Include the start of the next EAP method in an EAP Payload TLV in the
same message with the Crypto-Binding TLV for the previous EAP method to
get rid of one roundtrip when using more than a single EAP
authentication method within the tunnel. The previous, not optimized,
sequence can still be used with eap_teap_method_sequence=1 for more
complete testing coverage.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
When using the optimized EAP method sequence within the tunnel, crypto
binding for the previous EAP method can be performed in the same message
with the start of the next EAP method. The Crypto-Binding TLV needs to
be processed before moving to the next EAP method for IMSK to be derived
correctly, so swap the order of these processing steps.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
While RFC 7170 does not describe this, EAP-TEAP has been deployed with
implementations that use the EAP-FAST-MSCHAPv2, instead of the
EAP-MSCHAPv2, way of deriving the MSK for IMSK. Use that design here to
interoperate with other implementations since that seems to be direction
that IETF EMU WG is likely to go with an RFC 7170 update.
This breaks interoperability with earlier hostapd/wpa_supplicant
versions.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
EAP-FAST uses a special variant of EAP-MSHCAPv2 called EAP-FAST-MSCHAPv2
in RFC 5422. The only difference between that and EAP-MSCHAPv2 is in how
the MSK is derived. While this was supposed to be specific to EAP-FAST,
the same design has ended up getting deployed with EAP-TEAP as well.
Move this special handling into EAP-MSCHAPv2 implementation so that it
can be shared for both needs.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
With the UHB enabled, the number of scanned frequencies may exceed
the buffer size. Increase it.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add support to consider EHT rates while calculating the estimated
throughput for scan results.
- The estimated EHT throughput uses the HE 0.8 usec GI rates from the
relevant EHT-MCS tables from IEEE P802.11be/D2.0, 36.5.
- The minimum SNR values for EHT rates (4096-QAM) are derived by adding
the existing minimum SNR values of 1024-QAM rates from HE tables and
the difference between the values of minimum sensitivity levels of
1024-QAM rates and 4096-QAM rates defined in Table 36-67 (Receiver
minimum input level sensitivity) in IEEE P802.11be/D2.0.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The arguments were swapped. Apparently all the calls to this function
use the same value for both input and output parameters, so it went
unnoticed. Fix it.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This is needed to be able to drop the OpenSSL security level, if
necessary, for cases where old certificates (e.g., something using SHA-1
signatures) are still needed. openssl_ciphers="DEFAULT@SECLEVEL=0" can
achieve this, but only if applied before attempting to load the
certificates.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Even if the use of H2E isn't strictly mandatory when using SAE on 6 GHz,
WPA3-Personal pushes it on 6 GHz. So lets automatically enable it by
setting sae_pwe=2. This will allow both the hunting-and-pecking and
hash-to-element to work (and be backward compatible).
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
The system may be interested in knowing which bootstrap information
entries are being exercised. This could be used for statistics or
completion signaling to upper application layer outside of hostapd,
along with the public key hash.
Signed-off-by: Michal Kazior <michal@plume.com>
Just like with WPA-PSK and keyids it may be desired to identify
connecting clients to provide additional network filtering.
This does:
- extend DPP_EVENT_AUTH_SUCCESS to expose public
key hash of the peer so the system can pick it
up and use for identification later
- store public key hash in PMKSA from DPP Network
Intro for later use
- extend sta mib to print out the dpp_pkhash
from PMKSA if present
- extend AP_STA_CONNECTED to include the
dpp_pkhash from PMKSA if present
Signed-off-by: Michal Kazior <michal@plume.com>
This event is generated in a couple of places. It'll be easier to extend
the event with additional metadata if it's generated in a single place.
Signed-off-by: Michal Kazior <michal@plume.com>
When considering a channel for a bandwidth of 40/80/160 MHZ on the 5 GHz
or 6 GHz band, allow selecting one of the other channels in the segment
instead of the first one. This is done only if the other channel's
interference_factor is lower than the first one's.
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
When using 40/80/160 MHz bandwidth on the 5 GHz or 6 GHz band, enforce
the secondary channel to be the other channel of the corresponding 40
MHz segment.
Even if this is useless for now, this is preparatory work to allow ACS
to select a primary channel which is not the first of its segment.
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
When using 40/80/160 MHz bandwidth, instead of computing the index of
the segment center freq based on the selected channel, lets look it up
in the bw_desc[] table.
This is preparative work to allow selecting a primary channel which is
not the first of the segment.
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
This extracts the 3 lists of allowed channels for 40/80/160 MHz
bandwidth out of their respective functions. It also adds for each
segment the frequency of the segment's last channel and the index of the
segment's "center" channel.
This is preparative work to allow selecting a channel which is not the
first of its segment for 40/80/160 MHz. In addition, this adds the 5 GHz
160 MHz channel defined for 5735-5895 MHz (channels 149-177).
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
Instead of opening a new TCP connection for each received Presence
Announcement from the same Enrollee from the Relay to the Controller,
use an existing connection if it is still waiting for Authentication
Response. This avoids opening multiple parallel sessions between the
same Controller and Enrollee.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
If wpa_supplicant receives a duplicate DPP chirp over a TCP connection
this causes the connection (and all of its state) to be torn down.
Such a tear-down means that the authentication request state is discarded.
That in turn will cause any otherwise valid authentication response
to not succeed.
This commit addresses that problem. It also does not attempt to check
for duplicates until at least we know that we have an appropriate hash.
Signed-off-by: Eliot Lear <lear@lear.ch>
Add a callback handler to notify details of a PMKSA cache entry when it
is added to the PMKSA cache. This can be used to provide external
components more convenient access to the PMKSA cache contents.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
When using multiple BSSes on a single radio, it is sometimes desirable
to reconfigure one BSS, without disconnecting the stations already
connected to other BSSes on the same radio.
When a BSS is reconfigured using the SET command, there is no "old"
configuration we can compare to (so we cannot compare a hash of the
configuration for example).
One possible solution would be to make the current RELOAD command
reload only the current BSS. However, that could break the workflow of
existing users. Instead, introduce a new RELOAD_BSS command, which
reloads only the current BSS.
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
In hostapd_clear_old() multiple steps are needed to clear a BSS.
There are some places where it would be desirable to clear only some
BSSes and not all.
To make it easier to clear only some BSSes, split hostapd_clear_old()
with hostapd_clear_old_bss(), which does the same actions but on a
single BSS.
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
When using MAC randomization wpa_supplicant can change the local MAC
address during roaming scenario:
1. We attach to AP1 (with MAC1/SSID1).
2. Roaming to AP2 (with MAC2/SSID2) is started:
a) we send DEAUTH(for AP1, with MAC1)
b) we change MAC to MAC2 due to randomization
c) we start authentication for AP2
d) we get notification about DEAUTH for AP1 (which we ignore)
e) we complete association with AP2
In point 2d we completely ignore the notification which later causes
problems. This happens if the deauthentication event is generated by the
local driver (e.g., due to beacon loss) instead of AP2 sending an
explicit Deauthentication frame.
The intended behavior is as follows: during roaming we generate DEAUTH
(2a) and signal this event right away. To protect from handling of our
own DEAUTH for the 2nd time supplicant marks 'ignore_next_local_deauth'
variable. In point 2d we should receive this notification and clear the
flag but this does not happen because MAC1 in the notification is not
the current MAC address (it has been changed in 2b) so this notification
is ignored as a one with a "foreign" address.
So we end up successfully at AP2 but with 'ignore_next_local_deauth'
still set which causes problems. For example if AP2 shuts down it has
been observed on some drivers that the DEAUTH notification is generated
as a local one and since we have flag to ignore it nothing is reported
over D-Bus.
To address the problem let's store the previously used MAC address and
use it for checking for foreign address (in combination with the current
one).
Signed-off-by: Andrzej Ostruszka <amo@semihalf.com>
This is a step in separating RSN and WPA(v1) processing of EAPOL-Key
frames into separate functions. This allows the implementation to be
simplified and potentially allows the validation rules to be made
stricter more easily. This is also a step towards allowing WPA(v1)
functionality to be removed from the build in the future.
Signed-off-by: Jouni Malinen <j@w1.fi>
The default provider is being loaded here explicitly only because
OSSL_PROVIDER_load() disables the fallback provider loading (on either
success or failure). If the legacy provider fails to load, which it may
in some configurations, it will never load the default provider.
Just use the formulation which attempts to load without changing the
fallback behavior.
"default" will still be/only be loaded if no other provider (notably
FIPS) is loaded to provide algorithms.
Signed-off-by: Norman Hamer <nhamer@absolute.com>
DES and RC4 are not allowed in such builds, so comment out des_encrypt()
and rc4_skip() from the build to force compile time failures for cases
that cannot be supported instead of failing the operations at runtime.
This makes it easier to detect and fix accidental cases where DES/RC4
could still be used in some older protocols.
Signed-off-by: Norman Hamer <nhamer@absolute.com>
CONFIG_NO_RC4=y could have been used to remove this functionality, but
it might as well be done automatically based on CONFIG_FIPS=y as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
PMKSA caching for the FT initial mobility domain association was fully
defined in IEEE Std 802.11-2020. The state before that was unclear and
there has been interoperability issues in this area, so use of PMKSA
caching with FT-EAP has been disabled in wpa_supplicant by default.
