Send MESH-SAE-AUTH-BLOCKED event if SAE authentication is blocked. The
BLOCK state will finish when a new peer notification event is sent for
the same MAC address.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
SAE authentication fails likely with wrong password. This commit adds a
notification of the failure to the upper application (UI) so that the
application can notify suspection of a wrong password to the user. The
control interface monitor even for this is "MESH-SAE-AUTH-FAILURE
addr=<peer>".
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This modifies struct wpa_ptk to allow the length of KCK and KEK to be
stored. This is needed to allow longer keys to be used, e.g., with
Suite B 192-bit level.
Signed-off-by: Jouni Malinen <j@w1.fi>
The ANQP verification/parsing is done only after the GAS_DONE indication
is sent over the control interface. This means that in case the ANQP
parsing fails there is no indication to the upper layers. Add an
ANQP-QUERY-DONE event that reports the status of the ANQP parsing.
Signed-off-by: ASHUTOSH NARAYAN <ashutoshx.narayan@intel.com>
A new "CTRL-EVENT-EAP-PEER-ALT depth=<i> <alt name>" event is now used
to provide information about server certificate chain alternative
subject names for upper layers, e.g., to make it easier to configure
constraints on the server certificate. For example:
CTRL-EVENT-EAP-PEER-ALT depth=0 DNS:server.example.com
Currently, this includes DNS, EMAIL, and URI components from the
certificates. Similar information is priovided to D-Bus Certification
signal in the new altsubject argument which is a string array of these
items.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new VENDOR_ELEM value 13 can now be used to add a vendor element
into all (Re)Association Request frames, not just for P2P use cases like
the previous item was for.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows vendor specific information element to be used to advertise
support for VHT on 2.4 GHz band. In practice, this is used to enable use
of 256 QAM rates (VHT-MCS 8 and 9) on 2.4 GHz band.
This functionality is disabled by default, but can be enabled with
vendor_vht=1 parameter in hostapd.conf if the driver advertises support
for VHT on either 2.4 or 5 GHz bands.
Signed-off-by: Yanbo Li <yanbol@qti.qualcomm.com>
There should not be a mesh-specific mechanism for setting up channel
parameters since that will just result in duplicated code. IBSS, mesh,
and AP mode can use the same data structures and parameters for setting
up such parameters.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add the t0 retransmission timer as specified by IEEE Std 802.11-2012,
11.3.8.4. This makes SAE much more likely to succeed in the case of lost
frames.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
There is no need to keep temporary keys in memory beyond the end of the
association, so explicitly clear any SAE buffers that can contain keys
as soon as such keys are not needed.
Signed-off-by: Jouni Malinen <j@w1.fi>
struct wpa_driver_associate_params moved to using struct
hostapd_freq_params instead of just frequency. Need to update wpa_priv
to do same.
Signed-off-by: Jouni Malinen <j@w1.fi>
This commit introduces a QCA vendor command that allows interrogation of
the vendor-specific features supported by the device/driver. Currently
the only defined feature is the ability to offload key management.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This converts os_snprintf() result validation cases to use
os_snprintf_error() for cases that were note covered by spatch and
semantic patches.
Signed-off-by: Jouni Malinen <j@w1.fi>
Using QCA vendor command, allow ACS function to be offloaded to the
driver. Once channels are selected, hostapd is notified to perform OBSS
operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit inserts Finite Cyclic Group to Anti-Clogging Token request
frame because IEEE Std 802.11-2012, Table 8-29 says "Finite Cyclic Group
is present if Status is zero or 76".
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
The mesh anti-clogging functionality is implemented partially. This
patch fixes to parse anti-clogging request frame and use anti-clogging
token.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Some static analyzers had problems understanding "left < count * len"
(CID 62855, CID 62856), so convert this to equivalent "count > left /
len" (len here is fixed to 4, so this can be done efficiently).
Signed-off-by: Jouni Malinen <j@w1.fi>
Static analyzers may not have understood the bounds checking on
data->num_pmkid. Use a local, temporary variable and validate that that
value is within length limits before assining this to data->num_pmkid to
make this clearer. (CID 62857, CID 68126)
Signed-off-by: Jouni Malinen <j@w1.fi>
Send link measurement response when a request is received. Advertise
only RCPI, computing it from the RSSI of the request. The TX power field
is left to be filled by the driver. All other fields are not published.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add NEIGHBOR_REP_REQUEST command to the wpa_supplicant ctrl_iface.
