:36 +03:00
Veerendranath Jakkam
debf3e2165 OCV: Work around for misbehaving STAs that indicate OCVC=1 without OCI
Some legacy stations copy previously reserved RSN capability bits,
including OCVC, in (Re)Association Request frames from the AP's RSNE but
do not indicate MFP capability and/or do not send OCI in RSN handshakes.
This is causing connection failures with such erroneous STAs.

To improve interoperability with such legacy STAs allow a workaround OCV
mode to be enabled to ignore OCVC=1 from the STA if it does not follow
OCV requirements in the first protected exchange. This covers cases
where a STA claims to have OCV capability, but it does not negotiate use
of management frame protection or does not include OCI in EAPOL Key msg
2/4, FT Reassociation Request frame, or FILS (Re)Association Reqest.

The previous behavior with ocv=1 is maintained, i.e., misbehaving STAs
are not allowed to connect. When the new workaround mode is enabled with
ocv=2, the AP considers STA as OCV capable on below criteria
- STA indicates both OCV and MFP capability
- STA sends OCI during connection attempt in a protected frame

Enabling this workaround mode reduced OCV protection to some extend
since it allows misbehavior to go through. As such, this should be
enabled only if interoperability with misbehaving STAs is needed.

Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
2020-10-08 18:46:38 +03:00
Shaakir Mohamed
d48a3a6768 FT: Modify status code in FT Reassoc frame for invalid OCI channel info
Modify status code in FT Reassociation Response frame from
WLAN_STATUS_UNSPECIFIED_FAILURE to WLAN_STATUS_INVALID_FTE when replying
to an invalid OCI channel info (subelement of FTE) in FT Reassociation
Request frame.

Signed-off-by: Shaakir Mohamed <smohamed@codeaurora.org>
2020-10-08 00:20:10 +03:00
Andrew Beltrano
980c4da413 DPP2: Presence Announcement notification in AP
Generate a control interface event upon receipt of DPP Presence
Announcement frames. This allows external programs to instrument hostapd
with bootstrapping information on-demand.

Signed-off-by: Andrew Beltrano <anbeltra@microsoft.com>
2020-10-07 21:20:18 +03:00
Andrew Beltrano
cf3d260c39 DPP2: Fix hostapd crash setting global configurator params on chirp RX
When a Presence Announcement frame is received, a check is done to
ensure an ongoing auth is not in progress (!hapd->dpp_auth). A new DPP
auth is then initialized, however, when setting global configurator
params for it, the hapd->dpp_auth pointer is used which was earlier
confirmed as NULL, causing a crash in dpp_set_configurator params when
the pointer is dereferenced.

This only occurs when there are global DPP configurator params to be set
and the peer has no overriding configurator params. If no global DPP
configurator params exist, the call to dpp_set_configurator exits early
and the problem is not observed.

Fix by using the newly init'ed DPP auth structure for setting global
DPP configurator params.

Signed-off-by: Andrew Beltrano <anbeltra@microsoft.com>
2020-10-07 20:57:36 +03:00
Disha Das
5c6c0d569a DPP: Fix GAS fragmentation for DPP Config Response from hostapd
The Query Response Length field was missing from GAS Initial Response
and GAS Comeback Response frames in the DPP specific code path from
hostaps GAS server. This resulted in invalid frames being used when the
DPP Config Response needed fragmentation. Fix this by adding the Query
Response Length fields into these frames.

Signed-off-by: Disha Das <dishad@codeaurora.org>
2020-10-06 23:34:41 +03:00
Disha Das
a7f55f7f68 WPS: Enable SA Query checks for WPS AP
Initiate SA Query for a WPS+MFP AP. STA flag checks for MFP added for
Association Request frames that use WPS IE without RSNE. This is needed
to avoid giving an opportunity to skip the protection against
disconnections when WPS is enabled.

Signed-off-by: Disha Das <dishad@codeaurora.org>
2020-10-06 22:44:43 +03:00
Jouni Malinen
cab139ebc2 Fix a typo in a comment
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-09-22 23:31:20 +03:00
Karthikeyan Kathirvel
7e20502f7a hostapd: Resolved compiler uninitialized warning
Resolved the below warning
../src/ap/ieee802_11.c:4535:25: warning: 'reply_res' may be used
uninitialized in this function [-Wmaybe-uninitialized]
  if (sta && ((reply_res != WLAN_STATUS_SUCCESS &&
		                           ^
Since reply_res is been assigned inside an if condition and so
compiler treats reply_res as uninitalized variable

Initialize reply_res with WLAN_STATUS_UNSPECIFIED_FAILURE.

Fixes: 5344af7d22 ("FT: Discard ReassocReq with mismatching RSNXE Used value")
Signed-off-by: Karthikeyan Kathirvel <kathirve@codeaurora.org>
2020-09-22 23:29:18 +03:00
Rohan
e3ba0c4cd2 Do not start SA Query procedure without keys
The AP mode condition for initiating the SA Query procedure when
receiving a new (Re)Association Request frame used only association
state and MFP negotiation result without checking that the key exchange
has been completed. This can give rise to a corner case where the SA
Query procedure may get started after open association but before the
4-way handshake has been completed, resulting in open SA query frames
over the air.

Fix this by adding station authorized check in hostapd_notif_assoc() and
check_assoc_ies().

Signed-off-by: Rohan <drohan@codeaurora.org>
2020-09-22 23:11:30 +03:00
Shaakir Mohamed
41f8189057 SAE-PK: Add support to skip sae_pk password check for testing purposes
Add support to skip sae_pk password check under compile flag
CONFIG_TESTING_OPTIONS which allows AP to be configured with
sae_pk enabled but a password that is invalid for sae_pk.

Signed-off-by: Shaakir Mohamed <smohamed@codeaurora.org>
2020-09-11 15:45:42 +03:00
Veerendranath Jakkam
a71b100c3b OCV: Allow connecting MFP incapable OCV STA when OCV is disabled in AP
Skip check to mandate MFP capability for OCV enabled STA when OCV is
disabled in AP. This is to improve interoperability with STAs in which
OCV capability is advertised incorrectly without advertising MFP when
OCV is disabled in AP.

Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
2020-09-11 15:26:31 +03:00
Veerendranath Jakkam
5ecb45a41c OCV: Use more granular error codes for OCI validation failures
Enhance the return values of ocv_verify_tx_params with enum to indicate
different OCI verification failures to caller.

Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
2020-09-11 15:23:28 +03:00
Jouni Malinen
7ddb71224b DPP2: Support QR mutual auth scan-during-auth-exchange (hostapd)
Extend DPP authentication session search for the DPP_QR_CODE command to
cover the ongoing exchanges in Controller/Responder. This was previously
done for wpa_supplicant, but not for hostapd, so complete this support
on the hostapd side.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-08-25 16:11:43 +03:00
Jouni Malinen
4ecb6dd16b DPP2: Controller support in hostapd
Extend hostapd support for DPP Controller to cover the DPP_CONTROLLER_*
cases that were previously implemented only in wpa_supplicant. This
allows hostapd/AP to be provisioned using DPP over TCP.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-08-25 15:53:08 +03:00
Chittur Subramanian Raman
96e63008fb OWE: Do not add DH Params element in AssocResp with PMKSA caching
As per RFC 8110 (Opportunistic Wireless Encryption), if the AP has the
PMK identified by the PMKID and wishes to perform PMK caching, it will
include the PMKID in the Association Response frame RSNE but does not
include the Diffie-Hellman Parameter element.

This was already addressed for most cases with owe_process_assoc_req()
not setting sta->owe_ecdh in case PMKSA caching is used. However, it was
possible to an old STA entry to maintain the initial sta->owe_ecdh value
if reassociation back to the same AP was used to initiate the PMKSA
caching attempt. Cover that case by adding an explicit check for the
time when the Association Response frame is being generated.

Signed-off-by: Chittur Subramanian Raman <craman@maxlinear.com>
2020-08-22 13:33:10 +03:00
Jouni Malinen
c6a760b9c4 DPP: Add process_conf_obj into TCP connection data struct
This is needed to avoid issues with hostapd not having set this function
pointer in dpp_global.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-08-14 17:31:51 +03:00
Jouni Malinen
7f366fcbdc DPP: Add msg_ctx into TCP connection data struct
This is needed to avoid issues with hostapd not having set msg_ctx in
dpp_global.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-08-14 17:26:32 +03:00
Jouni Malinen
6aa7aa8089 DPP2: hostapd/AP as Enrollee/Initiator over TCP
Extend DPP support in hostapd to allow AP Enrollee role when initiating
the exchange using TCP.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-08-14 16:44:38 +03:00
Rohan
0fa274d2bf Derive seg0_idx and seg1_idx for 6 GHz when processing channel switch
The function hostapd_event_ch_switch() derived the seg0_idx and seg1_idx
values only for the 5 GHz and 2.4 GHz bands and the 6 GHz case ended up
using incorrect calculation based on the 5 GHz channel definitions.

Fix this by adding support for 6 GHz frequencies.

Signed-off-by: Rohan <drohan@codeaurora.org>
2020-08-13 21:37:49 +03:00
Jouni Malinen
c6d0e5a93d DPP2: Add E-id in Reconfig Announcement
Add an encrypted Enrollee identifier into Reconfig Announcement frames
and decrypt that on the Configurator side. The actual E-id value is
currently not used for anything, but it can be used in the future to
provide better control over reconfiguration.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-08-07 22:54:53 +03:00
Jouni Malinen
e5be6e68c8 DPP2: Add Enrollee netAccessKey group into Reconfig Announcement
This was added to the protocol design to support cases where the
C-sign-key uses a different group than the netAccessKey. The Enrollee
now indicates its netAccessKey group in Reconfig Announcement and the
Configurator builds it own reconfig Connector using that group instead
of the group used for the C-sign-key.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-08-07 15:25:10 +03:00
Jouni Malinen
7ca81190a8 SAE-PK: Allow SAE-PK style wpa_passphrase if SAE-PK is enabled with same
This prevents use of a SAE-PK style password as the WPA-PSK passphrase
only if the same password is not also enabled through sae_password for
use with SAE-PK.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-08-06 23:52:07 +03:00
Jouni Malinen
f8c756c5b8 FT: Rename temporary blocking of nonresponsive R0KH
Avoid use of the "blacklist" term here to reduce undesired connotations.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-07-24 12:25:32 +03:00
Muna Sinada
621745917f Allow HE-without-VHT to add the Channel Switch Wrapper element
Modify the check for VHT to include an option for HE in
hostapd_eid_wb_chsw_wrapper() and its callers to allow the Channel
Switch Wrapper element with the Wide Bandwidth Channel Switch subelement
to be included in Beacon and Probe Response frames when AP is operating
in HE mode without VHT.

Signed-off-by: Muna Sinada <msinada@codeaurora.org>
2020-06-11 00:56:45 +03:00
Muna Sinada
d51b1b7a66 Move hostapd_eid_wb_chsw_wrapper() to non-VHT-specific file
Move hostapd_eid_wb_chsw_wrapper() from VHT specific ieee802_11_vht.c to
ieee802_11.c since this can be used for both HE and VHT. This commit
does not change any functionality to enable the HE use case, i.e., the
function is just moved as-is.

Signed-off-by: Muna Sinada <msinada@codeaurora.org>
2020-06-11 00:53:26 +03:00
Rajkumar Manoharan
1f72bbbefb AP: Reject association request upon invalid HE capabilities
Operation in the 6 GHz band mandates valid HE capabilities element in
station negotiation. Reject association request upon receiving invalid
or missing HE elements.

Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
2020-06-10 21:34:38 +03:00
Rajkumar Manoharan
088bef1786 AP: Restrict Vendor VHT to 2.4 GHz only
Vendor VHT IE is used only on the 2.4 GHz band. Restrict the use of
vendor VHT element to 2.4 GHz. This will ensure that invalid/wrong user
configuration will not impact beacon data in other than the 2.4 GHz
band.

Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
2020-06-10 21:30:50 +03:00
Rajkumar Manoharan
6a34bd3007 HE: Use device HE capability instead of HT/VHT for 6 GHz IEs
Previously, 6 GHz Band Capability element was derived from HT and VHT
capabilities of the device. Removes such unnecessary dependency by
relying directly on the HE capability.

In addition, clean up the struct ieee80211_he_6ghz_band_cap definition
to use a 16-bit little endian field instead of two 8-bit fields to match
the definition in P802.11ax.

Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
2020-06-10 21:23:24 +03:00
Jouni Malinen
363dbf1ece SAE-PK: Remove requirement of SAE group matching SAE-PK (K_AP) group
This was clarified in the draft specification to not be a mandatory
requirement for the AP and STA to enforce, i.e., matching security level
is a recommendation for AP configuration rather than a protocol
requirement.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-06-10 12:46:49 +03:00
Subrat Dash
411e42673f Move local TX queue parameter parser into a common file
This allows the same implementation to be used for wpa_supplicant as
well.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-06-09 00:17:39 +03:00
Jouni Malinen
4ff0df39eb SAE-PK: Testing functionality to allow behavior overrides
The new sae_commit_status and sae_pk_omit configuration parameters and
an extra key at the end of sae_password pk argument can be used to
override SAE-PK behavior for testing purposes.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-06-08 15:21:18 +03:00
Jouni Malinen
0c4ffce464 Allow transition_disable updates during the lifetime of a BSS
This is mainly for testing purposes to allow more convenient checking of
station behavior when a transition mode is disabled.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-06-07 17:06:52 +03:00
Jouni Malinen
cc22fb1b86 SAE: Move H2E and PK flags to main sae_data
This maintains knowledge of whether H2E or PK was used as part of the
SAE authentication beyond the removal of temporary state needed during
that authentication. This makes it easier to use information about which
kind of SAE authentication was used at higher layer functionality.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-06-06 15:18:13 +03:00
Jouni Malinen
20ccf97b3d SAE-PK: AP functionality
This adds AP side functionality for SAE-PK. The new sae_password
configuration parameters can now be used to enable SAE-PK mode whenever
SAE is enabled.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-06-02 23:25:22 +03:00
Jouni Malinen
6b9e99e571 SAE-PK: Extend SAE functionality for AP validation
This adds core SAE functionality for a new mode of using SAE with a
specially constructed password that contains a fingerprint for an AP
public key and that public key being used to validate an additional
signature in SAE confirm from the AP.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-06-02 23:25:22 +03:00
Jouni Malinen
661e661186 OCV: Allow OCI channel to be overridden for testing (AP)
Add hostapd configuration parameters oci_freq_override_* to allow the
OCI channel information to be overridden for various frames for testing
purposes. This can be set in the configuration and also updated during
the runtime of a BSS.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-30 00:04:53 +03:00
Jouni Malinen
5a7bcb7725 OSEN: Do not send the actual BIGTK to OSEN STAs
OSEN STAs are not authenticated, so do not send the actual BIGTK for
them so that they cannot generate forged protected Beacon frames. This
means that OSEN STAs cannot enable beacon protection.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-29 21:25:02 +03:00
Jouni Malinen
2d6cc0e670 FT: Do not expose GTK/IGTK in FT Reassociation Response frame in OSEN
Do not include the actual GTK/IGTK value in FT protocol cases in OSEN or
with DGAF disabled (Hotspot 2.0). This was already the case for the
EAPOL-Key cases of providing GTK/IGTK, but the FT protocol case was
missed. OSEN cannot really use FT, so that part is not impacted, but it
would be possible to enable FT in a Hotspot 2.0 network that has DGAF
disabled.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-29 21:25:02 +03:00
Jouni Malinen
a998337895 WNM: Do not expose GTK/IGTK in WNM Sleep Mode Response frame in OSEN
Do not include the actual GTK/IGTK value in WNM Sleep Mode Response
frame if WNM Sleep Mode is used in OSEN or in a network where use of GTK
is disabled. This was already the case for the EAPOL-Key cases of
providing GTK/IGTK, but the WNM Sleep Mode exit case was missed.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-29 21:04:40 +03:00
Hu Wang
d578e890eb OWE: Skip beacon update of transition BSS if it is not yet enabled
When a single hostapd process manages both the OWE and open BSS for
transition mode, owe_transition_ifname can be used to clone the
transition mode information (i.e., BSSID/SSID) automatically. When both
BSSs use ACS, the completion of ACS on the 1st BSS sets state to
HAPD_IFACE_ENABLED and the OWE transition mode information is updated
for all the other BSSs. However, the 2nd BSS is still in the ACS phase
and the beacon update messes up the state for AP startup and prevents
proper ACS competion.

If 2nd BSS is not yet enabled (e.g., in ACS), skip beacon update and
defer OWE transition information cloning until the BSS is enabled.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-26 16:23:39 +03:00
Jouni Malinen
8ee0bc622a OCV: Disconnect STAs that do not use SA Query after CSA
Verify that all associated STAs that claim support for OCV initiate an
SA Query after CSA. If no SA Query is seen within 15 seconds,
deauthenticate the STA.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-25 21:57:04 +03:00
Jouni Malinen
01ceb88c77 OCV: Report validation errors for (Re)Association Request frames
Add the OCV-FAILURE control interface event to notify upper layers of
OCV validation issues in FT and FILS (Re)Association Request frames.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-25 20:46:32 +03:00
Jouni Malinen
a3556d5813 OCV: Report validation errors for EAPOL-Key messages in AP mode
Add the OCV-FAILURE control interface event to notify upper layers of
OCV validation issues in EAPOL-Key msg 2/4 and group 2/2.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-25 19:09:12 +03:00
Jouni Malinen
d52067a5b6 OCV: Report validation errors for SA Query Request/Response in AP mode
Add a new OCV-FAILURE control interface event to notify upper layers of
OCV validation issues. This commit adds this for SA Query processing in
AP mode.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-25 18:42:00 +03:00
Jouni Malinen
52579be860 OCV: Move "OCV failed" prefix to callers
Make reporting of OCV validation failure reasons more flexible by
removing the fixed prefix from ocv_verify_tx_params() output in
ocv_errorstr so that the caller can use whatever prefix or encapsulation
that is most appropriate for each case.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-25 18:34:59 +03:00
Jouni Malinen
d9532eb70f Debug print PMK-R0/R1 and PMKR0/R1Name in the helper functions
There is no need to have all callers debug print these separately.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-05-23 21:45:29 +03:00
Rajkumar Manoharan
dd2daf0848 HE: Process HE 6 GHz band capab from associating HE STA
Process HE 6 GHz band capabilities in (Re)Association Request frames and
pass the information to the driver.

Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
2020-05-17 17:22:34 +03:00
Rajkumar Manoharan
db603634a9 HE: Add 6 GHz Band Capabilities element in Beacon and response frames
Construct HE 6 GHz Band Capabilities element (IEEE 802.11ax/D6.0,
9.4.2.261) from HT and VHT capabilities and add it to Beacon, Probe
Response, and (Re)Association Response frames when operating on the 6
GHz band.

Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
2020-05-17 16:47:18 +03:00
neo_jou
025ab330b4 ACS: Channel selection based freqlist
When doing ACS, check freqlist also if it is specified.

Signed-off-by: neojou <neojou@gmail.com>
2020-05-17 01:31:19 +03:00
Jouni Malinen
d3cab56c04 Rename WPA_ALG_IGTK to use the correct cipher name for BIP
IGTK is the key that is used a BIP cipher. WPA_ALG_IGTK was the
historical name used for this enum value when only the AES-128-CMAC
based BIP algorithm was supported. Rename this to match the style used
with the other BIP options.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-05-17 01:31:19 +03:00
Johannes Berg
bd1aebbd08 hostapd: Extend RESET_PN for BIGTK
Extend the RESET_PN command to allow resetting the BIGTK PN
for testing.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-05-17 01:31:16 +03:00
Jouni Malinen
5a04a76aa2 Ignore Management frames while AP interface is not fully enabled
It is possible for drivers to report received Management frames while AP
is going through initial setup (e.g., during ACS or DFS CAC). hostapd
and the driver is not yet ready for actually sending out responses to
such frames at this point and as such, it is better to explicitly ignore
such received frames rather than try to process them and have the
response (e.g., a Probe Response frame) getting dropped by the driver as
an invalid or getting out with some incorrect information.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-05-16 12:16:34 +03:00
Jouni Malinen
c82535edd6 Move deauthentication at AP start to be after beacon configuration
This allows nl80211-based drivers to get the frame out. The old earlier
location resulted in the driver operation getting rejected before the
kernel was not ready to transmit the frame in the BSS context of the AP
interface that has not yet been started.

While getting this broadcast Deauthentication frame transmitted at the
BSS start is not critical, it is one more chance of getting any
previously associated station notified of their previous association not
being valid anymore had they missed previous notifications in cases
where the AP is stopped and restarted.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-05-16 11:38:09 +03:00
Jouni Malinen
094c8a6218 Remove unnecessary key clearing at AP start with nl80211
cfg80211 takes care of key removal when link/association is lost, so
there is no need to explicitly clear old keys when starting AP.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-05-16 11:28:03 +03:00
Jouni Malinen
98e4b38403 DPP2: Chirping in hostapd Enrollee
Add a new hostapd control interface command "DPP_CHIRP own=<BI ID>
iter=<count>" to request chirping, i.e., sending of Presence
Announcement frames, to be started. This follows the model of similar
wpa_supplicant functionality from commit 562f77144c ("DPP2: Chirping
in wpa_supplicant Enrollee"). The hostapd case requires the AP to be
started without beaconing, i.e., with start_disabled=1 in hostapd
configuration, to allow iteration of channels needed for chirping.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-13 17:59:05 +03:00
Jouni Malinen
95471fc3e8 Handle hostapd_for_each_interface() at the process termination
Clean struct hapd_interfaces pointers and interface count during
deinitialization at the end of theh ostapd process termination so that a
call to hostapd_for_each_interface() after this does not end up
dereferencing freed memory. Such cases do not exist before this commit,
but can be added after this, e.g., for DPP needs.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-13 17:39:01 +03:00
Jouni Malinen
890ae336c0 DPP2: Clean up CONFIG_DPP2 use with configurator connectivity IE
Avoid duplicated return statement in CONFIG_DPP2=y builds.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-11 17:30:26 +03:00
Jouni Malinen
6dcb8aaf13 DPP2: Reconfig Announcement relaying from AP to Controller
Recognize the Reconfig Announcement message type and handle it similarly
to the Presence Announcement in the Relay, i.e., send it to the first
Controller if the local Configurator does not have matching C-sign-key.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-11 17:26:11 +03:00
Jouni Malinen
24b01c706b DPP2: Reconfig Authentication Response processing and Confirm generation
Extend Configurator functionality to process Reconfig Authentication
Response message, derive the needed keys, and generate Reconfig
Authentication Confirm message.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-11 17:26:09 +03:00
Jouni Malinen
3774b6bd03 DPP2: Reconfig Authentication Request generation and transmission
Extend Configurator functionality to sign a special Connector for
reconfiguration and reply with Reconfig Authentication Request frame
when Reconfig Announcement frame is received with a matching C-sign key
hash value.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-11 16:41:33 +03:00
Jouni Malinen
66ac616cdb DPP2: Process received Reconfig Announcement frame
Check if there is a matching Configurator and be ready to initiate
Reconfig Authentication (which itself is not included in this commit).