The wpa_supplicant and hostapd implementation of PMKSA caching for FT
ended up using an earlier default mechanism (SHA-1) for deriving the
PMKID when using the FT-EAP. This does not match what got defined in
IEEE Std 802.11-2020, 12.11.2.5.2 (SHA256). It is not really desirable
to use SHA-1 for anything with FT since the initial design of FT was
based on SHA256. Furthermore, it is obviously not good to differ in
behavior against the updated standard. As such, there is sufficient
justification to change the implementation to use SHA256 here even
though this ends up breaking backwards compatibility for PMKSA caching
with FT-EAP.
As noted above, this is still disabled in wpa_supplicant by default and
this change results in PMKSA caching not working only in cases where it
has been enabled explicitly with ft_eap_pmksa_caching=1. Those cases
recover by falling back to full EAP authentication.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add QCA_WLAN_VENDOR_ATTR_CONFIG_WFC_STATE vendor attribute. Userspace
uses this attribute to configure wfc state to the driver/firmware. The
driver/firmware uses this information to optimize power savings, rate
adaption, roaming, etc.
Signed-off-by: Mukul Sharma <quic_mukul@quicinc.com>
IEEE Std 802.11-2020, 12.4.7.6 says that status code CHALLENGE_FAILURE,
needs to be sent in case the verification action fails for SAE Confirm
message frame from a STA: "An SAE Confirm message, with a status code
not equal to SUCCESS, shall indicate that a peer rejects a previously
sent SAE Confirm message. An SAE Confirm message that was not
successfully verified is indicated with a status code of
CHALLENGE_FAILURE."
hostapd, however, did not use this status code for this case. In
ieee802_11.c the function sae_check_confirm() is called and in case of
verification failure (-1 is returned), the response is set to
WLAN_STATUS_UNSPECIFIED_FAILURE (status code = 1). Fix this to use
CHALLENGE_FAILURE.
Signed-off-by: Koen Van Oost <koen.vanoost@airties.com>
Signed-off-by: Mert Ekren <mert.ekren@airties.com>
Explicitly check for invalid cases where the configured channel and
bandwidth might result in the full channel number range going beyond the
list of supported channels to avoid reading beyond the end of the
channel buffer.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The SA/DA checks needs to be reversed for the TX case.
Fixes: 8481c750 ("PASN: Fix Authentication frame checks")
Signed-off-by: Vinay Gannevaram <quic_vganneva@quicinc.com>
If an AP is started on a DFS channel (or any channels within its
bandwidth require DFS) and DFS is offloaded to the driver, hostapd needs
to wait for CAC to complete. But the driver may not do CAC and just
switches to a non-DFS channel instead. This would result in a failure to
start the AP because hostapd fails to receive a CAC complete event and
cannot finish interface setup.
Skip CAC and complete AP setup in the channel switch event handler for
this case.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add CLOSE_LOG command to stop hostapd logging to file. This can be
followed with RELOG to restart logging to the same file path.
Signed-off-by: Sai Pratyusha Magam <quic_smagam@quicinc.com>
Add a new subcommand QCA_NL80211_VENDOR_SUBCMD_DOZED_AP to configure
doze mode state on an AP interface. This is also used as an event to
indicate the updated configuration. In doze mode, AP transmits
beacons at higher beacon intervals and RX is disabled.
Uses attributes defined in enum qca_wlan_vendor_attr_dozed_ap.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
During the roam scan, if there are no desired APs found in the partial
frequency list, an immediate full scan on all the supported frequencies
is initiated as a fallback. This would include the 6 GHz PSC
frequencies. Define an attribute to allow that behavior to be modified
to include PSCs only if 6 GHz use has been detected.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
When the RADIUS server requests a STA to be deauthenticated imminently
without providing a reason URL, there is no need to allow the STA spend
any additional time associated. Deauthenticate the STA immediately after
it has ACK'ed the WNM-Notification frame indicating imminent
deauthentication or at latest two seconds after having processes the
Access-Accept message.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Currently sta_mlo_info.req_links is not getting cleared before
populating the requested links information for a new connection/roam
event. This is causing wrong requested links bitmap in
sta_mlo_info.req_links if there is a change in requested link IDs
between the previous and the new connection. To avoid such issues fully
clear MLO connection information after disconnection and before
populating MLO connection information during (re)association event.
Fixes: cc2236299f ("nl80211: Get all requested MLO links information from (re)association events")
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
IGTK and BIGTK MLO KDEs should be validated only when the AP sends them
in EAPOL-Key msg 3/4. Though IEEE P802.11be/D2.2 mandates MLO AP to
enable PMF and Beacon Protection features there is no text to mandate a
STA to discard connection when the MLO AP doesn't send IGTK and BIGTK
MLO KDEs in EAPOL-Key msg 3/4 for a link. Also, fix
wpa_sm->mgmt_group_cipher checks before processing MLO IGTK and BIGTK
MLO KDEs.
Fixes: f15cc834cb ("MLD STA: Processing of EAPOL-Key msg 3/4 frame when using MLO")
Fixes: 8f2e493bec ("MLD STA: Validation of MLO KDEs for 4-way handshake EAPOL-Key frames")
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
During the roam scan, if there are no desired APs found in the partial
frequency list, an immediate full scan on all the supported frequencies
is initiated as a fallback. This flag controls the frequency list
creation for full scan on the following lines.
1 - Full scan to exclude the frequencies that were already scanned by
the previous partial scan.
0 - Full scan to include all the supported frequencies irrespective of
the ones already scanned by partial scan.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Taking sizeof(ptr) is incorrect to determine size of passed in hash and
results in hlen getting set to a very large value since MD5_MAC_LEN >
sizeof(ptr). Provide the actual size of the hash buffer from the caller
to fix this.
tls_key_x_server_params_hash() callers src/tls/tlsv1_client_read.c and
src/tls/tlsv1_server_write.c both pass in a large enough hash (hash[64]
or hash[100]) that this does not appear to have an impact, though it is
still wrong.
Signed-off-by: Glenn Strauss <gstrauss@gluelogic.com>
This new value was added to verify peer certificate if it is provided,
but not reject the TLS handshake if no peer certificate is provided.
Signed-off-by: Glenn Strauss <gstrauss@gluelogic.com>
The dev pointer could potentially be NULL here in some P2PS cases, so
check it explicitly before dereferencing it when checking for 6 GHz
capability.
Fixes: b9e2826b9d ("P2P: Filter 6 GHz channels if peer doesn't support them")
Signed-off-by: Jouni Malinen <j@w1.fi>
Try to make the bounds checking easier for static analyzers by checking
each length field separately in addition to checking them all in the end
against the total buffer length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Try to avoid static analyzer warnings due to use of the FTE length
field instead of the separately stored and validated length field value
when deriving FTE MIC.
Signed-off-by: Jouni Malinen <j@w1.fi>
Try to avoid static analyzer warnings due to use of the RSNE length
field instead of the separately stored and validated length field value
when deriving FTE MIC.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 25b52e5f83 ("FT: Extend FTE parsing for FT-SAE-EXT-KEY") used
possible MIC length iteration to try to figure out the length of the MIC
field in FTE. That was the only option available at the time, but FTE is
now being extended in IEEE 802.11-REVme to explicitly indicate the
length of the MIC field for the new FT-SAE-EXT-KEY AKM to make this
easier.
Use the new design from the approved comment resolution (*) in
REVme/D2.0 ballot CID 3135 to simplify implementation. This gets rid of
the need to pass in key length and the somewhat strange need_{r0kh,r1kh}
parameters to wpa_ft_parse_ies().
(*)
https://mentor.ieee.org/802.11/dcn/22/11-22-1991-02-000m-proposed-resolutions-to-some-lb270-comments.docx
Signed-off-by: Jouni Malinen <j@w1.fi>
This is needed to avoid trying the subsequent connections with the old
PMKID that the AP claims not to hold and continues connection failures.
This was already handled for the SME-in-the-driver case in commit commit
50b77f50e8 ("DPP: Flush PMKSA if an assoc reject without timeout is
received"), but the wpa_supplicant SME case did not have matching
processing.
Add the needed check to avoid recover from cases where the AP has
dropped its PMKSA cache entry. Do this only based on the specific status
code value (53 = invalid PMKID) and only for the PMKSA entry that
triggered this failure to minimize actions taken based on an unprotected
(Re)Association Response frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
The addition of the "spa" argument was missed in the empty inline
function.
Fixes: 9ff778fa4b ("Check for own address (SPA) match when finding PMKSA entries")
Signed-off-by: Jouni Malinen <j@w1.fi>
Depending on the crypto library, crypto_ec_point_from_bin() can fail if
the element is not on curve, i.e., that error may show up before getting
to the explicit crypto_ec_point_is_on_curve() check. Add a debug print
for that earlier call so that the debug log is clearly identifying
reason for rejecting the SAE commit message.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This prevents attempts of trying to use PMKSA caching when the existing
entry was created using a different MAC address than the one that is
currently being used. This avoids exposing the longer term PMKID value
when using random MAC addresses for connections.