This command triggers the sending of a Neighbor Report Request to the
associated AP.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Add the ability to send a Neighbor Report Request (part of
RRM). Requester is then notified once the report arrives.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
In case the AP we are associating with advertises support for RRM,
advertise our own RRM support in the (Re)Association Request frame. This
is done by adding an RRM Capabilities IE. The underlying driver is
expected to further add a Power Capabilities IE to the request, and set
the Radio Measurement flag in the Capability Info field. At this point
the RRM Capabilities IE advertises no measurement support.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
ieee80211_chan_to_freq() is a generic function that replaces and extends
the previous P2P-specific p2p_channel_to_freq(). The new function
supports both the global operating class table as well as the additional
US, EU, JP, and CN operating class tables.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible that a station device might miss an ACK for an
authentication, association, or action frame, and thus retransmit the
same frame although the frame is already being processed in the stack.
While the duplicated frame should really be dropped in the kernel or
firmware code where duplicate detection is implemented for data frames,
it is possible that pre-association cases are not fully addressed (which
is the case at least with mac80211 today) and the frame may be delivered
to upper layer stack.
In such a case, the local AP will process the retransmitted frame although
it has already handled the request, which might cause the station to get
confused and as a result disconnect from the AP, blacklist it, etc.
To avoid such a case, save the sequence control of the last processed
management frame and in case of retransmissions drop them.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add the TSPEC to the driver on successful TSPEC ADDTS response. Delete
the TSPEC when receiving DELTS action.
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Initialize WMM AC data structures upon successful association
with an AP that publishes WMM support, and deinitialize the data
structure when the association is no longer valid.
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Android 4.4 uses "BSS" command instead of "SCAN_RESULT" command.
So this patch add the mesh scan result for BSS command.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Parse MESH_GROUP_ADD/REMOVE commands on ctrl interface and call
wpa_supplicant routines. These commands are used to start or
join and leave a mesh network.
The mesh id is given in the configuration file, therefore there is
no need to scan before joining a mesh network. We reuse the
connect_without_scan construct used by P2P for that same purpose.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Add a new option "mesh_ht_mode" that specifies the HT mode for the
mesh, with this option on, mesh beacons, actions frames, and probe
responses with include the appropriate HT information elements.
[original implementation by Chun-Yeow Yeoh <yeohchunyeow@gmail.com>]
[some fixes by Masashi Honma <masashi.honma@gmail.com>]
Signed-off-by: Ashok Nagarajan <ashok.dragon@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
This adds support for AKM 00-0F-AC:11 to specify the integrity and
key-wrap algorithms for EAPOL-Key frames using the new design where
descriptor version is set to 0 and algorithms are determined based on
AKM.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new AKM uses a different mechanism of deriving the PMKID based on
KCK instead of PMK. hostapd was already doing this after the KCK had
been derived, but wpa_supplicant functionality needs to be moved from
processing of EAPOL-Key frame 1/4 to 3/4 to have the KCK available.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds definitions for the 128-bit level Suite B AKM 00-0F-AC:11. The
functionality itself is not yet complete, i.e., this commit only
includes parts to negotiate the new AKM.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is needed since the SCAN command with radio work returns before the
actual driver operation to trigger a scan has been executed and as such,
cannot return result of that operation.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
These can be convenient for upper layer programs to determine if the
hostapd interface gets disabled/re-enabled, e.g., due to rfkill
block/unblock.
Signed-off-by: Jouni Malinen <j@w1.fi>
The mesh peering manager establishes and maintains links among
mesh peers, tracking each peer link via a finite state machine.
This implementation supports open mesh peerings.
[assorted fixes from Yu Niiro <yu.niiro@gmail.com>]
[more fixes from Masashi Honma <masashi.honma@gmail.com>]
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Ashok Nagarajan <ashok.dragon@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-hostap: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
This commit introduces a QCA vendor command and event to provide an
option to use extended versions of the nl80211 connect/roam operations
in a way that allows drivers to offload key management operations to the
driver/firmware.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The definition of wpa_ctrl_get_remote_ifname is conditional on
CONFIG_CTRL_IFACE_UDP. This change makes the header declaration of
this function also conditional on the same define.