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-11 16:41:33 +03:00
Jouni Malinen
12c8eacf73 DPP: Allow version number to be overridden for testing purposes
"SET dpp_version_override <ver>" can now be used to request
wpa_supplicant and hostapd to support a subset of DPP versions. In
practice, the only valid case for now is to fall back from DPP version 2
support to version 1 in builds that include CONFIG_DPP2=y.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-04 00:37:45 +03:00
Jouni Malinen
9561925b4d DPP2: Detect PFS downgrade attack while processing EAPOL-Key msg 2/4
Do not allow association to continue if the local configuration enables
PFS and the station indicates it supports PFS, but PFS was not
negotiated for the association.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-04 00:37:44 +03:00
Jouni Malinen
b11a12401a DPP2: Add DPP KDE into EAPOL-Key msg 3/4 when using DPP AKM
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-04 00:37:44 +03:00
Jouni Malinen
42acf1292d DPP2: Add Protocol Version attribute to network introduction messages
This can be used to determine whether to try to negotiate PFS (only
available with version 2 or higher).

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-05-04 00:37:44 +03:00
Jouni Malinen
a7d6098fb4 Add PRINTF_FORMAT for printf wrapper functions
This avoids compiler format-nonliteral warnings ("format string is not a
string literal").

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-05-02 21:04:17 +03:00
Jouni Malinen
a803ba4f9d Use more specific reason codes for 4-way handshake timeouts
IEEE 802.11 defines reason codes for indicating 4-way handshake and
group key handshake timeouts. Use those reason codes instead of the more
generic one for these particular cases in the Authenticator state
machine.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-04-29 13:00:53 +03:00
Jouni Malinen
2c55e67aaf airtime_policy: Convert Boolean to C99 bool
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-04-24 17:06:50 +03:00
Jouni Malinen
0365458eb8 HE: Replace Boolean with C99 bool
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-04-24 17:06:50 +03:00
Jouni Malinen
5e5eb5a312 MACsec: Convert Boolean to C99 bool
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-04-24 17:06:50 +03:00
Jouni Malinen
37e3501bf7 FST: Convert Boolean to C99 bool
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-04-24 17:06:50 +03:00
Jouni Malinen
3dc69721e8 EAPOL auth: Convert Boolean to C99 bool
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-04-24 17:06:50 +03:00
Jouni Malinen
56024a233a WPA auth: Convert Boolean to C99 bool
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-04-24 17:06:50 +03:00
Jouni Malinen
bb9e3935dd driver: Add second driver capability flags bitmap
All 64 bits of the capability flags bitmap are used, so add a new
variable to hold future capability bits.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-04-19 15:53:02 +03:00
Disha Das
6b1c590ebb Allow TKIP support to be removed from build
Add a build flag CONFIG_NO_TKIP=y to remove all TKIP functionality from
hostapd and wpa_supplicant builds. This disables use of TKIP as both the
pairwise and group cipher. The end result does not interoperate with a
WPA(v1)-only device or WPA+WPA2 mixed modes.

Signed-off-by: Disha Das <dishad@codeaurora.org>
2020-04-17 23:51:58 +03:00
Jouni Malinen
a6c689d354 FT: Testing override for RSNXE Used subfield in FTE (AP)
Allow hostapd to be requested to override the RSNXE Used subfield in FT
reassociation case for testing purposes with "ft_rsnxe_used=<0/1/2>"
where 0 = no override, 1 = override to 1, and 2 = override to 0.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-04-16 23:39:57 +03:00
Jouni Malinen
5344af7d22 FT: Discard ReassocReq with mismatching RSNXE Used value
Discard the FT Reassociation Request frame instead of rejecting it
(i.e., do not send Reassociation Response frame) if RSNXE Used is
indicated in FTE, but no RSNXE is included even though the AP is
advertising RSNXE.

While there is not really much of a difference between discarding and
rejecting the frame, this discarding behavior is what the standard says
for this type of an error case.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-04-14 16:37:35 +03:00
Jouni Malinen
153333ef6b FT RRB: Remove confusing debug print about extra data
The "FT: Ignore extra data in end" hexdump is quite confusing since it
shows all the IEs that were actually either processed or forwarded.
There is no code path that could reach this debug print with actual real
extra data. Remove it and the dead increment of pos to avoid warnings
from static analyzers.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-04-04 23:42:05 +03:00
Jouni Malinen
d867e11811 FT: Remove and re-add STA entry after FT protocol success with PMF
Allow STA entry to be removed and re-added to the driver with PMF is
used with FT. Previously, this case resulted in cfg80211 rejecting STA
entry update after successful FT protocol use if the association had not
been dropped and it could not be dropped for the PMF case in
handle_auth().

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-04-04 21:53:10 +03:00
Jouni Malinen
bf9f49396b OWE: Remove check for unexpected DH Parameter IE use with other AKMs
While the Diffie-Hellman Parameter element is defined in RFC 8110
explicitly for use witht he OWE AKM, it has now been proposed to be used
with another AKM (DPP). Should any other AKM be extended in similar
manner in the future, the check against unexpected use could result in
additional interoperability issues. Remove that and instead, ignore the
unexpected Diffie-Hellman Parameter element if it is included in
(Re)Association Request frame when any other AKM is negotiated.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-04-03 12:18:11 +03:00
Jouni Malinen
e4eb009d98 DPP2: Add Connector and C-sign-key in psk/sae credentials for reconfig
If the Enrollee indicates support for DPP R2 or newer, add Connector and
C-sign-key in psk/sae credentials (i.e., cases where DPP AKM is not
enabled) for reconfiguration. Extend processing of such credentials in
wpa_supplicant network profile addition to handle this new case
correctly by not setting key_mgmt=DPP based on Connector being present,
but by looking at the actual akm value in the config object.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-04-02 21:34:49 +03:00
Jouni Malinen
a371164f88 Process received WNM Notification Request for beacon protection failures
Report received notifications for beacon protection failures in syslog
and control interface.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-04-01 16:30:12 +03:00
Sergey Matyukevich
91498a1225 hostapd: DFS for channel switch in repeater mode
In repeater mode remote AP may request channel switch to a new channel.
Check if DFS is required for the new channel before proceeding with
normal AP operations. Start CAC procedure if radar detection is required
and channel is not yet marked as available.

Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
2020-03-29 21:15:16 +03:00
Sergey Matyukevich
683e7c7559 DFS: Add new hostapd_is_dfs_overlap() helper
Add a new hostapd_is_dfs_overlap() helper function to DFS module. This
function tells whether the selected frequency range overlaps with DFS
channels in the current hostapd configuration. Selected frequency reange
is specified by its center frequency and bandwidth.

Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
2020-03-29 21:15:16 +03:00
Sergey Matyukevich
7988767393 DFS: Rename and export hostapd_config_dfs_chan_available helper
Rename DFS helper hostapd_config_dfs_chan_available() to
hostapd_is_dfs_chan_available(). Enable access to this helper function
from other hostapd components.

Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
2020-03-29 21:15:16 +03:00
Alexander Wetzel
3f88d2ba0d AP: Drop not needed condition to delete PTK ID 1
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
2020-03-29 21:15:16 +03:00
Jouni Malinen
54e2961f80 Add a hostapd testing option for skipping association pruning
The new skip_prune_assoc=1 parameter can be used to configure hostapd
not to prune associations from other BSSs operated by the same process
when a station associates with another BSS. This can be helpful in
testing roaming cases where association and authorization state is
maintained in an AP when the stations returns.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-28 20:39:19 +02:00
Jouni Malinen
7b156a3c5a wpa_auth: Use printf format %zu instead of type casts
Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-28 19:54:10 +02:00
Jouni Malinen
f83d3491b9 wpa_auth: Do not split strings into multiple lines
Avoid unnecessary splitting of long string constants into multiple
lines.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-28 19:48:32 +02:00
Jouni Malinen
9385f03feb wpa_auth: Coding style cleanup for pointer is NULL comparisons
Use !ptr instead of ptr == NULL.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-28 19:36:00 +02:00
Jouni Malinen
62e12afcf1 wpa_auth: Clean up pointer dereferences
Use local variables to avoid sm->wpa_auth->conf type of dereferences
where multiple instances within a function can be cleaned up.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-28 19:29:12 +02:00
Jouni Malinen
7c021dec3a DPP2: Allow AP to require or reject PFS
The new hostapd configuration parameter dpp_pfs can be used to specify
how PFS is applied to associations. The default behavior (dpp_pfs=0)
remains same as it was previously, i.e., allow the station to decide
whether to use PFS. PFS use can now be required (dpp_pfs=1) or rejected
(dpp_pfs=2).

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-28 12:33:48 +02:00
Jouni Malinen
ca57d5f553 Return an enum from wpa_validate_wpa_ie()
This is more specific then returning a generic int and also allows the
compiler to do more checks.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-28 12:30:46 +02:00
Sathishkumar Muruganandam
2b4f9ce287 hostapd: Add HE bit in BSSID Information field of own Neighbor Report
Add definition for HE bit in neighbor report BSSID Information field
from IEEE P802.11ax/D6.0, 9.4.2.36 Neighbor Report element.

Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
2020-03-27 23:52:24 +02:00
Jouni Malinen
db1ef82538 DPP2: Presence Announcement processing in AP/Relay
Process the received Presence Announcement frames in AP/Relay. If a
matching bootstrapping entry for the peer is found in a local
Configurator, that Configurator is used. Otherwise, the frame is relayed
to the first configured Controller (if available).

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-27 20:05:25 +02:00
Jouni Malinen
6f5bc15bec DPP2: Configurator Connectivity indication
Add a new hostapd configuration parameter
dpp_configurator_connectivity=1 to request Configurator connectivity to
be advertised for chirping Enrollees.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-27 20:05:25 +02:00
Jouni Malinen
514cc49ba5 DPP: Store global pointers in struct dpp_authentication
Set the global pointer and msg_ctx when allocating struct
dpp_authentication instead of needing to pass these to
dpp_set_configurator().

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-27 17:44:06 +02:00
Jouni Malinen
b7275a8142 Update STA flags to the driver immediately on disconnection
hostapd (and wpa_supplicant in AP mode) was internally updating the STA
flags on disconnection cases to remove authorization and association.
However, some cases did not result in immediate update of the driver STA
entry. Update all such cases to send out the update to the driver as
well to reduce risk of race conditions where new frames might be
accepted for TX or RX after the port authorization or association has
been lost and configured keys are removed.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-26 17:51:03 +02:00
Jouni Malinen
82cc0b0cc2 Allow hostapd AP to advertise Transition Disable KDE
The new hostapd configuration parameter transition_disable can now be
used to configure the AP to advertise that use of a transition mode is
disabled. This allows stations to automatically disable transition mode
by disabling less secure network profile parameters.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-26 00:12:41 +02:00
Noam Shaked
e520de8dbe Add ACS support for 60 GHz channel bonding
hostapd will trigger EDMG auto channel selection by setting
QCA_WLAN_VENDOR_ATTR_ACS_EDMG_ENABLED. The 60 GHz driver will be
called to start an auto channel selection and will return the
primary channel and the EDMG channel.

Signed-off-by: Noam Shaked <nshaked@codeaurora.org>
2020-03-24 22:15:32 +02:00
Alexander Wetzel
862aac1fcd AP: Support Extended Key ID
Support Extended Key ID in hostapd according to IEEE Std 802.11-2016.