In practice, similar restriction was already done by flushing the PMKSA
cache entries whenever wpas_update_random_addr() changed the local
address or when the interface was marked down (e.g., for an external
operation to change the MAC address).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is needed to be able to determine whether a PMKSA cache entry is
valid when using changing MAC addresses. This could also be used to
implement a mechanism to restore a previously used MAC address instead
of a new random MAC address.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Using separate variables for BSSID and peer address is needed to support
Wi-Fi Aware (NAN) use cases where the group address is used as the BSSID
and that could be different from any other peer address. The
infrastructure BSS cases will continue to use the AP's BSSID as both the
peer address and BSSID for the PASN exchanges.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Rename struct pasn_data::bssid to peer_addr to be better aligned with
different use cases of PASN and its extensions. This is a step towards
having option to use different peer address and BSSID values for NAN use
cases.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Kernel commit 22e76844c566 - ("ieee80211: Increase PMK maximum length to
64 bytes") increased the maximum allowed length for NL80211_ATTR_PMK to
64 bytes. Thus, allow sending 64 bytes PMK in NL80211_CMD_SET_PMKSA and
if NL80211_CMD_SET_PMKSA fails with ERANGE try NL80211_CMD_SET_PMKSA
again without PMK. Also, skip sending PMK when PMK length is greater
than 64 bytes.
This is needed for some newer cases like DPP with NIST P-521 and
SAE-EXT-KEY with group 21. The kernel change from 48 to 64 octets is
from February 2018, so the new limit should be available in most cases
that might want to use these new mechanisms. Maintain a backwards
compatible fallback option for now to cover some earlier needs for DPP.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
wpa_supplicant has support for only a single FT key hierarchy and as
such, cannot use more than a single mobility domain at a time. Do not
allow FT protocol to be started if there is a request to reassociate to
a different BSS within the same ESS if that BSS is in a different
mobility domain. This results in the initial mobility domain association
being used whenever moving to another mobility domain.
While it would be possible to add support for multiple FT key hierachies
and multiple mobility domains in theory, there does not yet seem to be
sufficient justification to add the complexity needed for that due to
limited, if any, deployment of such networks. As such, it is simplest to
just prevent these attempts for now and start with a clean initial
mobility domain association.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
There is no help from seeing 32 lines of debug prints about clearing
AP's RSNE/RSNXE information for each potential link when such
information has not been set in the first place. These were printed even
when there is no use of MLO whatsoever, so get rid of the prints for any
case where the value has not yet been set.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Wi-Fi Alliance specification for Automated Frequency Coordination (AFC)
system ensures that the Standard Power Wi-Fi devices can operate in 6
GHz spectrum under favorable conditions, without any interference with
the incumbent devices.
Add support for vendor command/events and corresponding
attributes to define the interface for exchanging AFC requests and
responses between the driver and a userspace application.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Commit 820211245b ("OpenSSL: Fix HPKE in some corner cases") increased
the buffer size for EVP_PKEY_derive() by 16 octets, but it turns out
that OpenSSL might need significantly more room in some cases. Replace a
fixed length buffer with dynamic query for the maximum size and
allocated buffer to cover that need.
This showed up using the following test case sequence:
dbus_pkcs11 module_wpa_supplicant
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The length of labeled_info is determined separately, so there is no need
to increment the pos pointer after the final entry has been added.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Not only the hash[] array, but also the r0_key_data[] array needs to be
extended in size to fit the longer key and salt.
Fixes: a76a314c15 ("FT: Extend PMK-R0 derivation for FT-SAE-EXT-KEY")
Signed-off-by: Jouni Malinen <j@w1.fi>
Add support for group rekeying in MLO connection. Parse per link MLO
GTK/IGTK/BIGTK KDEs from Group Key msg 1/2 and configure to the driver.
Signed-off-by: Rohan Dutta <quic_drohan@quicinc.com>
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Use AP MLD address as the destination address for EAPOL-Key 4-way
handshake frames since authenticator/supplicant operates above MLD. The
driver/firmware will use RA/TA based on the link used for transmitting
the EAPOL frames.
Signed-off-by: Rohan Dutta <quic_drohan@quicinc.com>
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Validate new KDEs defined for MLO connection in EAPOL-Key msg 1/4 and
3/4 and reject the 4-way handshake frames if any of the new KDE data is
not matching expected key data.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Process EAPOL-Key msg 3/4 and configure PTK and per-link GTK/IGTK/BIGTK
keys to the driver when MLO is used.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add support to specify a Link ID for set key operation for MLO
connection. This does not change the existing uses and only provides the
mechanism for extension in following commits.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Configure TK to the driver with AP MLD address with MLO is used. Current
changes are handling only EAPOL-Key 4-way handshake and FILS
authentication cases, i.e., FT protocol case needs to be addressed
separately.
Signed-off-by: Rohan Dutta <quic_drohan@quicinc.com>
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Use the AP MLD address instead of the BSSID of a link as the
authenticator address in the PMKSA entry.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Use AP MLD address to derive pairwise keys for MLO connection. Current
changes are handling only PTK derivation during EAPOL-Key 4-way
handshake and FILS authentication, i.e., FT protocol case needs to be
addressed separately.
Signed-off-by: Rohan Dutta <quic_drohan@quicinc.com>
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add new KDEs introduced for MLO connection as specified in
12.7.2 EAPOL-Key frames, IEEE P802.11be/D2.2.
- Add MAC and MLO Link KDE for each own affliated link (other than the
link on which association happened) in EAPOL-Key msg 2/4.
- Add MAC KDE in 4/4 EAPOL frame.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Update the following MLO connection information to wpa_sm:
- AP MLD address and link ID of the (re)association link.
- Bitmap of requested links and accepted links
- Own link address for each requested link
- AP link address, RSNE and RSNXE for each requested link
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Currently only accepted MLO links information is getting parsed from
(re)association events. Add support to parse all the requested MLO links
information including rejected links. Get the rejected MLO links
information from netlink attributes if the kernel supports indicating
per link status. Otherwise get the rejected MLO links information by
parsing (Re)association Request and Response frame elements.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Make sure the elements were present before trying to parse them. This
was already done for most cases, but be consistent and check each item
explicitly before use.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous version was using typecasting to ignore const marking for
the input buffer to be able to clear the MIC field for MIC calculation.
That is not really appropriate and could result in issues in the future
if the input data cannot be modified. Fix this by using an allocated
copy of the buffer.
Signed-off-by: Jouni Malinen <j@w1.fi>
The way type and subtype of the FC field was checked does not really
work correctly. Fix those to check all bits of the subfields. This does
not really make any practical difference, though, since the caller was
already checking this.
Furthermore, use a helper function to avoid having to maintain two
copies of this same functionality.
Signed-off-by: Jouni Malinen <j@w1.fi>
Document in src/crypto/crypto.h that compressed point format is expected
in DER produced by crypto_ec_key_get_subject_public_key(). This is the
format needed for both SAE-PK and DPP use cases that are the current
users of this function.
Signed-off-by: Glenn Strauss <gstrauss@gluelogic.com>
For the 6 GHz opclass 132, ch for loop only allows non-PSC channels { 1,
9, 17, 25, 33, 41, 49,... } to be used. This does not match the IEEE Std
802.11ax-2021 expectation of a 6 GHz-only AP "should set up the BSS with
a primary 20 MHz channel that coincides with a preferred scanning
channel".
Increase ch by 4 to allow PSC channel to be used for 6 GHz BW40.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
It's necessary to maintain knowledge of the 6 GHz capability of the
peer. Since the Device Capability field migth change between frames
depending on the context in which they are used, loooking at the last
received message might not always provide accurate information.
Add supports_6ghz bool variable in struct p2p_device, initialize it to
false and set to true if the P2P_DEV_CAPAB_6GHZ_BAND_CAPABLE bit is set
to 1 in any P2P frame that includes the P2P Capability attribute. This
boolean would not be cleared to false at any point in time so that the
info doesn't disappear dynamically.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a new vendor subcommand
QCA_NL80211_VENDOR_SUBCMD_MLO_PEER_PRIM_NETDEV_EVENT to send notification
to application layer about primary netdev of an MLO peer association.
Also define the attributes present in this subcommand.
Signed-off-by: Krunalsinh Padhar <quic_kpadhar@quicinc.com>
Introduce a run time roam configuration for "hand off delay for RX".
This value, in milliseconds, will delay the hand off for the specified
time to receive pending RX frames from the current BSS.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
libpasn.so users, e.g., Wi-Fi Aware module, could use this function
while deriving protocol specific keys using KDK. Move this function to
global scope to allow that.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
struct wpas_pasn is common to both initiator and responder, so rename it
to pasn_data to avoid the "wpas_" prefix that could be seen as a
reference to wpa_supplicant (PASN initiator).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Wi-Fi Aware uses PASN handshake to authenticate peer devices. Devices
can simply verify each other for subsequent sessions as long as the keys
remain valid after authentication has been successful and pairing has
been established.
In pairing verification, Wi-Fi Aware devices uses PASN Authentication
frames with custom PMKID and Wi-Fi Aware R4 specific verification IEs.