Signed-off-by: Toby Gray <toby.gray@realvnc.com>
Commit 4fdc8def88 changed the wpa_ctrl
socket to be be non-blocking, so the comment about wpa_ctrl_recv()
blocking is not valid anymore.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows updating roaming policy for drivers that select the BSS
internally so that wpa_supplicant (based on bssid parameter
configuration) and the driver remain in sync.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds hostapd support for the new WLAN-Pairwise-Cipher,
WLAN-Group-Cipher, WLAN-AKM-Suite, and WLAN-Group-Mgmt-Pairwise-Cipher
attributes defined in RFC 7268. These attributes are added to RADIUS
messages when the station negotiates use of WPA/RSN.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows external programs to use vendor specific information from
P2P peers without wpa_supplicant having to be able to parse and
understand all such vendor specific elements.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds following new control interface commands to allow arbitrary
vendor elements to be added into number of frames:
VENDOR_ELEM_ADD <frame id> <hexdump of elem(s)>
VENDOR_ELEM_GET <frame id>
VENDOR_ELEM_REMOVE <frame id> <hexdump of elem(s)>
VENDOR_ELEM_REMOVE <frame id> *
The following frames are supported in this commit (additional frames can
be added in the future):
0 = Probe Request frame in P2P device discovery
1 = Probe Response frame from P2P Device role
2 = Probe Response frame from P2P GO
3 = Beacon frame from P2P GO
4 = PD Req
5 = PD Resp
6 = GO Neg Req
7 = GO Neg Resp
8 = GO Neg Conf
9 = Invitation Request
10 = Invitation Response
11 = P2P Association Request
12 = P2P Association Response
One or more vendor element can be added/removed with the commands. The
hexdump of the element(s) needs to contain the full element (id, len,
payload) and the buffer needs to pass IE parsing requirements to be
accepted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the randomly generated bignum does not meet the validation steps, the
iteration loop in sae_get_rand() did not free the data properly. Fix the
memory leak by freeing the temporary bignum before starting the next
attempt at generating the value.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, the NL80211_ATTR_AKM_SUITES was skipped if either of these
SHA256-based AKMs was negotiated.
Signed-off-by: Jithu Jance <jithu@broadcom.com>
Extend the minimal HT 20/40 co-ex support to include dynamic changes
during the lifetime of the BSS. If any STA connects to a 2.4 GHz AP with
40 MHz intolerant bit set then the AP will switch to 20 MHz operating
mode.
If for a period of time specified by OBSS delay factor and OBSS scan
interval AP does not have any information about 40 MHz intolerant STAs,
the BSS is switched from HT20 to HT40 mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Move the definitions that depended in common.h into a separate header
file so that qca-vendor.h can be copied and used as-is in other
projects.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allocates a QCA vendor subcmd for extended statistics
functionality and also an attribute for delivering the payload
for extended statistics.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Rather than ignoring packets with a minimal 8-byte radiotap
header, which may occur elsewhere, tag generated (decrypted)
packets with an empty vendor namespace tag and ignore those.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows external programs to monitor driver signal change events
through wpa_supplicant when bgscan is used.
Signed-off-by: Jouni Malinen <j@w1.fi>
Only the Neighbor Report element should be included here, so verify that
the element id matches. In addition, verify that each subelement has
valid length before using the data.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes the definitions match the terminology used in IEEE Std
802.11-2012 and makes it easier to understand how the HT Operation
element subfields are used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This was used to fill in the "PSMP support" subfield that was defined
during P802.11n development. However, this subfield was marked reserved
in the published IEEE Std 802.11n-2009 and it is not supported by
current drivers that use hostapd for SME either. As such, there is not
much point in maintaining this field as ht_capab parameter within
hostapd either.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
QCA vendor extension is used for NAN functionality. This defines the
subcommand and attribute to address this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Following events are now sent to ctrl_iface monitors to indicate if
credential blocks have been added, modified, or removed:
CRED-ADDED <id>
CRED-MODIFIED <id> <field>
CRED-REMOVE <id>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows drivers that build the WPA/RSN IEs internally to use similar
design for building the OSEN IE.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This uses a QCA vendor extension to determine if the driver supports
fully offloaded DFS operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows hostapd to set a different management group cipher than the
previously hardcoded default BIP (AES-128-CMAC). The new configuration
file parameter group_mgmt_cipher can be set to BIP-GMAC-128,
BIP-GMAC-256, or BIP-CMAC-256 to select one of the ciphers defined in
IEEE Std 802.11ac-2013.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
As per IEEE Std 802.11ac-2013, 'Maximum A-MPDU Length Exponent' field
value is in the range of 0 to 7. Previous implementation assumed EXP0 to
be the maximum length (bits 23, 24 and 25 set) what is incorrect.