Extended Key ID allows to rekey pairwise keys without the otherwise
unavoidable MPDU losses on a busy link. The standard is fully backward
compatible, allowing an AP to serve STAs with and without Extended Key
ID support in the same BSS.

Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
2020-03-23 11:43:10 +02:00
Jouni Malinen
ae7193611f Limit maximum number of pending SA Queries
There is no point in starting a huge number of pending SA Queries, so
limit the number of pending queries to 1000 to have an explicit limit
for how large sa_query_count can grow.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-22 18:50:04 +02:00
Jouni Malinen
a55ecfeabe Allow RSNXE to be removed from Beacon frames for testing purposes
The new hostapd configuration parameter no_beacon_rsnxe=1 can be used to
remove RSNXE from Beacon frames. This can be used to test protection
mechanisms for downgrade attacks.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-21 00:24:03 +02:00
Jouni Malinen
b7366a942a FT: Omit RSNXE from FT protocol Reassociation Response when needed
The previous design for adding RSNXE into FT was not backwards
compatible. Move to a new design based on 20/332r3 to avoid that issue
by not include RSNXE in the FT protocol Reassociation Response frame so
that a STA not supporting RSNXE can still validate the FTE MIC
correctly.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-21 00:01:47 +02:00
Jouni Malinen
497ae9f004 FT: Verify that RSNXE is used consistently in Reassociation Request
Verify that the STA includes RSNXE if it indicated in FTE that RSNXE is
used and the AP is also using RSNXE. This is needed to protect against
downgrade attacks based on the design proposed in 20/332r3.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-20 21:33:02 +02:00
Jouni Malinen
51d1924bd8 FT: Set the new RSNXE Used subfield in FT reassociation
This is a workaround needed to keep FT protocol backwards compatible for
the cases where either the AP or the STA uses RSNXE, but the other one
does not. This commit adds setting of the new field to 1 in
Reassociation Request/Response frame during FT protocol when the STA/AP
uses RSNXE in other frames. This mechanism is described in 20/332r3.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-20 21:23:48 +02:00
Jouni Malinen
46e147fcdc Allow RSNE/RSNXE to be replaced in FT protocol Reassocation Response frame
This can be used to test station side behavior for FT protocol
validation steps.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-15 10:39:17 +02:00
Hrishikesh Vidwans
d9a7b71a78 AP: Fix regression in frequency check for a usable EDMG channel
Commit 5f9b4afd ("Use frequency in HT/VHT validation steps done before
starting AP") modified hostapd_is_usable_edmg() to use freq instead of
channel numbers. Unfortunately, it did not convert the frequency
calculation correctly and this broke EDMG functionality.

Fix the frequency calculation so that EDMG channel 9 works again.

Fixes: 5f9b4afdfa ("Use frequency in HT/VHT validation steps done before starting AP")
Signed-off-by: Hrishikesh Vidwans <hvidwans@codeaurora.org>
2020-03-11 17:54:13 +02:00
Jouni Malinen
10223b501b SAE: Expose sae_write_commit() error cases to callers
Check whether an error is reported from any of the functions that could
in theory fail and if so, do not proceed with the partially filled SAE
commit buffer.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-08 16:59:42 +02:00
Jouni Malinen
7f1f69e897 SAE: Check hmac_sha256() result in sae_token_hash()
In theory, hmac_sha256() might fail, so check for that possibility
instead of continuing with undetermined index value that could point to
an arbitrary token entry.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-08 16:51:30 +02:00
Jouni Malinen
7dcc5f7feb SAE: Check sta pointer more consistently in testing code
send_auth_reply() could be called with sta == NULL in certain error
conditions. While that is not applicable for this special test
functionality for SAE, the inconsistent checks for the sta pointer could
result in warnings from static analyzers. Address this by explicitly
checking the sta pointer here.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-08 16:32:47 +02:00
Jouni Malinen
15d63c6043 Clean up hostapd_get_he_twt_responder() processing
mode->he_capab is an array and as such, there is no point in checking
whether it is NULL since that cannot be the case. Check for the
he_supported flag instead. In addition, convert the TWT responder
capability bit into a fixed value 1 to avoid any surprising to the
callers. In practice, neither of these changes results in different
behavior in the current implementation, but this is more robust.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-08 16:28:03 +02:00
Jouni Malinen
4d64fd37b7 Allow RSNE in EAPOL-Key msg 3/4 to be replaced for testing purposes
The new hostapd configuration parameter rsne_override_eapol can now be
used similarly to the previously added rsnxe_override_eapol to override
(replace contents or remove) RSNE in EAPOL-Key msg 3/4. This can be used
for station protocol testing to verify sufficient checks for RSNE
modification between the Beacon/Probe Response frames and EAPOL-Key msg
3/4.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-07 16:45:52 +02:00
Jouni Malinen
9128b67269 Extend hostapd rsnxe_override_eapol to allow IE removal
Previous implementation was determining whether the override value was
set based on its length being larger than zero. Replace this with an
explicit indication of whether the parameter is set to allow zero length
replacement, i.e., remove of RSNXE from EAPOL-Key msg 3/4.

In addition, move IE replacement into a more generic helper function to
allow this to be used with other IEs as well.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-07 16:39:36 +02:00
Jouni Malinen
43ededa9c7 Do not override WDS VLAN assignment for STA
The 4-address frames WDS design in mac80211 uses VLAN interfaces
similarly to the way VLAN interfaces based on VLAN IDs are used. The EAP
authentication case ended up overriding the WDS specific assignment even
when the RADIUS server did not assign any specific VLAN for the STA.
This broke WDS traffic.

Fix this by skipping VLAN assignment to VLAN ID 0 for STAs that have
been detected to use 4-address frames.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-03-07 13:56:56 +02:00
Pravas Kumar Panda
f64b601c47 DFS: Add support for 80+80 MHz when going through channel switch
After a radar signal is detected, the AP should switch to another
channel, but in the case of 80+80 MHz, channel switch failed because
hostapd did not select the secondary channel in the process. Fix this by
selecting a secondary channel in the case of 80+80 MHz.

Signed-off-by: Xin Wang <xwangw@codeaurora.org>
Signed-off-by: Pravas Kumar Panda <kumarpan@codeaurora.org>
2020-03-06 21:44:31 +02:00
Hu Wang
0a76a0b965 OWE: Fix PTK derivation workaround for interoperability
The initial implementation of the PTK derivation workaround for
interoperability with older OWE implementations forced
WPA_KEY_MGMT_PSK_SHA256 to be used for all of PTK derivation. While that
is needed for selecting which hash algorithm to use, this was also
changing the length of the PTK components and by doing so, did not
actually address the backwards compatibility issue.

Fix this by forcing SHA256 as the hash algorithm in PTK derivation
without changing the PTK length calculation for OWE when
owe_ptk_workaround is enabled.

Fixes: 65a44e849a ("OWE: PTK derivation workaround in AP mode")
Fixes: 8b138d2826 ("OWE: PTK derivation workaround in STA mode")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-06 21:44:31 +02:00
Alexander Wetzel
982b9cf029 Fix a wrong key_flag when deleting 802.1X WEP keys
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
2020-03-05 00:13:20 +02:00
Alexander Wetzel
d37c05e5b5 AP: Don't try to set NULL WEP default key
hostapd_broadcast_wep_set() can be called without a WEP key set.
Don't try to install a default key in that case.

This patch is not critical for the new API. With key_flag we just would
report an (ignored) error and do nothing. With the patch we simply do
nothing.

Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
2020-03-05 00:03:56 +02:00
Jouni Malinen
8f89e57ab5 DFS: More debug prints on channel selection after radar detection
This makes it easier to understand what is happening when a new channel
needs to be selected based on a radar detection event.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-03-03 18:58:08 +02:00
Seevalamuthu Mariappan
4b37d24285 hostapd: Fix to downgrade bandwidth in radar detection
Upon radar detection we used to search channels with the same bandwidth.
This way we might not find any other channels. If there are no channels
available with that bandwidth the AP service will be stopped. To avoid
this problem, also search a suitable channel by downgrading the
bandwidth. This scenario is applicable during CAC as well.

Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
2020-03-03 18:37:16 +02:00
Seevalamuthu Mariappan
7242087d1c DFS: Do not process radar event while disabling an interface
In the normal case hostapd_disable_iface() and hostapd_enable_iface()
will be done while switching to another DFS channel upon radar
detection. In certain scenarios radar detected event can come while
hostapd_disable_iface() is in progress and iface->current_mode will be
NULL in that scenario. Previously, we did not check for this scenario
and proceeded with the radar detection logic which can trigger a
segmentation fault. To fix this, avoid proceeding the radar detection
event if iface->current_mode is NULL.

Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
2020-03-03 17:10:31 +02:00
Ilan Peer
e636bc855f WPA: Rename FILS wrapped data
IEEE P802.11az/D2.0 renamed the FILS Wrapped Data element,
removing the FILS prefix. Change the code accordingly.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2020-02-29 23:30:55 +02:00
Ilan Peer
c4988e73c0 driver: Extend send_mlme() with wait option
PASN authentication can be performed while a station interface is
connected to an AP. To allow sending PASN frames while connected, extend
the send_mlme() driver callback to also allow a wait option. Update the
relevant drivers and wpa_supplicant accordingly.

hostapd calls for send_mlme() are left unchanged, since the wait option
is not required there.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2020-02-29 23:03:20 +02:00
Jouni Malinen
200c7693c9 Make WEP functionality an optional build parameter
WEP should not be used for anything anymore. As a step towards removing
it completely, move all WEP related functionality to be within
CONFIG_WEP blocks. This will be included in builds only if CONFIG_WEP=y
is explicitly set in build configuration.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-02-29 17:45:25 +02:00
Jouni Malinen
bca44f4e4e WPS: Remove static-WEP-only workaround
WEP provisioning was removed from WPS v2, so this workaround
functionality has not been applicable. Remove it completely.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-02-29 16:56:44 +02:00
Neo Jou
b7f1d4f4d6 ACS: Allow hw_mode=any to be used with internal ACS algorithm
This was already supported in the offload ACS case and this commit
completes support for this with the internal ACS algorithm.

Signed-off-by: Neo Jou <neojou@gmail.com>
2020-02-29 11:23:03 +02:00
Neo Jou
d07f1ade90 ACS: Determine mode when using hw_mode=any
Set iface->current_mode and iface->conf->hw_mode when completing ACS
based on the selected channel in the hw_mode=any case.

Signed-off-by: Neo Jou <neojou@gmail.com>
2020-02-29 11:23:03 +02:00
Neo Jou
c60362e6e8 ACS: Extend acs_find_ideal_chan() to support multiple modes
This is preparation for being able to support hw_mode=any to select the
best channel from any supported mode.

Signed-off-by: Neo Jou <neojou@gmail.com>
2020-02-29 11:23:03 +02:00
Neo Jou
141a8815e7 ACS: Extend acs_request_scan() to support multiple modes
Add suitable channel frequencies from all modes into the scan parameters
when a single mode is not specified for ACS. This is preparation for
being able to support hw_mode=any to select the best channel from any
supported mode.

Signed-off-by: Neo Jou <neojou@gmail.com>
2020-02-29 11:23:03 +02:00
Neo Jou
f3c44a196f ACS: Extend interference factor calculation for all modes
This is preparation for being able to support hw_mode=any to select the
best channel from any supported mode.

Signed-off-by: Neo Jou <neojou@gmail.com>
2020-02-29 11:23:03 +02:00
Neo Jou
070522e5b2 ACS: Extend acs_find_chan() for all modes
This is preparation for being able to support hw_mode=any to select the
best channel from any supported mode.