It does not use wrapped data in the Authentication frames. This function
provides support to construct PASN Authentication frames for pairing
verification.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Make it clear that this argument is not modified and freed within PASN
processing to be consistent with the only use of it by calling
wpas_pasn_build_auth_1() which has already marked it const.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Wi-Fi Aware defines protocol specific elements in PASN Authentication
frames for pairing setup. Add an option to add this type of custom
elements into PASN frames. This is mainly for the libpasn.so use cases.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
PASN responder validates auth 1 frame and sends auth 2 frame to the
initiator. It analyses the auth 3 frame and verifies successful
authentication. Wi-Fi Aware modules can reuse this functionality through
a shared library libpasn.so generated from this code. Move the PASN
functionality that is now decoupled from the hapd context into a
separate file in a common directory to make it easier to build such a
library.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
PASN initiator functionality builds auth 1 and auth 3 frames, and
processes auth 2 frame received from the responder. Wi-Fi Aware modules
can reuse this functionality through a shared library libpasn.so
generated from this code. Move the PASN functionality that is now
decoupled from the wpa_s context into a separate file in a common
directory to make it easier to build such a library.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is helpful in being able to get the functionality needed for SAE
into a separate library (libpasn.so) without needing all of the
ieee802_11.c functionality.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Wi-Fi Aware R4 specification defines Beacon RSNE/RSNXE to be same as
RSNE/RSNXE present in Auth2 frame. So, MIC validation should be done
with the RSNE and RSNXE received in Auth2 frame.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Wi-Fi Aware R4 specification introduces a custom PMKID derived from
Nonce and TAG. This custom PMKID is included in PASN Authentication
frames during pairing verification. So, allow use of a custom PMKID in
PASN frames and validate it using a function handler. Wi-Fi Aware
component that uses libpasn.so should take care of validating the custom
PMKID.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Introduce a function handler to transmit PASN Authentication frames to
the driver. This removes the hapd dependency for sending the frames.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
PTK is stored in the PTKSA cache following a successful PASN handshake,
however AKMP is removed upon a WPA PASN reset. The PASN handshake is
used in the Wi-Fi Aware R4 specification to define the pairing setup
process. KDK is used to generate a new set of keys, while AKMP is
required for key derivation for pairing. So, keep AKMP in the PTKSA
cache.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This makes hostapd use the struct defines from pasn_common.h so that the
same struct is shared with wpa_supplicant.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Make struct wpas_pasn common for both the initiator and the responder by
adding required parameters for responder to the existing struct
wpas_pasn. This makes both hostapd and wpa_supplicant share the same
structure definitions in preparation for allowing PASN functionality to
be built into a separate library.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is a step towards decoupling the PASN initiator and responder
implemenentation is decoupled from the wpa_s and hapd contexts and
moving to a common folder for better abstraction. Move the struct
wpas_pasn definition to a common file for initiator and responder. The
idea is to provide a library libpasn.so from PASN common code. Include
C++ compatibilty wrapper to extend libpasn.so support for modules using
cpp code base.
This library can be used in applications implementing protocols based on
the PASN handshake.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Store PMKSA cache entry in wpas_pasn and remove wpa_sm dependency to add
an entry to PMKSA cache. This is a step towards allowing the PASN
implementation to be used outside the context of wpa_supplicant.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Allow PMKSA caching functionality to be used even if sm, current_cb, and
free_cb are uninitialized. This makes RSN supplicant state machine
independent PMKSA caching possible for other modules, enabling
functional reuse.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This was supposed to update the requested value to the next available
one, not to duplicate the already assigned value.
Fixes: b17b86da47 ("QCA vendor attribute to configure periodic sounding")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a new QCA vendor attribute to configure the periodic sounding
for Tx beamformer functionality.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Need to copy the actual data of the attribute, not the beginning of the
data structure pointing to the attribute.
Fixes: de3b91a172 ("nl80211: Define vendor interface functions to offload PASN authentication")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
AES-WRAP(KEK) protection of the Key Data field did not include all the
details in the log. Extend that to cover the details that were already
present for the AES-SIV case to make the debug log more useful for
analyzing issues in this area. Furthermore, print the full EAPOL-Key
frame in the log.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Define subelement IDs and Per-STA Profile STA control fields of Basic
Multi-Link element as described in IEEE P802.11be/D2.2. Also add define
for Multi-Link Control field length.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Instead of saving the pointers to the fragment elements during parsing
of the frame, append all fragments found right after the element to the
element length. Defragmentation of the element can be done by parsing
appended fragment elements. This approach removes the limit on the
maximum number of fragmented elements supported in a frame.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Parse and store pointers to different types of Multi-Link elements
received in Management frames.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Fetch the MLO association Link ID info from the driver to the
wpa_supplicant instance of the corresponding MLD STA interface. This
info is needed when setting the MLO connection info to wpa_sm.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
NL80211_CMD_CONNECT event indicates MLO links status info with kernel
commit 53ad07e9823b ("wifi: cfg80211: support reporting failed links").
Consider MLO links as valid links only if the status is success (or was
not indicated).
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add support for new vendor sub-command attributes for 320 MHz
channel width and puncturing information as part of the
external ACS.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Introduce a new attribute to configure access category
override for UDP frames of BE/BK category. Unlike, the
earlier attribute QCA_WLAN_VENDOR_ATTR_CONFIG_UDP_QOS_UPGRADE
which will override for all UDP frames, this attribute is
for overriding only for BE/BK based UDP frames.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Figure out the correct hash algorithm based on which MIC field length
assumption results in successful parsing. This is needed since the key
length is not yet known at this point on the AP when using the new
FT-SAE-EXT-KEY AKM.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Provide AKM, key length, and information about needed subelements to the
parser function so that the variable length MIC field cases can be
recognized for FT-SAE-EXT-KEY. Knowledge about R0KH-ID/R1KH-ID being
needed is required to be able to iterate over possible MIC field lengths
for the case where the AP does not yet know the correct key length at
the beginning of FT protocol.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Provide AKM to the helper function so that the new SHA256 and SHA512
options can be covered for FT-SAE-EXT-KEY.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Provide key length instead of SHA384/SHA256 selection to the helper
function so that the new SHA512 option can be covered for
FT-SAE-EXT-KEY.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Provide enough information to allow the FTE to be built using the
correct MIC field length based on the used AKM and key length.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add service class id attribute
QCA_WLAN_VENDOR_ATTR_SCS_RULE_CONFIG_SERVICE_CLASS_ID in SCS rule
configuration vendor subcommand
QCA_NL80211_VENDOR_SUBCMD_SCS_RULE_CONFIG.
Signed-off-by: Harsh Kumar Bijlani<quic_hbijlani@quicinc.com>
Move from this type of constructions:
switch (val) {
case 1:
something;
break;
}
default-action;
into following:
switch (val) {
case 1:
something;
break;
default:
default-action;
break
}
for cases where the switch statement is not expected to contain a full
set of enum values and as such, does not lose value from not having the
default target.
This makes the intent of default behavior clearer for static analyzers like
gcc with -Wswitch-default.
Signed-off-by: Chaoli Zhou <quic_zchaoli@quicinc.com>
Do not include 6 GHz channels in the ACS possible channel list if
neither HE (ieee80211ax=1) nor EHT (ieee80211be=1) is enabled since
those channels cannot be used in such combination.
Signed-off-by: Vishal Miskin <quic_vmiskin@quicinc.com>
Information from both NL80211_CMD_ROAM and
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH events is required for
processing the roam events correctly, especially to get the newly
connected BSS details. Indicate the roam event to private libraries only
after NL80211_CMD_ROAM and QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH
events are received.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Do not try to use variables that are not defined without
CONFIG_IEEE80211R=y and add the forgotten "inline" for the function
wrapper.
Fixes: 5c65ad6c0b ("PASN: Support PASN with FT key derivation")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add support to parse MLO connection information from
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_MLO_LINKS for
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH event.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add support for parsing MLO KDEs as defined in Table 12-10 (KDE
selectors) in IEEE P802.11be/D2.0.
Signed-off-by: Rohan Dutta <quic_drohan@quicinc.com>
Co-authored-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add a new vendor sub-command to implement Spatial Reuse feature.
Userspace enables SR feature with specific configuration parameters. The
driver/firmware upon receiving the command, enables the SR feature if it
is supported by the currently connected AP. The driver may reject the
command if it cannot enable the SR with the configured parameters. The
driver sends events to userspace to indicate when SR feature is enabled
or disabled internally. Userspace can also query SR feature related
parameters and statistics from the driver/firmware as needed.
Signed-off-by: Rachit Kankane <quic_rkankane@quicinc.com>
Signed-off-by: Aleti Nageshwar Reddy <quic_anageshw@quicinc.com>
Fix the following compiler error:
qca-vendor.h:5892:54: error: result of ‘1 << 31’ requires 33 bits to represent, but ‘int’ only has 32 bits [-Werror=shift-overflow=]
5892 | QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40INTOL = 1 << 31,
This "1" needs to be marked unsigned for this case of MSB=1.
Signed-off-by: Chaoli Zhou <quic_zchaoli@quicinc.com>
hostapd based automatic channel selection doesn't update the hardware
mode after the channel is selected. This change specifically helps
channel 14 which can operate only in IEEE 802.11b mode.
Signed-off-by: Sunil Ravi <sunilravi@google.com>
bss->conf->bssid may be kept unset and will cause an empty BSSID field
in RNR. Fix this to use own_addr instead.
Signed-off-by: Shay Bar <shay.bar@celeno.com>
Signed-off-by: moran.daori <moran.daori@celeno.com>
The ACS info messages frequently appear for multiple channels. Without
the actual frequency in the messages, they are not very informative.
Add the frequency to them to improve this.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Don't select channels designated for exclusive indoor use when the
country string is set for outdoor operation (country3=0x4f, i.e., the
third character of the country string is 'O').