This patch adds options to set it up within the 0 to 7 range.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
There is no need to maintain a separate counter for this in addition to
the pointer to the current location. In addition, this gets rid of
warnings about unused variable write.
Signed-off-by: Jouni Malinen <j@w1.fi>
The special case of non-zero status code used in a GAS Comeback Response
frame to indicate that additional delay is needed before the response is
available was not working properly. This case needs to allow the status
code check to be bypassed for the comeback case prior to having received
any response data.
Signed-off-by: Jouni Malinen <j@w1.fi>
Move excluded SSID filtering step to the end of credential validation
process and return list of BSSes that would otherwise have matching
credentials, but have an excluded SSID. Automatic network selection will
not select such a network, but interworking_connect command can be used
to pick excluded networks.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant can request OSU icon data with "hs20_icon_request <BSSID>
<icon filename>". This transmits an Icon Request ANQP element and
processes the response in Icon Binary File ANQP elements.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Subscription remediation notification WNM-Notification Request is now
shown in the following way in wpa_supplicant control interface:
<3>HS20-SUBSCRIPTION-REMEDIATION http://example.com/foo/
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The HS 2.0 Indication element from wpa_supplicant now includes the
release number field and wpa_supplicant shows the release number of the
AP in STATUS command (hs20=1 replaced with hs20=<release>).
The new update_identifier field in the cred block can now be used to
configure the PPS MO ID so that wpa_supplicant adds it to the Indication
element in Association Request frames.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add IPv6 support when using udp/udp-remote control interface using the
following new build configuration options:
CONFIG_CTRL_IFACE=udp6
CONFIG_CTRL_IFACE=udp6-remote
This is useful for testing, while we don't need to assign IPv4 address
(static or using DHCP) and can just use auto configured IPv6 addresses
(link local, which is based on the MAC address). Also add scope id
support for link local case.
For example,
./wpa_cli
./wpa_cli -i ::1,9877
./wpa_cli -i fe80::203:7fff:fe05:69%wlan0,9877
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Confirm-before-commit validation step allowed execution to continue on
error case. This could result in segfault in sae_check_confirm() if the
temporary SAE data was not available (as it would not be, e.g., in case
of an extra SAE confirm message being received after successful
exchange). Fix this by stopping SAE processing immediately after
detecting unexpected state for confirm message. In addition, make the
public sae.c functions verify sae->tmp before dereferencing it to make
this type of bugs less likely to result in critical issues.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Instead of automatically triggering a connection, provide an indication
of one of the devices being a P2P client to upper layers to allow user
to determine what to do next.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Send a P2P-NFC-BOTH-GO event to upper layers to determine what to
do in case both devices going through NFC connection handover are
already operating as a GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This new mechanism allows P2P Client to request an IPv4 address from the
GO as part of the 4-way handshake to avoid use of DHCP exchange after
4-way handshake. If the new mechanism is used, the assigned IP address
is shown in the P2P-GROUP-STARTED event on the client side with
following new parameters: ip_addr, ip_mask, go_ip_addr. The assigned IP
address is included in the AP-STA-CONNECTED event on the GO side as a
new ip_addr parameter. The IP address is valid for the duration of the
association.
The IP address pool for this new mechanism is configured as global
wpa_supplicant configuration file parameters ip_addr_go, ip_addr_mask,
ip_addr_star, ip_addr_end. For example:
ip_addr_go=192.168.42.1
ip_addr_mask=255.255.255.0
ip_addr_start=192.168.42.2
ip_addr_end=192.168.42.100
DHCP mechanism is expected to be enabled at the same time to support P2P
Devices that do not use the new mechanism. The easiest way of managing
the IP addresses is by splitting the IP address range into two parts and
assign a separate range for wpa_supplicant and DHCP server.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a QCA vendor specific nl80211 event to allow the driver to
indicate a list of frequency ranges that should be avoided due to
interference or possible known co-existance constraints. Such
frequencies are marked as not allowed for P2P use to force groups to be
formed on different channels.