Signed-off-by: Neo Jou <neojou@gmail.com>
2020-02-29 11:23:03 +02:00
Neo Jou
4c1ffb45e4 ACS: Extend acs_surveys_are_sufficient() for all modes
This is preparation for being able to support hw_mode=any to select the
best channel from any supported mode.

Signed-off-by: Neo Jou <neojou@gmail.com>
2020-02-29 11:23:03 +02:00
Neo Jou
3d09be41a8 ACS: Clear all modes in acs_cleanup()
This is preparation for being able to support hw_mode=any to select the
best channel from any supported mode.

Signed-off-by: Neo Jou <neojou@gmail.com>
2020-02-29 11:23:03 +02:00
Neo Jou
499c37b729 ACS: Extend hostapd_get_mode_channel() to find from any mode
This is preparation for being able to support hw_mode=any to select the
best channel from any supported mode.

Signed-off-by: Neo Jou <neojou@gmail.com>
2020-02-29 11:23:03 +02:00
Jouni Malinen
a62d761856 ACS: Fix spelling of "interference"
Signed-off-by: Jouni Malinen <j@w1.fi>
2020-02-29 11:23:03 +02:00
Jouni Malinen
114d124186 SAE: Fix PMKID derivation for OKC
SAE authentication derives PMKID differently from the EAP cases. The
value comes from information exchanged during SAE authentication and
does not bind in the MAC addresses of the STAs. As such, the same PMKID
is used with different BSSIDs. Fix both the hostapd and wpa_supplicant
to use the previous PMKID as is for OKC instead of deriving a new PMKID
using an incorrect derivation method when using an SAE AKM.

This fixes use of opportunistic key caching with SAE.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-02-28 18:41:20 +02:00
Janusz Dziedzic
4b04223f24 hostapd: Replace UDP ctrl_iface global cookies with per-instance ones
The cookie values for UDP control interface commands was defined as a
static global array. This did not allow multi-BSS test cases to be
executed with UDP control interface. For example, after
    hapd1 = hostapd.add_bss(apdev[0], ifname1, 'bss-1.conf')
    hapd2 = hostapd.add_bss(apdev[0], ifname2, 'bss-2.conf')

hapd1->ping() did not work.

Move those cookie values to per-instance location in struct
hapd_interfaces and struct hostapd_data to fix this.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
2020-02-23 17:48:34 +02:00
Alexander Wetzel
1a7963e36f AP: Allow PTK rekeying without Ext KeyID to be disabled as a workaround
Rekeying a pairwise key using only keyid 0 (PTK0 rekey) has many broken
implementations and should be avoided when using or interacting with
one. The effects can be triggered by either end of the connection and
range from hardly noticeable disconnects over long connection freezes up
to leaking clear text MPDUs.

To allow affected users to mitigate the issues, add a new hostapd
configuration option "wpa_deny_ptk0_rekey" to replace all PTK0 rekeys
with disconnection. This requires the station to reassociate to get
connected again and as such, can result in connectivity issues as well.

Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
2020-02-23 12:22:49 +02:00
Jouni Malinen
7b26238d46 Do not skip MBO PMF check with the WPS special case WPA check exception
The MBO PMF check for AP SME in the driver case was added into a
location that is skipped for WPS processing. That was not really the
correct place for this since the skip_wpa_check label was supposed to
remain immediately following the WPA checks. While this does not really
have much of a practical impact, move the check around so that the
skip_wpa_check label remains where it is supposed to be.

Fixes: 4c572281ed ("MBO: Mandate use of PMF for WPA2+MBO association (AP)")
Signed-off-by: Jouni Malinen <j@w1.fi>
2020-02-22 19:20:44 +02:00
Ouden
fae7e64aa3 Save RM enabled capability of station with AP SME
Save RM enabled capability element of an associating station when
hostapd use the device AP SME similarly to how this information is saved
with SME-on-hostapd cases. This allows radio measurement operations
(e.g., REQ_BEACON) to be used.

Signed-off-by: Ouden <Ouden.Biz@gmail.com>
2020-02-22 19:20:44 +02:00
Jouni Malinen
1074d42416 Fix a typo in a comment
Signed-off-by: Jouni Malinen <j@w1.fi>
2020-02-22 19:20:44 +02:00
Jouni Malinen
8fe7ec6640 Remove Secondary Channel Offset element from Beacon/Probe Response frames
This element is not used in Beacon or Probe Response frames (which is
the reason why the standard does not indicate where exactly it would be
in those frames..); HT Operation element has this information and so
does Extended CSA element.

In practice, this reverts the functionality added in commit 76aab0305c
("Add secondary channel IE for CSA").

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-02-22 19:20:44 +02:00
Jouni Malinen
7f1529d2a5 Fix HE element order in Beacon and Probe Response frames
Spatial Reuse Parameter Set element is before MU EDCA Parameter Set
element.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-02-22 19:20:44 +02:00
Jouni Malinen
f3bcd69603 Remove CONFIG_IEEE80211N build option
Hardcoded CONFIG_IEEE80211N to be included to clean up implementation.
More or less all new devices support IEEE 802.11n (HT) and there is not
much need for being able to remove that functionality from the build.
Included this unconditionally to get rid of one more build options and
to keep things simpler.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-02-22 19:20:44 +02:00
Jouni Malinen
640d59942b Fix location of MDE and RSNXE in Beacon and Probe Response frames
Split the IEs from WPA authenticator state machine into separately added
IEs so that the exact location between these and other elements can be
controlled. This fixes the location of MDE and RSNXE in Beacon and Probe
Response frames. In addition, this swaps the order of BSS Load and RM
Enabled Capabilities elements in Beacon frames to get them into the
correct order (which was already used for Probe Response frames).
Furthermore, this fixes the buffer end checks for couple of elements to
make the implementation more consistent (though, in practice, there is
no impact from this since the old size limit was smaller than needed,
but still sufficiently large to have room for these).

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-02-22 19:20:44 +02:00
Jouni Malinen
16889aff40 Add BIGTK KDE and subelement similarly to IGTK
This provides the BIGTK updates to associated stations similarly to
IGTK.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-02-17 23:48:24 +02:00
Jouni Malinen
555dcd75ce Generate BIGTK and rekey it with IGTK
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-02-17 23:48:24 +02:00
Jouni Malinen
c1df321b6c AP mode indication of Beacon protection being enabled
Add the new Extended Capability bit for indicating Beacon protection.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-02-17 23:48:24 +02:00
Jouni Malinen
92d407dbd6 hostapd configuration for Beacon protection
Add a new hostapd configuration parameter beacon_prot=<0/1> to allow
Beacon protection to be enabled.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-02-17 23:48:24 +02:00
John Crispin
0b0ee0f15e HE: Propagate BSS color settings to nl80211
Add the code required to send the BSS color settings to the kernel.

Signed-off-by: John Crispin <john@phrozen.org>
2020-02-17 19:28:39 +02:00
Jouni Malinen
466e48dcd7 HT: Remove SMPS in AP mode
SM Power Save was described in somewhat unclear manner in IEEE Std
802.11n-2009 as far the use of it locally in an AP to save power. That
was clarified in IEEE Std 802.11-2016 to allow only a non-AP STA to use
SMPS while the AP is required to support an associated STA doing so. The
AP itself cannot use SMPS locally and the HT Capability advertisement
for this is not appropriate.

Remove the parts of SMPS support that involve the AP using it locally.
In practice, this reverts the following commits:
04ee647d58 ("HT: Let the driver advertise its supported SMPS modes for AP mode")
8f461b50cf ("HT: Pass the smps_mode in AP parameters")
da1080d721 ("nl80211: Advertise and configure SMPS modes")

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-02-16 13:58:54 +02:00
Mikhail Karpenko
8de0ff0fa1 HE: Add TWT responder extended capabilities field
Set the proper bits inside the extended capabilities field to indicate
support for TWT responder.

Tested-by: John Crispin <john@phrozen.org>
Signed-off-by: Mikhail Karpenko <karpenko@fastmail.com>
2020-02-16 12:41:24 +02:00
John Crispin
ab8c55358e HE: Dynamically turn on TWT responder support
This allows us to dynamically turn on TWT responder support using an
nl80211 attribute.

Signed-off-by: John Crispin <john@phrozen.org>
2020-02-16 12:37:47 +02:00
John Crispin
0cb39f4fd5 HE: Extend BSS color support
The HE Operation field for BSS color consists of a disabled, a partial,
and 6 color bits. The original commit adding support for BSS color
considered this to be a u8. This commit changes this to the actual
bits/values.

This adds an explicit config parameter for the partial bit. The disabled
is set to 0 implicitly if a bss_color is defined.

Interoperability testing showed that stations will require a BSS color
to be set even if the feature is disabled. Hence the default color is 1
when none is defined inside the config file.

Signed-off-by: John Crispin <john@phrozen.org>
2020-02-16 12:32:17 +02:00
Jouni Malinen
981b96caa9 WPS: Mark added PSK entry with wps=1 tag for per-Enrollee PSK case
Commit 2bab073dfe ("WPS: Add new PSK entries with wps=1 tag") added
this when writing the new entry into a file, but the in-memory update
did not get the tag. Add it there as well.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-02-16 11:54:36 +02:00
Jouni Malinen
2bab073dfe WPS: Add new PSK entries with wps=1 tag
Now that hostapd wpa_psk_file has a new tag for identifying PSKs that
can be used with WPS, add that tag to new entries for PSKs from WPS.
This makes it clearer where the PSK came from and in addition, this
allows the same PSK to be assigned if the same Enrollee goes through WPS
provisioning again.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-02-15 17:37:27 +02:00
Tomasz Jankowski
fde8e79463 WPS: Make it possible to use PSKs loaded from the PSK file
By default, when configuration file set wpa_psk_file, hostapd generated
a random PSK for each Enrollee provisioned using WPS and appended that
PSK to wpa_psk_file.

Changes that behavior by adding a new step. WPS will first try to use a
PSK from wpa_psk_file. It will only try PSKs with wps=1 tag.
Additionally it'll try to match enrollee's MAC address (if provided). If
it fails to find an appropriate PSK, it falls back to generating a new
PSK.

Signed-off-by: Tomasz Jankowski <tomasz.jankowski@plume.com>
2020-02-15 17:28:00 +02:00
Jouni Malinen
b27ed050db Do not split strings into multiple lines
Convert hostapd_config_read_wpa_psk() to the newer style of not
splitting strings into multiple lines.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-02-15 17:12:45 +02:00
Jouni Malinen
838180877f Use PMK_LEN macro instead of hardcoded value 64 (= 2 * 32)
Signed-off-by: Jouni Malinen <j@w1.fi>
2020-02-15 17:11:18 +02:00
Jouni Malinen
f5da5810c9 Check pbkdf2_sha1() result when generating PSK from PSK file
This function can fail in theory, so check the return value.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-02-15 17:10:08 +02:00
Sergey Matyukevich
e7d8842e6b OWE: Rename owe_assoc_req_process() parameter reason to status
In the function owe_assoc_req_process(), values assigned to the reason
argument imply that it should be renamed to status. Rename 'reason' to
'status' and modify the uses of owe_assoc_req_process() accordingly.

Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
2020-02-15 16:46:32 +02:00
Markus Theil
96a2a9a88b Send RM Enabled Capabilities element in (Re)Association Response frame
(Re)Association Response frames should include radio measurement
capabilities in order to let stations know if they can, e.g., use
neighbor requests.

I tested this commit with a Samsung S8, which does not send neighbor
requests without this commit and sends them afterwards.

Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
2020-02-10 06:51:42 +02:00
Jouni Malinen
641d79f165 SAE: Special test mode sae_pwe=3 for looping with password identifier
The new sae_pwe=3 mode can be used to test non-compliant behavior with
SAE Password Identifiers. This can be used to force use of
hunting-and-pecking loop for PWE derivation when Password Identifier is
used. This is not allowed by the standard and as such, this
functionality is aimed at compliance testing.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-02-10 05:13:13 +02:00
Jouni Malinen
8f8473cebb SAE: Fix peer-commit-scalar reuse check
Only one peer-commit-scalar value was stored for a specific STA (i.e.,
one per MAC address) and that value got replaced when the next SAE
Authentication exchange was started. This ended up breaking the check
against re-use of peer-commit-scalar from an Accepted instance when
anti-clogging token was requested. The first SAE commit message (the one
without anti-clogging token) ended up overwriting the cached
peer-commit-scalar value while leaving that instance in Accepted state.
The second SAE commit message (with anti-clogging token) added ended up
getting rejected if it used the same value again (and re-use is expected
in this particular case where the value was not used in Accepted
instance).

Fix this by using a separate pointer for storing the peer-commit-scalar
value that was used in an Accepted instance. There is no need to
allocate memory for two values, i.e., it is sufficient to maintain
separate pointers to the value and move the stored value to the special
Accepted state pointer when moving to the Accepted state.

This fixes issues where a peer STA ends up running back-to-back SAE
authentication within couple of seconds, i.e., without hostapd timing
out the STA entry for a case where anti-clogging token is required.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-02-08 07:19:53 +02:00
Qiwei Cai
c4bab72d96 Use secondary channel provided by ACS for HT40 if valid
Previously, hostapd ignored the secondary channel provided by ACS if
both HT40+ and HT40- are set in hostapd.conf. This change selects such
channel for HT40 if it's valid, which is more reasonable.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-02-03 02:03:32 +02:00
Ben Greear
16b789eefc Fix wmm compile on fedora-17 (gcc 4.7.2)
I guess this compiler does not like to initialize arrays with brackets?

Signed-off-by: Ben Greear <greearb@candelatech.com>
2020-02-03 02:03:32 +02:00
Jouni Malinen
7d9e320054 DPP: Received Configurator backup processing
Add local Configurator instance for each received Configurator backup.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-01-31 23:16:05 +02:00
Jouni Malinen
5e287724ee DPP: NFC negotiated connection handover
Add new control interface commands "DPP_NFC_HANDOVER_REQ own=<id>
uri=<URI>" and "DPP_NFC_HANDOVER_SEL own=<id> uri=<URI>" to support NFC
negotiated connection handover. These commands are used to report a DPP
URI received from a peer NFC Device in Handover Request and Handover
Select messages. The commands return peer bootstrapping information ID
or FAIL on failure. The returned ID is used similarly to any other
bootstrapping information to initiate DPP authentication.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-01-27 20:36:09 +02:00
Jouni Malinen
65a44e849a OWE: PTK derivation workaround in AP mode
Initial OWE implementation used SHA256 when deriving the PTK for all OWE
groups. This was supposed to change to SHA384 for group 20 and SHA512
for group 21. The new owe_ptk_workaround parameter can be used to enable
workaround for interoperability with stations that use SHA256 with
groups 20 and 21. By default, only the appropriate hash function is
accepted. When workaround is enabled (owe_ptk_workaround=1), the
appropriate hash function is tried first and if that fails, SHA256-based
PTK derivation is attempted. This workaround can result in reduced
security for groups 20 and 21, but is required for interoperability with
older implementations. There is no impact to group 19 behavior.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-01-24 00:47:41 +02:00
Jouni Malinen
5e32fb0170 SAE: Use Anti-Clogging Token Container element with H2E
IEEE P802.11-REVmd was modified to use a container IE for anti-clogging
token whenver H2E is used so that parsing of the SAE Authentication
frames can be simplified.

See this document for more details of the approved changes:
https://mentor.ieee.org/802.11/dcn/19/11-19-2154-02-000m-sae-anti-clogging-token.docx

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-01-21 13:13:56 +02:00
Jouni Malinen
e36a5894d0 SAE: Use H2E whenever Password Identifier is used
IEEE P802.11-REVmd was modified to require H2E to be used whenever
Password Identifier is used with SAE.

See this document for more details of the approved changes:
https://mentor.ieee.org/802.11/dcn/19/11-19-2154-02-000m-sae-anti-clogging-token.docx

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-01-21 13:13:56 +02:00
Vamsi Krishna
4bf78a79d0 ACS: Populate channel config from external ACS per documented behavior
Based on the now documented seg0/seg1 values from offloaded ACS, there
is a mismatch between the driver interface and internal hostapd use.

The value of segment0 field in ACS results is the index of the channel
center frequency for 20 MHz, 40 MHz, and 80M Hz channels. The value is
the center frequency index of the primary 80 MHz segment for 160 MHz and
80+80 MHz channels.

The value of segment1 field in ACS results is zero for 20 MHz, 40 MHz,
and 80 MHz channels. The value is the index of the channel center
frequency for 160 MHz channels and the center frequency index of the
secondary 80 MHz segment for 80+80 MHz channels.

However, in struct hostapd_config, for 160 MHz channels, the value of
the segment0 field is the index of the channel center frequency of 160
MHz channel and the value of the segment1 field is zero. Map the values
from ACS event into hostapd_config fields accordingly.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-01-09 20:22:12 +02:00
Vamsi Krishna
881177201a 6 GHz: Fix Channel Width value for 80+80 in 6 GHZ Operation Info field
The Channel Width field value is 0 for 20 MHz, 1 for 40 MHz, 2 for 80
MHz, and 3 for both 160 MHz and 80+80 MHz channels. The 80+80 MHz case
was not addressed previously correctly since it cannot be derived from
seg0 only.

The Channel Center Frequency Segment 0 field value is the index of
channel center frequency for 20 MHz, 40 MHz, and 80 MHz channels. The
value is the center frequency index of the primary 80 MHz segment for
160 MHz and 80+80 MHz channels.

The Channel Center Frequency Segment 1 field value is zero for 20 MHz,
40 MHz, and 80 MHz channels. The value is the index of the channel
center frequency for 160 MHz channel and the center frequency index of
the secondary 80 MHz segment for 80+80 MHz channels.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-01-09 17:43:28 +02:00
Jouni Malinen
b4fe37c4fa Silence compiler warning in no-NEED_AP_MLME builds
Make the dummy hostapd_hw_mode_txt() wrapper return "UNKNOWN" instead of
NULL to avoid a warning from a debug printf using %s with NULL.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-01-09 12:44:08 +02:00
Alexander Wetzel
a919a26035 Introduce and add key_flag
Add the new set_key() parameter "key_flag" to provide more specific
description of what type of a key is being configured. This is needed to
be able to add support for "Extended Key ID for Individually Addressed
Frames" from IEEE Std 802.11-2016. In addition, this may be used to
replace the set_tx boolean eventually once all the driver wrappers have
moved to using the new key_flag.

The following flag are defined:

  KEY_FLAG_MODIFY
    Set when an already installed key must be updated.
    So far the only use-case is changing RX/TX status of installed
    keys. Must not be set when deleting a key.

  KEY_FLAG_DEFAULT
    Set when the key is also a default key. Must not be set when
    deleting a key. (This is the replacement for set_tx.)

  KEY_FLAG_RX
    The key is valid for RX. Must not be set when deleting a key.

  KEY_FLAG_TX
    The key is valid for TX. Must not be set when deleting a key.

  KEY_FLAG_GROUP
    The key is a broadcast or group key.

  KEY_FLAG_PAIRWISE
    The key is a pairwise key.

  KEY_FLAG_PMK
    The key is a Pairwise Master Key (PMK).

Predefined and needed flag combinations so far are:

  KEY_FLAG_GROUP_RX_TX
    WEP key not used as default key (yet).

  KEY_FLAG_GROUP_RX_TX_DEFAULT
    Default WEP or WPA-NONE key.

  KEY_FLAG_GROUP_RX
    GTK key valid for RX only.

  KEY_FLAG_GROUP_TX_DEFAULT
    GTK key valid for TX only, immediately taking over TX.

  KEY_FLAG_PAIRWISE_RX_TX
    Pairwise key immediately becoming the active pairwise key.

  KEY_FLAG_PAIRWISE_RX
    Pairwise key not yet valid for TX. (Only usable with Extended Key ID
    support.)

  KEY_FLAG_PAIRWISE_RX_TX_MODIFY
    Enable TX for a pairwise key installed with KEY_FLAG_PAIRWISE_RX.

  KEY_FLAG_RX_TX
    Not a valid standalone key type and can only used in combination
    with other flags to mark a key for RX/TX.

This commit is not changing any functionality. It just adds the new
key_flag to all hostapd/wpa_supplicant set_key() functions without using
it, yet.

Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
2020-01-09 12:38:36 +02:00
Gurumoorthi Gnanasambandhan
99d8c4dca3 hostapd: Support VLAN offload to the driver
If the driver supports VLAN offload mechanism with a single netdev, use
that instead of separate per-VLAN netdevs.

Signed-off-by: Gurumoorthi Gnanasambandhan <gguru@codeaurora.org>
2020-01-09 00:48:57 +02:00
Gurumoorthi Gnanasambandhan
4d3ae54fbd Add vlan_id to driver set_key() operation
This is in preparation for adding support to use a single WLAN netdev
with VLAN operations offloaded to the driver. No functional changes are
included in this commit.

Signed-off-by: Gurumoorthi Gnanasambandhan <gguru@codeaurora.org>
2020-01-09 00:48:57 +02:00
Jouni Malinen
f822546451 driver: Move set_key() parameters into a struct
This makes it more convenient to add, remove, and modify the parameters
without always having to update every single driver_*.c implementation
of this callback function.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-01-09 00:48:57 +02:00
Jouni Malinen
3912cbd88d SAE: A bit optimized sae_confirm_immediate=2 for testing purposes
sae_confirm_immediate=2 can now be used in CONFIG_TESTING_OPTIONS=y
builds to minimize the latency between SAE Commit and SAE Confirm by
postponing transmission of SAE Commit until the SAE Confirm frame is
generated. This does not have significant impact, but can get the frames
tiny bit closer to each other over the air to increase testing coverage.
The only difference between sae_confirm_immediate 1 and 2 is in the
former deriving KCK, PMK, PMKID, and CN between transmission of the
frames (i.e., a small number of hash operations).

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2020-01-08 20:57:08 +02:00
Jouni Malinen
ccaabeaa03 driver: Remove unused send_ether() driver op
This was used only for FT RRB sending with driver_test.c and
driver_test.c was removed more than five years ago, so there is no point
in continuing to maintain this driver op.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-01-05 18:32:10 +02:00
Bilal Hatipoglu
3d41dd7c50 WPS: Add application extension data to WPS IE
Application Extension attribute is defined in WSC tech spec v2.07 page
104. Allow hostapd to be configured to add this extension into WPS IE in
Beacon and Probe Response frames. The implementation is very similar to
vendor extension.

A new optional entry called "wps_application_ext" is added to hostapd
config file to configure this. It enodes the payload of the Application
Extension attribute in hexdump format.

Signed-off-by: Veli Demirel <veli.demirel@airties.com>
Signed-off-by: Bilal Hatipoglu <bilal.hatipoglu@airties.com>
2020-01-04 23:39:30 +02:00
Jouni Malinen
8d84c75f7c Allow testing override for GTK/IGTK RSC from AP to STA
The new hostapd gtk_rsc_override and igtk_rsc_override configuration
parameters can be used to set an override value for the RSC that the AP
advertises for STAs for GTK/IGTK. The contents of those parameters is a
hexdump of the RSC in little endian byte order.