Signed-off-by: David Bauer <mail@david-bauer.net>
Add a new attribute QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_SP_START_OFFSET to
configure offset to shift start of the service period. This attribute
will be used when device supports flexible TWT. If provided, this
attribute will override QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_WAKE_TIME.
Signed-off-by: nakul kachhwaha <quic_nkachhwa@quicinc.com>
Parse link id info from channel switch events and indicate the info to
control interface using new per link channel switch events. If channel
switch happens on the link which used during association both legacy
and new per-link channel switch events will be reported.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add support to fetch and indicate per-link MLO signal poll information
via a new control interface command MLO_SIGNAL_POLL.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add bssid as parameter to nl80211_get_link_signal() instead of using
bssid from driver structure. This is useful for calling the function
per-MLO link.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add a utility function to fetch Multi-Link Device (MLD) address from a
Basic Multi-Link element.
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
Use AP MLD address as the peer's MAC address to set supplicant port as
authorized for MLO connection.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add support to fetch MLO connection info from the driver to the
wpa_supplicant instance of corresponding MLD STA interface. In addition,
return true for BSSs associated with MLO links from wpa_bss_in_use() to
avoid getting them cleared from scan results.
Co-authored-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Signed-off-by: Shivani Baranwal <quic_shivbara@quicinc.com>
Parse NL80211_ATTR_MLO_LINKS in NL80211_CMD_CONNECT event and cache the
MLO connection information. Set the legacy connection fields such as
assoc_freq and bssid to the values of the MLO link on which association
happened.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Define the following fields described in IEEE P802.11be/D2.1:
- Multi-Link element types as defined in Table 9-401c (Type subfield
encoding)
- Basic Multi-Link element presence bitmap as defined in Figure
9-1002g (Presence Bitmap subfield of the Basic Multi-Link element
format)
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
P2P connections in the 6 GHz band should be limited to preferred
scanning channels since AP/GO discovery cannot depend on 2.4/5 GHz
discovery.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Support updating the RRM IEs to the driver for Probe Response and
(Re)Association response frames in the AP mode when the SME is
implemented in the driver.
Signed-off-by: Chaoli Zhou <quic_zchaoli@quicinc.com>
Set TWT responder configurator in the driver parameters only when the AP
is configured with HE enabled. This was already done for the extended
capability bit generation in commit 8de0ff0fa1 ("HE: Add TWT responder
extended capabilities field"), but this parameter for the driver command
to start the AP in _ieee802_11_set_beacon() missed the condition.
Move the ieee80211ax check into the common helper function to cover both
cases. In addition, add a check for disable_11ax to cover the case where
HE is disabled for a specific BSS.
Fixes: ab8c55358e ("HE: Dynamically turn on TWT responder support")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Extend attributes of subcmd QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO
for quering per MCS TX and RX packets from the driver/firmware.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a new QCA vendor attribute to configure the periodic sounding for Tx
beamformer functionality.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Do not complain about unprotected Action frames for additional
categories that have been defined as not being Robust.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Verify that the MAC Address KDE includes enough data to contain a MAC
address as a part of the parsing function so that each caller would not
need to verify this separately. None of the existing users of this
parser actually needed the MAC address value, so there was not any use
for the length field before. The updated design is more robust for
future uses and gets rid of that unused length field as well.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
When an entry is added to the PTKSA cache, timer expiration is not set.
Check the list and set the timer expiration when the list is empty also.
When another entry is added to the list, it is placed before the relavant
entry in the order of expiry time of all entries present in the list.
Fixes: a4e3691616 ("WPA: Add PTKSA cache implementation")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
After the secure association and PTK derivation are completed, if the
device supports LTF keyseed, generate the LTF keyseed using KDK and set
the ranging context to the driver by using the command
QCA_NL80211_VENDOR_SUBCMD_SECURE_RANGING_CONTEXT.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
AP as a responder, on successful completion of PASN authentication
configures the required keys by using the command
QCA_NL80211_VENDOR_SUBCMD_SECURE_RANGING_CONTEXT to the driver.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This defines the QCA vendor interface functions to offload PASN
authentication from the driver.
The driver sends the QCA_NL80211_VENDOR_SUBCMD_PASN event requesting to
perform PASN authentication with a list of peers with which the driver
needs to do ranging. wpa_supplicant performs PASN handshake with all the
peer devices and sets the required keys using the command
QCA_NL80211_VENDOR_SUBCMD_SECURE_RANGING_CONTEXT to the driver. After
PASN handshake is completed with all requested peers, wpa_supplicant
sends consolidated status for all peers to the driver.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
To support secure ranging with a random MAC address, PASN handshake is
performed with a different source MAC address from the device's own
interface address. Hence, allow PASN Authentication frames with any
foreign MAC address to further process the Authentication frames.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add an option for an alternative processing of PTKSA life time expiry.
Register a callback in wpa_supplicant to handle the life time expiry of
the keys in PTKSA cache. Send PASN deauthentication when a PTKSA cache
entry expires.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This brings in the function declarations and data structures that are
required for handling PASN request from the driver, sending secure
ranging context and PASN response to the driver.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a function to derive the LTF keyseed from KDK. This function is
built only in case that CONFIG_PASN is enabled at build time.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
On successful PASN handshake or 4-way handshake with a peer, PTK is
derived using the local and peer MAC addresses as input. Store the own
MAC address that is used for key derivation in PTKSA cache to maintain
that state over potential MAC addresses changes.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Use separate capabilities for AP and STA modes for P802.11az security
parameters secure LTF support, secure RTT measurement exchange support,
and protection of range negotiation and measurement management frames
support.
P802.11az security parameters are considered to be supported for both
station and AP modes if the driver sets NL80211_EXT_FEATURE_SECURE_LTF,
NL80211_EXT_FEATURE_SECURE_RTT, and
NL80211_EXT_FEATURE_PROT_RANGE_NEGO_AND_MEASURE flags. The driver can
advertize capabilities specific to each mode using
QCA_WLAN_VENDOR_FEATURE_SECURE_LTF*,
QCA_WLAN_VENDOR_FEATURE_SECURE_RTT*, and
QCA_WLAN_VENDOR_FEATURE_PROT_RANGE_NEGO_AND_MEASURE* flags.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This fixes the build with OpenSSL 1.1.1:
../src/crypto/crypto_openssl.c: In function 'crypto_rsa_oaep_sha256_decrypt':
../src/crypto/crypto_openssl.c:4404:49: error: 'RSA_PKCS1_OAEP_PADDING' undeclared (first use in this function)
Signed-off-by: Andre Heider <a.heider@gmail.com>
Reorder PKEX initiation function to send out the PKEX Exchange Request
frame at the end after all possible error cases have been checked. This
prevents Enrollee from seeing a PKEX frame when the session is about to
fail.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add QCA_NL80211_VENDOR_SUBCMD_GET_SAR_CAPABILITY to get various SAR
capabilities supported by the WLAN firmware to userspace. These
capabilites are usually reported by the firmware during the initial
bootup handshake with the driver. Based on these capabilities, user
space can choose proper SAR indexes.
Signed-off-by: Mukul Sharma <quic_mukul@quicinc.com>
Add support to configure SAE, PSK, and PSK-SHA256 AKMs in connect
request when driver's SME in use. This is needed for implementing
WPA3-Personal transition mode correctly with any driver that handles
roaming internally.
Send additional AKMs configured in network block to driver based on
the maximum number of AKMs allowed by driver in connect request. Keep
first AKM in the list AKMs in the connect request as AKM selected by
wpa_supplicant to maintain backwards compatibility.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Use the recently added attribute to determine whether the kernel
supports a larger number of AKM suites in various commands.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
This brings in nl80211 definitions as of 2022-07-22. In addition, update
nl80211_command_to_string() to cover the new defined commands.
Signed-off-by: Jouni Malinen <j@w1.fi>
hostapd_dpp_add_controller() ended up trying to parse the IP address
without nul terminating it. This might work with some C libraries, but
not all. And anyway, this was already supposed to nul terminate the
string since a temporary copy is created of the constant string. Fix
this by adding the missed replacement of the space with nul.
Fixes: bfe3cfc382 ("DPP: Allow Relay connections to Controllers to be added and removed")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
u64 needs "long long unsigned int" on 32-bit, so print this using a
typecase value so that both 32 and 64-bit builds work fine.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
EVP_PKEY_derive() might report a larger maximum size of the output than
HPKE_MAX_SHARED_SECRET_LEN under some conditions. That should be allowed
as long as the real final length is within the maximum limit.
Furthermore, since we are using a fixed length buffer for this, there is
no need to call EVP_PKEY_derive() twice to first learn the maximum
length. Use a bit longer buffer and allow OpenSSL to take care of the
update to the final length internally with than single call.
This showed up using the following test case sequence:
dbus_pkcs11 dpp_private_peer_introduction
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This can be helpful for upper layers to be able to determine whether the
configuration was rejected.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Enhance QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH event for the
driver to indicate the information of the associated links of MLO
roaming.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
The initial timeout of 10 seconds for the first scan before knowing
whether the driver reports scan completion events may not be sufficient
in cases where the driver ends up scanning a large number of channels.
In particular, this could be hit with 6 GHz support. Increase this
timeout when the driver indicates support for 6 GHz channels.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The <openssl/buf.h> include is relevant in both OpenSSL and BoringSSL
because the file uses BUF_MEM (include what you use). OpenSSL just
happened to include it via another file. OpenSSL also spells it
<openssl/buffer.h>, not matching the type, so use the compatible
spelling.