If a P2P GO is operating on a channel that the driver recommended not to
use, a notification about this is sent on the control interface and
upper layer code may decide to tear down the group and optionally
restart it on another channel. As a TODO item, this could also be changed
to use CSA to avoid removing the group.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This file is used as a registry of identifier assignments from the
Qualcomm Atheros OUI 00:13:74 for purposes other than MAC address
assignment. One of the first uses will be for nl80211 vendor
commands/events which is reason for the preparation change in
driver_nl80211.c
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The information of the peer's supported channel and operating class
is required for the driver to do TDLS off channel operations with a
compatible peer. Pass this information to the driver when the peer
station is getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new control interface command RADIO_WORK can be used by external
programs to request radio allocation slots from wpa_supplicant if
exclusive radio control is needed, e.g., for offchannel operations. If
such operations are done directly to the driver, wpa_supplicant may not
have enough information to avoid conflicting operations. This new
command can be used to provide enough information and radio scheduling
to avoid issues with such cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
The P2P_PRESENCE_REQ command did not give any easily available
indication of the response received from the GO. Make this more useful
by providing such response (if received) as a ctrl_iface monitor event
(P2P-PRESENCE-RESPONSE).
Signed-hostap: Jouni Malinen <j@w1.fi>
WPA_CIPHER_* and CIPHER_* are used for the exact same set of cipher
suites with the main difference being that the WPA_CIPHER_* version is
suitable to be used as a bitfield. Similarly, WPA_KEY_MGMT_* and
KEY_MGMT_* have similar design for AKMs. There is no need to maintain
two separate copies of the definitions since the bitfield compatible
version can be used for both needs. Get rid of the CIPHER_* and
KEY_MGMT_* versions to clean up the implementation by getting rid of
unnecessary mapping functions.
Signed-hostap: Jouni Malinen <j@w1.fi>
prime_len was added to the start pointer twice and because of this, the
actual y coordinate was not verified to be valid. This could also result
in reading beyond the buffer in some cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
These information elements are not really used anywhere in hostapd or
wpa_supplicant nor is there any plan to use them. As such, there is no
need to keep the code here either, so save couple of bytes here.
Signed-hostap: Jouni Malinen <j@w1.fi>
It was already possible to configure hostapd and wpa_supplicant to use
FT-SAE for the key management, but number of places were missing proper
AKM checks to allow FT to be used with the new AKM.
Signed-hostap: Jouni Malinen <j@w1.fi>
This prepares wpa_supplicant for accepting cases where the AP does not
use group addressed frames.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds initial parts for supporting the new GCMP-256, CCMP-256,
BIP-GMAC-128, BIP-GMAC-256, and BIP-CMAC-256 cipher suites.
Signed-hostap: Jouni Malinen <j@w1.fi>
The request retry loop only retries for 5 seconds, so any time
jumps would probably not affect it much, but it should be using
monotonic time nonetheless since it only cares about duration.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Based on priority, remove the connection with least priority whenever
a frequency conflict is detected.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
Despite interface (and group) related sockets are not used
for control, they are created and may be left.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Build CSA settings and call the driver to perform the switch. Construct
Beacon, Probe Response, and (Re)Association Response frames both for CSA
period and for the new channel. These frames are built based on the
current configuration. Add CSA IE in Beacon and Probe Response frames.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add a parameter to send the overlapping BSS scan parameter
information element. This will require clients to perform
background scans to check for neigbors overlapping this
HT40 BSS. Since the implementation is incomplete it should
only be used for testing.
Signed-hostap: Paul Stewart <pstew@chromium.org>
If we are already connected to the selected AP with a network block
that was created based on the selected credential, do not force a
reconnection or network block update.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Number of regressions had shown up in wpa_supplicant implementation of
SAE group selection due to different integer array termination (-1 in
hostapd, 0 in wpa_supplicant) being used for SAE groups. The
default_groups list did not seem to use any explicit termination value.
In addition, the sae_group_index was not cleared back to 0 properly
whenever a new SAE session was started.
Signed-hostap: Jouni Malinen <j@w1.fi>
Mask the remote VHT capabilities with our own capabilities, similarly
to what is done for HT capabilities.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