This functionality is available only in CONFIG_TESTING_OPTIONS=y builds.
This can be used to verify that stations implement initial RSC
configuration correctly for GTK/ and IGTK.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-01-04 13:05:26 +02:00
Jouni Malinen
ce01804872 Convert the only remaining send_frame() users to send_mlme()
Since send_mlme() now has support for the no_encrypt argument it is
possible to get rid of the remaining send_frame() uses.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-01-03 13:53:42 +02:00
Jouni Malinen
665a3007fb driver: Add no_encrypt argument to send_mlme()
This is in preparation of being able to remove the separate send_frame()
callback.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-01-03 13:53:32 +02:00
Jouni Malinen
3710027463 Make hostapd_drv_send_mlme() more generic
Merge hostapd_drv_send_mlme_csa() functionality into
hostapd_drv_send_mlme() to get a single driver ops handler function for
hostapd. In addition, add a new no_encrypt parameter in preparation for
functionality that is needed to get rid of the separate send_frame()
driver op.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-01-03 13:34:37 +02:00
Jouni Malinen
b3525dc172 P2P Manager: Use send_mlme() instead of send_frame() for Deauthentication
send_frame() is documented to be used for "testing use only" and as
such, it should not have used here for a normal production
functionality. Replace this with use of send_mlme() which is already
used for sending Deauthentication frames in other cases.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-01-03 13:22:32 +02:00
Roy Marples
a8b00423ea BSD: Use struct ip rather than struct iphdr
As we define __FAVOR_BSD use the BSD IP header.
Compile tested on NetBSD, DragonFlyBSD, and Linux.

Signed-off-by: Roy Marples <roy@marples.name>
2020-01-02 19:17:10 +02:00
Jouni Malinen
1ace2f7c09 Drop debug print level for informative debug messages
These are certainly not error conditions, but normal cases for starting
up. Drop the message from ERROR to DEBUG.

Signed-off-by: Jouni Malinen <j@w1.fi>
2020-01-02 18:05:12 +02:00
Jouni Malinen
b0621b083d Call hostapd_allowed_address() directly from handle_probe_req()
ieee802_11_allowed_address() did not really do anything useful for the
call from handle_probe_req(), so replace that with a direct call to
hostapd_allowed_address() and make ieee802_11_allowed_address() a static
function.

Signed-off-by: Jouni Malinen <j@w1.fi>
2019-12-29 23:44:32 +02:00
Michael Braun
963681723f Fix possible memory leak of RADIUS data in handle_auth()
When returning from handle_auth() after ieee802_11_allowed_address()
returned HOSTAPD_ACL_ACCEPT, but before ieee802_11_set_radius_info() has
been called, identity, radius_cui, and psk might not have been consumed.

Fix this by avoiding the need to free these variables at all.

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2019-12-29 23:43:55 +02:00
Michael Braun
d4ceaafc24 Make hostapd_copy_psk_list() non-static
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2019-12-29 23:34:01 +02:00
Michael Braun
29024efd18 Move the RADIUS cached attributes into a struct
This makes it easier to pass these around and to add new attributes.

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2019-12-29 23:33:57 +02:00
Jouni Malinen
3cd4db231a FT: Do not deliver RRB messages locally without matching FT/SSID
For FT protocol to work, the BSSs need to be operating an FT AKM with
the same SSID and mobility domain. The previous commit covered the
mobility domain, this covers the other prerequisites. This reduces
unnecessary load from having to allocate queued messages for interfaces
that cannot have valid data.

Signed-off-by: Jouni Malinen <j@w1.fi>
2019-12-29 20:41:41 +02:00
Jinglin Wang
c133c785df FT: Check mobility domain when sending RRB message to local managed BSS
Fast BSS Transition requires related APs operating in the same mobility
domain. Therefore, we can check whether the local managed BSS is
operating the same mobility domain before sending multicast/unicast
messages to it. This reduces unnecessary load from having to allocate
queued messages for interfaces that cannot have valid data.

Signed-off-by: Jinglin Wang <bryanwang@synology.com>
Signed-off-by: MinHong Wang <minhongw@synology.com>
2019-12-29 20:32:07 +02:00
Jouni Malinen
a422d9b4c2 RRB: More debug prints for local delivery
This makes it easier to figure out how frames are delivered directly
between BSSs operated within a single hostapd process.

Signed-off-by: Jouni Malinen <j@w1.fi>
2019-12-29 20:17:57 +02:00
Jouni Malinen
7b1105afef RRB: Do not reorder locally delivered messages
Add new messages to the end of the l2_oui_queue instead of inserting
them at the beginning so that the dl_list_for_each_safe() iteration in
hostapd_oui_deliver_later() goes through the messages in the same order
they were originally queued.

Signed-off-by: Jouni Malinen <j@w1.fi>
2019-12-29 20:17:57 +02:00
Jinglin Wang
4834c6869d FT: Fix hostapd_wpa_auth_oui_iter() iteration for multicast packets
When using FT wildcard feature, the inter-AP protocol will send
broadcast messages to discover related APs.

For example,
12/6 16:24:43 FT: Send PMK-R1 pull request to remote R0KH address
    ff:ff:ff:ff:ff:ff
12/6 16:24:43 FT: Send out sequence number request to
    ff:ff:ff:ff:ff:ff

If you have multiple interfaces/BSSs in a single hostapd process,
hostapd_wpa_auth_oui_iter() returned 1 after the first interface was
processed. Iteration in for_each_interface() will be stopped since it
gets a non-zero return value from hostapd_wpa_auth_oui_iter().

Even worse, the packet will not be sent to ethernet because
for_each_interface() returns non-zero value. hostapd_wpa_auth_send_oui()
will then return data_len immediately.

To prevent this, hostapd_wpa_auth_oui_iter() should not return 1 after
any successful transmission to other interfaces, if the dst_addr of
packet is a multicast address.

Signed-off-by: Jinglin Wang <bryanwang@synology.com>
Signed-off-by: MinHong Wang <minhongw@synology.com>
2019-12-29 20:09:52 +02:00
Jouni Malinen
974f84bb73 Fix ignore_broadcast_ssid behavior with SSID List and Short SSID List
ignore_broadcast_ssid=1 (or 2) were practically ignored if the Probe
Request frame included the SSID List or Short SSID List elements. Fix
this by requiring exact SSID match whenever ignore_broadcast_ssid is in
use regardless how SSID parameters are set in the Probe Request frame.

Signed-off-by: Jouni Malinen <j@w1.fi>
2019-12-28 23:19:44 +02:00
Andrei Otcheretianski
1c7f652f9e AP: Support Short SSID List element in Probe Request frames
According to IEEE P802.11ax/D6.0, 11.1.4.3.4 (Criteria for sending a
response), AP should answer Probe Request frames if either SSID or Short
SSID matches. Implement this part of the Short SSID use for the BSS (the
collocated 6 GHz BSS case is not covered in this commit).

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2019-12-28 23:13:58 +02:00
Andrei Otcheretianski
522450b7b1 AP: Determine Short SSID value for the BSS
This can be used in the future to implement support for RNR and scanning
extensions using a shorter field for the SSID.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2019-12-28 22:32:14 +02:00
Zefir Kurtisi
ef48f1bfb3 Ensure authenticator session timer is applied with wired driver
We use the wired driver for wired port authentication with a slight
extension to add the port into a bridge upon successful authentication
and to remove it from the bridge when the session terminates.

Our expectation was that the Session-Timeout configuration at the RADIUS
server is respected, i.e. the session is terminated and would need
re-authentication - like it is working for WLAN sessions over the
nl80211 driver. Alas, it turned out the session is not terminated with
the wired driver.

It turned out that when ap_handle_session_timer() is executed, the
sta->flags of the wired port has only the WLAN_STA_AUTHORIZED bit set.
The WLAN_STA_AUTH bit, which is used to check whether the STA needs to
be de-authenticated, is missing.

Extend the check for any of the WLAN_STA_(AUTH | ASSOC | AUTHORIZED)
bits to solve this issue with the wired driver. That should not have any
side-effect for the WLAN cases since WLAN_STA_AUTH is expected to always
be set for those when there is an ongoing session and separate checks
for ASSOC and AUTHORIZED don't change this.

Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
2019-12-28 20:50:05 +02:00
Ben Greear
ee48f48ba1 hostapd: Support showing neighbor list through hostapd_cli
This lets one know the current neighbor list, and could be used
to populate the neighbor list of other hostapd processes.

For instance:

$ hostapd_cli -i vap0001 show_neighbor
04:f0:21:1e:ae:b0 ssid=04f0211eaeb0af190000802809 nr=04f0211eaeb0af1900008028090603022a00
$ hostapd_cli -i vap0000 set_neighbor 04:f0:21:1e:ae:b0 ssid=04f0211eaeb0af190000802809 nr=04f0211eaeb0af1900008028090603022a00
OK
$ hostapd_cli -i vap0000 show_neighbor
04:f0:21:1e:ae:b0 ssid=04f0211eaeb0af190000802809 nr=04f0211eaeb0af1900008028090603022a00
04:f0:21:c3:b2:b0 ssid=04f021c3b2b0af190000802809 nr=04f021c3b2b0af1900008028090603022a00

Signed-off-by: Ben Greear <greearb@candelatech.com>
2019-12-26 17:59:03 +02:00
Bilal Hatipoglu
b1b62a1364 WPS: Add WPS-PIN-ACTIVE and WPS-CANCEL events
WPS_EVENT_CANCEL is added to indicate cancellation of a WPS operation
for any reason in hostapd/wpa_supplicant.

WPS_EVENT_PIN_ACTIVE is added to indicate when a PIN operation is
triggered in wpa_supplicant.

Signed-off-by: Veli Demirel <veli.demirel@airties.com>
Signed-off-by: Bilal Hatipoglu <bilal.hatipoglu@airties.com>
2019-12-25 20:58:52 +02:00
Mikael Kanstrup
307cfc3286 Strip trailing zero data in EAPOL-Key msg 1/4 when no PMKID to send
EAPOL-Key message 1/4 without PMKID KDE was sent with 22 bytes of stray
data following a zero length key data field. These 22 bytes happens to
be the exact size of an PMKID KDE. Strip these trailing bytes by
checking whether a PMKID is available and adjust pmkid_len to 0 if not.

This was seen for example in capture files created by hwsim test case
suite_b_192 but code modified to handle also the other cases without
PMKID (Suite B no-KCK, FILS without PMKID available, SAE without PMKID
available).

Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sony.com>
2019-12-23 00:26:07 +02:00
Vamsi Krishna
e5620bf025 6 GHz: Select channel width using configured op_class
Use op_class to derive channel width for the operating channel when
op_class is configured by the user in both fixed channel and ACS cases.
We can avoid using ht_capab field to derive channel width especially in
the 6 GHz band in which only HE is supported.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-20 13:38:05 +02:00
Ankita Bajaj
da8570f4c9 Allow non-PCS 6 GHz channels to be excluded from ACS
Add support to exclude non-PSC 6 GHz channels from the input frequency
list to ACS. The new acs_exclude_6ghz_non_psc=1 parameter can be used by
6 GHz only APs.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-20 13:23:13 +02:00
Ankita Bajaj
59bb72642a Allow ACS channel list to be configured as frequencies (in MHz)
The channel numbers are duplicated between 2.4 GHz / 5 GHz bands and 6
GHz band. Hence, add support to configure a list of frequencies to ACS
(freqlist) instead of a list of channel numbers (chanlist). Also, both 5
GHz and 6 GHz channels are referred by HOSTAPD_MODE_IEEE80211A. The 6
GHz channels alone can be configured by using both mode and frequency
list.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-20 13:19:52 +02:00
Ankita Bajaj
5f9b4afdfa Use frequency in HT/VHT validation steps done before starting AP
Using the channel parameter for validating allowed channel combinations
is not scalable to add 6 GHz support in the future since channel numbers
are duplicated between 2.4 GHz / 5 GHz bands and 6 GHz band. Hence use
frequency field for all channel combination validation steps done before
starting AP.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-20 13:05:39 +02:00
Ankita Bajaj
59e33b4a98 ACS: Select current hw_mode based on the selected frequency
After receiving ACS offload results, select the current hw_mode based on
the frequency selected by the ACS algorithm. The current hw_mode will be
further used during other validation steps such as HT capability
validations, DFS validation, etc.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-20 12:45:03 +02:00
Ankita Bajaj
bb781c763f AP: Populate iface->freq before starting AP
Using channel field while starting AP will cause issues with the new
6GHz band as the channel numbers are duplicated between the different
bands. Populate iface->freq before starting AP so that it can be used
instead of the channel number for all validations that need to be done
while starting AP.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-20 12:42:47 +02:00
Ankita Bajaj
41cac481a8 ACS: Use frequency params in ACS (offload) completed event interface
Replace channel fields with frequency fields in ACS completed event
interface from the driver layer. Use
QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_FREQUENCY and
QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_FREQUENCY attributes if the driver
includes them in the QCA_NL80211_VENDOR_SUBCMD_DO_ACS event, otherwise
use QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL and
QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL attributes to maintain
backwards compatibility with old drivers.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-20 12:31:01 +02:00
Ankita Bajaj
840532aea5 Search through all hw_features sets in hw_get_channel_freq()
The 5 GHz channels are stored in one hw_features set with mode
HOSTAPD_MODE_IEEE80211A while the 6 GHz channels will need to stored in
a separate hw_features set (but with same mode HOSTAPD_MODE_IEEE80211A)
due to possibility of different HE capabilities being available between
the 5 GHz and 6 GHz bands.

Search through all hw_features sets whose mode is same as the input mode
while finding channel corresponding to the input frequency in
hw_get_channel_freq().

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-20 12:21:45 +02:00
Ankita Bajaj
15d3568739 ACS: Add channels from all modes matching with configured hw mode
The 5 GHz channels are stored in one hw_features set with mode
HOSTAPD_MODE_IEEE80211A while the 6 GHz channels will need to stored in
a separate hw_features set (but with same mode HOSTAPD_MODE_IEEE80211A)
due to possibility of different HE capabilities being available between
the 5 GHz and 6 GHz bands.

Iterate through all hw_features sets and populate channels from all
hw_features sets whose hardware mode is matching the configured hardware
mode while preparing the channel list for ACS.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-20 12:21:41 +02:00
Jouni Malinen
5a563a3d34 Avoid compiler warning on shadowing a local variable
Fixes: 7fde39fb1a ("Add sae_rejected_groups to hostapd STA control interface command")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-18 13:46:59 +02:00
Jouni Malinen
7fde39fb1a Add sae_rejected_groups to hostapd STA control interface command
This is mainly for testing purposes to be able to check which groups
a STA reports as having been rejected when using SAE H2E.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-12 23:52:36 +02:00
Jouni Malinen
7404574458 DPP: Replace ap boolean with netRole enum in Configurator params
The netRole enum is more generic and can be extended to include new
roles (e.g., Configurator) more easily.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-12 02:33:00 +02:00
Jouni Malinen
f2c4b44b40 SAE H2E: RSNXE override in EAPOL-Key msg 3/4
This new hostapd configuration parameter rsnxe_override_eapol=<hexdump>
can be used to override RSNXE value in EAPOL-Key msg 3/4 for testing
purposes.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-07 17:32:17 +02:00
Jouni Malinen
a889e9a70c SAE: Reject invalid rejected group report in SAE commit explicitly (AP)
Previously, this case was ignored silently in AP mode. While that could
be a reasonable approach for an unexpected condition, it would be fine
to reject this case explicitly as well. This makes it somewhat easier to
test unexpected SAE H2E vs. looping behavior.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-07 00:39:46 +02:00
Jouni Malinen
c88e01e1b6 SAE H2E: Fix validation of rejected groups list
check_sae_rejected_groups() returns 1, not -1, in case an enabled group
is rejected. The previous check for < 0 could not have ever triggered.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-07 00:28:13 +02:00
Jouni Malinen
918df2227e SAE: Reject unexpected Status Code in SAE commit explicitly (AP)
Previously, this case was ignored silently in AP mode. While that could
be a reasonable approach for an unexpected condition, it would be fine
to reject this case explicitly as well. This makes it somewhat easier to
test unexpected SAE H2E vs. looping behavior.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-06 17:26:57 +02:00
Ankita Bajaj
23acdd9f33 Fix memory leak in ACS offload operation
freq_list is built in allocated heap memory and it needs to be freed
before returning from this function.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-05 18:02:46 +02:00
Ankita Bajaj
e86ba912aa ACS: Remove redundant ch_list parameters from do_acs interface
Clean up do_acs interface to not pass ch_list to drivers as the same
information is available in freq_list. The channel numbers are
duplicated between 2.4 GHz and 5 GHz bands and the 6 GHz band. So, use
the QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST to populate only 2.4 GHz and 5 GHz
channels to ensure backwards compatibility with old drivers which do not
have support to decode the newer QCA_WLAN_VENDOR_ATTR_ACS_FREQ_LIST
attribute.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-05 18:02:34 +02:00
Ankita Bajaj
3cf360b8e2 DFS: Don't handle DFS ops for 6 GHz channels
Skip DFS checks and CAC operation for 6 GHz channels. AFC checks
will be added for 6 GHz channels later.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-05 17:12:27 +02:00
Ankita Bajaj
ee0030e814 6 GHz: Do not check for HT capability on 6 GHz channels
HT capability check is not required when starting AP on 6 GHz band as
only HE operation mode is allowed in the 6 GHz band.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-05 17:12:27 +02:00
Jouni Malinen
e780b4bf20 DPP: Bootstrapping via NFC URI Record
This extends hostapd and wpa_supplicant DPP implementation to allow the
bootstrapping URI to be generated for and parsed from an NFC Tag with an
NFC URI Record. This is similar to the way the bootstrapping URI is used
with QR Code for unidirectional authentication.

The DPP_BOOTSTRAP_GEN command uses "type=nfc-uri" to request the URI to
be assigned for NFC URI Record. In practice, the URI is generated
identically to the QR Code case, but the internal entry maintains the
NFC-URI type.

A new command "DPP_NFC_URI <uri>" can now be used to parse the URI read
from an NFC Tag with the NFC URI Record. This is similar to the
DPP_QR_CODE command.

Other commands (mainly, DPP_LISTEN and DPP_AUTH_INIT) are used for NFC
URI in the same way as they are used for QR Code.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-05 12:37:51 +02:00
Hu Wang
38203148e9 Extend hostapd to support setband to driver via QCA vendor command
Commit 844dfeb804 ("QCA vendor command support to set band to driver")
added a vendor command to pass 'SET setband' command information to the
driver in wpa_supplicant. Add similar changes to hostapd control
interface.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-12-02 15:55:43 +02:00
Jouni Malinen
9f50538e13 SAE H2E: Do not use sae_h2e param in AP mode if SAE is disabled
Previously, nonzero sae_h2e parameter values were used to perform SAE
H2E specific operations (deriving PT, adding RSNXE, adding H2E-only BSS
membership selector) in AP mode even if SAE was not enabled for the
network. This could result in unexpected behavior if sae_pwe=1 or
sae_pwe=2 were set in the configuration. Fix this by making the SAE
operations conditional on SAE being actually enabled.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-11-29 00:07:57 +02:00
Jouni Malinen
5b50265e13 WMM: Do not modify input TSPEC buffer during processing
The WMM TSPEC processor used the input buffer for processing the request
and building the response. This was fine for the FT case, but for the
WMM Action frame case, the input buffer is marked const, so it should
not really be modified. This modification could not really cause any
noticeable harm, but it can result in error reports from fuzzing and
potentially even from some static analyzers.

Fix this by marking the input arguments const more consistently (the
parsed IE was able to drop the const) and copy the const input data to a
temporary buffer for processing and modification instead of allowing the
input data to be modified.

Credit to OSS-Fuzz: https://bugs.chromium.org/p/oss-fuzz/issues/detail?id=19050
Signed-off-by: Jouni Malinen <j@w1.fi>
2019-11-23 17:39:55 +02:00
Lei Wang
530b8ee3c8 hostapd: Update DFS status in VHT80+80 mode
Update center frequency and center frequency2's DFS channel status in
VHT80+80 mode. Otherwise it will cause AP failed to start on a DFS
channel.

Tested: qca9984 with firmware ver 10.4-3.10-00047

Signed-off-by: Rick Wu <rwu@codeaurora.org>
Signed-off-by: Lei Wang <leiwa@codeaurora.org>
2019-11-10 22:54:19 +02:00
Jouni Malinen
93ba13bcfd Fix status code in SAE/DPP association PMKID mismatch (driver-AP-SME)
wpa_validate_wpa_ie() was already extended to cover these cases with
WPA_INVALID_PMKID return value, but hostapd_notif_assoc() did not have
code for mapping this into the appropriate status code
(STATUS_INVALID_PMKID) and ended up using the default
(WLAN_STATUS_INVALID_IE) instead. This caused AP SME-in-driver cases
returning incorrect status code when the AP did not have a matching
PMKSA cache entry. This could result in unexpected station behavior
where the station could continue trying to use a PMKSA cache entry that
the AP does not have and not being able to recover this.

Fix this by adding the previously missed mapping of validation errors to
status/reason codes.

Fixes: 567da5bbd0 ("DPP: Add new AKM")
Fixes: 458d8984de ("SAE: Reject request with mismatching PMKID (no PMKSA cache entry)")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-11-09 00:33:58 +02:00
Shiva Sankar Gajula
df3b2e22a0 nl80211: Add STA node details in AP through QCA vendor subcommand
Addi STA node details in AP through QCA vendor subcommand
QCA_NL80211_VENDOR_SUBCMD_ADD_STA_NODE vendor when processing FT
protocol roaming.

Signed-off-by: Shiva Sankar Gajula <sgajula@codeaurora.org>
2019-10-25 19:29:53 +03:00
Jouni Malinen
93a1e275a7 SAE: Determine H2E vs. looping when restarting SAE auth in AP mode
If hostapd had existing STA SAE state, e.g., from a previously completed
SAE authentication, a new start of a separate SAE authentication (i.e.,
receiving of a new SAE commit) ended up using some of the previous
state. This is problematic for determining whether to H2E vs. looping
since the STA is allowed (even if not really expected to) to change
between these two alternatives. This could result in trying to use H2E
when STA was using looping to derive PWE and that would result in SAE
confirm failing.

Fix this by determining whether to use H2E or looping for the restarted
authentication based on the Status Code in the new SAE commit message
instead of previously cached state information.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-10-25 19:29:53 +03:00
Pradeep Kumar Chitrapu
327d09aa03 HE: Add 11ax info to ap mode ctrl iface STATUS command
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
2019-10-25 19:29:53 +03:00
Jouni Malinen
d7678a0842 Fix AP Extended Capability length determination
The IE minimum length determination in hostapd_eid_ext_capab() was not
fully up to date with the hostapd_ext_capab_byte() conditions. This
could result in omitting some of the capability octets depending on
configuration. Fix this by adding the missing conditions.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2019-10-25 16:03:37 +03:00