Additionally all the CHECKED_CAST and manual STACK_OF(T) definitions
call into BoringSSL internals. The correct, public APIs are simply to
just use the same code as OpenSSL and call the DEFINE_STACK_OF macros.
Signed-off-by: David Benjamin <davidben@google.com>
Commit 74818ca63f ("Process
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH after NL80211_CMD_ROAM")
added workaround to hold the pending
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH event data for up to 100 ms
in case NL80211_CMD_ROAM is not received first. The 100 ms wait period
was sufficient for most of the cases but it's observed that some times
kernel is taking more than 100 ms to process and send NL80211_CMD_ROAM
to userspace.
If NL80211_CMD_ROAM takes more than 100 ms
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH event data getting ignored
though wpa_supplicant has it. To avoid this remove timeout for
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH event data since driver
always indicates NL80211_CMD_ROAM along with
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH.
In addition, clear the pending event data when marking the interface
disconnected since the roaming information is supposed to be used only
when reassociating without a disconnection.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Previously when chains of BT and WLAN 2.4 GHz are separated,
hybrid mode will be used for BTC. Now adding fixed FDD mode
to fulfill different BTC scenarios.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The Enrollee may report its supported curves in the bootstrapping URI.
If it does that, the Configurator may stop generating the Config Object
that would depend on the Enrollee using a curve that it did not indicate
as being supported. Check for this case while proessing the Config
Request and stop Configurator from building a configuration that is
known not to work.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Select the PMK length based on the used group (prime length) when using
the new AKM suites for SAE.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
SAE authentication needs to known which AKM suite is being used to be
able to determine the correct PMK length for the new AKM suite selectors
that use variable length keys.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The new SAE AKM suites are defined to use H2E, so ignore the sae_pwe
value when these AKM suites are used similarly to the way H2E gets
enabled when SAE Password Identifiers are used.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Update the AKM suite specific mapping of various EAPOL-Key key lengths
and algorithms to include the new SAE AKM suites with variable length
keys.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Define new WPA_KEY_MGMT_* values for the new SAE AKM suite selectors
with variable length keys. This includes updates to various mapping and
checking of the SAE key_mgmt values.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Use the existing helper function instead of maintaining multiple copies
of lists of SAE key management suites.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The new DPP-RELAY-NEEDS-CONTROLLER control interface event can be used
to trigger mDNS discovery of a Controller to see if such a connection
can be established automatically at the time an Enrollee is trying to
initiate an operation.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The new control interface commands "DPP_RELAY_ADD_CONTROLLER <IP addr>
<PK hash>" and "DPP_RELAY_REMOVE_CONTROLLER <IP addr>" can now be used
to dynamically add and remove connections to Controllers for the cases
where the connection is initialized through a DPP Public Action frame
(i.e., Controller as the Responder).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Instead of requiring explicit configuration through
dpp_configurator_connectivity=1, advertise Configurator connectivity
automatically if a Relay is configured with a Controller that can
operate as a Responder.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Accept an incoming TCP connection from a Controller in a Relay that is
configured with dpp_relay_port even if that Controller is not configured
with a dpp_controller parameter. This allows more dynamic Controller
initiated operations, e.g., when using mDNS to discover a Relay.
This type of a dynamic Controller entry will not be used for exchanges
that are initiated by an Enrollee (i.e., based on a DPP Public Action
frame received by the Relay).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Verify that the peer does not change its bootstrapping key between the
PKEX exchange and the authentication exchange.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
When PKEX was started through the push button mechanism, the own
bootstrapping key was not bound correctly to the Authentication phase
information and that ended up in incorrectly generating a new
bootstrapping key for the Authentication exchange. Fix this by added the
needed own=<id> parameter into the cached parameters when using push
button.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The peer=<id> information about the specific boostrapping key provided
through PKEX was added for Public Action frame cases, but the TCP
variant did not do same. Add the same information there to maintain
knowledge of the specific peer bootstrapping key from PKEX to
Authentication exchange.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Extend DPP push button support in wpa_supplicant to allow the role of
the Configurator to be used. This provides similar functionality to the
way the DPP_PUSH_BUTTON command in hostapd worked when providing the
configuration parameters with that command (instead of building the
config object based on current AP configuration).
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
It is possible for a Controller to receive a copy of its own PKEX
Exchange Request in the case where the Controller is initiating a PKEX
exchange through a Relay. The Configurator role in the device would have
a matching PKEX code in that case and the device might reply as a PKEX
responder which would result in going through the exchange with the
Controller device itself. That is clearly not desired, so recognize this
special case by checking whether the Encrypted Key attribute value
matches a pending locally generated one when processing a received PKEX
Exchange Request.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This gets the Controller (DPP-over-TCP) sequence closer to the one used
with Public Action frames and makes it easier for upper layer components
to share the same design for tracking operation status.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Relay will need to allow the PKEX Exchange Response message to be
handled similarly to the Authentication Response message to allow this
sequence to be completed successfully.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
We are not supposed to reuse these without being explicitly requested to
perform PKEX again. There is not a strong use case for being able to
provision an Enrollee multiple times with PKEX, so this should have no
issues on the Enrollee. For a Configurator, there might be some use
cases that would benefit from being able to use the same code with
multiple Enrollee devices, e.g., for guess access with a laptop and a
smart phone. That case will now require a new DPP_PKEX_ADD command on
the Configurator after each completion of the provisioning exchange.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a privacy protecting variant of the peer introduction protocol to
allow the station device to hide its Connector from 3rd parties. The new
wpa_supplicant network profile parameter dpp_connector_privacy=1 can be
used to select this alternative mechanism to the peer introduction
protocol added in the initial release of DPP.
It should be noted that the new variant does not work with older DPP APs
(i.e., requires support for release 3). As such, this new variant is
disabled by default.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add support for HPKE base mode with single-shot API (see RFC 9180) using
OpenSSL. This is needed for DPP private introduction protocol.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This allows the DPP Configuration Object from a Configurator to be
extended with 3rd party information. This information can be provided as
a part of the existing configuration specification mechanisms with the
new extra_name=<string> and extra_value=<hexdump encoded JSON>.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This allows the DPP Configuration Request Object from an Enrollee to be
extended with 3rd party information. The new dpp_extra_conf_req_name and
dpp_extra_conf_req_value configuration parameters specify the name of
the added JSON node and its contents. For example:
dpp_extra_conf_req_name=org.example
dpp_extra_conf_req_value={"a":1,"b":"test"}
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a new vendor subcommand QCA_NL80211_VENDOR_SUBCMD_SCS_RULE_CONFIG
for configuration event of Stream Classification Service (SCS) rule.
Also define the attributes present in this subcommand.
Signed-off-by: Harsh Kumar Bijlani <quic_hbijlani@quicinc.com>
Add a new vendor attribute QCA_WLAN_VENDOR_ATTR_CONFIG_DBAM to
configure Dedicated Bluetooth Antenna Mode (DBAM). It is used to
switch between dedicated antenna mode for BT and COEX shared
antenna mode for WLAN and BT.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This extends Relay functionality to allow a Controller to intitiate a
new DPP exchange in addition to the previously supported case where the
exchange was initiated through a DPP Public Action frame.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
While the most likely production use case for DPP push button is to
provision the AP's current configuration, there might be some use cases
for providing different configuration. Add possibility for doing this by
extending the DPP_PUSH_BUTTON command to accept an optional set of
parameters similarly to the other DPP commands for the Configurator.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Allow the Responder/Initiator hash values to be corrupted in Push Button
Presence Announcement messages for testing purposes.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add support to use a push button -based bootstrap mechanism with DPP.
The new DPP_PUSH_BUTTON control interface command enables this mode on
the AP/hostapd and station/wpa_supplicant. This goes through the
following sequence of events: a suitable peer in active push button mode
is discovered with session overlap detection, PKEX is executed with
bootstrap key hash validation, DPP authentication and configuration
exchanges are performed.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add feature capability indication for P802.11az security for the drivers
to advertise capabilities such as secure LTF support, secure RTT
measurement exchange support, and protection of range negotiation and
measurement management frames for station and AP interfaces
independently. This allows a more fine-tuned capability indication as an
alternative to the upstream nl80211 mechanism that is not specific to
the operating mode.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add vendor command QCA_NL80211_VENDOR_SUBCMD_COAP_OFFLOAD to
enable/disable offload processing in firmware for CoAP messages
(RFC7252: The Constrained Application Protocol) or fetch the
CoAP messages cached during offload processing.
Signed-off-by: Yu Wang <quic_yyuwang@quicinc.com>
Add the following two vendor attributes to send TIM beacon
statistics to userspace which can be used for power saving:
QCA_WLAN_VENDOR_ATTR_LL_STATS_TIM_BEACON
QCA_WLAN_VENDOR_ATTR_LL_STATS_TIM_BEACON_ERR
Signed-off-by: Jingxiang Ge <quic_jge@quicinc.com>
Define QCA vendor interface for PASN offload to userspace from the driver.
The driver can send this command as an event to a userspace component to
perform PASN authentication with a list of peers with which the driver
needs to do ranging. The userspace component, if capable of performing
PASN handshake, can perform PASN handshake with all the peer devices and
set the relevant keys by sending the
QCA_NL80211_VENDOR_SUBCMD_SECURE_RANGING_CONTEXT command for each peer
to the driver.
Once PASN handshake is completed with all requested peers, the userspace
component sends consolidated status for all the peers to the driver. The
consolidated report is required for the driver to understand that the
PASN handshake process is complete and whether it succeeded/failed for
each of the peers it was requested for. The secure ranging context is
configured only for the peers with which the PASN handshake succeeded.
When the driver requests PASN keys, the userspace component can set the
keys from its cache if those keys have not already expired and were
derived with the same source MAC address that is requested by the driver
instead of doing the full PASN handshake again.
If the driver detects that current keys of a peer are not valid anymore,
it sends a notification to userspace using the
QCA_NL80211_VENDOR_SUBCMD_PASN command and setting the action to
QCA_WLAN_VENDOR_PASN_ACTION_DELETE_SECURE_RANGING_CONTEXT. The userspace
component should delete the corresponding keys from its cache.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Add a new QCA vendor attribute
QCA_WLAN_VENDOR_ATTR_CONCURRENT_POLICY_AP_CONFIG to
QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_POLICY sub command to set the
concurrency policy for AP interface.
QCA_WLAN_VENDOR_ATTR_CONCURRENT_POLICY_AP_CONFIG uses the values
defined in enum qca_wlan_concurrent_ap_policy_config to specify
concurrency policy.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
Rename QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_MULTI_STA_POLICY to
QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_POLICY to allow extension for other
interface type(s). A subsequent commit will extend the renamed
definitions in a manner that is inconsistent with the current naming.
This is a precursor for AP/P2P concurrency policy configuration support
via updated vendor command QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_POLICY.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
Move most of CHANWIDTH_* definitions from ieee80211_defs.h to defs.h as
the definitions are getting used mostly for internal purpose only. Also
change prefix of the definitions to CONF_OPER_CHWIDTH_* and update in
all the files accordingly.
Leave the couple of VHT-specific exceptions to use the old defines (the
reason why they were originally added as VHT values), to avoid use of
clearly marked configuration values in information elements. In
addition, use the defines instead of magic values where appropriate.
Signed-off-by: Aleti Nageshwar Reddy <quic_anageshw@quicinc.com>
Add QCA vendor event to indicate user space that the driver recovery is
completed after the internal failure reported with
QCA_NL80211_VENDOR_SUBCMD_HANG.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add a new QCA vendor attribute
QCA_WLAN_VENDOR_ATTR_CONFIG_AUDIO_DATA_PATH to
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION to configure audio data
path.
Possible audio data paths are defined in enum qca_wlan_audio_data_path.
Signed-off-by: Purushottam Kushwaha <quic_pkushwah@quicinc.com>
Vendor command to get the WLAN radio combinations matrix supported by
the device which provides the device simultaneous radio configurations
such as standalone, dual band simultaneous, and single band
simultaneous.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The initial OCV implementation validating this field in the OCI element
for both the 80+80 MHz and 160 MHz cases. However, IEEE Std 802.11-2020,
12.2.9 ("Requirements for Operating Channel Validation") limitis that
verification step for the 80+80 MHz case: "Verifying that, if operating
an 80+80 MHz operating class, the frequency segment 1 channel number ...
is equal to the Frequency Segment 1 Channel Number field of the OCI."
Remove this check for the 160 MHz case since there has been incorrect
interpretation on how the Frequency Segment 1 Channel Number field of
the OCI element is set in this case (using VHT rules for CCFS2). The
modified validation step is meets the real need here, is compliant with
the standard, and avoids potential interoperability issues when using
contiguous 160 MHz channels.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Previously, the driver could optionally (using QCA vendor command)
provide a preferred channel list to wpa_supplicant for channel selection
during the GO negotiation. Channel selection process can be more
efficient with the information of weights and flags of the preferred
channel list that can be provided by the driver. Use a weighted
preferred channel list provided by the driver for channel selection
during GO negotiation if such a list is available.
Signed-off-by: Sreeramya Soratkal <quic_ssramya@quicinc.com>
Add QCA_ATTR_ROAM_CONTROL_RX_LINKSPEED_THRESHOLD value as the RX link
speed threshold to disable roaming. If the current link speed is above
the threshold, there is no need to roam.
Signed-off-by: Jianmin Zhu <quic_jianminz@quicinc.com>
Add a new QCA vendor attribute
QCA_WLAN_VENDOR_ATTR_ACS_LAST_SCAN_AGEOUT_TIME to
QCA_NL80211_VENDOR_SUBCMD_DO_ACS and opportunistically optimize time
taken for ACS scan. Avoid scanning the channels which were scanned
within last QCA_WLAN_VENDOR_ATTR_ACS_LAST_SCAN_AGEOUT_TIME milliseconds
and use scan results from the scan results cache for ACS scoring. For
other channels, perform ACS scan and use the received scan results.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
When 6 GHz channels are included in channel list of P2P Action frames
but some peer devices don't support the 6 GHz feature and cannot parse
P2P IE data correctly, P2P handshake will fail.
Remove 6 GHz channels from the P2P Action frames if the peer doesn't
support 6 GHz feature to avoid such failures.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
A few of the comments in the QCA vendor commands have a space
character before a tab. That is pointless, and some code style
checkers may complain about it, so remove the spaces.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Skip the x_snoop_deinit() operations if hostapd did not actually
configure the parameters in the first place. While clearing these
specific parameters is unlikely to change how they were set outside the
scope of hostapd, it is better to leave them as-is to avoid surprises if
hostapd was not configured to use ProxyARP.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The initialization values used for the FIPS 186-2 PRF are identical to
the ones used in SHA1Init(), so use that internal function instead of
maintaining a duplicate set of values here. fips186_2_prf() was already
using an internal SHA1Transform() function so using another internal
function does not make this any worse.
Signed-off-by: Jouni Malinen <j@w1.fi>
OpenSSL 3.0 has deprecated the low-level SHA1 functions and does not
include an upper layer interface that could be used to use the
SHA1_Transform() function. Use the internal SHA-1 implementation instead
as a workaround.
While this type of duplicate implementation of SHA-1 is not really
ideal, this PRF is needed only for EAP-SIM/AKA and there does not seem
to be sufficient justification to try to get this working more cleanly
with OpenSSL 3.0.
Signed-off-by: Jouni Malinen <j@w1.fi>
The EVP_MAC context data needs to be freed on error paths.
Fixes: e31500adea ("OpenSSL: Implement HMAC using the EVP_MAC API")
Signed-off-by: Jouni Malinen <j@w1.fi>
The conversion to the new OpenSSL 3.0 API had forgotten to free the
context structure.
Fixes: bcd299b326 ("OpenSSL: Convert DH/DSA parameter loading to new API")
Signed-off-by: Jouni Malinen <j@w1.fi>
Extend IMSI privacy functionality to allow an attribute (in name=value
format) to be added using the new imsi_privacy_attr parameter.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Use imsi_privacy_cert as the name of the configuration parameter for the
X.509v3 certificate that contains the RSA public key needed for IMSI
privacy. The only allowed format for this information is a PEM-encoded
X.509 certificate, so the previous name was somewhat confusing.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
This is an allocated resource so it needs to be free on the error path.
Fixes: 42871a5d25 ("EAP-SIM/AKA peer: IMSI privacy")
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Commit 9afb68b039 ("OpenSSL: Allow systemwide secpolicy overrides for
TLS version") with commit 58bbcfa31b ("OpenSSL: Update security level
drop for TLS 1.0/1.1 with OpenSSL 3.0") allow this workaround to be
enabled with an explicit network configuration parameter. However, the
default settings are still allowing TLS 1.0 and 1.1 to be negotiated
just to see them fail immediately when using OpenSSL 3.0. This is not
exactly helpful especially when the OpenSSL error message for this
particular case is "internal error" which does not really say anything
about the reason for the error.
It is is a bit inconvenient to update the security policy for this
particular issue based on the negotiated TLS version since that happens
in the middle of processing for the first message from the server.
However, this can be done by using the debug callback for printing out
the received TLS messages during processing.
Drop the OpenSSL security level to 0 if that is the only option to
continue the TLS negotiation, i.e., when TLS 1.0/1.1 are still allowed
in wpa_supplicant default configuration and OpenSSL 3.0 with the
constraint on MD5-SHA1 use.
Signed-off-by: Jouni Malinen <j@w1.fi>
tcp_addr=from-uri can now be used as a special case for initiating
DPP-over-TCP to the destination indicated in the peer bootstrapping URI.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Parse the host information, if present, in bootstrapping URI and allow
such information to be added when generating the URI.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Only use the bandwidth bits that are applicable for the current
operating band. This avoids use of reserved bits when determining the
length of the Support EHT-MCS And NSS Set field length.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
IEEE Std 802.11-2020 is ambiguous on how the Secure bit is set in
EAPOL-Key msg 1/4 and 2/4 in the case where 4-way handshake is use to
rekey the PTK. 12.7.2 describes this with "set to 1 once the initial key
exchange is complete" while 12.7.6 shows EAPOL-Key msg 1/4 and 2/4 using
Secure=0 without any consideration on whether the handshake is for
rekeying.
TGme seems to be moving towards clarifying this to use Secure=1 based on
there being a shared PTKSA between the Authenticator and the Supplicant.
In other words, this would use Secure=1 in EAPOL-Key msg 1/4 and 2/4 in
the case of rekeying. Change implementation to match that. This bit was
already practically ignored on the reception side, so this should not
have impact on actual functionality beyond this one bit changing its
value in the frame.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Check the full MBIE length against the buffer length explicitly before
the debug print. This is for locally generated data, so the bounds
checking is not critical here, but it is better to use proper checking
anyway to avoid static analyzer complaints.
Signed-off-by: Jouni Malinen <j@w1.fi>
Avoid the somewhat confusing mechanism of determining the bitfield index
from the assigned IP address to make this easier for static analyzers.
Signed-off-by: Jouni Malinen <j@w1.fi>
Limit the GAS comeback delay to 60000 TUs, i.e., about 60 seconds. This
is mostly to silence static analyzers that complain about unbounded
value from external sources even though this is clearly bounded by being
a 16-bit value.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use local variables and common checking of the selector (or vendor
specific IE header) to make the bounds checking easier to understand.
Signed-off-by: Jouni Malinen <j@w1.fi>
BIT(r) is not sufficient here since it does not cover 64 bit values.
Write this out with 1ULL to be large enough for the shift operation.
Signed-off-by: Jouni Malinen <j@w1.fi>
The EHT changes made this checking inconsistent. If he_cap can be NULL
in case of EHT being enabled, better make sure it does not get
dereferenced without an explicit check.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is testing code, but it's better to check the return value
explicitly even if this were not really able to fail in practice.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like fst_wpa_obj::get_hw_modes would have been left
uninitialized in hostapd. It is not obviously clear why this would not
have caused issues earlier, but in any case, better make this set
properly to allow unexpected behavior should that function pointer ever
be used.
Signed-off-by: Jouni Malinen <j@w1.fi>
Nul terminate the struct p2p_go_neg_results::passphrase explicitly to
keep static analyzers happier. This was already nul terminated in
practice due to the full array being cleared to zero on initialization,
but that was apparently not clear enough for some analyzers.
Signed-off-by: Jouni Malinen <j@w1.fi>
Set NL80211_SCAN_FLAG_COLOCATED_6GHZ in the scan parameters to enable
scanning for co-located APs discovered based on neighbor reports from
the 2.4/5 GHz bands when not scanning passively. Do so only when
collocated scanning is not disabled by higher layer logic.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Without this, hostapd generates Probe Response frames with the null
destination address when hostapd enables unsolicited Probe Response
frame transmission. Fix this to use the broadcast address instead.
Fixes: 024b4b2a29 ("AP: Unsolicited broadcast Probe Response configuration")
Signed-off-by: MeiChia Chiu <meichia.chiu@mediatek.com>
RSN design is supposed to encrypt all Data frames, including EAPOL
frames, once the TK has been configured. However, there are deployed
implementations that do not really follow this design and there are
various examples from the older uses of EAPOL frame where those frames
were not encrypted. As such, strict filtering of unencrypted EAPOL
frames might results in undesired interoperation issues.
However, some of the most important cases of missing EAPOL frame
encryption should be possible to handle without causing too significant
issues. These are for cases where an attacker could potentially cause an
existing association to be dropped when PMF is used. EAPOL-Start and
EAPOL-Logoff are potential candidate for such attacks since those frames
could be used to terminate an authentication or initiate a new EAP
authentication. Such an attack could result in the station ending up
disconnecting or at minimum, getting into somewhat mismatching state
with the AP.
Drop EAPOL-Start/Logoff/EAP frames on the AP/Authenticator when it is
known that it was not encrypted but should have been and when PMF is
enabled. While it would be correct to drop this even without PMF, that
does not provide any significant benefit since it is trivial to force
disconnection in no-PMF cases. It should also be noted that not all
drivers provide information about the encryption status of the EAPOL
frames and this change has no impact with drivers that do not indicate
whether the frame was encrypted.
Signed-off-by: Jouni Malinen <j@w1.fi>
RSN design is supposed to encrypt all Data frames, including EAPOL
frames, once the TK has been configured. However, there are deployed
implementations that do not really follow this design and there are
various examples from the older uses of EAPOL frame where those frames
were not encrypted. As such, strict filtering of unencrypted EAPOL
frames might results in undesired interoperation issues.
However, some of the most important cases of missing EAPOL frame
encryption should be possible to handle without causing too significant
issues. These are for cases where an attacker could potentially cause an
existing association to be dropped when PMF is used. EAP-Request is one
potential candidate for such attacks since that frame could be used to
initiate a new EAP authentication and the AP/Authenticator might not
allow that to complete or a large number of EAP-Request frames could be
injected to exceed the maximum number of EAP frames. Such an attack
could result in the station ending up disconnecting or at minimum,
getting into somewhat mismatching state with the AP.
Drop EAPOL-EAP frames when it is known that it was not encrypted but
should have been and when PMF is enabled. While it would be correct to
drop this even without PMF, that does not provide any significant
benefit since it is trivial to force disconnection in no-PMF cases. It
should also be noted that not all drivers provide information about the
encryption status of the EAPOL frames and this change has no impact with
drivers that do not indicate whether the frame was encrypted.
Signed-off-by: Jouni Malinen <j@w1.fi>
RSN design is supposed to encrypt all Data frames, including EAPOL
frames, once the TK has been configured. However, there are deployed
implementations that do not really follow this design and there are
various examples from the older uses of EAPOL frame where those frames
were not encrypted. As such, strict filtering of unencrypted EAPOL
frames might results in undesired interoperation issues.
However, some of the most important cases of missing EAPOL frame
encryption should be possible to handle without causing too significant
issues. These are for cases where an attacker could potentially cause an
existing association to be dropped when PMF is used. EAPOL-Key msg 1/4
is one potential candidate for such attacks since that frame could be
used to initiate a 4-way handshake that the real AP might never complete
and the station might end up disconnecting because of that or at
minimum, getting into somewhat mismatching state with the AP.
Drop EAPOL-Key msg 1/4 when it is known that it was not encrypted but
should have been and when PMF is enabled. While it would be correct to
drop this even without PMF, that does not provide any significant
benefit since it is trivial to force disconnection in no-PMF cases. It
should also be noted that not all drivers provide information about the
encryption status of the EAPOL frames and this change has no impact with
drivers that do not indicate whether the frame was encrypted.
Signed-off-by: Jouni Malinen <j@w1.fi>
EAPOL-Key Request frame with Error=1 is not really a request for a new
key, so allow that frame to be sent even if PTK0 rekey is not allowed
since the supplicant is required to report Michael MIC errors to the
authenticator.
Signed-off-by: Jouni Malinen <j@w1.fi>
This information was already available from the nl80211 control port RX
path, but it was not provided to upper layers within wpa_supplicant and
hostapd. It can be helpful, so parse the information from the driver
event.
Signed-off-by: Jouni Malinen <j@w1.fi>
sm->pairwise_set needs to be set whenever the TK has been configured to
the driver to request following EAPOL frames to be encrypted (or more
specifically, not to request them to not be encrypted). The FILS case
missed this setting and that could result in rekeying or
reauthentication in an associated started with FILS not working
correctly.
Fixes: da24c5aa1c ("FILS: Set TK after association (AP)")
Signed-off-by: Jouni Malinen <j@w1.fi>
The wpa_supplicant check for whether a TK is configured into the driver
was broken during the time this information is needed for rekeying or
reauthenticating with another 4-way handshake. sm->ptk.installed is not
set at the point the EAPOL-Key msg 4/4 is sent and while that means the
initial 4-way handshake needs to prevent encryption, the consecutive
4-way handshake must not be doing that since the old key (TK) is still
in the driver. Fix this so that the EAPOL-Key msg 4/4 during rekeying
does not get transmitted without encryption.
Fixes: a79ed06871 ("Add no_encrypt flag for control port TX")
Signed-off-by: Jouni Malinen <j@w1.fi>
Currently a corrupted handshake message 1/4 causes the client to
disconnect from the network. This can lead to a denial-of-service
vulnerability allowing an adversary to forcibly disconnect a client from
protected networks even when Wi-Fi Management Frame Protection (MFP) is
enforced if the driver allows unencrypted EAPOL-Key frames to be
received after key configuration..
Fix this by discarding the corrupted handshake message 1/4.
This issue was discovered by Domien Schepers (Northeastern University)
and Mathy Vanhoef (imec-DistriNet, KU Leuven).
Signed-off-by: Domien Schepers <schepers.d@northeastern.edu>
wpa_validate_wpa_ie() might update sm->* values, so it should not be
allowed for an existing STA entry if that STA has negotiated MFP to be
used for the association. Fix this by first checking whether an SA Query
procedure needs to be initiated. In particular, this prevents a
potential bypass of the disconnection protection.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
The driver can consider EHT specific parameters such as the puncture
pattern for ACS when this flag attribute is indicated by userspace.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Add a check to avoid sending VHT channel definition when EHT is enabled
in the 2.4 GHz band since the 2.4 GHz band isn't supposed to use VHT
operations. Also add EHT enabled info into debug prints.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Do not consider optional octets maximum lengths when validating EHT
fixed fields length. Furthermore, do not use the first two octets of the
PPE Thresholds field without explicitly confirming that these octets
were included in the element and fix PPE Thresholds field length
calculation.
Fixes: a6d1b4c46c ("EHT: Process (Re)Association Request frame capabilities")
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
